Professional Documents
Culture Documents
Specialist finishes should not be applied to To achieve a smooth finish apply the
concrete, which contains more than 5% MASTERTOP 1210i M with a short hair roller
moisture, by mass. The substrate can be or squeegee, as a single coat at a minimum
considered sufficiently dry when the relative thickness of 0.5mm. To apply at thickness
humidity at the surface falls to 75% or less, greater than 0.5mm, use a pin screed or
when measured with a hygrometer to BS trowel.
8201:1981. The coating should be rolled with a spike
roller as soon as possible after application to
Guide to Application achieve a uniform finish. The applied coating
Prior to application, MASTERTOP 1210i M should be rolled a second time after 15-20
should be stored under cover and protected minutes. Continuous rolling does not harm
from extremes of temperature. Failure to do the product while it is still fluid.
this can cause inconsistent workability, finish Always wear spiked shoes when rolling the
and cure times for the mixed material. MASTERTOP 1210i M with a spiked roller.
Ideally, at least 24 hours before mixing,
MASTERTOP 1210i M should be Maintenance:
conditioned at approximately 20°C. To keep the floor in pristine condition, it
When working in cold conditions, do not should be treated with 2 or 3 coats of an
apply acrylic emulsion polish with a metallic base.
MASTERTOP 1210i M if the substrate or
ambient temperature cannot be maintained Yield
above 10°C for at least 10 days from the A 28.5kg unit will yield 18.62ltr of mixed
start of application. material.
Sealing: Watchpoints
All concrete surfaces to be overlaid with MASTERTOP 1210i M is suitable for
MASTERTOP 1210i M must be sealed with application to smooth surfaces only.
a coat of MASTERTOP 1200i M resin with
the addition of 0.5ltr of solvent. Add the Equipment care
sovlent to the base and reactor components, Remove uncured MASTERTOP 1210i M
after they have been decanted into the from tools and equipment using solvent.
mixing container; then mix the base and
reactor components together until all Storage
striations have disappeared. Apply the mixed Store out of direct sunlight, clear of the
material to the dry substrate at the rate of 6- ground on pallets protected from rainfall.
8m²/kg using a medium or short hair roller. Avoid excessive compaction and protect
Allow the sealer to become completely tack from extremes of temperatures. In tropical
free before over coating with MASTERTOP climates, the product must be stored in an
1210i M. air-conditioned environment.
Application:
MASTERTOP® 1210i M
Shelf Life
Up to 12 months if stored in unopened
containers according to manufacturer’s
instructions.
Note
Field service, where provided, does not
constitute supervisory responsibility. For
additional information, contact your local
MBT representative.
Quality Statement
All products manufactured by MBT Egypt, or
imported from MBT affiliate companies
world-wide, are manufactured to procedures
certified to conform to the quality
management systems described in the
ISO 9000 series.
12/04 MBT-EG
MBT, Egypt Tel.: +202 3453483/4 Whilst any information contained herein is true, accurate and
94 Shehab St. Mohandessin Fax: +202 3453481 Sales represents our best knowledge and experience, no warranty is given
Giza – Egypt Fax: +202 3453482 Admin. or implied with any recommendations made by us, our
Factory: Sadat City, Piece 118 Tel.: +2048 2604842 representatives or distributors, as the conditions of use and the
Zone 4 Fax: +2048 2604757 competence of any labour involved in the application are beyond our control.
As all MBT technical datasheets are updated on a regular basis, it is the user’s responsibility to obtain the most recent issue. Most recent issue is available on the website at
www.mbt-egypt.com