Technical data
Technical data 24
Contents of this chapter
This chapter contains the technical specifications of the drive for frame sizes 4xR10 and
4R11, The specifications include ratings, sizes and technical requirements, provisions for
fulfiling the requirements for CE and other markings.
Ratings, Derating
‘The ratings of the drive module packages with 50 Hz and 60 Hz supply are given below.
TEC RATINGS
Frame | Input Output ratings
size | current Nominal use Light-duty use | Heavy-duty use,
ed Pu | Sy ha Pua | tne | Peo
aA lA. aA A | kw] eva) A kw A kw
‘2os0n | esRto | 2060 | 2540 | 288 | 2080 000] +408] 2001 | 1000 | 1480] 200
zaoona | amio| 200 | ave | acto | zaeo| r200] 56] 22ea | 1200 | 1755 | 00
zeson-a | ari | 2660 | 372 | 4048 | 2660] 1400] 1843| 2631 | +400 | 2089 | 1000
azsona| aan | 3200 | 04a | 4040 | 3200] ve00] 2230) o1e0 | 1600 | a55e"| 100
1G, = 500
zazoas| amo) 2020 | 2540 2601 | 2020[ v400] 1740] 1994] +400 +441 | 1000
za908-5 | 4xR10| 2390 | 2686 | a5t0 | 2390] 1600] 2018] 2293 | 1600 | 1755 | 1200
aaooas | aan | 2500 | 120 | «040 | 2500] ve00| zara] asoq | 1600 | 2oea | +4002 Technical data
IEC RATINGS:
Drive | Frame! input Output ratings
type | size current
‘acoso Nominal use Light-duty use| Heavy-duty use|
oaxt-
th | tae | Imaxstae) fe | Pu | Se | ha | Pla | tae | Pho
aA | al a allel a fw a) Kw
4mrt1 3230 [ 4048) 4048 | 3250 2000] 2707| 3154 | 2000 | 2565") 1800
v
Rio 1580 | 1987 | 2650 | 1500] 1400] taaa| 1546 | 1400 | 1925+] 1200
7| 4x1 1920 | 2521 | 249 | 1920/ 1800] 2295] 1058 | 1400 | 1674 | 1600
zi7oa7| 4st 2170 [ 2944) 3717 | 2470] 2000| 2593] 2101 | 2000 | 1058 | +800)
285087 | 411 25650 | 3036 | 4048 | 2650 2400] s167| 2594 | 2400 | 2101") 2000
‘3AX0 10000963510
Ux. | Nominal voltage ofthe dive. For input voltage range, see section Type designation key in the
hardware manual
h ‘Nominal input current (rms) at 40°C (104 *F)
'S, | Apparent power (no overload)
Maximum output current. Availabe for 10 seconds at start otherwise as long as allowed by drive
temperature. 140% ... 200% of lig, depending on power rating
Tra stan | Maximum output current at start, Available for two seconds only at stat every seven seconds if
‘start curent limits activated by parameter 30.18 Maximum start current
h Continuous ems output current. No overied capability at 40°C (108 *F). This is indicated in the
‘ype designation label ae ouut current
Fy _| Typical motor power in no-overload use
‘ha | Continuous ms output curent allowing 10% overload for t minute every § minutes,
Pie | Typical motor power for light overioad use
lh | Continuous rms output curent alowing 5c% overload for 1 minute every § minutes.
Paz | Typical motor power for heavy-duty use
* Continuous rms output curent allowing 40% overload for t minute every 6 minutes
~ | Continuous ms output current allowing 48% overload for 1 minute every 5 minutes.
+= | Continuous ms output curent allowing 44% overload for 1 minute every 5 minutes.
Note:
To achieve the rated motor power given inthe table, the rated current ofthe dive must be higher than or aqual
to tho rated motor current. The power ratings apply to most IEC 34 motors at the nominal voltage of the deve,
‘ABB recommends to select the drive, motor and gear combination forthe required motion profile with the
Diivetize dimensioning tot evaleble from ABE,