Professional Documents
Culture Documents
Basf Mastertop 1205 Tds PDF
Basf Mastertop 1205 Tds PDF
DESCRIPTION PACKAGING
MasterTop 1205 is a pigmented, solvent-free, MasterTop 1205 is supplied in 18 litre packs
high build epoxy floor coating system designed to (29.2kg)
offer seamless durable floor protection at applied Part A - 24kg
thicknesses between 0.2-0.4mm. Part B - 3.4kg
With the addition of MasterTop SR 3 (slip Colour pack - 1.8kg
resistant aggregates) between coats, anti-slip
resistant applications can be achieved in system COLOURS
build-up thicknesses between 0.5-1.0mm. Available in the following standard colours:
Light Grey, Dusty Grey, Oxide Red, Brilliant Blue,
PRIMARY USES Dark Green
MasterTop 1205 exhibits excellent wear, abrasion Other colours can be produced depending upon
and chemical resistance and is suitable for use in the quantity and in consultation with BASF’s
a wide variety of industrial and commercial Technical Services Department.
applications. It can be used to provide a surface
coating with a high gloss hygienic finish or a slip TYPICAL PROPERTIES*
resistant coating system.
Laboratory tests carried out at 25°C
MasterTop 1205 provides impermeable protection Pot life Approx. 35 mins
against common oils, greases, lubricants, aviation Initial cure 24 hours
fuels and hydraulic oils such as Skydrol. As in all Max. overcoating time 36 hours
corrosive situations, a full analysis of operating Final cure 7 days
and exposure conditions is required, followed by Full chemical resistance 7 days
reference to chemical resistance data to ensure Mixed density Approx. 1.6kg/litre
product suitability. Max service temperature 60°C
Flexural strength ASTM C580 40N/mm²
MasterTop 1205 can be used extensively in but is Tensile strength ASTM C307 20N/mm²
not limited to the following areas of application: Bond strength BS 1881 Part 207 >1.5N/mm²
STORAGE AND SHELF LIFE BASF reserves the right to have the true cause
Store out of direct sunlight, clear of the ground of any difficulty determined by accepted test
and on pallets. Protect from rainfall. Avoid methods.
excessive compaction and protect from
extremes of temperature. QUALITY AND CARE
All products originating from BASF’s Dubai, UAE
SAFETY PRECAUTIONS facility are manufactured under a management
As with all chemical products, care should be system independently certified to conform to the
taken during use and storage to avoid contact requirements of the quality, environmental and
with eyes, mouth, skin and foodstuffs (which occupational health & safety standards ISO
could be tainted during the curing/ drying phase 9001, ISO 14001 and OHSAS 18001.
of the product). Treat splashes to eyes and skin
immediately. If accidentally ingested, seek * Properties listed are based on laboratory controlled tests.
medical attention. Reseal the containers after
use. ® = Registered trademark of the BASF-Group in many countries.
BASF_CC-UAE/Top_1205_07_04/v7/08_15
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.
BASF Construction Chemicals UAE LLC Disclaimer: the LRQA mark relates
P.O. Box 37127, Dubai, UAE to certified management system and
Tel: +971 4 8090800, Fax: +971 4 8851002 not to the product mentioned on this
www.master-builders-solutions.basf.ae datasheet