Professional Documents
Culture Documents
Valve Selection Guide PDF
Valve Selection Guide PDF
00-1
JANUARY 2009
2 © 2009 DeZURIK
3-Way and 4-Way Plug Valves Pump Check Valves
(PTW/PFW) Specially designed for precise flow regulation on
Design Features: 3-Way and 4-Way Plug Valves are pumping installations.
designed for throttling and diverting of clean, dirty,
viscous and corrosive liquids; sludge; abrasive and
fibrous slurries; clean and dirty corrosive gases.
Single and double plug styles can be arranged into Balancing Valves
a variety of flow combinations. Features include Specially designed for adjusting and reading flow
heavy-duty stainless steel bearings, long-life stem in condensers, and hot/chilled water systems of
seal, resilient plug facings for dead-tight shutoff, and heating and air conditioning systems.
metal plugs for high temperature applications.
3
Butterfly Valves
4
BOS-US Resilient-Seated BOS-CL Resilient-Seated
Butterfly Valves Butterfly Valves
Design Features: BOS Resilient-Seated Butterfly Design Features: BOS Resilient-Seated Butterfly
Valves are designed to handle a wide variety of Valves are designed to handle a wide variety of
liquids and gases. BOS-US Valves are available in liquids and gases. BOS-CL valves are available in
Ductile Iron-Lugged or wafer bodies with Ductile Lugged or wafer bodies with Ductile Iron/Nickel
Iron/Nickel Plated or 316 Stainless Steel discs. Plated or 316 Stainless Steel discs.
BOS-US Valves feature an uninterrupted seat BOS-CL valves feature an on-center disc; one-piece
design; one-piece body; solid, one-piece shaft and body; solid, one-piece shaft and a high-performance
high-performance resilient seat bonded to the body. resilient seat bonded to a solid backing ring.
Size Range: 2–20" (50 - 500mm) Size Range: 1½–24" (40 - 600mm)
Body Material: Ductile Iron 14-18" (350-450mm) 150 psi with DI disc (316
Stainless Steel 75 psi)
5
Rotary Control Valves
6
Knife Gate Valves
PPE Precision Electric Control Valve KGC Cast Stainless Steel Knife Gate
Design Features: The DeZURIK Precision Electric Design Features: Cast Stainless Steel Knife Gate
Control Valve is recognized industrywide as the Valves are designed for on-off and isolation services
most accurate and reliable basis weight control valve handling corrosive, abrasive and viscous liquids;
available. This high-resolution control valve is specifi- abrasive slurries, pulp stock, and dry materials. The
cally designed for critical paper stock control, and solid cast-bodied full port knife gate valve features
is used for basis weight and headbox level control a corrosion-resistant stainless steel body, gate,
applications. It provides unmatched control accuracy, stem and packing gland. Improved packing chamber
positioning and repeatability with up to 16,000 design. Cast-in guides and jams ensure long-lasting
repeatable positions. Accepts digital or analog operation. Resilient seats provide bubble-tight
signals. It features total electric operation with shutoff; metal seats meet TAPPI Leakage Rate
backlash that is essentially zero. Flange drilling is standards. Special v-orifice design available for
per ANSI standards. throttling applications.
Pressure Rating: 275 psi (1890 kPa) CWP Pressure Rating: 150 psi (1030 kPa) CWP
Body Material: 316 stainless steel Body Materials: 304, 316 and 317 stainless steel
Valve Style: V-port concentric or straight concentric Valve Style: Knife gate, lugged
plug, flanged
Actuator Type: Lever, handwheel, chainwheel, bevel
Actuator Type: AC synchronous motor or DC gear, cylinder, electric motor
stepping motor
7
KGN Cast Stainless Steel Knife Gate
Design Features: Cast stainless steel one piece body
with metal seat to meet the shut-off requirements of
TAPPI.
Seat Materials: Metal and Resilient 2-24" (50-600mm) -150 psi C.W.P. (1030 kPa)
End Connection: Lugged 30 & 36" (750 & 900mm) - 75 psi C.W.P. (520 kPa)
Actuator Type: Handwheels, chainwheels, bevel 42 & 48" (1100 & 1200mm) - 50 psi C.W.P. (345 kPa)
gears, pneumatic cylinders, hydraulic cylinders,
electric motors Actuator Type: Handwheels, Chainwheels, Bevel
Gears, Levers, Pneumatic and Hydraulic Cylinders
and electric motors.
8
KGL Stainless Steel Knife Gate KCB Bi-directional Knife Gate
Design Features: Cast/Fabricate Stainless Steel Design Features: A perimeter seat provides
Knife Gate Valves are designed for on-off and dead-tight shutoff in either direction and on dead
isolation services handling corrosive, abrasive and end service. Seat design eliminates pockets that trap
viscous liquids; abrasive slurries, pulp stock, and process media. Provides maximum flow capacity.
dry materials. The solid cast-bodied knife gate valve Resilient seats are locked into the valve body and
features a corrosion-resistant stainless steel body, provide guiding for the gate.
gate, stem and packing gland. Welded-in guides and
jams ensure long-lasting operation. Resilient seats Size Range: 2 - 36“ (50 - 900mm)
provide bubble-tight shutoff. Special v-orifice design
available for throttling applications. Temperature Range: 350°F (177°C)
Size Range: 2–72" (50–1800mm) Pressure Rating: 2 - 24" (50 - 600mm) 150 psi
(1030 kPa) CWP
Temperature Range: to 1000°F (540°C)
30" and 36" (750 & 900mm) 75 psi (520 kPa) CWP
Pressure Rating: 150 psi (1030 kPa) CWP
Body Material: 304 and 316 stainless steel
Body Materials: 304 and 316 stainless steel
Valve Style: Bi-directional knife gate, lugged
Valve Style: Knife gate, lugged
Actuator Type: Handwheel, chainwheel, bevel gear,
Actuator Type: Lever, handwheel, chainwheel, cylinder, electric motor
bevel gear, cylinder, electric motor
9
KGU Urethane Knife Gate KHP ANSI Class Knife Gate
Design Features: One-piece cast-in-place urethane DeZURIK ANSI Class Knife Gate Valves withstand
liner designed especially for handling abrasive high pressures and abrasive slurries found in mining
slurries and dry materials in the mining industry. (including oil sands processing), steel, power,
Provides drip-tight shutoff. Rugged stainless chemical, and paper industries. Ideal for isolation in
steel gate, long-life packing, stainless steel stem, high-pressure, high-density slurry lines, the valves
corrosion resistant yoke sleeve, and heavy-duty are pressure rated to ANSI Class 150 and 300.
superstructure.
Available in sizes from 6 - 36 inches (150 – 900mm),
Size Range: 4–24" (100–600mm) these High Performance Knife Gate Valves feature
cast carbon steel construction to meet demanding
Temperature Range: -40–180°F (82°C) performance requirements. Valves feature purge-
ports to allow flushing of media from the valve
Pressure Rating: 150 psi (1030 kPa) CWP interior. ANSI Class 150 valves match standard pipe
Body Materials: Cast iron with gates of 304, 316 IDs, and ANSI Class 300 valves match extra-strong
stainless steel pipe IDs. The seat/wear ring matches the pipeline
ID to reduce turbulence and pressure loss across
Valve Style: Urethane lined knife gate valve, wafer the valve. A wide variety of hardened trim options is
available on the gate, seat and the wear ring.
Actuator Type: Lever, handwheel, chainwheel,
cylinder, electric motor An integral bonnet is standard on ANSI Class 300
valves. To reduce maintenance costs, a pressure-
energized rod seal and heavy-duty braided scraper
ring are replaceable without removing the bonnet
or rod.
10
KLS Level Sensor Isolation Valve KCI Coal Burner Isolation Knife Gate
Design Features: Specially designed to mount Design Features: Specially designed to isolate
between the stock chest and the level sensor. pulverized coal burner lines on coal-fired boilers
Allows removal of sensor without draining stock during periodic maintenance shutdowns. Features
chest. Rachet or socket drive actuator allows close include rugged body construction, removable and
mounting of valve to tank. rotatable seat ring, stainless steel rising or non-rising
stem, and internal explosion pressure rating to 50
Size Range: 3" (80mm) psi (340 kPa) per NFPA standards. A variety of hard
faced seats for extended service life are available.
Temperature Range: to 450°C (233°C) ANSI 125/150, NFPA and Babcock & Wilcox end
Pressure Rating: 150 psi (1030 kPa) CWP connections available.
Body Materials: 316 and 317 stainless steel, Size Range: 6–24" (150–600mm)
Hastelloy C, 254 SMO stainless steel Pressure Rating: 150 psi (1030 kPa) CWP
Valve Style: Level sensor knife gate valve, lugged Temperature Range: On application
Actuator Type: Rachet handle or square drive with Body Materials: 304, 316 stainless steel
non-rising stem
Valve Style: Coal burner isolation knife gate valve
11
Special Service Consistency Transmitters
Gate Valves
SDP Rotating
Mixing and Diverting Knife Gate Valves Consistency
Available with either an integral body or a Transmitter
replaceable body. Valves with the replaceable body Design Features: Consistency
design are bolted to a Y-pattern pipe, allowing easy range from 0.75%
replacement of a single valve rather than the entire to 10% at velocities from 0.1
assembly. to 10 feet (.03 to 3 meters) per
second. Motor-driven sensor
They can be mounted in Y-pattern or Y-lateral
located in pulp stock flow is
configurations for either direct or reverse flow
highly sensitive to consistency
operation. Diverter valves with one inlet and two,
changes and insensitive to
three or four outlets are available in Y-pattern
flow changes. Capable
arrangements, with 60 or 90 degree angled valves.
of measuring consistency
Mixing valves are available with one outlet and two,
changes as small as
three or four inlets.
± .0025%.
Dust Collector Valves Chamber Size: 12–36" (300–900mm)
Specially designed cylinder actuated knife gate
valve with double packing and overlapping gates to Chamber Pressure Rating: 125 psi (860 kPa)
overcome the difficulties in handling steel mill blast
furnace dust. Chamber Material: 304, 316 or 317L stainless steel
12
Ported Gate Valves
13
Globe Valves
Size Range: 1–16” (25–400mm) Body Materials: 316 stainless steel, carbon steel,
cast iron
Temperature Range: -150–1200°F (-101–649°C)
ANSI Class Rating: 125–600
Body Materials: 316 stainless steel, cast iron, and
carbon steel Valve Style: 3-Way skirt guided globe valve
Valve Style: Cage guided globe with balanced or Actuator Type: Direct or reverse acting spring &
unbalanced plug diaphragm, springless diaphragm, electric motor
or manual handwheel
Trim Characteristics: Linear and equal percentage
14
Skirt Guided Globe Control Valves
Design Features: The Skirt Guided Globe Valve is an
economical general-purpose valve that offers rugged
reliability or tighter shutoff in low and medium
pressure applications.
15
Actuators
M-Series Actuators
G-Series Manual Actuators
M-Series Actuators are designed for use on smaller
DeZURIK Water Controls manual actuators are DeZURIK AWWA Butterfly Valves. The M-Series
constructed for dependable and lasting performance. Actuator meets the requirements of AWWA
Rugged worm gear design and heavy duty-corrosion C504 standards. The fully enclosed scotch yoke
resistant bearings provide easy valve operation and mechanism allows the M-Series Actuator to provide
reliable long life. Both above ground and buried a torque curve that matches the torque requirements
actuators are equipped with corrosion resistant of the valve. The thread system of the traveling
stainless steel input shaft and bolting as standard. nut is self-locking, maintaining disc position under
Housing is fully sealed and grease filled for varying flow conditions.
maintenance-free service.
MG-Series Actuators
Compact Actuators Manual Gear Actuators feature a ductile iron gear
Compact actuators are a versatile rack and pinion with sintered bronze bearings on each end of
design. The compact, modular design allows the the stainless steel input shaft for durability and
actuator to be mounted for a low profile assembly. performance.
16
PowerRac Cylinder Rotary Diaphragm
The rack and pinion design of PowerRac® Actuators DeZURIK Diaphragm Actuators are designed
provides high-operating torque for accurate control specifically for use on quarter-turn valves. They
in modulating services, and high opening torque for feature all steel, cast iron and stainless steel
on/off services. The unique square collet coupling construction for corrosion resistance in caustic
rigidly clamps the drive pinion to the valve shaft, environments. The actuators are designed for on/
eliminating backlash in the drive connection. This off or modulating service in either a fail-open or
rigid connection allows thrust from the cylinder to fail-closed mode. Action can be easily changed in
precisely position the valve. Positioners are solidly the field with no additional parts required. The spring
mounted on the actuator housing with a square nut, cartridge is cage retained at the factory for increased
feeding exact valve position directly to the positioner. safety. The output shaft is supported at the top and
No lost motion assures accurate valve positioning. bottom with bronze bearings that absorb side thrust
The modular design and compact size allow the and insure smooth, efficient, and accurate throttling
actuator to be close coupled to the valve. Standard control. Diaphragm Actuators are available with
ISO bolt circle allows PowerRac® Actuators to be safety lockout devices.
used on all DeZURIK quarter turn valves. Double-
acting or fail-safe spring-return cylinder options
available. PowerRac® Actuators are available with
safety lockout devices.
17
Valve Selection Chart
1 = Typical Application 2 = May Be Used 3 = Limited Application 4 = Not Used
Butterfly Plug
Gate Valves
Valves Valves
Standard
BOS 100% Port 3-Way (PTW) Ported
AWWA/ Port Knife
Resilient BHP Eccentric &
Application BAW Eccentric Gate Gate
Seated PEF 4-Way (PFW)
Requirements PEC
Function:
On-Off 1 1 1 1 1 4 1 1
Throttling 1 1 1 1 1 1 3 4
Diversion 3 3 3 4 4 1 4 4
Media:
Liquids (Clean) 1 1 1 1 1 1 1 3
Liquids (Dirty) 2 2 3 1 1 1 1 1
Liquids (Viscous) 2 1 2 1 1 1 1 1
Liquids (Corrosive) 4 2 1 1 1 1 2 1
Slurries (Sludge) 2 2 3 1 1 1 1 1
Liquids & Slurries
4 4 4 3 3 4 4 1
(Scaling)
Slurries (Abrasive) 4 3 2 2 2 2 1 1
Slurries (Fibrous) 4 2 2 2 2 1 1 1
High Pressure Steam
4 4 1 4 4 4 4 4
(+150lbs.)
Low Pressure Steam 4 4 1 3 4 3 4 3
Gasses (Clean) 1 1 1 1 1 1 2 2
Gasses (Dirty) 2 2 3 1 1 1 2 2
Gasses (Corrosive) 4 2 1 1 1 1 2 2
Dry Materials 4 2 4 2 2 4 1 1
Valve Characteristics:
High Flow Capacity 1 1 1 2 1 1 1 1
Low Head Loss
1 1 1 2 1 1 1 1
(Wide Open)
Low Torque/Thrust 2 2 1 2 2 1 2 2
High Temp., 800°F+ (425°C+) 4 4 3 3 4 4 1 4
Cryogenic 4 4 3 4 4 4 4 4
Erosion Resistance 4 3 2 1 1 3 1 1
Cavitation (Kc) @ 60% Open .35 .35 .35 .59 .59 N/A N/A N/A
Recovery Factor
.40 .40 .43 .70 .70 N/A N/A N/A
FL2 @ 60% Open
Note: This valve selection chart is designed to provide you with a quick reference on valve style capabilities. The chart considers both cost and
performance factors for a specific application when determining whether a valve style is rated Typical, May Be Used, or Limited Application.
For more information, contact DeZURIK or your local representative with your specific application requirements.
18
Valve Selection Chart
1 = Typical Application 2 = May Be Used 3 = Limited Application 4 = Not Used
Rotary V-Port
Skirt
Cage Guided Top Guided 3-Way Control Control
Application Guided
Valves Valve
Requirements
Function:
On-Off 1 1 1 4 1 2
Throttling 1 1 1 1 1 1
Diversion 4 4 4 1 4 4
Media:
Liquids (Clean) 1 1 1 1 1 1
Liquids (Dirty) 4 1 2 2 1 1
Liquids (Viscous) 4 1 1 1 1 1
Liquids (Corrosive) 1 1 1 1 1 1
Slurries (Sludge) 4 1 3 3 1 1
Liquids & Slurries
4 3 4 4 2 3
(Scaling)
Slurries (Abrasive) 4 3 4 4 1 3
Slurries (Fibrous) 4 4 4 4 4 1
High Pressure Steam
1 2 2 2 1 3
(+150lbs.)
Low Pressure Steam 1 1 1 1 1 1
Gasses (Clean) 1 1 1 1 1 1
Gasses (Dirty) 3 1 1 1 1 1
Gasses (Corrosive) 1 1 1 1 1 1
Dry Materials 4 4 4 4 4 4
Valve Characteristics:
High Flow Capacity 1 1 1 1 1 1
Low Head Loss
N/A N/A N/A N/A N/A 1
(Wide Open)
Low Torque/Thrust 1 2 3 3 2 1
High Temp., 800°F+ (425°C+) 2 1 3 3 3 4
Cryogenic 3 1 3 3 2 4
Erosion Resistance 4 2 3 3 1 3
Cavitation (Kc) @ 60% Open .61 .70 .80 .80 .60 .49
Recovery Factor FL @ 60% Open
2
.90 .94 .87 .87 .70 .61
ANSI II,
Shutoff Class ANSI II-VI ANSI IV-VI ANSI IV-VI ANSI IV ANSI IV-VI IV, VI OR
BETTER
ANSI ANSI ANSI ANSI ANSI ANSI
Pressure Rating
125-900/1500 125-900/1500 150-600 125-600 150-300 150 & 300
Note: This valve selection chart is designed to provide you with a quick reference on valve style capabilities. The chart considers both cost and
performance factors for a specific application when determining whether a valve style is rated Typical, May Be Used, or Limited Application.
For more information, contact DeZURIK or your local representative with your specific application requirements.
19
Sales and Service
For information about our worldwide locations, approvals, certifications and local representative:
Web Site: www.dezurik.com E-Mail: info@dezurik.com
250 Riverside Ave. N. Sartell, Minnesota 56377 • Phone: 320-259-2000 • Fax: 320-259-2227
DeZURIK reserves the right to incorporate our latest design and material changes without notice or obligation.
Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only
and should not be relied upon unless confirmed in writing by DeZURIK. Certified drawings are available upon request.