Professional Documents
Culture Documents
™
DYNOMAX SHOCK SUBS
DYNO-JAR TM
HYDRA-MECH
DYNOMAX SLIDE REAMERS
DYNOMAX REGULATORS
3rd Edition
Operations Manual: Revision 2019.03.22
(BACK OF COVER)
OPERATIONS MANUAL and TOOL SPECIFICATIONS - 3rd Edition
www.DYNOMAXDrillingTools.com sales@DYNOMAXDrillingTools.com
DYNOMAX Drilling Tools Inc. DYNOMAX Drilling Tools USA Inc. DYNOMAX Drilling Tools Inc. DYNOMAX Middle East LLC. IOT-DOSCO B.V.
7501 42 Street 2830 Farrell Rd. 309 Sawyer Road PO Box 333347 Boekel 36
Leduc, Alberta, Canada Houston, TX 77073 Estevan, Saskatchewan S4A 2H8 Dubai 1921 CE Akersloot
T9E 0R8 USA Canada United Arab Emirates The Netherlands
Tel: 780-986-3070 Tel: 832-486-9575 Tel: 306-634-4949 Tel: +971 48847550 Tel: 31-72-533 32 22
Fax: 780-986-3536 Fax: 832-486-9975 Fax: 306-634-4959 Fax: +971 48847551 Fax: 31-72-533 16 30
sales@DYNOMAXme.com sales@IOT-DOSCO.nl
Mission Statement
DYNOMAX Drilling Tools is committed to providing the highest quality of downhole tools with superior customer service to the industry.
This manual is available in electronic format. Please contact your local office. Revision 2019.03.22
TABLE OF CONTENTS 4 3-3/4 in (95 mm) 7-8 Lobe 2.3 Stage SERIES 152
INTRODUCTION10 3-3/4 in (95 mm) 7-8 Lobe 2.3 Stage HR SERIES 154
MOTOR OPERATIONS 5 in (127 mm) Bottom w/ 4-3/4 in (121 mm) 7-8 Lobe 3.8 Stage HR SERIES 256
RUNNING IN THE HOLE14 5 in (127 mm) 4-5 Lobe 6.0 Stage HR SERIES 258
ROTATING THE MOTOR 16 5 in (127 mm) 5-6 Lobe 4.0 Stage SERIES 260
DRILLING FLUIDS17 5 in (127 mm) 5-6 Lobe 4.0 Stage HR SERIES 262
DOWNHOLE TEMPERATURES18 5 in (127 mm) 5-6 Lobe 6.7 Stage HR SERIES 264
PULLING OUT OF THE HOLE TO LAY DOWN MOTOR19 5 in (127 mm) 5-6 Lobe 8.3 Stage HR SERIES 266
READING POWER SECTION CHARTS20 5 in (127 mm) 6-7 Lobe 6.0 Stage HR SERIES 268
BEARING PLAY22 5 in (127 mm) 6-7 Lobe 8.0 Stage HR SERIES 270
DYNOMAX MUD MOTORS 5 in (127 mm) 7-8 Lobe 2.0 Stage SERIES 272
1-11/16 in (43 mm) 5-6 Lobe 2.3 Stage SERIES 124 5 in (127 mm) 7-8 Lobe 2.6 Stage HR NP SERIES 274
2-7/8 in (73 mm) 2-3 Lobe 7.0 Stage SERIES 126 5 in (127 mm) 7-8 Lobe 2.6 Stage HR SERIES 276
2-7/8 in (73 mm) 5-6 Lobe 3.5 Stage SERIES 228 5 in (127 mm) 7-8 Lobe 3.7 Stage HR SERIES 278
2-7/8 in (73 mm) 5-6 Lobe 4.7 Stage HR SERIES 230 5 in (127 mm) 7-8 Lobe 3.8 Stage HR SERIES 280
3-1/8 in (79 mm) Bottom w/ 2-7/8 in (73 mm) 5-6 Lobe 3.3 Stage SERIES 132 5 in (127 mm) 7-8 Lobe 4.5 Stage HR SERIES 282
3-1/8 in (79 mm) 5-6 Lobe 3.2 Stage PVXT SERIES 134 5 in (127 mm) 7-8 Lobe 5.0 Stage HR SERIES 284
3-1/8 in (79 mm) 5-6 Lobe 3.5 Stage HR SERIES 1 36 5 in (127 mm) 8-9 Lobe 6.0 Stage HR SERIES 286
3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage SERIES 138 6-1/2 & 6-3/4 in (165 & 171 mm) 4-5 Lobe 7.0 Stage HR SERIES 188
3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage HR SERIES 140 6-1/2 & 6-3/4 in (165 & 171 mm) 6-7 Lobe 5.0 Stage HR SERIES 190
3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage SERIES 142 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.0 Stage HR SERIES 192
3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage HR SERIES 144 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.9 Stage HR SERIES 194
3-3/4 in (95 mm) 4-5 Lobe 3.5 Stage SERIES 146 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage SERIES 196
3-3/4 in (95 mm) 6-7 Lobe 1.7 Stage SERIES 148 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SERIES 198
3-3/4 in (95 mm) 6-7 Lobe 3.0 Stage SERIES 150 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SLOW SERIES 1100
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR SERIES 1102 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 2.9 Stage HR MUD LUBE152
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR SERIES 1104 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.0 Stage HR MUD LUBE154
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR SERIES 1106 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage HR MUD LUBE156
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR SERIES 1108 7 in (178 mm) 5-6 Lobe 5.3 Stage HR SERIES 3158
6-1/2 & 6-3/4 in (165 & 171 mm) 4-5 Lobe 7.0 Stage HR SERIES 3110 7 in (178 mm) 5-6 Lobe 8.1 Stage HR SERIES 3160
6-1/2 & 6-3/4 in (165 & 171 mm) 6-7 Lobe 5.0 Stage HR SERIES 3112 7 in (178 mm) 6-7 Lobe 6.5 Stage HR SERIES 3162
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.0 Stage HR SERIES 3114 7 in (178 mm) 6-7 Lobe 8.4 Stage HR SERIES 3164
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.9 Stage HR SERIES 3116 7 in (178 mm) 6-7 Lobe 11.4 Stage HR SERIES 3166
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage SERIES 3118 7 in (178 mm) 7-8 Lobe 8.5 Stage HR SERIES 3168
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SERIES 3120 7 in (178 mm) 9-10 Lobe 8.0 Stage HR SERIES 3170
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SLOW SERIES 3122 8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 1172
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR SERIES 3124 8 in (203 mm) 5-6 Lobe 3.0 Stage SERIES 1174
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR SERIES 3126 8 in (203 mm) 5-6 Lobe 3.0 Stage HR SERIES 1176
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR SERIES 3128 8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 1178
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR SERIES 3130 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1180
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.7 Stage HR SERIES 3132 8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 1182
6-3/4 in (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 2 SHORT 134 8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 1184
6-3/4 in (171 mm) 6-7 Lobe 5.0 Stage HR SERIES 2 SHORT 136 8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 1186
6-3/4 in (171 mm) 7-8 Lobe 2.9 Stage HR SERIES 2 SHORT 138 8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 1188
6-3/4 in (171 mm) 7-8 Lobe 5.0 Stage HR SERIES 2 SHORT 140 8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 1190
6-3/4 in (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 2 SHORT 142 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1192
6-3/4 in (171 mm) 9-10 Lobe 8.0 Stage HR SERIES 2 SHORT 144 8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 1194
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 3146 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1196
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 3148 8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 1198
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 9-10 Lobe 8.0 Stage HR SERIES 3150 8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 2200
5
TABLE OF CONTENTS
TABLE OF CONTENTS
6 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
8 in (203 mm) 5-6 Lobe 3.0 Stage SERIES 2202 8 in (203 mm) 7-8 Lobe 4.0 Stage HR MUD LUBE252
8 in (203 mm) 5-6 Lobe 3.0 Stage HR SERIES 2204 8 in (203 mm) 7-8 Lobe 5.9 Stage HR MUD LUBE254
8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 2206 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1256
8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 2208 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 1258
8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 2210 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1260
8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 2212 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1262
8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 2214 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 1264
8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 2216 9-5/8 in (244 mm) 3-4 Lobe 6.0 Stage SERIES 1266
8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 2218 9-5/8 in (244 mm) 6-7 Lobe 5.0 Stage SERIES 1268
8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 2220 9-5/8 in (244 mm) 6-7 Lobe 5.0 Stage HR SERIES 1270
8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 2222 9-5/8 in (244 mm) 6-7 Lobe 6.0 Stage SERIES 1272
8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 2224 9-5/8 in (244 mm) 6-7 Lobe 6.0 Stage HR SERIES 1274
8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 2226 9-5/8 in (244 mm) 7-8 Lobe 5.7 Stage HR SERIES 1276
8 in (203 mm) 4-5 Lobe 5.3 Stage HR MUD LUBE228 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1278
8 in (203 mm) 5-6 Lobe 3.0 Stage MUD LUBE230 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1280
8 in (203 mm) 5-6 Lobe 3.0 Stage HR MUD LUBE232 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1282
8 in (203 mm) 6-7 Lobe 4.0 Stage MUD LUBE234 11-1/4 in (286 mm) 5-6 Lobe 4.6 Stage SERIES 1284
8 in (203 mm) 6-7 Lobe 4.0 Stage HR MUD LUBE236 11-1/4 in (286 mm) 5-6 Lobe 4.6 Stage HR SERIES 1286
8 in (203 mm) 6-7 Lobe 5.0 Stage MUD LUBE238 11-1/4 in (286 mm) 6-7 Lobe 5.0 Stage HR SERIES 1- 9 5/8 in (244 mm) Rotor 288
8 in (203 mm) 6-7 Lobe 5.0 Stage HR MUD LUBE240 11-1/4 in (286 mm) 6-7 Lobe 5.5 Stage HR SERIES 1290
8 in (203 mm) 7-8 Lobe 2.0 Stage MUD LUBE242 OPTIONAL EQUIPMENT
8 in (203 mm) 7-8 Lobe 3.0 Stage MUD LUBE244 OFFSET FLEX SUB w/ BUTTONS & HARDBANDING 292
8 in (203 mm) 7-8 Lobe 3.0 Stage HR MUD LUBE246 ROTOR CATCH FLEX SUB w/ FLOAT AND HARDBANDING 292
8 in (203 mm) 7-8 Lobe 3.4 Stage HR MUD LUBE248 ROTOR CATCH FLOAT SUB w/ HARDBANDING 292
8 in (203 mm) 7-8 Lobe 4.0 Stage MUD LUBE250 DUMP SUB WITH FLOAT BORE w/ HARDBANDING 292
SCREW-ON KICK PAD 293 800SS02 - 8 in (203 mm) Series 2 Spring Configuration 2X2 307
SCREW-ON STABILIZER 293 800SS02 - 8 in (203 mm) LIGHT Series 2 Spring Configuration 1X1 308
SCREW-ON SPIRAL STABILIZER 293 800SS02 - 8 in (203 mm) LIGHT Series 2 Spring Configuration 2X2 308
DYNOMAX OIL-SEALED MOTOR CONNECTION TORQUES 294 950SS02 - 9 1/2 in (241 mm) Series 2 Spring Configuration 1X1 309
DYNOMAX SHOCK SUBS 950SS02 - 9 1/2 in (241 mm) Series 2 Spring Configuration 2X2 309
SHOCK SUB SERIES 2 OPERATING PROCEDURE296 950SS02 - 9 1/2 in (241 mm) LIGHT Series 2 Spring Configuration 1X1 310
287SS02 - 2 7/8 in (73 mm) Series 2 Spring Configuration 1X1 298 950SS02 - 9 1/2 in (241 mm) LIGHT Series 2 Spring Configuration 2X2 310
287SS02 - 2 7/8 in (73 mm) Series 2 Spring Configuration 2X2 298 1125SS02 - 11 1/4 in (286 mm) Series 2 Spring Configuration 1X1 311
312SS02 - 3 1/8in (79 mm) Series 2 Spring Configuration 1X1 299 1125SS02 - 11 1/4 in (286 mm) Series 2 Spring Configuration 2X2 311
312SS02 - 3 1/8in (79 mm) Series 2 Spring Configuration 2X2 299 DYNOMAX SHOCK SUB CONNECTION TORQUES 312
375SS02 - 3 3/4 in (95 mm) Series 2 Spring Configuration 1X1 300 DYNO-JAR™ HYDRA-MECH DRILLING JAR
375SS02 - 3 3/4 in (95 mm) Series 2 Spring Configuration 2X2 300 DYNO-JAR™ OPERATING PROCEDURE 313
475SS02 - 4 3/4 in (121 mm) Series 2 Spring Configuration 1X1 301 DMJ488314
475SS02 - 4 3/4 in (121 mm) Series 2 Spring Configuration 2X2 301 DMJ500314
500SS02 - 5 in (127 mm) Series 2 Spring Configuration 1X1 302 DMJ650315
500SS02 - 5 in (127 mm) Series 2 Spring Configuration 2X2 302 DMJ675315
650SS02 - 6 1/2 in (165 mm) Series 2 Spring Configuration 1X1 303 DMJ800316
650SS02 - 6 1/2 in (165 mm) Series 2 Spring Configuration 2X2 303 DYNO-JAR™ CONNECTION TORQUES 317
650SS02 - 6 1/2 in (165 mm) LIGHT Series 2 Spring Configuration 1X1 304 DYNOMAX SLIDE REAMERS
650SS02 - 6 1/2 in (165 mm) LIGHT Series 2 Spring Configuration 2X2 304 DYNOMAX SLIDE REAMERS 319
675SS02 - 6 3/4 in (171 mm) Series 2 Spring Configuration 1X1 305 DYNOMAX SLIDE REAMER FISHING DIMENSIONS 320
675SS02 - 6 3/4 in (171 mm) Series 2 Spring Configuration 2X2 305 DYNOMAX REGULATOR™
675SS02 - 6 3/4 in (171 mm) LIGHT Series 2 Spring Configuration 1X1 306 DYNOMAX REGULATOR™321
675SS02 - 6 3/4 in (171 mm) LIGHT Series 2 Spring Configuration 2X2 306 FISHING DIMENSIONS
800SS02 - 8 in (203 mm) Series 2 Spring Configuration 1X1 307 MOTOR FISHING DIMENSIONS - IMPERIAL (USC) 323
7
TABLE OF CONTENTS
TABLE OF CONTENTS
8 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
9
TABLE OF CONTENTS
INTRODUCTION
10 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
DynoMax Drilling Tools Inc. presents its 3rd edition of the Operations Manual and Tool Specifications. Changes and revisions include:
• Updated all DYNOMAX contact information. • 6.50", 6.75", and 7" Motor Series 3 added
• 5" Motor Series 1 removed • 5" Motor Series 2 added
• 8" Motor Mud Lube added • 4-7/8" Jar added, 2-7/8" Shock Sub added
• Motor Series no. has been identified in all titles • HR - Hard Rubber designation added in appropriate power sections
• Added Shock Tool Operation Instructions • Clarified Adjustable Instructions
• All power section performance curves updated to match suppliers • Added Regulator tool
• Updated all Fishing Drawings / Dimensions • Added Bearing End Play check section
The DynoMax Drilling Tools line of quality products includes drilling motors, shock subs, hydraulic mechanical drilling jars, slide reamers and Regulator
subs. Our Goal is to supply an assortment of quality downhole drilling tools designed to withstand today’s harsh drilling conditions at an economical
cost to our global customers.
This handbook is designed to demonstrate our current Drilling Tool Products, and outline the basic procedures and guidelines for the operation of our
downhole drilling tools.
The DynoMax oil sealed bearing assembly incorporates flow restrictor technology that reduces the pressure within the bearing assembly to a near-
balanced condition, reducing pressure across the rotary seals, thereby extending seal life. The flow restrictor is located above the bearing assembly
and allows approximately 5% of the drilling fluid to exit the assembly into the annulus, reducing internal pressure.
The DynoMax bearing assembly utilizes the patented Kalsi Rotary Seal - a seal that has been successfully proven in downhole drilling applications
for over 30 years.
All thrust bearings in the DynoMax assembly are custom-made, allowing DynoMax to maximize load capacity while not being restricted by the
availability of bearings.
Incorporating the latest in radial bearing technology allows DynoMax to increase the cross-sectional area of walls, and reduce the amount of moving
parts. This in turn allows DynoMax to increase the size of the internal drive line to handle an increased torque now required in today’s drilling
operations (I.e. Extended, Even Wall, and Hard Rubber power sections).
The DynoMax bearing assembly is designed to accommodate the use of various sizes and styles of screw-on stabilizers and kick pads (near bit) which
may be required in some drilling applications.
The DynoMax splined (gear) drive assembly (universal joint) is specially designed to distribute even load over the splines to transmit balanced torque
with reduced vibration.
The DynoMax adjustable bent housing assembly is surface-adjustable with settings from 0˚ to 3˚ in thirteen (13) increments. The optional fixed bent
11
INTRODUCTION
INTRODUCTION
12 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
housings allow for higher build-up rates (BUR) due to shorter bit-to-bend (BTB) as well as increased bending strength.
All critical components of DynoMax motors are manufactured from high strength alloy steel. These components are delivered with mill certificates
verifying the properties of the steel, which provides traceability through Quality Assurance numbers applied to the individual parts.
DynoMax Shock Subs range in size from 2⅞” (79 mm) through 11¼” (286 mm) O.D. The DynoMax Shock Sub contains a series of disc springs
designed to cushion the axial loading and maintain a constant weight on bit. This helps reduce drill bit vibration, extends drill-string life and bit life.
DynoMax Shock Subs have been utilized reliably with multiple friction-reduction systems, with consistent, proven results. Optional configurations are
available for light-duty applications where lower compression is needed.
DynoMax DYNO-JAR™ is a Hydraulic Mechanical Drilling Jar. It incorporates a mechanical latch assembly that holds the tool in a neutral position
and prevents unexpected jarring during tripping or drilling operations. The DYNO-JAR™ also features a hydraulic metering valve that creates a time
delay when the jar is in operation.
All DynoMax DYNO-JAR™ drilling jars feature the latest in ‘performance design’. DYNO-JARS have been designed to maximize oil flow to the top of the
tool, which will not only increase jarring impact with lighter pull on drill string, but it also increases safety as there is no need to have excessive overpull by
the drilling rig. The longer stroke length compared to most drilling jars maximizes jarring impact and increases the overall drill string movement. Pressure
compensation at the top and bottom of the tool increases jarring impacts because internal pressure can not buildup. This pressure compensation also
increases seal life due to zero pressure differential, while also minimizes pump-open force giving a more accurate pull calculation. The high-strength
latch assembly gives better jarring repeatability, and the improved DYNO-JAR™ latch design provides better wear characteristics which provide longer
life in extended jarring operations. Large oil reservoirs provide excellent lubrication during operation and help cool the jar components during use.
DynoMax DYNO-JAR™ drilling jars are designed to fit most mouse holes for ease of connection with drill strings.
DYNO-JARS are designed to:
Maximize oil flow through the tool
• Increase jarring impact with lighter pull on drill string
• Increase safety because there is no need to overpull the drilling rig
• Provide longer stroke than most drilling jars
• Maximize jarring impact
• Increase overall drill string movement
Pressure compensation top and bottom
• Increase jarring impact because internal pressure does not buildup.
• Increase seal life due to zero differential
• Minimize pump open force giving more accurate pull calculation
Improved Latch Design
• Better wear characteristics give longer life in extended jarring operations
• Stronger latch gives better jarring repeatability
Large Oil Reservoirs
• Provides excellent lubrication during operation
• Helps keep the jar cooler during use
The DynoMax Slide Reamer utilizes an integral blade design that provides 360 degree wall contact. The tool is designed to ream/condition while in a
slide operation (tripping in and out of the hole) as well as rotating. The tool also helps to reduce torque & drag by eliminating formation ledges, reducing
surface contact, and improving hole quality all while aiding in removing cuttings from the well. The Slide Reamer is also available in Non-Mag bodies for
use next to MWD/LWD tools.
13
INTRODUCTION
MOTOR OPERATIONS
14 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
The Regulator™ employs a variable size exit orifice to actively moderate the flow that goes through the motor continuously – extra fluid is vented out
the side. The exit orifice is controlled by a valve that measures the flow entering the motor. The valve mechanism responds in milliseconds so that flow
to the motor is always regulated. This can result in optimal motor performance, less stator failures, and saved time.
DynoMax Drilling Motors are designed for use in various drilling and remedial work applications in the Oil & Gas Industry, as well as the HDD Indus-
try (Utility and River Crossing). The DynoMax Mud Motor currently ranges in size from 2⅞” (73 mm) through 11¼” (286 mm) with a variety of rotor
and stator configurations, allowing our clients the versatility of matching the motor to specific drilling applications.
Applications include Directional and Horizontal drilling, Performance drilling (used on Drilling Rigs as well as Coiled Tubing), Coring, Reaming, Well
Servicing and Completions.
When selecting the correct motor and configurations for the application, it is important to consider hole size, drilling fluid, hole temperature, well profile
and bit selection.
RUNNING IN THE HOLE
When running in the hole, the traveling speed of the drillstring should be controlled to avoid contact with B.O.P.’s, wellheads, casing shoes, etc., and in
open hole for any suspected tight spots, ledges or excessive dog legs.
If tight spots are encountered and reaming is required, the motor should be run at minimum specified flow rates and minimum drillstring rotation.
Reduce the rate of running in the hole when approaching bottom so the motor does not run into solid cement or the bottom of the hole. Settled solids
at the bottom of the hole are common and can cause unexpected bit or motor damage.
Before tagging bottom, start the pumps and slowly raise flow rates to planned operation specifications, then slowly lower the assembly to apply Weight
On Bit (WOB). Adding WOB increases pump pressure.
** Always start pumps and break circulation prior to rotating drillstring and applying WOB (tagging bottom).
It is recommended to run the motor and drill bit for 10-15 minutes at reduced operating parameters, then slowly increase WOB until designed operations
are achieved.
Be aware of motor specifications and parameters to avoid exceeding Maximum Differential Pressure (Full Load). By exceeding recommended
parameters, one may cause the motor to stall. If motor stalling occurs, the following procedure should be applied:
• Stop all drillstring rotation immediately. Continued rotation will only increase torque in the assembly and cause severe power section (stator)
damage.
• Use the brake to slowly release torque in the drillstring as back offs may occur.
• Once you have lifted the drill bit off-bottom, gradually increase your pumps to original flow rates and continue drilling.
** Differential pressure is created by adding WOB. Once the pumps are started and desired flow rates are achieved, standpipe pressure will have
increased. As the motor is slowly lowered (adding WOB) the pressure will increase: this is what is known as Differential Pressure. The maximum
pressure allowed across the motor depends on motor size and configuration which are provided in this handbook.
15
MOTOR OPERATIONS
MOTOR OPERATIONS
16 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
** Always remember: the higher the bend, the lower the RPM.
Back Reaming
Back reaming should be avoided when possible. Reaming with minimal weight on bit induces high cyclical loads that can lead to premature damage of
the motor and its components.
If back reaming cannot be avoided the parameters at which tool is run should be closely monitored and controlled. Borehole quality, dog-leg severity,
motor bend setting, power section configuration and BHA stabilization are all major considerations to determine the parameters at which the tool will be
operated. As a general rule of thumb, flow rates should be reduced at least 30%. Rotary speeds should not exceed 40 RPM and this should be lowered
if bend settings above 1.50° are utilized. When parameters are required to exceed these recommendations there is always an increased possibility of
motor failure or damage to motor components which can include housing fracture or detected cracks, connection back-off, or damage to the bearings
of the tool.
DRILLING FLUIDS
Some drilling fluids and additives may be harmful to the stator elastomers of the power section, as well as the rotor and other components in the motor.
Care should be taken in selecting the power section best suited for drilling operations.
• If using acid-based fluids, the motor should be properly flushed when tripped out and sent for service as soon as possible.
• Solids should be controlled at all times and sand content should be less than 3%. Drilling fluids exceeding 3% will cause excessive erosion
resulting in reduced rotor and stator life, as well as washing of internal bearing assembly components.
• When drilling with fluids containing a chloride concentration over 30,000 ppm, the motor must be properly flushed and serviced as soon as
possible, as acids are formed increasing the corrosion of the internal motor components.
• Oil-based drilling fluids can be used, but will cause the elastomers in the stator to swell. It is recommended to reline after each run, as the
swelling will lead to higher compression which in turn leads to a heat buildup, eventual chunking of the stator, and motor failure.
17
MOTOR OPERATIONS
MOTOR OPERATIONS
18 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
DOWNHOLE TEMPERATURES
• Elastomers used in standard power sections are designed to operate in temperatures up to 116˚C (240˚F). If the operating temperature is
expected to exceed these limits, then an oversized power section should be considered. ‘Oversized power section’ means the rotor and stator
has more clearance, compensating for the elastomer to swell.
*** Note of Caution *** If for some reason the downhole temperature does not get hot, then the stator will not swell and motor will have
NO operating torque.
• It is also recommended to reline the stator if run in high temperature wells for any extended period of time.
• It is recommended that you reduce your operating differential pressures when working in elevated temperature conditions.
• When running a motor in the hole on hot temperature wells, periodic stops should be considered, circulating until reduced temperature fluid
passes through the motor should commence prior to reaching 100˚ C (212˚ F).
• Continuous circulation normally maintains the mud system at reduced temperatures, so periods of no circulation should be held to a minimum.
*** Note *** If running in high temperature wells on coiled tubing, flow rates should be held to a minimum.
PULLING OUT OF THE HOLE TO LAY DOWN MOTOR
It is good practice to circulate off-bottom and remove cuttings prior to tripping out of the hole. Caution should be taken when retrieving a bent motor/
drilling assembly through B.O.P.’s.
Once on surface, it is good practice to flush the motor with fresh water by: holding the bearing housing above the bit box, rotating the bit box clockwise,
while at the same time running water through to top of the motor. After a few minutes, stop the water flow; and continue rotating driveline until fluid stops
flowing though the bit box. Caution should be taken when rotating the bit box (should turn relatively easily), if bit box does not turn freely, discontinue
operation as this could cause internal connections to back off.
If motor is being laid down and considered for a re-run, it is essential to clean around the seal area near the bit box as well as the flow holes in the Piston
Housing (Located approximately 2-3 feet [0.6 - 1.0m] above the bit box).
For rerunning in cold weather it is recommended to ensure the sealing areas are free of debris. Fluid can freeze in these areas, resulting in seal damage
or stator damage if circulated through. The sealing areas and power section should be thawed prior to running in hole and circulated through.
Common practice is to steam the motor prior to running in hole. Ensure that the resulting temperature is not hot enough to damage the seals or stator
rubber.
19
MOTOR OPERATIONS
MOTOR OPERATIONS
20 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
No Load: When the motor is in the off-bottom position, with no weight on bit.
Full Load: When the motor is in the on-bottom position, and weight on bit is applied.
Differential Pressure: The difference in system pressure between No Load and Full Load positions. (Horizontal axis at bottom)
Max Differential Pressure: The maximum operating differential pressure including pressure losses across the tool. The value indicated in the chart
and table is based on water at 70°F (21°C) and optimum power section fit. Deviations in fluid density, operating temperatures, and operating conditions
should be considered and the maximum differential pressure value should be scaled accordingly. (Vertical black line indicated by the FULL LOAD 100%)
Torque: The torque output of the power section has a linearly increasing relationship with the differential pressure applied. An increase in differential
pressure will increase the torque up to the MAXIMUM DIFFERENTIAL PRESSURE line. (Grey sloped line with designation ‘TORQUE’)
Max Torque: The maximum torque that can be achieved when MAXIMUM DIFFERENTIAL PRESSURE is applied. (Grey line intersects the black line –
read to the right vertical axis)
Flow Rate: The charts and tables indicates the minimum, middle and maximum recommended flow rates for the power section. (Blue curved lines)
Speed: The charts and tables demonstrate the relationship between speed and differential pressure. For each flow rate, the curve displays how the
speed is reduced as the differential pressure is increased. (Left vertical axis)
Displacement: The number of rotor revolutions per unit of volume when no load is applied.
Power: The power output of the power section is determined by the torque output and speed parameters that the motor is operating at and can be deter-
mined by the calculation below.
6-1/2 in & 6-3/4 in (165 mm & 171 mm) 6-7 5.0 STAGE HR SERIES 1
200 9762
RPM x Torque 56 RPM x 9000 ft-lbs 600 GPM (2271 LPM) (13235)
HP = = = 96 HP 180 10000
5250 5250 (13558)
9000
160
(12202)
450 GPM (1703 LPM) 8000
140
(10846)
(8688)
SPEED (RPM)
6000
100 300 GPM (1136 LPM) (8135)
70%
20 TO
0
0 200 400 600 800 1000 1167 1200 1400
(1379) (2578) (4137) (5516) (6895) (8047)(8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
21
MOTOR OPERATIONS
MOTOR OPERATIONS
22 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
BEARING PLAY
The DynoMax Series Motor is a sealed bearing system that incorporates the use of a flow restrictor to help balance the pressure across the seals.
There should be minimal play in the stack when set down at surface. If checked when tripping out of the hole and prior to re-run, motors with more
than the following end play as shown in the table below should be laid down and returned for service.
23
MOTOR OPERATIONS
1-11/16 in (43 mm) 5-6 Lobe 2.3 Stage SERIES 1
24 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 1-11/16 in (43 mm) 5-6 2.3 STAGE SERIES 1
500 250
(2413)
(339)
350
400 42 GPM (158 LPM) 200
(271)
SPEED (RPM)
Bit Size Range 1-7/8 - 2-3/4 in 48 - 70 mm (203)
90
Bit Box Connection 1-1/4 REGULAR (130)
70%
Static TO
18,000 lbf 8007 daN
Max. Overpull (for re-run) 15,000lbf 6672 daN 0
0 100 200 300 400
(689) (1379) (2068)
Absolute Overpull 20,000 lbf 8896 daN (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
C = Overall (Rotor Catch/ 90 in 2286 mm
Float Sub)
Weight 40 lbs 18 kg Lobe Configuration 5-6 Lobe 2.3 Stage Flow Rate Speed
Displacement 9.250 rev/gal 2.444 rev/l GPM LPM RPM
Max Differential @ No Load 350 psi 2,413 kPa 20 76 150 - 182
Max Torque @ No Load 90 ft-lbs 122 Nm 30 117 268 - 286
Max Power 7 HP 5 kW 42 159 385 - 390
PAGE LEFT BLANK
INTENTIONALLY
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 25
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
2-7/8 in (73 mm) 2-3 Lobe 7.0 Stage SERIES 1
26 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 2-7/8 in (73 mm) 2-3 7.0 STAGE HR SERIES 1
1000 200
(6688)
(271)
970
900 70 GPM (265 LPM) 175
(237)
800 160
(217)
55 GPM (210 LPM)
700
SPEED (RPM)
Bit Size Range 3-5/8 - 3-7/8 in 92 - 98 mm (163)
40 GPM (150 LPM)
Bit Box Connection 2-3/8 REGULAR 500
70%
(54)
Static TO
37700 lbf 16770 daN 100
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 27
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
2-7/8 in (73 mm) 5-6 Lobe 3.5 Stage SERIES 2
28 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 2-7/8 in (73 mm) 5-6 3.5 STAGE SERIES 2
B 500 2000
A (BIT TO BEND) 120 GPM (454 LPM) (2712)
(BIT TO
STAB.) 450
(8964)
1300
400 1600
(2169)
350 1420
90 GPM (341 LPM) (1925)
SPEED (RPM)
Bit Size Range 3-5/8 - 3-7/8 in 92 - 98 mm (1627)
Bit Box Connection 2-3/8 REGULAR 250
60 GPM (227 LPM)
Dynamic 21505 lbf 9570 daN 200 800
70%
Bearing Load - Off Bottom TO
(542)
Static 64815 lbf 28830 daN 50
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 29
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
2-7/8 in (73 mm) 5-6 Lobe 4.7 Stage HR SERIES 2
30 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 2-7/8 in (73 mm) 5-6 4.7 STAGE HR SERIES 2
B 500 1000
A (BIT TO BEND) (1356)
(BIT TO
STAB.) 870
125 GPM (473 LPM) (1180)
400 800
(1065)
(7309)
1060
SPEED (RPM)
Bit Size Range 3-5/8 - 3-7/8 in 92 - 98 mm (814)
Bit Box Connection 2-3/8 REGULAR
Dynamic 21505 lbf 9570 daN 200
50 GPM (189 LPM)
400
70%
Static 64815 lbf 28830 daN
Max. Overpull for Re-run 49100 lbf 22000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 81800 lbf 36000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 1500 ft-lbs 2034 Nm
A = Bit To Stabilizer (center) N/A N/A
Lobe Configuration 5-6 Lobe 4.7 Stage HR Flow Rate Speed
Adjustable N/A N/A
B = Bit to Bend Displacement 3.32 rev/gal 0.88 rev/l GPM LPM RPM
Fixed 34.63 in 880 mm
Max Differential @ No Load 1,060 psi 7,308 kPa 50 189 110 - 170
C = Overall Length 188 in 4775 mm Max Torque @ No Load 870 ft-lbs 1,180 Nm 90 341 243 - 295
Weight 226 lbs 102.5 kg Max Power 62 HP 46 kW 125 473 375 - 420
PAGE LEFT BLANK
INTENTIONALLY
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 31
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) Bottom w/ 2-7/8 in (73 mm) 5-6 Lobe 3.3 Stage SERIES 1
32 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
2-7/8 in (73 mm) 5-6 3.3 STAGE SERIES 1 300
(BIT TO BEND) 500 (407)
(3378)
490
450 80 GPM (303 LPM)
250
400 (339)
350 200
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm 50 GPM (189 LPM)
Bit Box Connection 2-3/8 REGULAR 250
70%
Dynamic 28230 lbf 12560 daN 100
Bearing Load - Off Bottom UE
Static 83280 lbf 37040 daN 50 RQ
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.45 - - - - - 1.25 13.72 10.88 6.61 - - -
0.78 7.49 5.18 1.70 - - - 1.50 17.59 14.74 10.48 - - -
1.15 13.22 10.90 7.43 - - - 1.75 21.46 18.61 14.35 - - -
1.50 18.63 16.32 12.85 - - - 2.00 25.32 22.48 18.22 - - -
1.83 23.74 21.42 17.95 - - -
2.12 28.22 25.91 22.44 - - -
2.38 32.25 29.93 26.46 - - -
2.60 35.65 33.33 29.86 - - -
2.77 38.28 35.96 32.49 - - -
2.90 40.29 37.97 34.50 - - -
2.97 41.37 39.05 35.58 - - -
3.00 41.83 39.52 36.05 - - -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 33
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) 5-6 Lobe 3.2 Stage PVXT SERIES 1
34 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
3-1/8 in (79 mm) 5-6 3.2 STAGE PVXT SERIES 1
(BIT TO BEND) 400 1000
(1356)
140 GPM (530 LPM) 976
350 (1323)
800
(1085)
(6895)
300
1000
110 GPM (416 LPM)
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm (814)
80 GPM (303 LPM)
Bit Box Connection 2-3/8 REGULAR 200
70%
28230 lbf 12560 daN UE 200
Bearing Load - Off Bottom RQ (271)
TO
Static 83280 lbf 37040 daN 50
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.23 - - - - - 1.25 11.56 9.17 5.57 - - -
0.78 6.31 4.36 1.44 - - - 1.50 14.82 12.42 8.83 - - -
1.15 11.14 9.19 6.26 - - - 1.75 18.08 15.68 12.09 - - -
1.50 15.7 13.75 10.83 - - - 2.00 21.34 18.94 15.35 - - -
1.83 20 18.05 15.13 - - -
2.12 23.78 21.83 18.91 - - -
2.38 27.17 25.22 22.3 - - -
2.60 30.04 28.09 25.16 - - -
2.77 32.25 30.3 27.38 - - -
2.90 33.95 32 29.07 - - -
2.97 34.86 32.91 29.98 - - -
3.00 35.25 33.3 30.38 - - -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 35
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) 5-6 Lobe 3.5 Stage HR SERIES 1
36 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
3-1/8 in (79 mm) 5-6 3.5 STAGE HR SERIES 1
(BIT TO BEND) 500 1400
(1898)
450 210 GPM (795 LPM)
1200
400 (1627)
1110
(1505)
(5447)
1000
790
350
(1356)
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm 800
(1085)
Bit Box Connection 2-3/8 REGULAR 250
70%
Bearing Load - Off Bottom RQ 200
TO
Static 83280 lbf 37040 daN 50 (271)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND
ANGLE ANGLE Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 37
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage SERIES 1
38 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
3-1/8 in (79 mm) 7-8 3.0 STAGE SERIES 1
(BIT TO BEND) 300 800
(1085)
160 GPM (606 LPM) 732
250 (992)
600
(4137)
600
120 GPM (454 LPM) (814)
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm
80 GPM (303 LPM)
Bit Box Connection 2-3/8 REGULAR 150 400
(542)
70%
TO
Max. Overpull for Re-run 49100 lbf 22000 daN 0
0 100 200 300 400 500 600 700
Absolute Overpull 81800 lbf 36000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 2500 ft-lbs 3390 Nm
Adjustable 42.9 in 1090 mm
B = Bit to Bend Lobe Configuration 7-8 Lobe 3.0 Stage Flow Rate Speed
Fixed 34 in 864 mm
Displacement 1.69 rev/gal 0.45 rev/l GPM LPM RPM
C = Overall Length 188.3 in 4783 mm Max Differential @ No Load 600 psi 4,137 kPa 80 303 130 - 146
Weight 274 lbs 124.3 kg Max Torque @ No Load 732 ft-lbs 992 Nm 120 454 185 - 201
Max Power 33 HP 25 kW 160 606 240 - 255
ADJUSTABLE BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage SERIES 1 FBH BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2 Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2
(98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.11 - - - - - 1.25 10.45 8.29 5.04 - - -
0.78 5.71 3.94 1.3 - - - 1.50 13.4 11.24 7.99 - - -
1.15 10.07 8.31 5.66 - - - 1.75 16.35 14.18 10.93 - - -
1.50 14.2 12.44 9.79 - - - 2.00 19.3 17.13 13.88 - - -
1.83 18.09 16.33 13.68 - - -
2.12 21.51 19.74 17.1 - - -
2.38 24.57 22.81 20.16 - - -
2.60 27.16 25.4 22.76 - - -
2.77 29.17 27.4 24.76 - - -
2.90 30.7 28.94 26.29 - - -
2.97 31.52 29.76 27.11 - - -
3.00 31.88 30.11 27.47 - - -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 39
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage HR SERIES 1
40 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
3-1/8 in (79 mm) 7-8 3.0 STAGE HR SERIES 1
(BIT TO BEND) 300 1200
(1627)
1154
160 GPM (606 LPM) (1565)
(6203)
900
250 1000
(1356)
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm
80 GPM (303 LPM)
600
Bit Box Connection 2-3/8 REGULAR 150
(814)
70%
TO
Max. Overpull for Re-run 49100 lbf 22000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 81800 lbf 36000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516) (6203) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 2500 ft-lbs 3390 Nm
Adjustable 42.9 in 1090 mm
B = Bit to Bend Lobe Configuration 7-8 Lobe 3.0 Stage HR Flow Rate Speed
Fixed 34 in 864 mm
Displacement 1.69 rev/gal 0.45 rev/l GPM LPM RPM
C = Overall Length 188.3 in 4783 mm Max Differential @ No Load 900 psi 6,205 kPa 80 303 130 - 146
Weight 274 lbs 124.3 kg Max Torque @ No Load 1,154 ft-lbs 1,565 Nm 120 454 185 - 201
Max Power 53 HP 39 kW 160 606 240 - 255
ADJUSTABLE BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage HR SERIES 1 FBH BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 3.0 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2 Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2
(98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.11 - - - - - 1.25 10.45 8.29 5.04 - - -
0.78 5.71 3.94 1.3 - - - 1.50 13.4 11.24 7.99 - - -
1.15 10.07 8.31 5.66 - - - 1.75 16.35 14.18 10.93 - - -
1.50 14.2 12.44 9.79 - - - 2.00 19.3 17.13 13.88 - - -
1.83 18.09 16.33 13.68 - - -
2.12 21.51 19.74 17.1 - - -
2.38 24.57 22.81 20.16 - - -
2.60 27.16 25.4 22.76 - - -
2.77 29.17 27.4 24.76 - - -
2.90 30.7 28.94 26.29 - - -
2.97 31.52 29.76 27.11 - - -
3.00 31.88 30.11 27.47 - - -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 41
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage SERIES 1
42 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
3-1/8 in (79 mm) 7-8 4.0 STAGE SERIES 1
(BIT TO BEND) 450 500
110 GPM (416 LPM) (678)
437
400 (592)
(5171)
400
750
90 GPM (341 LPM)
350 (407)
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm 250 (407)
Bit Box Connection 2-3/8 REGULAR
70%
Bearing Load - Off Bottom UE
(136)
Static 83280 lbf 37040 daN 50 RQ
TO
Max. Overpull for Re-run 49100 lbf 22000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 81800 lbf 36000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 2500 ft-lbs 3390 Nm
Adjustable 42.9 in 1090 mm
B = Bit to Bend Lobe Configuration 7-8 Lobe 4.0 Stage Flow Rate Speed
Fixed 34 in 864 mm
Displacement 3.71 rev/gal 0.98 rev/l GPM LPM RPM
C = Overall Length 156.3 in 3970 mm Max Differential @ No Load 750 psi 5,171 kPa 70 265 240 - 263
Weight 250 lbs 113.4 kg Max Torque @ No Load 437 ft-lbs 592 Nm 90 341 315 - 339
Max Power 32 HP 24 kW 110 416 390 - 415
ADJUSTABLE BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage SERIES 1 FBH BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2 Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2
(98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.33 - - - - - 1.25 12.53 9.93 6.04 - - -
0.78 6.84 4.73 1.56 - - - 1.50 16.06 13.46 9.57 - - -
1.15 12.07 9.96 6.79 - - - 1.75 19.59 17 13.1 - - -
1.50 17.02 14.9 11.73 - - - 2.00 23.12 20.53 16.64 - - -
1.83 21.68 19.56 16.39 - - -
2.12 25.77 23.66 20.49 - - -
2.38 29.45 27.33 24.16 - - -
2.60 32.55 30.44 27.27 - - -
2.77 34.95 32.84 29.67 - - -
2.90 36.79 34.68 31.51 - - -
2.97 37.78 35.66 32.49 - - -
3.00 38.2 36.09 32.92 - - -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 43
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage HR SERIES 1
44 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
B
(OVERALL LENGTH)
3-1/8 in (79 mm) 7-8 4.0 STAGE HR SERIES 1
(BIT TO BEND) 450 800
110 GPM (416 LPM) (1220)
690
400 700 (936)
(949)
(7757)
1125
90 GPM (341 LPM)
350 600
(814)
SPEED (RPM)
Bit Size Range 3-7/8 - 4-1/2 in 98 - 114 mm 250
(678)
400
Bit Box Connection 2-3/8 REGULAR (542)
70%
Bearing Load - Off Bottom UE 100
Static 83280 lbf 37040 daN 50 RQ (136)
TO
Max. Overpull for Re-run 49100 lbf 22000 daN 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
Absolute Overpull 81800 lbf 36000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516) (6203) (6895) (7585) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 2500 ft-lbs 3390 Nm
Adjustable 42.9 in 1090 mm
B = Bit to Bend Lobe Configuration 7-8 Lobe 4.0 Stage HR Flow Rate Speed
Fixed 34 in 864 mm
Displacement 3.71 rev/gal 0.98 rev/l GPM LPM RPM
C = Overall Length 156.3 in 3970 mm Max Differential @ No Load 1,125 psi 7,757 kPa 70 265 240 - 263
Weight 250 lbs 113.4 kg Max Torque @ No Load 690 ft-lbs 936 Nm 90 341 315 - 339
Max Power 51 HP 38 kW 110 416 390 - 415
ADJUSTABLE BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage HR FBH BUILD RATE: 3-1/8 in (79 mm) 7-8 Lobe 4.0 Stage HR
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2 Size 3-7/8 4-1/8 4-1/2 3-7/8 4-1/8 4-1/2
(98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm) (98 mm) (105 mm) (114 mm)
BEND BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) ANGLE
0.39 6.84 4.73 1.56 - - - 1.25 16.06 13.46 9.57 - - -
0.78 12.07 9.96 6.79 - - - 1.50 19.59 17 13.1 - - -
1.15 17.02 14.9 11.73 - - - 1.75 23.12 20.53 16.64 - - -
1.50 21.68 19.56 16.39 - - - 2.00 26.66 24.06 20.17 - - -
1.83 25.77 23.66 20.49 - - -
2.12 29.45 27.33 24.16 - - -
2.38 32.55 30.44 27.27 - - -
2.60 34.95 32.84 29.67 - - -
2.77 36.79 34.68 31.51 - - -
2.90 37.78 35.66 32.49 - - -
2.97 38.2 36.09 32.92 - - -
3.00 38.2 36.09 32.92 - - -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This infomation is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 45
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-3/4 in (95 mm) 4-5 Lobe 3.5 Stage SERIES 1
46 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 3-3/4 in (95 mm) 4-5 3.5 STAGE HR SERIES 1
B
A (BIT TO BEND) 160 GPM (606 LPM)
(BIT TO 240 1500
STAB.) (2034)
1430
(1940)
120 GPM (454 LPM)
180 1050
790
SPEED (RPM)
Bit Size Range 4-3/4 - 5-7/8 in 121 - 149 mm
80 GPM (303 LPM)
Bit Box Connection 2-7/8 REGULAR 120 700
70%
Bearing Load - Off Bottom UE
Static 104100 lbf 46310 daN RQ
TO
Max. Overpull for Re-run 154100 lbf 69000 daN 0
0 200 400 600 800 1000
Absolute Overpull 256800 lbf 114000 daN (1379) (2758) (4137) (5515) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 3500 ft-lbs 4800 Nm
A = Bit To Stabilizer (center) 10 in 254 mm
Lobe Configuration 4-5 Lobe 3.5 Stage HR Flow Rate Speed
Adjustable 50.6 in 1285 mm
B = Bit to Bend Displacement 1.55 rev/gal 0.41 rev/l GPM LPM RPM
Fixed 41.5 in 1054 mm
Max Differential @ No Load 790 psi 5,430 kPa 80 303 80 - 123
C = Overall Length 228.7 in 5809 mm Max Torque @ No Load 1430ft-lbs 1,940 Nm 120 454 148 - 185
Weight 422 lbs 191.4 kg Max Power 63 HP 47 kW 160 606 200- 250
ADJUSTABLE BUILD RATE: 3 3/4 in (95 mm) 4-5 Lobe 3.5 Stage SERIES 1 FBH BUILD RATE: 3 3/4 in (95 mm) 4-5 Lobe 3.5 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 4-3/4 5-7/8 4-3/4 5-7/8 Size 4-3/4 5-7/8 4-3/4 5-7/8
(121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) -
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.18 - - 0.01 1.43 - 1.25 7.82 1.43 - 8.88 8.72 -
0.78 3.95 - - 3.98 4.51 - 1.50 11.00 5.23 - 11.64 10.79 -
1.15 7.52 2.14 - 8.23 7.43 - 1.75 12.65 6.26 - 14.41 12.99 -
1.50 10.90 5.02 - 12.25 10.82 - 2.00 15.06 8.68 - 17.18 15.76 -
1.83 14.09 8.71 - 16.04 14.61 -
2.12 16.89 11.51 - 19.36 17.94 -
2.38 19.40 14.02 - 22.35 20.92 -
2.60 21.53 16.14 - 24.87 23.45 -
2.77 23.17 17.78 - 26.82 25.40 -
2.90 24.42 19.04 - 28.31 26.89 -
2.97 25.10 19.71 - 29.12 27.69 -
3.00 25.39 20.00 - 29.46 28.03 -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 47
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-3/4 in (95 mm) 6-7 Lobe 1.7 Stage SERIES 1
48 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 3-3/4 in (95 mm) 6-7 1.7 STAGE SERIES 1
B 200 1200
A (BIT TO BEND) 160 GPM (606 LPM) (1627)
(BIT TO 986
STAB.) (1337)
1000
120 GPM (454 LPM) (1356)
150
800
SPEED (RPM)
Bit Size Range 4-3/4 - 5-7/8 in 121 - 149 mm
600
Bit Box Connection 2-7/8 REGULAR 100
(814)
70%
Bearing Load - Off Bottom UE (271)
Static 104100 lbf 46310 daN RQ
TO
Max. Overpull for Re-run 154100 lbf 69000 daN 0
0 100 200 300 400 500
Absolute Overpull 256800 lbf 114000 daN (690) (1379) (2069) (2758) (3448)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 3500 ft-lbs 4800 Nm
A = Bit To Stabilizer (center) 10 in 254 mm
Lobe Configuration 6-7 Lobe 1.7 Stage Flow Rate Speed
Adjustable 50.6 in 1285 mm
B = Bit to Bend Displacement 1.00 rev/gal 0.26 rev/l GPM LPM RPM
Fixed 41.5 in 1054 mm
Max Differential @ No Load 432 psi 2,979 kPa 80 303 69 - 80
C = Overall Length 170.7 in 4336 mm Max Torque @ No Load 986 ft-lbs 1,337 Nm 120 454 109 - 120
Weight 313 lbs 142 kg Max Power 28 HP 21 kW 160 606 148 - 160
ADJUSTABLE BUILD RATE: 3 3/4 in (95 mm) 6-7 Lobe 1.7 Stage SERIES 1 FBH BUILD RATE: 3 3/4 in (95 mm) 6-7 Lobe 1.7 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 4-3/4 5-7/8 4-3/4 5-7/8 Size 4-3/4 5-7/8 4-3/4 5-7/8
(121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) -
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.24 - - 0.13 2.7 - 1.25 10.37 1.9 - 12.15 11.86 -
0.78 5.23 - - 5.5 6.44 - 1.50 13.57 5.1 - 15.99 14.44 -
1.15 9.97 2.84 - 11.45 9.99 - 1.75 16.77 8.3 - 19.82 17.25 -
1.50 14.46 7.32 - 17.08 14.5 - 2.00 19.97 11.5 - 23.66 21.09 -
1.83 18.68 11.55 - 22.38 19.81 -
2.12 22.4 15.26 - 27.04 24.47 -
2.38 25.73 18.59 - 31.22 28.65 -
2.60 28.54 21.4 - 34.76 32.18 -
2.77 30.72 23.58 - 37.49 34.92 -
2.90 32.38 25.24 - 39.58 37.01 -
2.97 33.28 26.14 - 40.7 38.13 -
3.00 33.66 26.52 - 41.19 38.61 -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 49
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-3/4 in (95 mm) 6-7 Lobe 3.0 Stage SERIES 1
50 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 3-3/4 in (95 mm) 6-7 3.0 STAGE SERIES 1
B 180 1350
A (BIT TO BEND) (1627)
(BIT TO
200 GPM (757 LPM) 1315
STAB.) 160 1200 (1783)
(1356)
140 1050
(3999)
(1356)
580
SPEED (RPM)
Bit Size Range 4-3/4 - 5-7/8 in 121 - 149 mm 100 750
(1065)
Bit Box Connection 2-7/8 REGULAR
80 600
Dynamic 31850 lbf 14170 daN 80 GPM (303 LPM)
(814)
Dynamic 40 300
31850 lbf 14170 daN
70%
(542)
Bearing Load - Off Bottom UE
Static 104100 lbf 46310 daN 20 RQ 150
TO (271)
Max. Overpull for Re-run 154100 lbf 69000 daN 0
0 100 200 300 400 500 600
Absolute Overpull 256800 lbf 114000 daN (690) (1379) (2069) (2758) (3448) (4137)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 3500 ft-lbs 4800 Nm
A = Bit To Stabilizer (center) 10 in 254 mm
Lobe Configuration 6-7 Lobe 3.0 Stage Flow Rate Speed
Adjustable 50.6 in 1285 mm
B = Bit to Bend Displacement 0.69 rev/gal 0.18 rev/l GPM LPM RPM
Fixed 41.5 in 1054 mm
Max Differential @ No Load 580 psi 3,999 kPa 80 303 50 - 64
C = Overall Length 253.7 in 6444 mm Max Torque @ No Load 1,315 ft-lbs 1,783 Nm 140 530 98 - 110
Weight 461 lbs 209.1 kg Max Power 37 HP 27 kW 200 757 146 - 155
ADJUSTABLE BUILD RATE: 3 3/4 in (95 mm) 6-7 Lobe 3.0 Stage SERIES 1 FBH BUILD RATE: 3 3/4 in (95 mm) 6-7 Lobe 3.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 4-3/4 5-7/8 4-3/4 5-7/8 Size 4-3/4 5-7/8 4-3/4 5-7/8
(121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) -
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.16 - - - 1.14 - 1.25 7.07 1.29 - 7.95 7.82 -
0.78 3.57 - - 3.56 3.99 - 1.50 9.25 3.48 - 10.42 9.73 -
1.15 6.8 1.93 - 7.34 6.69 - 1.75 11.44 5.66 - 12.89 11.74 -
1.50 9.86 4.99 - 10.91 9.76 - 2.00 13.62 7.84 - 15.37 14.21 -
1.83 12.74 7.87 - 14.28 13.13 -
2.12 15.27 10.41 - 17.24 16.09 -
2.38 17.54 12.68 - 19.9 18.74 -
2.60 19.46 14.6 - 22.14 20.99 -
2.77 20.95 16.08 - 23.88 22.72 -
2.90 22.08 17.21 - 25.21 24.05 -
2.97 22.69 17.83 - 25.92 24.76 -
3.00 22.95 18.09 - 26.23 25.07 -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 51
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-3/4 in (95 mm) 7-8 Lobe 2.3 Stage SERIES 1
52 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 3-3/4 in (95 mm) 7-8 2.3 STAGE SERIES 1
B 140 1200
A (BIT TO BEND) (1627)
(BIT TO 160 GPM (605 LPM)
STAB.) 1110
120 (1505)
900
100 120 GPM (454 LPM) (1220)
(2413)
70%
Dynamic 31850 lbf 14170 daN RQ (407)
TO
Bearing Load - Off Bottom 20
Static 104100 lbf 46310 daN
Max. Overpull for Re-run 154100 lbf 69000 daN 0
0 100 200 300 400
Absolute Overpull 256800 lbf 114000 daN (690) (1379) (2069) (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 3500 ft-lbs 4800 Nm
A = Bit To Stabilizer (center) 10 in 254 mm
Lobe Configuration 7-8 Lobe 2.3 Stage Flow Rate Speed
Adjustable 50.6 in 1285 mm
B = Bit to Bend Displacement 0.77 rev/gal 0.20 rev/l GPM LPM RPM
Fixed 41.5 in 1054 mm
Max Differential @ No Load 350 psi 2,413 kPa 80 303 50 - 61
C = Overall Length 234.7 in 5961 mm Max Torque @ No Load 1,110 ft-lbs 1,505 Nm 120 454 80 - 96
Weight 438 lbs 198.7 kg Max Power 23 HP 17 kW 160 606 110 - 130
ADJUSTABLE BUILD RATE: 3 3/4 in (95 mm) 7-8 Lobe 2.3 Stage SERIES 1 FBH BUILD RATE: 3 3/4 in (95 mm) 7-8 Lobe 2.3 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 4-3/4 5-7/8 4-3/4 5-7/8 Size 4-3/4 5-7/8 4-3/4 5-7/8
(121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) - (121 mm) (149 mm) -
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.18 - - - 1.35 - 1.25 7.63 1.4 - 8.63 8.48 -
0.78 3.85 - - 3.87 4.37 - 1.50 9.98 3.75 - 11.33 10.51 -
1.15 7.34 2.09 - 8 7.23 - 1.75 12.34 6.11 - 14.02 12.66 -
1.50 10.63 5.38 - 11.9 10.55 - 2.00 14.69 8.46 - 16.71 15.35 -
1.83 13.74 8.49 - 15.58 14.22 -
2.12 16.47 11.22 - 18.81 17.46 -
2.38 18.92 13.67 - 21.71 20.35 -
2.60 20.99 15.74 - 24.16 22.8 -
2.77 22.59 17.34 - 26.05 24.7 -
2.90 23.82 18.57 - 27.5 26.15 -
2.97 24.48 19.23 - 28.28 26.93 -
3.00 24.76 19.51 - 28.61 27.26 -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 53
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
3-3/4 in (95 mm) 7-8 Lobe 2.3 Stage HR SERIES 1
54 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 3-3/4 in (95 mm) 7-8 2.3 STAGE HR SERIES 1
B 140 2100
(3570)
A (BIT TO BEND) (2847)
520
(BIT TO 160 GPM (605 LPM)
STAB.)
120 1800
(2440)
1670
(2260)
100 120 GPM (454 LPM) 1500
(2034)
70%
Dynamic 31850 lbf 14170 daN UE
Bearing Load - Off Bottom RQ
20 TO 300
Static 104100 lbf 46310 daN (407)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.18 - - - 1.35 - 1.25 7.63 1.4 - 8.63 8.48 -
0.78 3.85 - - 3.87 4.37 - 1.50 9.98 3.75 - 11.33 10.51 -
1.15 7.34 2.09 - 8 7.23 - 1.75 12.34 6.11 - 14.02 12.66 -
1.50 10.63 5.38 - 11.9 10.55 - 2.00 14.69 8.46 - 16.71 15.35 -
1.83 13.74 8.49 - 15.58 14.22 -
2.12 16.47 11.22 - 18.81 17.46 -
2.38 18.92 13.67 - 21.71 20.35 -
2.60 20.99 15.74 - 24.16 22.8 -
2.77 22.59 17.34 - 26.05 24.7 -
2.90 23.82 18.57 - 27.5 26.15 -
2.97 24.48 19.23 - 28.28 26.93 -
3.00 24.76 19.51 - 28.61 27.26 -
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 55
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) Bottom w/ 4-3/4 in (121 mm) 7-8 Lobe 3.8 Stage HR SERIES 2
56 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 4-3/4 in (121 mm) 7-8 3.8 STAGE HR SERIES 2
B 140 6000
A (BIT TO BEND) 250 GPM (946 LPM) (8135)
(BIT TO 4965
STAB.)
(6732)
120 5000
(7481)
1085
(6779)
100
175 GPM (663 LPM) 4000
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm 80
70%
RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 3.8 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.52 rev/gal 0.14 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,085 psi 7,481 kPa 100 379 42 - 52
C = Overall Length 295.3 in 7501 mm Max Torque @ No Load 4,965 ft-lbs 6,732 Nm 175 662 82 - 91
Weight 1094 lbs 496.2 kg Max Power 115 HP 89 kW 250 946 122 - 130
ADJUSTABLE BUILD RATE: 5 in (127 mm) Bottom w/ 4-3/4 in (121 mm) 7-8 Lobe 3.8 FBH BUILD RATE: 5 in (127 mm) Bottom w/ 4-3/4 in (121 mm) 7-8 Lobe 3.8 Stage HR
Stage HR SERIES 2 SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.21 1.8 1.38 0.96 0.72 0.74 0.84 0.94 1.25 8.53 8.03 7.53 7.03 7.76 7.67 7.57 7.47
0.78 5.14 4.73 4.31 3.89 4.07 3.98 3.88 3.78 1.50 10.41 9.91 9.41 8.91 9.84 9.74 9.65 9.55
1.15 7.92 7.5 7.09 6.67 7.25 7.16 7.06 6.96 1.75 12.28 11.79 11.29 10.79 11.92 11.82 11.72 11.63
1.50 10.55 10.13 9.72 9.3 10.26 10.17 10.07 9.97 2.00 14.16 13.66 13.16 12.67 14 13.9 13.8 13.7
1.83 13.03 12.61 12.19 11.78 13.1 13 12.91 12.81 2.25 16.04 15.54 15.04 14.54 16.07 15.97 15.88 15.78
2.12 15.2 14.79 14.37 13.95 15.59 15.49 15.4 15.3
2.38 17.15 16.74 16.32 15.9 17.82 17.73 17.63 17.53
2.60 18.81 18.39 17.97 17.56 19.71 19.62 19.52 19.42
2.77 20.08 19.66 19.25 18.83 21.17 21.08 20.98 20.88
2.90 21.06 20.64 20.22 19.81 22.29 22.19 22.1 22
2.97 21.58 21.16 20.75 20.33 22.89 22.8 22.7 22.6
3.00 21.81 21.39 20.97 20.56 23.15 23.05 22.96 22.86
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 57
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 4-5 Lobe 6.0 Stage HR SERIES 2
58 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 4-5 Lobe 6.0 STAGE HR SERIES 2
B 300 3000
A (BIT TO BEND) (4067)
(7481)
1085
(BIT TO 250 GPM (946 LPM)
STAB.)
250 2500
(3390)
2441
(3310)
200 2000
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
Bit Box Connection 3-1/2 REGULAR 150 1500
70%
229350 lbf 102020 daN RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 546000 lbf 243000 daN (1379) (2578) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 4-5 Lobe 6.0 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 1.05 rev/gal 0.28 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,085 psi 7,481 kPa 100 379 65 - 105
C = Overall Length 295.3 in 7501 mm Max Torque @ No Load 2,441 ft-lbs 3,310 Nm 175 662 148 - 184
Weight 1059 lbs 480.4 kg Max Power 107 HP 80 kW 250 946 230 - 263
ADJUSTABLE BUILD RATE: 5 in (127 mm) 4-5 Lobe 6.0 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 4-5 Lobe 6.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.21 1.8 1.38 0.96 0.72 0.74 0.84 0.94 1.25 8.53 8.03 7.53 7.03 7.76 7.67 7.57 7.47
0.78 5.14 4.73 4.31 3.89 4.07 3.98 3.88 3.78 1.50 10.41 9.91 9.41 8.91 9.84 9.74 9.65 9.55
1.15 7.92 7.5 7.09 6.67 7.25 7.16 7.06 6.96 1.75 12.28 11.79 11.29 10.79 11.92 11.82 11.72 11.63
1.50 10.55 10.13 9.72 9.3 10.26 10.17 10.07 9.97 2.00 14.16 13.66 13.16 12.67 14 13.9 13.8 13.7
1.83 13.03 12.61 12.19 11.78 13.1 13 12.91 12.81 2.25 16.04 15.54 15.04 14.54 16.07 15.97 15.88 15.78
2.12 15.2 14.79 14.37 13.95 15.59 15.49 15.4 15.3
2.38 17.15 16.74 16.32 15.9 17.82 17.73 17.63 17.53
2.60 18.81 18.39 17.97 17.56 19.71 19.62 19.52 19.42
2.77 20.08 19.66 19.25 18.83 21.17 21.08 20.98 20.88
2.90 21.06 20.64 20.22 19.81 22.29 22.19 22.1 22
2.97 21.58 21.16 20.75 20.33 22.89 22.8 22.7 22.6
3.00 21.81 21.39 20.97 20.56 23.15 23.05 22.96 22.86
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 59
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 5-6 Lobe 4.0 Stage SERIES 2
60 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 5-6 4.0 STAGE SERIES 2
B 300 1500
A (BIT TO BEND) (2034)
(2855)
(BIT TO
414
STAB.) 250 GPM (946 LPM)
250 1250
(1695)
1104
(1497)
200 1000
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
150 750
Bit Box Connection 3-1/2 REGULAR
70%
229350 lbf 102020 daN TO
RQ
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.62 2.12 1.63 1.14 0.83 0.87 1.01 1.15 1.25 10.09 9.5 8.91 8.32 9.3 9.17 9.03 8.89
0.78 6.08 5.59 5.1 4.6 4.9 4.76 4.62 4.49 1.50 12.31 11.72 11.13 10.54 11.81 11.67 11.53 11.4
1.15 9.37 8.88 8.39 7.89 8.76 8.62 8.48 8.34 1.75 14.54 13.95 13.36 12.77 14.31 14.18 14.04 13.9
1.50 12.48 11.99 11.5 11 12.41 12.27 12.13 11.99 2.00 16.76 16.17 15.58 14.99 16.82 16.68 16.54 16.4
1.83 15.41 14.92 14.43 13.93 15.85 15.71 15.57 15.43 2.25 18.98 18.39 17.8 17.21 19.32 19.18 19.05 18.91
2.12 17.99 17.5 17 16.51 18.87 18.73 18.59 18.46
2.38 20.3 19.8 19.31 18.82 21.58 21.44 21.3 21.17
2.60 22.25 21.76 21.26 20.77 23.87 23.73 23.6 23.46
2.77 23.76 23.27 22.77 22.28 25.64 25.51 25.37 25.23
2.90 24.91 24.42 23.93 23.43 27 26.86 26.72 26.58
2.97 25.54 25.04 24.55 24.06 27.73 27.59 27.45 27.31
3.00 25.8 25.31 24.82 24.32 28.04 27.9 27.76 27.63
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 61
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 5-6 Lobe 4.0 Stage HR SERIES 2
62 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 5-6 4.0 STAGE HR SERIES 2
B 300 2000
A (BIT TO BEND) (2712)
(BIT TO 250 GPM (946 LPM)
STAB.)
250 1656
(2245)
1500
(2034)
200
(4282)
621
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
150 1000
Bit Box Connection 3-1/2 REGULAR
70%
RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400 500 600 700
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 5-6 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 1.03 rev/gal 0.27 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 621 psi 4,282 kPa 100 379 70 - 103
C = Overall Length 248.3 in 6307 mm Max Torque @ No Load 1,656 ft-lbs 2,245 Nm 175 662 148 - 181
Weight 993 lbs 450.4 kg Max Power 71 HP 53 kW 250 946 225 - 258
ADJUSTABLE BUILD RATE: 5 in (127 mm) 5-6 Lobe 4.0 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 5-6 Lobe 4.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.62 2.12 1.63 1.14 0.83 0.87 1.01 1.15 1.25 10.09 9.5 8.91 8.32 9.3 9.17 9.03 8.89
0.78 6.08 5.59 5.1 4.6 4.9 4.76 4.62 4.49 1.50 12.31 11.72 11.13 10.54 11.81 11.67 11.53 11.4
1.15 9.37 8.88 8.39 7.89 8.76 8.62 8.48 8.34 1.75 14.54 13.95 13.36 12.77 14.31 14.18 14.04 13.9
1.50 12.48 11.99 11.5 11 12.41 12.27 12.13 11.99 2.00 16.76 16.17 15.58 14.99 16.82 16.68 16.54 16.4
1.83 15.41 14.92 14.43 13.93 15.85 15.71 15.57 15.43 2.25 18.98 18.39 17.8 17.21 19.32 19.18 19.05 18.91
2.12 17.99 17.5 17 16.51 18.87 18.73 18.59 18.46
2.38 20.3 19.8 19.31 18.82 21.58 21.44 21.3 21.17
2.60 22.25 21.76 21.26 20.77 23.87 23.73 23.6 23.46
2.77 23.76 23.27 22.77 22.28 25.64 25.51 25.37 25.23
2.90 24.91 24.42 23.93 23.43 27 26.86 26.72 26.58
2.97 25.54 25.04 24.55 24.06 27.73 27.59 27.45 27.31
3.00 25.8 25.31 24.82 24.32 28.04 27.9 27.76 27.63
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 63
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 5-6 Lobe 6.7 Stage HR SERIES 2
64 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 300
5 in (127 mm) 5-6 6.7 STAGE HR SERIES 2 8000
B (10847)
A (BIT TO BEND)
(BIT TO
STAB.) 7000
350 GPM (1325 LPM)
250 (9491)
6330
6000 (8582)
(10894)
1580
(8135)
200
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
4000
150
Bit Box Connection 3-1/2 REGULAR (5423)
70%
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11031)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 5-6 Lobe 6.7 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.63 rev/gal 0.17 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,580 psi 10,894 kPa 150 568 71 - 90
C = Overall Length 358.3 in 9101 mm Max Torque @ No Load 6,330 ft-lbs 8,582 Nm 275 1,041 148 - 170
Weight 1355 lbs 614.6 kg Max Power 271 HP 202 kW 400 1,514 225 - 250
ADJUSTABLE BUILD RATE: 5 in (127 mm) 5-6 Lobe 6.7 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 5-6 Lobe 6.7 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.83 1.49 1.14 0.80 0.61 0.62 0.69 0.75 1.25 7.06 6.65 6.24 5.83 6.35 6.29 6.22 6.16
0.78 4.26 3.91 3.57 3.22 3.32 3.26 3.19 3.13 1.50 8.62 8.21 7.79 7.38 8.04 7.98 7.91 7.85
1.15 6.56 6.21 5.87 5.52 5.90 5.83 5.76 5.70 1.75 10.17 9.76 9.35 8.93 9.73 9.67 9.60 9.54
1.50 8.74 8.39 8.05 7.70 8.33 8.26 8.20 8.13 2.00 11.73 11.31 10.90 10.49 11.42 11.36 11.29 11.23
1.83 10.79 10.44 10.10 9.75 10.62 10.56 10.49 10.43 2.25 13.28 12.87 12.46 12.04 13.11 13.05 12.98 12.92
2.12 12.59 12.25 11.90 11.55 12.64 12.58 12.51 12.44 2.50 14.84 14.42 14.01 13.60 14.80 14.74 14.67 14.61
2.38 14.21 13.86 13.52 13.17 14.45 14.38 14.32 14.25
2.60 15.57 15.23 14.88 14.54 15.98 15.91 15.85 15.78
2.77 16.63 16.28 15.94 15.59 17.16 17.09 17.03 16.96
2.90 17.44 17.09 16.75 16.40 18.06 18.00 17.93 17.87
2.97 17.87 17.53 17.18 16.84 18.55 18.48 18.42 18.35
3.00 18.06 17.71 17.37 17.02 18.76 18.69 18.63 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 65
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 5-6 Lobe 8.3 Stage HR SERIES 2
66 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 5-6 8.3 STAGE HR SERIES 2
B 330
A (BIT TO BEND) 300 GPM (1136 LPM) 5500
(13514)
(BIT TO
1960
STAB.)
300 (7457)
270
4980
(6752) 4400
240 (5966)
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm 3300
180 (4474)
Bit Box Connection 3-1/2 REGULAR
150
Dynamic 71500 lbf 31800 daN 2200
120
Bearing Load On Bottom 100 GPM (379 LPM) (2983)
Static 229350 lbf 102020 daN 90
Dynamic 71500 lbf 31800 daN 60
1100
Bearing Load - Off Bottom UE (1491)
Static RQ
229350 lbf 102020 daN TO
70%
30
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.87 1.52 1.17 0.81 0.62 0.63 0.70 0.77 1.25 7.21 6.79 6.37 5.95 6.49 6.43 6.36 6.29
0.78 4.35 3.99 3.64 3.29 3.40 3.33 3.26 3.19 1.50 8.80 8.38 7.96 7.53 8.22 8.15 8.09 8.02
1.15 6.70 6.34 5.99 5.64 6.03 5.96 5.89 5.83 1.75 10.39 9.96 9.54 9.12 9.95 9.88 9.81 9.75
1.50 8.92 8.57 8.21 7.86 8.52 8.45 8.38 8.32 2.00 11.97 11.55 11.13 10.71 11.68 11.61 11.54 11.47
1.83 11.01 10.66 10.31 9.96 10.87 10.80 10.73 10.66 2.25 13.56 13.14 12.72 12.29 13.41 13.34 13.27 13.20
2.12 12.85 12.50 12.15 11.80 12.93 12.86 12.80 12.73 2.50 15.15 14.72 14.30 13.88 15.13 15.07 15.00 14.93
2.38 14.50 14.15 13.80 13.45 14.78 14.71 14.65 14.58
2.60 15.90 15.55 15.19 14.84 16.35 16.28 16.21 16.14
2.77 16.98 16.62 16.27 15.92 17.56 17.49 17.42 17.35
2.90 17.80 17.45 17.10 16.74 18.48 18.41 18.34 18.28
2.97 18.25 17.89 17.54 17.19 18.98 18.91 18.84 18.77
3.00 18.44 18.08 17.73 17.38 19.19 19.12 19.05 18.99
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 67
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 6-7 Lobe 6.0 Stage HR SERIES 2
68 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 6-7 6.0 STAGE HR SERIES 2
B 300 5000
A (BIT TO BEND) (6779)
(BIT TO
STAB.) 4233
350 GPM (1325 LPM) (5739)
250
(10377)
4000
1505
(5423)
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm (4067)
Bit Box Connection 3-1/2 REGULAR 150
150 GPM (570 LPM)
70%
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5515) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 6-7 Lobe 6.0 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.84 rev/gal 0.22 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,505 psi 10,377 kPa 150 568 80 - 126
C = Overall Length 293.3 in 7450 mm Max Torque @ No Load 4,233 ft-lbs 5,739 Nm 225 852 143 - 189
Weight 1127 lbs 511.2 kg Max Power 165 HP 123 kW 300 1,136 205 - 252
ADJUSTABLE BUILD RATE: 5 in (127 mm) 6-7 Lobe 6.0 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 6-7 Lobe 6.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.23 1.81 1.39 0.97 0.73 0.75 0.85 0.95 1.25 8.59 8.09 7.58 7.08 7.82 7.72 7.62 7.52
0.78 5.18 4.76 4.34 3.92 4.1 4.01 3.91 3.81 1.50 10.48 9.98 9.47 8.97 9.91 9.81 9.72 9.62
1.15 7.97 7.55 7.13 6.71 7.31 7.21 7.11 7.01 1.75 12.37 11.86 11.36 10.86 12 11.91 11.81 11.71
1.50 10.62 10.2 9.78 9.36 10.34 10.24 10.14 10.04 2.00 14.26 13.75 13.25 12.75 14.1 14 13.9 13.8
1.83 13.11 12.69 12.27 11.85 13.2 13.1 13 12.9 2.25 16.14 15.64 15.14 14.64 16.19 16.09 15.99 15.89
2.12 15.3 14.88 14.47 14.05 15.71 15.61 15.51 15.41
2.38 17.27 16.85 16.43 16.01 17.96 17.86 17.76 17.66
2.60 18.93 18.51 18.09 17.67 19.86 19.76 19.67 19.57
2.77 20.21 19.79 19.38 18.96 21.33 21.24 21.14 21.04
2.90 21.2 20.78 20.36 19.94 22.46 22.36 22.26 22.16
2.97 21.72 21.31 20.89 20.47 23.06 22.97 22.87 22.77
3.00 21.95 21.53 21.11 20.69 23.32 23.23 23.13 23.03
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 69
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 6-7 Lobe 8.0 Stage HR SERIES 2
70 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 6-7 8.0 STAGE HR SERIES 2
B 350 8000
A (10846)
(14238)
(BIT TO BEND)
2065
(BIT TO
STAB.) 350 GPM (1325 LPM) 7000
300
(9491)
6000
250 (8135)
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm 200 (6779)
70%
(1356)
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 500 1000 1500 2000 2500
Absolute Overpull 546000 lbf 243000 daN (3448) (6895) (10343) (13790) (17238)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 6-7 Lobe 8.0 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.84 rev/gal 0.22 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 2,065 psi 14,238 kPa 150 568 80 - 126
C = Overall Length 358.3 in 9101 mm Max Torque @ No Load 5,897 ft-lbs 7,995 Nm 250 946 163 - 210
Weight 1353 lbs 613.7 kg Max Power 275 HP 205 kW 350 1,325 245 - 294
ADJUSTABLE BUILD RATE: 5 in (127 mm) 6-7 Lobe 8.0 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 6-7 Lobe 8.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.83 1.49 1.14 0.8 0.61 0.62 0.69 0.75 1.25 7.06 6.65 6.24 5.83 6.35 6.29 6.22 6.16
0.78 4.26 3.91 3.57 3.22 3.32 3.26 3.19 3.13 1.50 8.62 8.21 7.79 7.38 8.04 7.98 7.91 7.85
1.15 6.56 6.21 5.87 5.52 5.9 5.83 5.76 5.7 1.75 10.17 9.76 9.35 8.93 9.73 9.67 9.6 9.54
1.50 8.74 8.39 8.05 7.7 8.33 8.26 8.2 8.13 2.00 11.73 11.31 10.9 10.49 11.42 11.36 11.29 11.23
1.83 10.79 10.44 10.1 9.75 10.62 10.56 10.49 10.43 2.25 13.28 12.87 12.46 12.04 13.11 13.05 12.98 12.92
2.12 12.59 12.25 11.9 11.55 12.64 12.58 12.51 12.44
2.38 14.21 13.86 13.52 13.17 14.45 14.38 14.32 14.25
2.60 15.57 15.23 14.88 14.54 15.98 15.91 15.85 15.78
2.77 16.63 16.28 15.94 15.59 17.16 17.09 17.03 16.96
2.90 17.44 17.09 16.75 16.4 18.06 18 17.93 17.87
2.97 17.87 17.53 17.18 16.84 18.55 18.48 18.42 18.35
3.00 18.06 17.71 17.37 17.02 18.76 18.69 18.63 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 71
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 2.0 Stage SERIES 2
72 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 2.0 STAGE SERIES 2
B 100 3000
A (BIT TO BEND) (4068)
(BIT TO
STAB.) 250 GPM (945 LPM)
(2579)
374
2500
(3390)
75
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
Bit Box Connection 3-1/2 REGULAR 50 1500
70%
Static 229350 lbf 102020 daN UE (678)
RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 546000 lbf 243000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 2.0 Stage Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.30 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 374 psi 2,579 kPa 100 379 26 - 29
C = Overall Length 358.3 in 9101 mm Max Torque @ No Load 2,781 ft-lbs 3,771 Nm 175 662 52 - 49
Weight 1288 lbs 584.2 kg Max Power 41 HP 30 kW 250 946 77 - 69
ADJUSTABLE BUILD RATE: 5 in (127 mm) 7-8 Lobe 2.0 Stage SERIES 2 FBH BUILD RATE: 5 in (127 mm) 7-8 Lobe 2.0 Stage SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.83 1.49 1.14 0.8 0.61 0.62 0.69 0.75 1.25 7.06 6.65 6.24 5.83 6.35 6.29 6.22 6.16
0.78 4.26 3.91 3.57 3.22 3.32 3.26 3.19 3.13 1.50 8.62 8.21 7.79 7.38 8.04 7.98 7.91 7.85
1.15 6.56 6.21 5.87 5.52 5.9 5.83 5.76 5.7 1.75 10.17 9.76 9.35 8.93 9.73 9.67 9.6 9.54
1.50 8.74 8.39 8.05 7.7 8.33 8.26 8.2 8.13 2.00 11.73 11.31 10.9 10.49 11.42 11.36 11.29 11.23
1.83 10.79 10.44 10.1 9.75 10.62 10.56 10.49 10.43 2.25 13.28 12.87 12.46 12.04 13.11 13.05 12.98 12.92
2.12 12.59 12.25 11.9 11.55 12.64 12.58 12.51 12.44
2.38 14.21 13.86 13.52 13.17 14.45 14.38 14.32 14.25
2.60 15.57 15.23 14.88 14.54 15.98 15.91 15.85 15.78
2.77 16.63 16.28 15.94 15.59 17.16 17.09 17.03 16.96
2.90 17.44 17.09 16.75 16.4 18.06 18 17.93 17.87
2.97 17.87 17.53 17.18 16.84 18.55 18.48 18.42 18.35
3.00 18.06 17.71 17.37 17.02 18.76 18.69 18.63 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 73
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 2.6 Stage HR NP SERIES 2
74 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 2.6 STAGE HR NP SERIES 2
B 100 4000
A (BIT TO BEND) (5423)
(BIT TO
STAB.)
3500
300 GPM (1136 LPM) (4745)
(2069)
300
75 3000
(4068)
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
2000
Bit Box Connection 3-1/2 REGULAR 50
70%
UE
Static 229350 lbf 102020 daN RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 2.6 Stage HR NP Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.27 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 305 psi 2,103 kPa 150 568 29 - 40
C = Overall Length 302 in 7671 mm Max Torque @ No Load 3,500 ft-lbs 4,745 Nm 225 852 49 - 60
Weight 1165 lbs 528.4 kg Max Power 45 HP 34 kW 300 1,136 68 - 80
ADJUSTABLE BUILD RATE: 5 in (127 mm) 7-8 Lobe 2.6 Stage HR NP SERIES 2 FBH BUILD RATE: 5 in (127 mm) 7-8 Lobe 2.6 Stage HR NP SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.16 1.76 1.35 0.94 0.71 0.73 0.82 0.91 1.25 8.35 7.86 7.37 6.88 7.58 7.49 7.4 7.31
0.78 5.03 4.62 4.22 3.81 3.98 3.89 3.79 3.7 1.50 10.18 9.7 9.21 8.72 9.61 9.52 9.43 9.34
1.15 7.75 7.34 6.93 6.53 7.08 6.99 6.9 6.8 1.75 12.02 11.53 11.04 10.56 11.64 11.55 11.46 11.36
1.50 10.32 9.91 9.51 9.1 10.02 9.92 9.83 9.74 2.00 13.86 13.37 12.88 12.39 13.67 13.58 13.48 13.39
1.83 12.74 12.34 11.93 11.52 12.78 12.69 12.6 12.51 2.25 15.69 15.2 14.72 14.23 15.7 15.6 15.51 15.42
2.12 14.87 14.47 14.06 13.65 15.21 15.12 15.03 14.94
2.38 16.78 16.38 15.97 15.56 17.39 17.3 17.21 17.12
2.60 18.4 17.99 17.58 17.18 19.24 19.14 19.05 18.96
2.77 19.65 19.24 18.83 18.42 20.66 20.57 20.48 20.38
2.90 20.6 20.19 19.79 19.38 21.75 21.66 21.57 21.47
2.97 21.12 20.71 20.3 19.89 22.34 22.24 22.15 22.06
3.00 21.34 20.93 20.52 20.11 22.59 22.5 22.4 22.31
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 75
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 2.6 Stage HR SERIES 2
76 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 2.6 STAGE HR SERIES 2
B 100 7000
A (BIT TO BEND) (9491)
(BIT TO
(800)
590
STAB.)
6000
300 GPM (1136 LPM) (8135) 5250
80
(7118)
5000
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm 60
4000
(5423)
Bit Box Connection 3-1/2 REGULAR
150 GPM (568 LPM) 3000
Dynamic 71500 lbf 31800 daN 40 (4068)
Bearing Load On Bottom
Static 229350 lbf 102020 daN
70%
Static 229350 lbf 102020 daN RQ
TO (1356)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.94 1.58 1.21 0.84 0.64 0.66 0.73 0.8 1.25 7.49 7.05 6.61 6.17 6.76 6.68 6.61 6.54
0.78 4.51 4.15 3.78 3.42 3.54 3.46 3.39 3.32 1.50 9.13 8.7 8.26 7.82 8.56 8.48 8.41 8.34
1.15 6.95 6.59 6.22 5.85 6.28 6.21 6.14 6.06 1.75 10.78 10.34 9.91 9.47 10.36 10.28 10.21 10.14
1.50 9.26 8.89 8.53 8.16 8.88 8.81 8.73 8.66 2.00 12.43 11.99 11.55 11.12 12.16 12.08 12.01 11.94
1.83 11.43 11.07 10.7 10.34 11.33 11.25 11.18 11.11 2.25 14.08 13.64 13.2 12.76 13.96 13.88 13.81 13.74
2.12 13.34 12.98 12.61 12.25 13.48 13.41 13.33 13.26
2.38 15.06 14.69 14.33 13.96 15.41 15.33 15.26 15.19
2.60 16.51 16.14 15.77 15.41 17.04 16.97 16.89 16.82
2.77 17.62 17.26 16.89 16.53 18.3 18.23 18.15 18.08
2.90 18.48 18.12 17.75 17.38 19.26 19.19 19.12 19.04
2.97 18.94 18.58 18.21 17.84 19.78 19.71 19.64 19.56
3.00 19.14 18.77 18.41 18.04 20 19.93 19.86 19.78
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 77
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 3.7 Stage HR SERIES 2
78 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 3.7 STAGE HR SERIES 2
B 120 8000
A (BIT TO BEND) (10846)
(BIT TO 350 GPM (1325 LPM)
7124
STAB.)
7000 (9659)
100 (9491)
(7481)
1085
6000
(8135)
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm (6779)
70%
2000
Dynamic 71500 lbf 31800 daN (2712)
Bearing Load - Off Bottom 20
Static 229350 lbf 102020 daN UE 1000
RQ (1356)
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 3.7 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.31 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,085 psi 7,481 kPa 100 379 10 - 31
C = Overall Length 343.3 in 8720 mm Max Torque @ No Load 7,124 ft-lbs 9,659 Nm 225 852 49 - 70
Weight 1335 lbs 605.5 kg Max Power 119 HP 89 kW 350 1,325 88 - 109
ADJUSTABLE BUILD RATE: 5 in (127 mm) 7-8 Lobe 3.7 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 7-8 Lobe 3.7 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.91 1.55 1.19 0.83 0.63 0.65 0.72 0.79 1.25 7.37 6.94 6.5 6.07 6.64 6.57 6.5 6.43
0.78 4.44 4.08 3.72 3.36 3.47 3.4 3.33 3.26 1.50 8.99 8.56 8.13 7.7 8.41 8.34 8.27 8.2
1.15 6.84 6.48 6.12 5.76 6.17 6.1 6.03 5.96 1.75 10.61 10.18 9.75 9.32 10.18 10.11 10.04 9.96
1.50 9.11 8.75 8.39 8.03 8.72 8.65 8.58 8.51 2.00 12.23 11.8 11.37 10.94 11.95 11.87 11.8 11.73
1.83 11.25 10.89 10.53 10.17 11.13 11.05 10.98 10.91 2.25 13.85 13.42 12.99 12.56 13.71 13.64 13.57 13.5
2.12 13.13 12.77 12.41 12.05 13.24 13.17 13.09 13.02
2.38 14.81 14.45 14.09 13.73 15.13 15.06 14.99 14.92
2.60 16.24 15.88 15.52 15.16 16.73 16.66 16.59 16.52
2.77 17.34 16.98 16.62 16.26 17.97 17.9 17.83 17.76
2.90 18.18 17.82 17.46 17.1 18.92 18.85 18.77 18.7
2.97 18.63 18.27 17.92 17.56 19.43 19.36 19.28 19.21
3.00 18.83 18.47 18.11 17.75 19.64 19.57 19.5 19.43
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 79
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 3.8 Stage HR SERIES 2
80 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 3.8 STAGE HR SERIES 2
B 140 6000
A (BIT TO BEND) 250 GPM (946 LPM) (8135)
(BIT TO 4965
STAB.)
(6732)
120 5000
(7481)
1085
(6779)
100
175 GPM (663 LPM) 4000
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm 80
70%
RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 3.8 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.52 rev/gal 0.14 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,085 psi 7,481 kPa 100 379 42 - 52
C = Overall Length 295.3 in 7501 mm Max Torque @ No Load 4,965 ft-lbs 6,732 Nm 175 662 82 - 91
Weight 1094 lbs 496.2 kg Max Power 115 HP 89 kW 250 946 122 - 130
ADJUSTABLE BUILD RATE: 5 in (127 mm) 7-8 Lobe 3.8 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 7-8 Lobe 3.8 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.21 1.8 1.38 0.96 0.72 0.74 0.84 0.94 1.25 8.53 8.03 7.53 7.03 7.76 7.67 7.57 7.47
0.78 5.14 4.73 4.31 3.89 4.07 3.98 3.88 3.78 1.50 10.41 9.91 9.41 8.91 9.84 9.74 9.65 9.55
1.15 7.92 7.5 7.09 6.67 7.25 7.16 7.06 6.96 1.75 12.28 11.79 11.29 10.79 11.92 11.82 11.72 11.63
1.50 10.55 10.13 9.72 9.3 10.26 10.17 10.07 9.97 2.00 14.16 13.66 13.16 12.67 14 13.9 13.8 13.7
1.83 13.03 12.61 12.19 11.78 13.1 13 12.91 12.81 2.25 16.04 15.54 15.04 14.54 16.07 15.97 15.88 15.78
2.12 15.2 14.79 14.37 13.95 15.59 15.49 15.4 15.3
2.38 17.15 16.74 16.32 15.9 17.82 17.73 17.63 17.53
2.60 18.81 18.39 17.97 17.56 19.71 19.62 19.52 19.42
2.77 20.08 19.66 19.25 18.83 21.17 21.08 20.98 20.88
2.90 21.06 20.64 20.22 19.81 22.29 22.19 22.1 22
2.97 21.58 21.16 20.75 20.33 22.89 22.8 22.7 22.6
3.00 21.81 21.39 20.97 20.56 23.15 23.05 22.96 22.86
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 81
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 4.5 Stage HR SERIES 2
82 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 4.5 STAGE HR SERIES 2
B
A (BIT TO BEND) 6000
(BIT TO 160
STAB.) (8135)
300 GPM (1136 LPM) 5250
(7120)
5000
(6964)
1010
(6779)
120
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm (5423)
70%
UE
Static 229350 lbf 102020 daN RQ (1356)
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 4.5 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.46 rev/gal 0.12 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,010 psi 6,964 kPa 150 568 50 - 69
C = Overall Length 337.6 in 8575 mm Max Torque @ No Load 5,250 ft-lbs 7,118 Nm 225 852 86 - 105
Weight 1326 lbs 601.5 kg Max Power 121 HP 90 kW 300 1,136 121 - 140
ADJUSTABLE BUILD RATE: 5 in (127 mm) 7-8 Lobe 4.5 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 7-8 Lobe 4.5 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.94 1.58 1.21 0.84 0.64 0.66 0.73 0.8 1.25 7.49 7.05 6.61 6.17 6.76 6.68 6.61 6.54
0.78 4.51 4.15 3.78 3.42 3.54 3.46 3.39 3.32 1.50 9.13 8.7 8.26 7.82 8.56 8.48 8.41 8.34
1.15 6.95 6.59 6.22 5.85 6.28 6.21 6.14 6.06 1.75 10.78 10.34 9.91 9.47 10.36 10.28 10.21 10.14
1.50 9.26 8.89 8.53 8.16 8.88 8.81 8.73 8.66 2.00 12.43 11.99 11.55 11.12 12.16 12.08 12.01 11.94
1.83 11.43 11.07 10.7 10.34 11.33 11.25 11.18 11.11 2.25 14.08 13.64 13.2 12.76 13.96 13.88 13.81 13.74
2.12 13.34 12.98 12.61 12.25 13.48 13.41 13.33 13.26
2.38 15.06 14.69 14.33 13.96 15.41 15.33 15.26 15.19
2.60 16.51 16.14 15.77 15.41 17.04 16.97 16.89 16.82
2.77 17.62 17.26 16.89 16.53 18.3 18.23 18.15 18.08
2.90 18.48 18.12 17.75 17.38 19.26 19.19 19.12 19.04
2.97 18.94 18.58 18.21 17.84 19.78 19.71 19.64 19.56
3.00 19.14 18.77 18.41 18.04 20 19.93 19.86 19.78
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 83
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 7-8 Lobe 5.0 Stage HR SERIES 2
84 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 7-8 5.0 STAGE HR SERIES 2
B 250 7000
A (BIT TO BEND) (9491)
(8136)
(BIT TO
1180
STAB.)
6000
300 GPM (1136 LPM) (8135) 4670
200
(7118)
5000
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm 150
4000
(5423)
Bit Box Connection 3-1/2 REGULAR
150 GPM (568 LPM) 3000
Dynamic 71500 lbf 31800 daN 100 (4068)
Bearing Load On Bottom
Static 229350 lbf 102020 daN
70%
Static 229350 lbf 102020 daN RQ
UE (1356)
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 12000 ft-lbs 16270 Nm
A = Bit To Stabilizer (center) 16.7 in 424 mm
Lobe Configuration 7-8 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 56.3 in 1430 mm
B = Bit to Bend Displacement 0.62 rev/gal 0.16 rev/l GPM LPM RPM
Fixed 45.7 in 1161 mm
Max Differential @ No Load 1,180 psi 8,136 kPa 150 568 72 - 93
C = Overall Length 306.3 in 7780 mm Max Torque @ No Load 4,670 ft-lbs 6,332 Nm 225 852 119 - 140
Weight 1283 lbs 582 kg Max Power 147 HP 109 kW 300 1,136 165 - 186
ADJUSTABLE BUILD RATE: 5 in (127 mm) 7-8 Lobe 5.0 Stage HR SERIES 2 FBH BUILD RATE: 5 in (127 mm) 7-8 Lobe 5.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4 Size 5-7/8 6 6-1/8 6-1/4 5-7/8 6 6-1/8 6-1/4
(149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm) (149 mm) (152 mm) (156 mm) (159 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.14 1.73 1.33 0.93 0.70 0.72 0.81 0.90 1.25 8.23 7.75 7.27 6.79 7.47 7.38 7.29 7.20
0.78 4.96 4.56 4.16 3.76 3.92 3.83 3.74 3.65 1.50 10.04 9.56 9.08 8.60 9.47 9.38 9.29 9.20
1.15 7.64 7.24 6.84 6.44 6.97 6.88 6.79 6.70 1.75 11.86 11.37 10.89 10.41 11.47 11.38 11.29 11.20
1.50 10.18 9.78 9.38 8.97 9.86 9.77 9.68 9.59 2.00 13.67 13.19 12.70 12.22 13.47 13.38 13.29 13.20
1.83 12.57 12.17 11.77 11.36 12.59 12.50 12.41 12.32 2.25 15.48 15.00 14.52 14.03 15.46 15.37 15.28 15.19
2.12 14.67 14.27 13.87 13.47 14.98 14.89 14.80 14.71 2.50 17.29 16.81 16.33 15.84 17.46 17.37 17.28 17.19
2.38 16.55 16.15 15.75 15.35 17.13 17.04 16.95 16.86
2.60 18.15 17.75 17.34 16.94 18.94 18.85 18.76 18.67
2.77 19.38 18.98 18.57 18.17 20.34 20.25 20.16 20.07
2.90 20.32 19.92 19.52 19.11 21.42 21.33 21.24 21.15
2.97 20.83 20.42 20.02 19.62 21.99 21.90 21.81 21.72
3.00 21.04 20.64 20.24 19.84 22.24 22.15 22.06 21.97
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 85
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
5 in (127 mm) 8-9 Lobe 6.0 Stage HR SERIES 2
86 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 5 in (127 mm) 8-9 6.0 STAGE HR SERIES 2 8174
B 160 (11082)
(9722)
1410
A (BIT TO BEND)
(BIT TO 280 GPM (1060 LPM)
STAB.) 7150
140 (9694)
6910
6130 (9369)
120
220 GPM (833 LPM) (8311)
SPEED (RPM)
Bit Size Range 5-5/8 - 6-3/4 in 143 - 171 mm
4085
Bit Box Connection 3-1/2 REGULAR 80 150 GPM (568 LPM) (5539)
70%
Static 20
229350 lbf 102020 daN TO
RQ (1383)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.83 1.49 1.14 0.80 0.61 0.62 0.69 0.75 1.25 7.06 6.65 6.24 5.83 6.35 6.29 6.22 6.16
0.78 4.26 3.91 3.57 3.22 3.32 3.26 3.19 3.13 1.50 8.62 8.21 7.79 7.38 8.04 7.98 7.91 7.85
1.15 6.56 6.21 5.87 5.52 5.90 5.83 5.76 5.70 1.75 10.17 9.76 9.35 8.93 9.73 9.67 9.60 9.54
1.50 8.74 8.39 8.05 7.70 8.33 8.26 8.20 8.13 2.00 11.73 11.31 10.90 10.49 11.42 11.36 11.29 11.23
1.83 10.79 10.44 10.10 9.75 10.62 10.56 10.49 10.43 2.25 13.28 12.87 12.46 12.04 13.11 13.05 12.98 12.92
2.12 12.59 12.25 11.90 11.55 12.64 12.58 12.51 12.44 2.50 14.84 14.42 14.01 13.60 14.80 14.74 14.67 14.61
2.38 14.21 13.86 13.52 13.17 14.45 14.38 14.32 14.25
2.60 15.57 15.23 14.88 14.54 15.98 15.91 15.85 15.78
2.77 16.63 16.28 15.94 15.59 17.16 17.09 17.03 16.96
2.90 17.44 17.09 16.75 16.40 18.06 18.00 17.93 17.87
2.97 17.87 17.53 17.18 16.84 18.55 18.48 18.42 18.35
3.00 18.06 17.71 17.37 17.02 18.76 18.69 18.63 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 87
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 4-5 Lobe 7.0 Stage HR SERIES 1
88 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 4-5 7.0 STAGE HR SERIES 1
B 350 6000
A (BIT TO BEND) (8135)
(BIT TO 5565
STAB.) 600 GPM (2271 LPM)
300 (7545)
5000
(8688)
1260
(6779)
250
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 200
70%
Dynamic 128500 lbf 57160 daN
Bearing Load - Off Bottom UE 1000
50 RQ
Static 404500 lbf 179930 daN TO (1356)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.87 - - - 0.88 1.22 1.36 1.99 1.25 6.1 4.51 3.87 1.02 6.68 6.33 6.21 6.84
0.78 3.36 2 1.45 - 3.43 3.29 3.43 4.06 1.50 7.69 6.11 5.47 2.62 8.5 8.15 8.01 8.22
1.15 5.73 4.36 3.82 1.37 6.21 5.86 5.72 6.02 1.75 9.29 7.7 7.07 4.21 10.32 9.97 9.83 9.6
1.50 7.96 6.6 6.06 3.6 8.84 8.49 8.35 7.87 2.00 10.89 9.3 8.67 5.81 12.14 11.79 11.65 11.02
1.83 10.07 8.71 8.16 5.71 11.31 10.97 10.83 10.2 2.25 12.49 10.9 10.26 7.41 13.96 13.61 13.47 12.84
2.12 11.92 10.56 10.02 7.56 13.49 13.14 13 12.38
2.38 13.58 12.22 11.68 9.22 15.44 15.09 14.95 14.33
2.60 14.99 13.63 13.08 10.63 17.09 16.74 16.6 15.98
2.77 16.07 14.71 14.17 11.71 18.37 18.02 17.88 17.25
2.90 16.9 15.54 15 12.54 19.34 18.99 18.85 18.23
2.97 17.35 15.99 15.44 12.99 19.87 19.52 19.38 18.75
3.00 17.54 16.18 15.64 13.18 20.09 19.74 19.6 18.98
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 89
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 6-7 Lobe 5.0 Stage HR SERIES 1
90 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 6-7 5.0 STAGE HR SERIES 1
B 200
A (BIT TO BEND) 600 GPM (2271 LPM)
(BIT TO
STAB.) 180 10000
(13558)
(8688)
9762
1260
160
(13235)
450 GPM (1703 LPM) 8000
140
(10846)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm
6000
Bit Box Connection 4-1/2 REGULAR 100 300 GPM (1136 LPM) (8135)
70%
Dynamic 128500 lbf 57160 daN 40
2000
Bearing Load - Off Bottom UE
Static 404500 lbf 179930 daN 20 RQ (2712)
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.91 - - - 0.92 1.3 1.45 2.13 1.25 6.36 4.7 4.04 1.06 6.98 6.6 6.47 7.15
0.78 3.5 2.08 1.52 - 3.58 3.43 3.58 4.27 1.50 8.02 6.37 5.71 2.73 8.89 8.51 8.36 8.59
1.15 5.97 4.55 3.98 1.42 6.5 6.12 5.97 6.29 1.75 9.69 8.03 7.37 4.39 10.8 10.42 10.26 10.02
1.50 8.3 6.88 6.31 3.76 9.26 8.88 8.72 8.21 2.00 11.35 9.7 9.04 6.06 12.7 12.32 12.17 11.49
1.83 10.5 9.08 8.51 5.96 11.86 11.48 11.32 10.64 2.25 13.02 11.36 10.7 7.72 14.61 14.23 14.08 13.39
2.12 12.43 11.01 10.44 7.89 14.14 13.76 13.61 12.93
2.38 14.16 12.74 12.18 9.62 16.19 15.81 15.66 14.97
2.60 15.63 14.21 13.64 11.08 17.92 17.54 17.39 16.71
2.77 16.76 15.34 14.77 12.21 19.26 18.88 18.73 18.04
2.90 17.63 16.21 15.64 13.08 20.28 19.9 19.75 19.07
2.97 18.09 16.67 16.1 13.55 20.83 20.45 20.3 19.62
3.00 18.29 16.87 16.3 13.75 21.07 20.69 20.54 19.86
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 91
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.0 Stage HR SERIES 1
92 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 2.0 STAGE HR SERIES 1
B
A (BIT TO BEND)
(BIT TO 500 GPM (1892 LPM) 8000
STAB.) 80 (10846)
(3103)
7200
450
(9762)
375 GPM (1419 LPM) 6000
60
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm
Bit Box Connection 4-1/2 REGULAR 250 GPM (946 LPM) 4000
70%
Static RQ
404500 lbf 179930 daN TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.05 - - - 1.07 1.59 1.79 2.72 1.25 7.36 5.44 4.68 1.23 8.15 7.63 7.46 8.39
0.78 4.06 2.41 1.75 - 4.16 3.96 4.17 5.1 1.50 9.29 7.37 6.6 3.16 10.4 9.89 9.68 10
1.15 6.91 5.27 4.61 1.65 7.62 7.1 6.9 7.35 1.75 11.21 9.3 8.53 5.08 12.66 12.14 11.93 11.61
1.50 9.61 7.96 7.31 4.35 10.9 10.38 10.17 9.49 2.00 13.14 11.22 10.46 7.01 14.91 14.4 14.19 13.26
1.83 12.15 10.51 9.85 6.89 13.98 13.47 13.26 12.33 2.25 15.07 13.15 12.39 8.94 17.16 16.65 16.44 15.51
2.12 14.39 12.74 12.09 9.13 16.7 16.18 15.98 15.05
2.38 16.39 14.75 14.09 11.13 19.13 18.62 18.41 17.48
2.60 18.09 16.44 15.79 12.83 21.19 20.67 20.47 19.54
2.77 19.4 17.75 17.1 14.14 22.78 22.26 22.06 21.13
2.90 20.4 18.75 18.1 15.14 24 23.48 23.27 22.34
2.97 20.94 19.29 18.64 15.68 24.65 24.13 23.93 23
3.00 21.17 19.52 18.87 15.91 24.93 24.41 24.21 23.28
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 93
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.9 Stage HR SERIES 1
94 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 2.9 STAGE HR SERIES 1
B 120 14000
A (BIT TO BEND) (18981)
(BIT TO 12735
STAB.)
600 GPM (2271 LPM) 12000 (17266)
100
(6033)
(16270)
875
10000
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 8000
(10846)
Bit Box Connection 4-1/2 REGULAR 60
70%
(2712)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.86 - - - 0.86 1.2 1.33 1.94 1.25 6.01 4.44 3.82 1 6.58 6.24 6.12 6.73
0.78 3.31 1.97 1.43 - 3.38 3.24 3.38 3.98 1.50 7.58 6.02 5.39 2.58 8.37 8.03 7.89 8.09
1.15 5.64 4.3 3.76 1.35 6.11 5.77 5.64 5.92 1.75 9.15 7.59 6.96 4.15 10.15 9.82 9.68 9.46
1.50 7.84 6.5 5.96 3.55 8.69 8.35 8.22 7.76 2.00 10.73 9.16 8.54 5.72 11.94 11.6 11.47 10.86
1.83 9.92 8.58 8.04 5.63 11.13 10.79 10.65 10.05 2.25 12.3 10.74 10.11 7.3 13.73 13.39 13.26 12.65
2.12 11.75 10.4 9.87 7.45 13.27 12.93 12.79 12.19
2.38 13.38 12.04 11.5 9.09 15.18 14.84 14.71 14.1
2.60 14.77 13.42 12.89 10.47 16.8 16.47 16.33 15.72
2.77 15.83 14.49 13.96 11.54 18.06 17.72 17.59 16.98
2.90 16.65 15.31 14.77 12.36 19.02 18.68 18.54 17.94
2.97 17.09 15.75 15.21 12.8 19.53 19.19 19.06 18.45
3.00 17.28 15.94 15.4 12.99 19.75 19.42 19.28 18.67
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 95
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage SERIES 1
96 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.0 STAGE SERIES 1
B 200 5000
(3100)
A (BIT TO BEND) (6779)
450
(BIT TO
STAB.) 600 GPM (2271 LPM) 4190
(5670)
160 4000
(5423)
450 GPM (1703 LPM)
70%
Static 404500 lbf 179930 daN RQ
TO
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 100 200 300 400 500
Absolute Overpull 678200 lbf 302000 daN (690) (1379) (2069) (2578) (3448)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 3.0 Stage Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 450 psi 3,103 kPa 300 1,136 55 - 84
C = Overall Length 256.1 in 6505 mm Max Torque @ No Load 4,190 ft-lbs 5,681 Nm 450 1,703 99 - 127
Weight 1884 lbs 854.6 kg Max Power 113 HP 84 kW 600 2,271 142 - 170
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.16 - - - 1.2 1.84 2.09 3.24 1.25 8.14 6.02 5.17 1.36 9.07 8.44 8.24 9.39
0.78 4.49 2.67 1.94 - 4.6 4.38 4.64 5.79 1.50 10.28 8.16 7.31 3.49 11.61 10.97 10.72 11.13
1.15 7.65 5.83 5.1 1.82 8.52 7.88 7.62 8.2 1.75 12.41 10.29 9.44 5.63 14.15 13.51 13.25 12.86
1.50 10.63 8.81 8.09 4.81 12.22 11.58 11.32 10.49 2.00 14.54 12.42 11.57 7.76 16.69 16.05 15.79 14.64
1.83 13.45 11.63 10.9 7.63 15.71 15.07 14.81 13.66 2.25 16.67 14.55 13.71 9.89 19.22 18.58 18.33 17.18
2.12 15.92 14.1 13.38 10.1 18.77 18.13 17.88 16.73
2.38 18.14 16.32 15.59 12.32 21.52 20.88 20.63 19.48
2.60 20.02 18.2 17.47 14.2 23.85 23.21 22.95 21.8
2.77 21.47 19.65 18.92 15.64 25.64 25 24.75 23.6
2.90 22.58 20.76 20.03 16.75 27.01 26.38 26.12 24.97
2.97 23.17 21.35 20.62 17.35 27.75 27.12 26.86 25.71
3.00 23.43 21.61 20.88 17.61 28.07 27.43 27.18 26.03
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 97
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SERIES 1
98 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.0 STAGE HR SERIES 1
B 200
A (BIT TO BEND)
(4650)
7000
680
(BIT TO
STAB.) 600 GPM (2271 LPM) (9491)
6280
160 6000 (8510)
(8135)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 120
4000
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM)
(5423)
70%
1000
Static 404500 lbf 179930 daN RQ
TO (1356)
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 100 200 300 400 500 600 700
Absolute Overpull 678200 lbf 302000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 3.0 Stage HR Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 680 psi 4,688 kPa 300 1,136 55 - 84
C = Overall Length 256.1 in 6505 mm Max Torque @ No Load 6,280 ft-lbs 8,515 Nm 450 1,703 99 - 127
Weight 1884 lbs 854.6 kg Max Power 170 HP 127 kW 600 2,271 142 - 170
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.16 - - - 1.2 1.84 2.09 3.24 1.25 8.14 6.02 5.17 1.36 9.07 8.44 8.24 9.39
0.78 4.49 2.67 1.94 - 4.6 4.38 4.64 5.79 1.50 10.28 8.16 7.31 3.49 11.61 10.97 10.72 11.13
1.15 7.65 5.83 5.1 1.82 8.52 7.88 7.62 8.2 1.75 12.41 10.29 9.44 5.63 14.15 13.51 13.25 12.86
1.50 10.63 8.81 8.09 4.81 12.22 11.58 11.32 10.49 2.00 14.54 12.42 11.57 7.76 16.69 16.05 15.79 14.64
1.83 13.45 11.63 10.9 7.63 15.71 15.07 14.81 13.66 2.25 16.67 14.55 13.71 9.89 19.22 18.58 18.33 17.18
2.12 15.92 14.1 13.38 10.1 18.77 18.13 17.88 16.73
2.38 18.14 16.32 15.59 12.32 21.52 20.88 20.63 19.48
2.60 20.02 18.2 17.47 14.2 23.85 23.21 22.95 21.8
2.77 21.47 19.65 18.92 15.64 25.64 25 24.75 23.6
2.90 22.58 20.76 20.03 16.75 27.01 26.38 26.12 24.97
2.97 23.17 21.35 20.62 17.35 27.75 27.12 26.86 25.71
3.00 23.43 21.61 20.88 17.61 28.07 27.43 27.18 26.03
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 99
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SLOW SERIES 1
100 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.0 STAGE HR SLOW SERIES 1
B 180
A
(4688)
(BIT TO BEND)
680
(BIT TO
STAB.)
12000
600 GPM (2271 LPM) (16270)
90 10800
(14640)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm (12202)
70%
Static 404500 lbf 179930 daN UE
RQ
TO
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 100 200 300 400 500 600 700
Absolute Overpull 678200 lbf 302000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 3.0 Stage HR SLOW Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 680 psi 4,688 kPa 300 1,136 35 - 46
C = Overall Length 335.1 in 8512 mm Max Torque @ No Load 10,800 ft-lbs 14,643 Nm 450 1,703 58 - 70
Weight 2470 lbs 1120.4 kg Max Power 165 HP 123 kW 600 2,271 80 - 93
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SLOW
SLOW SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.9 - - - 0.9 1.27 1.42 2.09 1.25 6.28 4.65 3.99 1.05 6.9 6.53 6.4 7.06
0.78 3.46 2.06 1.5 - 3.54 3.39 3.54 4.21 1.50 7.93 6.29 5.64 2.7 8.78 8.41 8.26 8.48
1.15 5.9 4.5 3.94 1.41 6.42 6.05 5.9 6.21 1.75 9.58 7.94 7.29 4.34 10.66 10.29 10.14 9.9
1.50 8.21 6.8 6.24 3.71 9.14 8.77 8.62 8.11 2.00 11.22 9.59 8.93 5.99 12.54 12.17 12.02 11.36
1.83 10.38 8.98 8.41 5.89 11.7 11.33 11.18 10.52 2.25 12.87 11.23 10.58 7.63 14.42 14.05 13.91 13.24
2.12 12.29 10.88 10.32 7.8 13.96 13.59 13.44 12.77
2.38 14 12.6 12.03 9.51 15.98 15.61 15.46 14.79
2.60 15.45 14.04 13.48 10.95 17.69 17.32 17.17 16.5
2.77 16.57 15.16 14.6 12.07 19.01 18.64 18.49 17.82
2.90 17.42 16.02 15.46 12.93 20.02 19.65 19.5 18.83
2.97 17.88 16.48 15.92 13.39 20.56 20.19 20.04 19.37
3.00 18.08 16.68 16.11 13.59 20.79 20.42 20.27 19.61
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 101
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR SERIES 1
102 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.3 STAGE HR SERIES 1
B 120
A (BIT TO BEND) 16000
(BIT TO
STAB.) 600 GPM (2271 LPM) (21693)
15610
100
(6516)
14000 (21164)
945
(18981)
12000
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 10000
(13558)
Bit Box Connection 4-1/2 REGULAR 60
300 GPM (1136 LPM) 8000
70%
2000
(2712)
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 678200 lbf 302000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6206) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 3.3 Stage HR Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 945 psi 6,516 kPa 300 1,136 35 - 51
C = Overall Length 376.1 in 9553 mm Max Torque @ No Load 15,610 ft-lbs 21,164 Nm 450 1,703 60 - 77
Weight 2680 lbs 1215.6 kg Max Power 253 HP 188 kW 600 2,271 85 - 102
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR FBH BUILD RATE:6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.8 - - - 0.8 1.1 1.21 1.74 1.25 5.62 4.16 3.57 0.94 6.13 5.84 5.73 6.26
0.78 3.1 1.84 1.34 - 3.16 3.03 3.15 3.68 1.50 7.09 5.63 5.04 2.41 7.79 7.5 7.38 7.55
1.15 5.28 4.02 3.52 1.26 5.69 5.39 5.27 5.52 1.75 8.56 7.1 6.51 3.88 9.45 9.16 9.04 8.84
1.50 7.34 6.08 5.58 3.32 8.08 7.78 7.67 7.26 2.00 10.03 8.57 7.99 5.35 11.11 10.82 10.7 10.17
1.83 9.28 8.02 7.52 5.26 10.33 10.04 9.92 9.39 2.25 11.51 10.04 9.46 6.82 12.77 12.47 12.36 11.83
2.12 10.99 9.73 9.23 6.97 12.31 12.02 11.9 11.37
2.38 12.52 11.26 10.76 8.5 14.09 13.79 13.68 13.15
2.60 13.81 12.56 12.05 9.79 15.59 15.29 15.18 14.65
2.77 14.81 13.56 13.05 10.79 16.75 16.45 16.34 15.81
2.90 15.58 14.32 13.82 11.56 17.64 17.34 17.22 16.7
2.97 15.99 14.73 14.23 11.97 18.11 17.82 17.7 17.17
3.00 16.17 14.91 14.41 12.15 18.32 18.02 17.91 17.38
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 103
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR SERIES 1
104 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.5 STAGE HR SERIES 1
B 100
(5430)
A (BIT TO BEND)
790
(BIT TO
STAB.)
400 GPM (1514 LPM)
10000
80 (13558)
9840
(13350)
8000
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 60
6000
Bit Box Connection 4-1/2 REGULAR
70%
Static 404500 lbf 179930 daN UE (2712)
RQ
TO
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 100 200 300 400 500 600 700 800 900
Absolute Overpull 678200 lbf 302000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6206)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 3.5 Stage HR Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.21 rev/gal 0.05 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 790 psi 5,447 kPa 150 568 22 - 31
C = Overall Length 362.4 in 9205 mm Max Torque @ No Load 9,840 ft-lbs 13,341 Nm 275 1,041 47 - 57
Weight 2654 lbs 1203.8 kg Max Power 135 HP 101 kW 400 1,514 72 - 83
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.83 - - - 0.83 1.15 1.28 1.85 1.25 5.82 4.31 3.7 0.97 6.37 6.05 5.94 6.51
0.78 3.21 1.91 1.39 - 3.28 3.15 3.27 3.84 1.50 7.35 5.83 5.23 2.5 8.1 7.78 7.65 7.84
1.15 5.47 4.17 3.65 1.31 5.91 5.59 5.47 5.73 1.75 8.88 7.36 6.75 4.02 9.82 9.51 9.38 9.17
1.50 7.61 6.31 5.78 3.44 8.4 8.09 7.96 7.52 2.00 10.4 8.89 8.28 5.55 11.55 11.23 11.11 10.54
1.83 9.62 8.32 7.8 5.46 10.75 10.44 10.31 9.74 2.25 11.93 10.41 9.8 7.08 13.28 12.96 12.83 12.26
2.12 11.39 10.09 9.57 7.23 12.82 12.5 12.37 11.8
2.38 12.98 11.68 11.15 8.81 14.67 14.35 14.22 13.65
2.60 14.32 13.02 12.5 10.15 16.23 15.92 15.79 15.22
2.77 15.36 14.05 13.53 11.19 17.44 17.13 17 16.43
2.90 16.15 14.85 14.33 11.98 18.37 18.05 17.92 17.35
2.97 16.58 15.27 14.75 12.41 18.86 18.55 18.42 17.85
3.00 16.76 15.46 14.94 12.59 19.08 18.76 18.63 18.06
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 105
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR SERIES 1
106 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 4.8 STAGE HR SERIES 1
B 140
A (BIT TO BEND)
(BIT TO
10000
STAB.) 400 GPM (1514 LPM)
120 (13558)
9948
(13488)
(9412)
1365
100 8000
(10846)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 80
6000
Bit Box Connection 4-1/2 REGULAR (8135)
70%
Dynamic 128500 lbf 57160 daN 2000
Bearing Load - Off Bottom 20 UE (2712)
Static 404500 lbf 179930 daN RQ
TO
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 678200 lbf 302000 daN (1379) (2578) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 4.8 Stage HR Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.33 rev/gal 0.09 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 1,365 psi 9,411 kPa 200 757 51 - 66
C = Overall Length 334.6 in 8499 mm Max Torque @ No Load 9,948 ft-lbs 13,488 Nm 300 1,136 84 - 99
Weight 2325 lbs 1054.6 kg Max Power 220 HP 164 kW 400 1,514 116 - 132
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.9 - - - 0.91 1.28 1.43 2.1 1.25 6.29 4.65 4 1.05 6.91 6.54 6.41 7.08
0.78 3.47 2.06 1.5 - 3.55 3.4 3.54 4.21 1.50 7.94 6.3 5.65 2.7 8.79 8.42 8.27 8.5
1.15 5.91 4.5 3.94 1.41 6.43 6.05 5.91 6.22 1.75 9.59 7.95 7.3 4.35 10.68 10.31 10.16 9.91
1.50 8.22 6.81 6.25 3.72 9.15 8.78 8.63 8.12 2.00 11.24 9.6 8.95 6 12.56 12.19 12.04 11.37
1.83 10.39 8.99 8.43 5.89 11.72 11.35 11.2 10.53 2.25 12.89 11.25 10.59 7.64 14.45 14.08 13.93 13.26
2.12 12.31 10.9 10.34 7.81 13.98 13.61 13.46 12.79
2.38 14.02 12.61 12.05 9.52 16 15.63 15.48 14.81
2.60 15.47 14.06 13.5 10.97 17.72 17.34 17.19 16.53
2.77 16.59 15.18 14.62 12.09 19.04 18.67 18.52 17.85
2.90 17.45 16.04 15.48 12.95 20.05 19.68 19.53 18.86
2.97 17.91 16.5 15.94 13.41 20.59 20.22 20.07 19.4
3.00 18.11 16.7 16.14 13.61 20.83 20.46 20.31 19.64
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 107
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR SERIES 1
108 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 5.0 STAGE HR SERIES 1
B 180 14000
A (BIT TO BEND) 600 GPM (2271 LPM) (18981)
(BIT TO 12813
STAB.) 160
12000 (17372)
(16270)
(10377)
140
1505
450 GPM (1703 LPM)
10000
120
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 100 8000
(10846)
300 GPM (1136 LPM)
Bit Box Connection 4-1/2 REGULAR
70%
Bearing Load - Off Bottom 2000
Static 404500 lbf 179930 daN 20 UE
RQ (2712)
TO
Max. Overpull for Re-run 406900 lbf 181000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 678200 lbf 302000 daN (1379) (2578) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.3 in 414 mm
Lobe Configuration 7-8 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 73 in 1854 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 61.1 in 1552 mm
Max Differential @ No Load 1,505 psi 10,377 kPa 300 1,136 73 - 84
C = Overall Length 335.1 in 8512 mm Max Torque @ No Load 12,813 ft-lbs 17,372 Nm 450 1,703 115 - 126
Weight 2514 lbs 1140.3 kg Max Power 381 HP 284 kW 600 2,271 156 - 168
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR FBH BUILD RATE:6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR
SERIES 1 SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.9 - - - 0.9 1.27 1.42 2.09 1.25 6.28 4.65 3.99 1.05 6.9 6.53 6.4 7.06
0.78 3.46 2.06 1.5 - 3.54 3.39 3.54 4.21 1.50 7.93 6.29 5.64 2.7 8.78 8.41 8.26 8.48
1.15 5.9 4.5 3.94 1.41 6.42 6.05 5.9 6.21 1.75 9.58 7.94 7.29 4.34 10.66 10.29 10.14 9.9
1.50 8.21 6.8 6.24 3.71 9.14 8.77 8.62 8.11 2.00 11.22 9.59 8.93 5.99 12.54 12.17 12.02 11.36
1.83 10.38 8.98 8.41 5.89 11.7 11.33 11.18 10.52 2.25 12.87 11.23 10.58 7.63 14.42 14.05 13.91 13.24
2.12 12.29 10.88 10.32 7.8 13.96 13.59 13.44 12.77
2.38 14 12.6 12.03 9.51 15.98 15.61 15.46 14.79
2.60 15.45 14.04 13.48 10.95 17.69 17.32 17.17 16.5
2.77 16.57 15.16 14.6 12.07 19.01 18.64 18.49 17.82
2.90 17.42 16.02 15.46 12.93 20.02 19.65 19.5 18.83
2.97 17.88 16.48 15.92 13.39 20.56 20.19 20.04 19.37
3.00 18.08 16.68 16.11 13.59 20.79 20.42 20.27 19.61
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 109
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 4-5 Lobe 7.0 Stage HR SERIES 3
110 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 4-5 7.0 STAGE HR SERIES 3
B 350 6000
A (BIT TO BEND) (8135)
(BIT TO 5565
STAB.) 600 GPM (2271 LPM)
300 (7545)
5000
(8688)
1260
(6779)
250
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 200
70%
Dynamic 131700 lbf 58580 daN
Bearing Load - Off Bottom UE 1000
50 RQ
Static 420400 lbf 187000 daN TO (1356)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.24 - - - 0.97 1.34 1.48 2.14 1.25 5.44 3.6 2.87 - 6.66 6.43 6.58 7.24
0.78 2.79 1.25 0.63 - 3.4 3.51 3.66 4.31 1.50 7.07 5.24 4.51 1.21 8.48 8.12 8.03 8.69
1.15 5.21 3.67 3.05 0.28 6.2 5.83 5.72 6.37 1.75 8.71 6.87 6.14 2.84 10.31 9.94 9.8 10.14
1.50 7.51 5.96 5.35 2.57 8.84 8.47 8.33 8.32 2.00 10.34 8.51 7.78 4.48 12.14 11.77 11.62 11.6
1.83 9.66 8.12 7.5 4.73 11.33 10.97 10.82 10.16 2.25 11.98 10.15 9.41 6.11 13.96 13.6 13.45 13.05
2.12 11.56 10.02 9.4 6.62 13.52 13.16 13.01 12.35
2.38 13.26 11.72 11.1 8.33 15.48 15.12 14.97 14.31
2.60 14.7 13.16 12.54 9.76 17.14 16.78 16.63 15.97
2.77 15.81 14.27 13.65 10.88 18.43 18.06 17.91 17.25
2.90 16.66 15.12 14.5 11.73 19.41 19.04 18.89 18.24
2.97 17.12 15.58 14.96 12.18 19.93 19.57 19.42 18.76
3.00 17.32 15.77 15.16 12.38 20.16 19.8 19.65 18.99
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 111
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 6-7 Lobe 5.0 Stage HR SERIES 3
112 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 6-7 5.0 STAGE HR SERIES 3
B 200
A (BIT TO BEND) 600 GPM (2271 LPM)
(BIT TO
STAB.) 180 10000
(13558)
(8688)
9762
1260
160
(13235)
450 GPM (1703 LPM) 8000
140
(10846)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm
6000
Bit Box Connection 4-1/2 REGULAR 100 300 GPM (1136 LPM) (8135)
70%
420400 lbf 187000 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.25 - - - 1.02 1.42 1.58 2.3 1.25 5.67 3.76 3 - 6.96 6.71 6.87 7.59
0.78 2.91 1.3 0.66 - 3.55 3.67 3.83 4.55 1.50 7.38 5.47 4.7 1.26 8.87 8.47 8.38 9.1
1.15 5.44 3.83 3.19 0.29 6.49 6.08 5.96 6.68 1.75 9.09 7.18 6.41 2.97 10.79 10.39 10.23 10.61
1.50 7.83 6.22 5.58 2.68 9.26 8.86 8.7 8.7 2.00 10.8 8.88 8.12 4.68 12.7 12.3 12.14 12.11
1.83 10.09 8.48 7.83 4.93 11.88 11.48 11.32 10.6 2.25 12.5 10.59 9.82 6.38 14.62 14.22 14.06 13.62
2.12 12.07 10.46 9.81 6.91 14.18 13.78 13.62 12.9
2.38 13.84 12.23 11.59 8.69 16.24 15.84 15.68 14.96
2.60 15.34 13.73 13.09 10.19 17.98 17.58 17.42 16.7
2.77 16.5 14.89 14.25 11.35 19.33 18.93 18.77 18.05
2.90 17.39 15.78 15.14 12.24 20.36 19.96 19.8 19.08
2.97 17.87 16.26 15.61 12.72 20.91 20.51 20.35 19.63
3.00 18.07 16.46 15.82 12.92 21.15 20.75 20.59 19.87
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 113
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.0 Stage HR SERIES 3
114 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 2.0 STAGE HR SERIES 3
B
A (BIT TO BEND)
(BIT TO 500 GPM (1892 LPM) 8000
STAB.) 80 (10846)
(3103)
7200
450
(9762)
375 GPM (1419 LPM) 6000
60
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm
Bit Box Connection 4-1/2 REGULAR 250 GPM (946 LPM) 4000
70%
Static RQ
420400 lbf 187000 daN TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.29 - - - 1.22 1.76 1.98 2.97 1.25 6.59 4.37 3.48 - 8.11 7.79 8 8.99
0.78 3.39 1.52 0.77 - 4.11 4.29 4.51 5.49 1.50 8.58 6.35 5.46 1.47 10.38 9.83 9.71 10.7
1.15 6.32 4.45 3.7 0.34 7.6 7.06 6.9 7.89 1.75 10.56 8.34 7.45 3.45 12.65 12.1 11.88 12.41
1.50 9.1 7.23 6.48 3.11 10.91 10.36 10.14 10.15 2.00 12.54 10.32 9.43 5.43 14.91 14.37 14.15 14.12
1.83 11.72 9.85 9.1 5.73 14.02 13.47 13.25 12.28 2.25 14.53 12.3 11.42 7.42 17.18 16.63 16.41 15.82
2.12 14.02 12.15 11.4 8.03 16.76 16.21 15.99 15
2.38 16.08 14.21 13.46 10.1 19.21 18.66 18.44 17.46
2.60 17.83 15.96 15.21 11.84 21.29 20.74 20.52 19.53
2.77 19.18 17.31 16.56 13.19 22.89 22.34 22.12 21.14
2.90 20.21 18.34 17.59 14.22 24.12 23.57 23.35 22.36
2.97 20.76 18.89 18.14 14.78 24.78 24.23 24.01 23.02
3.00 21 19.13 18.38 15.01 25.06 24.51 24.29 23.31
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 115
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 2.9 Stage HR SERIES 3
116 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 2.9 STAGE HR SERIES 3
B 120 14000
A (BIT TO BEND) (18981)
(BIT TO 12735
STAB.)
600 GPM (2271 LPM) 12000 (17266)
100
(6033)
(16270)
875
10000
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 8000
(10846)
Bit Box Connection 4-1/2 REGULAR 60
70%
420400 lbf 187000 daN TO (2712)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.24 - - - 0.96 1.31 1.45 2.09 1.25 5.35 3.55 2.83 - 6.55 6.34 6.48 7.11
0.78 2.75 1.23 0.62 - 3.35 3.45 3.6 4.23 1.50 6.96 5.16 4.44 1.19 8.35 7.99 7.91 8.55
1.15 5.13 3.62 3.01 0.27 6.1 5.74 5.63 6.27 1.75 8.57 6.77 6.05 2.8 10.14 9.79 9.65 9.98
1.50 7.39 5.87 5.26 2.53 8.69 8.34 8.2 8.19 2.00 10.18 8.38 7.66 4.41 11.94 11.58 11.44 11.41
1.83 9.52 8 7.39 4.66 11.14 10.79 10.65 10.01 2.25 11.8 9.99 9.27 6.02 13.73 13.38 13.24 12.85
2.12 11.39 9.87 9.26 6.52 13.29 12.94 12.8 12.16
2.38 13.06 11.54 10.93 8.2 15.22 14.87 14.73 14.09
2.60 14.48 12.96 12.35 9.61 16.85 16.5 16.36 15.72
2.77 15.57 14.05 13.44 10.71 18.11 17.76 17.62 16.98
2.90 16.41 14.89 14.28 11.55 19.08 18.72 18.58 17.94
2.97 16.86 15.34 14.73 12 19.6 19.24 19.1 18.46
3.00 17.05 15.53 14.92 12.19 19.82 19.46 19.32 18.68
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 117
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage SERIES 3
118 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.0 STAGE SERIES 3
B 200 5000
(3100)
A (BIT TO BEND) (6779)
450
(BIT TO
STAB.) 600 GPM (2271 LPM) 4190
(5670)
160 4000
(5423)
450 GPM (1703 LPM)
70%
Static 420400 lbf 187000 daN RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400 500
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2578) (3448)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 3.0 Stage Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 450 psi 3,103 kPa 300 1,136 55 - 84
C = Overall Length 247.7 in 6292 mm Max Torque @ No Load 4,190 ft-lbs 5,681 Nm 450 1,703 99 - 127
Weight 1816 lbs 823.7 kg Max Power 113 HP 84 kW 600 2,271 142 - 170
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.32 - - - 1.37 2.06 2.33 3.56 1.25 7.32 4.85 3.86 - 9.03 8.63 8.91 10.14
0.78 3.76 1.68 0.85 - 4.55 4.78 5.05 6.28 1.50 9.52 7.05 6.07 1.63 11.58 10.9 10.76 11.99
1.15 7.02 4.94 4.11 0.37 8.5 7.82 7.64 8.87 1.75 11.72 9.26 8.27 3.83 14.14 13.46 13.18 13.85
1.50 10.1 8.03 7.2 3.46 12.24 11.55 11.28 11.31 2.00 13.92 11.46 10.47 6.03 16.7 16.01 15.74 15.71
1.83 13.01 10.93 10.1 6.36 15.76 15.08 14.81 13.61 2.25 16.13 13.66 12.67 8.23 19.25 18.57 18.29 17.57
2.12 15.57 13.49 12.66 8.92 18.86 18.18 17.9 16.67
2.38 17.86 15.78 14.95 11.21 21.64 20.95 20.68 19.45
2.60 19.79 17.72 16.88 13.15 23.99 23.3 23.03 21.8
2.77 21.29 19.21 18.38 14.64 25.8 25.12 24.84 23.61
2.90 22.43 20.36 19.53 15.79 27.19 26.5 26.23 25
2.97 23.05 20.97 20.14 16.4 27.93 27.25 26.98 25.75
3.00 23.31 21.24 20.41 16.67 28.26 27.57 27.3 26.07
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 119
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SERIES 3
120 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.0 STAGE HR SERIES 3
B 200
A (BIT TO BEND)
(4650)
7000
680
(BIT TO
STAB.) 600 GPM (2271 LPM) (9491)
6280
160 6000 (8510)
(8135)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 120
4000
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM)
(5423)
70%
1000
Static 420400 lbf 187000 daN RQ
TO (1356)
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400 500 600 700
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 3.0 Stage HR Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 680 psi 4,688 kPa 300 1,136 55 - 84
C = Overall Length 247.7 in 6292 mm Max Torque @ No Load 6,280 ft-lbs 8,515 Nm 450 1,703 99 - 127
Weight 1816 lbs 823.7 kg Max Power 170 HP 127 kW 600 2,271 142 - 170
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.32 - - - 1.37 2.06 2.33 3.56 1.25 7.32 4.85 3.86 - 9.03 8.63 8.91 10.14
0.78 3.76 1.68 0.85 - 4.55 4.78 5.05 6.28 1.50 9.52 7.05 6.07 1.63 11.58 10.9 10.76 11.99
1.15 7.02 4.94 4.11 0.37 8.5 7.82 7.64 8.87 1.75 11.72 9.26 8.27 3.83 14.14 13.46 13.18 13.85
1.50 10.1 8.03 7.2 3.46 12.24 11.55 11.28 11.31 2.00 13.92 11.46 10.47 6.03 16.7 16.01 15.74 15.71
1.83 13.01 10.93 10.1 6.36 15.76 15.08 14.81 13.61 2.25 16.13 13.66 12.67 8.23 19.25 18.57 18.29 17.57
2.12 15.57 13.49 12.66 8.92 18.86 18.18 17.9 16.67
2.38 17.86 15.78 14.95 11.21 21.64 20.95 20.68 19.45
2.60 19.79 17.72 16.88 13.15 23.99 23.3 23.03 21.8
2.77 21.29 19.21 18.38 14.64 25.8 25.12 24.84 23.61
2.90 22.43 20.36 19.53 15.79 27.19 26.5 26.23 25
2.97 23.05 20.97 20.14 16.4 27.93 27.25 26.98 25.75
3.00 23.31 21.24 20.41 16.67 28.26 27.57 27.3 26.07
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 121
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR SLOW SERIES 3
122 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.0 STAGE HR SLOW SERIES 3
B 180
A
(4688)
(BIT TO BEND)
680
(BIT TO
STAB.)
12000
600 GPM (2271 LPM) (16270)
90 10800
(14640)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm (12202)
70%
Static 420400 lbf 187000 daN UE
RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400 500 600 700
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 3.0 Stage HR SLOW Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 680 psi 4,688 kPa 300 1,136 35 - 46
C = Overall Length 326.7 in 8298 mm Max Torque @ No Load 10,800 ft-lbs 14,643 Nm 450 1,703 58 - 70
Weight 2402 lbs 1089.5 kg Max Power 165 HP 123 kW 600 2,271 80 - 93
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.0 Stage HR
SLOW SERIES 3 SLOW SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.25 - - - 1.01 1.4 1.55 2.26 1.25 5.61 3.72 2.96 - 6.87 6.63 6.79 7.49
0.78 2.88 1.29 0.65 - 3.51 3.62 3.78 4.48 1.50 7.29 5.4 4.65 1.25 8.76 8.37 8.28 8.98
1.15 5.38 3.79 3.15 0.29 6.4 6.01 5.89 6.59 1.75 8.98 7.09 6.33 2.93 10.65 10.26 10.1 10.47
1.50 7.74 6.15 5.51 2.65 9.14 8.75 8.6 8.59 2.00 10.67 8.78 8.02 4.62 12.54 12.15 11.99 11.97
1.83 9.97 8.38 7.74 4.88 11.72 11.33 11.18 10.47 2.25 12.35 10.46 9.71 6.31 14.43 14.04 13.88 13.46
2.12 11.92 10.33 9.7 6.83 13.99 13.6 13.44 12.74
2.38 13.68 12.09 11.45 8.59 16.02 15.63 15.48 14.77
2.60 15.16 13.57 12.93 10.07 17.74 17.35 17.2 16.49
2.77 16.31 14.72 14.08 11.22 19.07 18.68 18.53 17.82
2.90 17.19 15.59 14.96 12.09 20.09 19.7 19.54 18.84
2.97 17.66 16.07 15.43 12.57 20.64 20.24 20.09 19.39
3.00 17.86 16.27 15.63 12.77 20.87 20.48 20.32 19.62
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 123
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR SERIES 3
124 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.3 STAGE HR SERIES 3
B 120
A (BIT TO BEND) 16000
(BIT TO
STAB.) 600 GPM (2271 LPM) (21693)
15610
100
(6516)
14000 (21164)
945
(18981)
12000
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 10000
(13558)
Bit Box Connection 4-1/2 REGULAR 60
300 GPM (1136 LPM) 8000
70%
2000
(2712)
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6206) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 3.3 Stage HR Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 945 psi 6,516 kPa 300 1,136 35 - 51
C = Overall Length 367.7 in 9340 mm Max Torque @ No Load 15,610 ft-lbs 21,164 Nm 450 1,703 60 - 77
Weight 2612 lbs 1184.8 kg Max Power 253 HP 188 kW 600 2,271 85 - 102
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.3 Stage HR
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.22 - - - 0.88 1.19 1.31 1.87 1.25 5 3.31 2.64 - 6.11 5.92 6.04 6.6
0.78 2.57 1.15 0.58 - 3.13 3.22 3.34 3.9 1.50 6.5 4.82 4.14 1.11 7.78 7.47 7.39 7.95
1.15 4.8 3.38 2.81 0.26 5.67 5.37 5.27 5.82 1.75 8.01 6.32 5.65 2.62 9.44 9.13 9.01 9.3
1.50 6.9 5.48 4.92 2.36 8.08 7.77 7.65 7.64 2.00 9.51 7.83 7.15 4.12 11.11 10.8 10.68 10.65
1.83 8.89 7.47 6.9 4.35 10.34 10.04 9.91 9.36 2.25 11.02 9.33 8.66 5.62 12.77 12.46 12.34 12
2.12 10.63 9.21 8.65 6.09 12.33 12.03 11.9 11.35
2.38 12.2 10.78 10.21 7.66 14.12 13.81 13.69 13.13
2.60 13.52 12.1 11.53 8.98 15.63 15.32 15.2 14.64
2.77 14.54 13.12 12.56 10 16.79 16.49 16.36 15.81
2.90 15.32 13.91 13.34 10.78 17.69 17.38 17.25 16.7
2.97 15.75 14.33 13.76 11.21 18.17 17.86 17.73 17.18
3.00 15.93 14.51 13.94 11.39 18.37 18.06 17.94 17.39
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 125
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR SERIES 3
126 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 3.5 STAGE HR SERIES 3
B 100
(5430)
A (BIT TO BEND)
790
(BIT TO
STAB.)
400 GPM (1514 LPM)
10000
80 (13558)
9840
(13350)
8000
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 60
6000
Bit Box Connection 4-1/2 REGULAR
70%
Static 420400 lbf 187000 daN UE (2712)
RQ
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 100 200 300 400 500 600 700 800 900
Absolute Overpull 546000 lbf 243000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6206)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 3.5 Stage HR Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.21 rev/gal 0.05 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 790 psi 5,447 kPa 150 568 22 - 31
C = Overall Length 354 in 8992 mm Max Torque @ No Load 9,840 ft-lbs 13,341 Nm 275 1,041 47 - 57
Weight 2586 lbs 1173 kg Max Power 135 HP 101 kW 400 1,514 72 - 83
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 3.5 Stage HR
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.23 - - - 0.92 1.25 1.39 1.98 1.25 5.19 3.44 2.74 - 6.35 6.14 6.27 6.87
0.78 2.67 1.19 0.6 - 3.25 3.34 3.48 4.07 1.50 6.75 5 4.3 1.15 8.08 7.75 7.67 8.27
1.15 4.98 3.5 2.91 0.26 5.9 5.57 5.46 6.06 1.75 8.31 6.56 5.86 2.71 9.81 9.48 9.35 9.66
1.50 7.16 5.69 5.1 2.45 8.4 8.07 7.94 7.93 2.00 9.87 8.12 7.42 4.27 11.55 11.22 11.08 11.06
1.83 9.22 7.75 7.16 4.51 10.77 10.43 10.3 9.7 2.25 11.43 9.68 8.98 5.84 13.28 12.95 12.82 12.45
2.12 11.03 9.56 8.97 6.32 12.84 12.51 12.38 11.78
2.38 12.66 11.18 10.59 7.94 14.7 14.37 14.24 13.64
2.60 14.03 12.56 11.97 9.32 16.28 15.94 15.81 15.21
2.77 15.09 13.62 13.03 10.38 17.49 17.16 17.03 16.43
2.90 15.9 14.43 13.84 11.19 18.42 18.09 17.96 17.36
2.97 16.34 14.86 14.28 11.63 18.92 18.59 18.46 17.86
3.00 16.52 15.05 14.46 11.81 19.14 18.8 18.67 18.07
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 127
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR SERIES 3
128 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 4.8 STAGE HR SERIES 3
B 140
A (BIT TO BEND)
(BIT TO
10000
STAB.) 400 GPM (1514 LPM)
120 (13558)
9948
(13488)
(9412)
1365
100 8000
(10846)
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 80
6000
Bit Box Connection 4-1/2 REGULAR (8135)
70%
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 546000 lbf 243000 daN (1379) (2578) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 4.8 Stage HR Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.33 rev/gal 0.09 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 1,365 psi 9,411 kPa 200 757 51 - 66
C = Overall Length 326.2 in 8285 mm Max Torque @ No Load 9,948 ft-lbs 13,488 Nm 300 1,136 84 - 99
Weight 2257 lbs 1023.8 kg Max Power 220 HP 164 kW 400 1,514 116 - 132
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 4.8 Stage HR
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.25 - - - 1.01 1.4 1.56 2.26 1.25 5.61 3.72 2.96 - 6.88 6.64 6.8 7.5
0.78 2.88 1.29 0.65 - 3.51 3.63 3.79 4.49 1.50 7.3 5.41 4.65 1.25 8.78 8.38 8.29 9
1.15 5.39 3.79 3.16 0.29 6.41 6.02 5.9 6.6 1.75 8.99 7.1 6.34 2.94 10.67 10.28 10.12 10.49
1.50 7.75 6.16 5.52 2.65 9.16 8.76 8.61 8.6 2.00 10.68 8.79 8.03 4.63 12.56 12.17 12.01 11.98
1.83 9.98 8.39 7.75 4.88 11.74 11.35 11.19 10.49 2.25 12.37 10.48 9.72 6.32 14.45 14.06 13.91 13.48
2.12 11.94 10.35 9.71 6.84 14.01 13.62 13.47 12.76
2.38 13.7 12.11 11.47 8.6 16.05 15.66 15.5 14.8
2.60 15.18 13.59 12.95 10.09 17.77 17.38 17.22 16.52
2.77 16.33 14.74 14.1 11.23 19.1 18.71 18.56 17.85
2.90 17.21 15.62 14.98 12.11 20.12 19.73 19.57 18.87
2.97 17.68 16.09 15.45 12.58 20.67 20.28 20.12 19.42
3.00 17.89 16.29 15.66 12.79 20.9 20.51 20.36 19.65
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 129
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR SERIES 3
130 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 in & 6-3/4 in (165 mm & 171 mm) 7-8 5.0 STAGE HR SERIES 3
B 180 14000
A (BIT TO BEND) 600 GPM (2271 LPM) (18981)
(BIT TO 12813
STAB.) 160
12000 (17372)
(16270)
(10377)
140
1505
450 GPM (1703 LPM)
10000
120
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 100 8000
(10846)
300 GPM (1136 LPM)
Bit Box Connection 4-1/2 REGULAR
70%
Bearing Load - Off Bottom 2000
Static 420400 lbf 187000 daN 20 UE
RQ (2712)
TO
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 546000 lbf 243000 daN (1379) (2578) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 1,505 psi 10,377 kPa 300 1,136 73 - 84
C = Overall Length 326.7 in 8298 mm Max Torque @ No Load 12,813 ft-lbs 17,372 Nm 450 1,703 115 - 126
Weight 2446 lbs 1109.5 kg Max Power 381 HP 164 kW 600 2,271 156 - 168
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.0 Stage HR
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.25 - - - 1.01 1.4 1.55 2.26 1.25 5.61 3.72 2.96 - 6.87 6.63 6.79 7.49
0.78 2.88 1.29 0.65 - 3.51 3.62 3.78 4.48 1.50 7.29 5.4 4.65 1.25 8.76 8.37 8.28 8.98
1.15 5.38 3.79 3.15 0.29 6.4 6.01 5.89 6.59 1.75 8.98 7.09 6.33 2.93 10.65 10.26 10.1 10.47
1.50 7.74 6.15 5.51 2.65 9.14 8.75 8.6 8.59 2.00 10.67 8.78 8.02 4.62 12.54 12.15 11.99 11.97
1.83 9.97 8.38 7.74 4.88 11.72 11.33 11.18 10.47 2.25 12.35 10.46 9.71 6.31 14.43 14.04 13.88 13.46
2.12 11.92 10.33 9.7 6.83 13.99 13.6 13.44 12.74
2.38 13.68 12.09 11.45 8.59 16.02 15.63 15.48 14.77
2.60 15.16 13.57 12.93 10.07 17.74 17.35 17.2 16.49
2.77 16.31 14.72 14.08 11.22 19.07 18.68 18.53 17.82
2.90 17.19 15.59 14.96 12.09 20.09 19.7 19.54 18.84
2.97 17.66 16.07 15.43 12.57 20.64 20.24 20.09 19.39
3.00 17.86 16.27 15.63 12.77 20.87 20.48 20.32 19.62
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 131
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.7 Stage HR SERIES 3
132 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.7 STAGE HR SERIES 3 15922
B 160 (21587)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 16000
STAB.) 140 (21693)
(11342)
1645
14000
(18981)
120
450 GPM (1703 LPM) 12000
SPEED (RPM)
Bit Size Range 7-7/8 - 9-7/8 in 200 - 251 mm 10000
(13558)
80
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM) 8000
70%
(2712)
Max. Overpull for Re-run 328000 lbf 146000 daN 0
0 200 400 600 800 1000 1200 1400 1600 1800
Absolute Overpull 546000 lbf 243000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032) (12411)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 16.45 in 418 mm
Lobe Configuration 7-8 Lobe 5.7 Stage HR Flow Rate Speed
Adjustable 64.97 in 1650 mm
B = Bit to Bend Displacement 0.24 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 52.97 in 1345 mm
Max Differential @ No Load 1,645 psi 11,342 kPa 300 1,136 53 - 72
C = Overall Length 382.7 in 9721 mm Max Torque @ No Load 15,922 ft-lbs 21,587 Nm 450 1,703 90 - 108
Weight 2860 lbs 1297.3 kg Max Power 382 HP 285 kW 600 2,271 126 - 144
ADJUSTABLE BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.7 Stage HR FBH BUILD RATE: 6-1/2 & 6-3/4 in (165 & 171 mm) 7-8 Lobe 5.7 Stage HR
SERIES 3 SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8 Size 7-7/8 8-1/2 8-3/4 9-7/8 7-7/8 8-1/2 8-3/4 9-7/8
(200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm) (200 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.21 - - - 0.85 1.13 1.24 1.75 1.25 4.81 3.19 2.54 - 5.87 5.7 5.81 6.32
0.78 2.47 1.11 0.56 - 3.02 3.09 3.21 3.72 1.50 6.26 4.63 3.99 1.07 7.47 7.19 7.12 7.63
1.15 4.61 3.25 2.7 0.25 5.45 5.16 5.07 5.58 1.75 7.7 6.08 5.43 2.52 9.06 8.78 8.67 8.93
1.50 6.64 5.27 4.73 2.27 7.75 7.46 7.35 7.34 2.00 9.15 7.53 6.88 3.96 10.66 10.38 10.26 10.24
1.83 8.55 7.18 6.64 4.18 9.92 9.63 9.52 9.01 2.25 10.6 8.98 8.33 5.41 12.25 11.97 11.86 11.54
2.12 10.23 8.86 8.32 5.86 11.82 11.54 11.42 10.91
2.38 11.73 10.37 9.82 7.37 13.53 13.24 13.13 12.62
2.60 13.01 11.64 11.09 8.64 14.97 14.69 14.58 14.07
2.77 13.99 12.62 12.08 9.62 16.09 15.81 15.69 15.18
2.90 14.74 13.38 12.83 10.37 16.94 16.66 16.55 16.04
2.97 15.15 13.78 13.24 10.78 17.4 17.12 17.01 16.49
3.00 15.32 13.95 13.41 10.95 17.6 17.32 17.2 16.69
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 133
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-3/4 in (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 2 SHORT
134 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 4-5 7.0 STAGE HR SERIES 2 SHORT
B 350 6000
A (BIT TO BEND) (8135)
(BIT TO 5565
STAB.) 600 GPM (2271 LPM)
300 (7545)
5000
(8688)
1260
(6779)
250
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 200
70%
TO
Max. Overpull for Re-run 602600 lbf 268000 daN 0
0 200 400 600 800 1000 1200 1400
Absolute Overpull 1004400 lbf 447000 daN (1379) (2578) (4137) (5516) (6895) (8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 17.2 in 437 mm
Lobe Configuration 4-5 Lobe 7.0 Stage HR Flow Rate Speed
Adjustable 66 in 1676 mm
B = Bit to Bend Displacement 0.50 rev/gal 0.13 rev/l GPM LPM RPM
Fixed 54 in 1372 mm
Max Differential @ No Load 1,260 psi 8,687 kPa 300 1,136 80 - 150
C = Overall Length 335.7 in 8527 mm Max Torque @ No Load 5,565 ft-lbs 7,545 Nm 450 1,703 158 - 225
Weight 2478 lbs 1124 kg Max Power 249 HP 186 kW 600 2,271 235 - 300
ADJUSTABLE BUILD RATE: 6-3/4 in (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 2 SHORT FBH BUILD RATE: 6-3/4 in (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 2 SHORT
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.24 1.39 2.06 1.25 4.97 4.25 0.99 6.77 6.63 7.17
0.78 2.39 1.78 - 3.51 3.57 4.23 1.50 6.62 5.89 2.63 8.61 8.46 8.62
1.15 4.82 4.21 1.46 6.32 6.18 6.3 1.75 8.26 7.54 4.28 10.45 10.3 10.08
1.50 7.12 6.51 3.76 8.98 8.84 8.25 2.00 9.9 9.18 5.92 12.29 12.14 11.54
1.83 9.29 8.68 5.93 11.49 11.34 10.68 2.25 11.55 10.82 7.56 14.12 13.98 13.31
2.12 11.2 10.59 7.83 13.69 13.55 12.88
2.38 12.91 12.3 9.54 15.67 15.52 14.85
2.60 14.35 13.74 10.99 17.34 17.19 16.52
2.77 15.47 14.86 12.1 18.63 18.48 17.82
2.90 16.32 15.71 12.96 19.62 19.47 18.8
2.97 16.78 16.17 13.42 20.15 20 19.33
3.00 16.98 16.37 13.62 20.38 20.23 19.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 135
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-3/4 in (171 mm) 6-7 Lobe 5.0 Stage HR SERIES 2 SHORT
136 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 6-7 5.0 STAGE HR SERIES 2 SHORT
B 200
A (BIT TO BEND) 600 GPM (2271 LPM)
(BIT TO
STAB.) 180 10000
(13558)
160 9762
(13235)
450 GPM (1703 LPM) 8000
140
(10846)
70%
Bearing Load - Off Bottom
Static 510500 lbf 227080 daN UE (2712)
20 RQ
TO
Max. Overpull for Re-run 602600 lbf 268000 daN 0
0 200 400 600 800 1000 1200 1400
Absolute Overpull 1004400 lbf 447000 daN (1379) (2578) (4137) (5516) (6895) (8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 17.2 in 437 mm
Lobe Configuration 6-7 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 66 in 1676 mm
B = Bit to Bend Displacement 0.31 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 54 in 1372 mm
Max Differential @ No Load 1,260 psi 8,687 kPa 300 1,136 56 - 93
C = Overall Length 321.1 in 8156 mm Max Torque @ No Load 9,762 ft-lbs 13,235 Nm 450 1,703 103 - 140
Weight 2450 lbs 1111.3 kg Max Power 279 HP 208 kW 600 2,271 150 - 186
ADJUSTABLE BUILD RATE: 6-3/4 in (171 mm) 6-7 Lobe 5.0 Stage HR SERIES 2 SHORT FBH BUILD RATE: 6-3/4 in (171 mm) 6-7 Lobe 5.0 Stage HR SERIES 2 SHORT
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.32 1.48 2.21 1.25 5.19 4.44 1.03 7.08 6.92 7.51
0.78 2.49 1.86 - 3.67 3.73 4.46 1.50 6.91 6.15 2.75 9.01 8.85 9.02
1.15 5.03 4.4 1.52 6.62 6.46 6.6 1.75 8.62 7.87 4.46 10.94 10.78 10.53
1.50 7.44 6.8 3.92 9.42 9.26 8.62 2.00 10.34 9.58 6.18 12.87 12.7 12.05
1.83 9.7 9.06 6.19 12.05 11.89 11.16 2.25 12.05 11.3 7.89 14.79 14.63 13.9
2.12 11.69 11.05 8.18 14.37 14.2 13.47
2.38 13.47 12.84 9.96 16.44 16.28 15.55
2.60 14.98 14.34 11.47 18.2 18.03 17.3
2.77 16.15 15.51 12.64 19.55 19.39 18.66
2.90 17.04 16.4 13.53 20.59 20.43 19.7
2.97 17.52 16.88 14.01 21.15 20.99 20.26
3.00 17.73 17.09 14.21 21.39 21.22 20.5
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 137
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-3/4 in (171 mm) 7-8 Lobe 2.9 Stage HR SERIES 2 SHORT
138 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 2.9 STAGE HR SERIES 2 SHORT
B 120 14000
A (BIT TO BEND) (18981)
(BIT TO 12735
STAB.) (17266)
600 GPM (2271 LPM) 12000
100
(16270)
(6033)
875
10000
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 8000
60 (10846)
Bit Box Connection 4-1/2 REGULAR
70%
510500 lbf 227080 daN RQ (2712)
TO
Max. Overpull for Re-run 602600 lbf 268000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 1004400 lbf 447000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6506) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 17.2 in 437 mm
Lobe Configuration 7-8 Lobe 2.9 Stage HR Flow Rate Speed
Adjustable 66 in 1676 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 54 in 1372 mm
Max Differential @ No Load 875 psi 6,033 kPa 300 1,136 30 - 50
C = Overall Length 341.1 in 8664 mm Max Torque @ No Load 12,735 ft-lbs 17,266 Nm 450 1,703 55 - 75
Weight 2589 lbs 1174.4 kg Max Power 194 HP 145 kW 600 2,271 80 - 99
ADJUSTABLE BUILD RATE: 6-3/4 in (171 mm) 7-8 Lobe 2.9 Stage HR SERIES 2 SHORT FBH BUILD RATE: 6-3/4 in (171 mm) 7-8 Lobe 2.9 Stage HR SERIES 2 SHORT
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.22 1.36 2.01 1.25 4.9 4.18 0.97 6.67 6.52 7.05
0.78 2.35 1.75 - 3.46 3.51 4.16 1.50 6.52 5.8 2.59 8.47 8.33 8.48
1.15 4.75 4.15 1.44 6.22 6.08 6.2 1.75 8.13 7.42 4.21 10.28 10.14 9.92
1.50 7.01 6.41 3.7 8.83 8.69 8.12 2.00 9.75 9.04 5.83 12.09 11.94 11.36
1.83 9.15 8.55 5.84 11.3 11.15 10.51 2.25 11.37 10.66 7.45 13.89 13.75 13.1
2.12 11.03 10.42 7.71 13.46 13.32 12.67
2.38 12.71 12.11 9.4 15.4 15.26 14.61
2.60 14.13 13.53 10.82 17.04 16.9 16.25
2.77 15.23 14.63 11.92 18.31 18.17 17.52
2.90 16.07 15.47 12.76 19.28 19.14 18.49
2.97 16.53 15.92 13.21 19.8 19.66 19.01
3.00 16.72 16.12 13.41 20.03 19.88 19.24
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 139
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-3/4 in (171 mm) 7-8 Lobe 5.0 Stage HR SERIES 2 SHORT
140 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 5.0 STAGE HR SERIES 2 SHORT 9000
B 180 (2712)
A (BIT TO BEND) 600 GPM (2271 LPM)
(BIT TO 8000
STAB.) 160 8167 (10846)
(6819)
(11073)
989
7000
140 (2712)
450 GPM (1703 LPM)
6000
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 100
5000
(2712)
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM)
4000
70%
Bearing Load - Off Bottom UE 1000
Static 510500 lbf 227080 daN 20 RQ (2712)
TO
Max. Overpull for Re-run 602600 lbf 268000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 1004400 lbf 447000 daN (1379) (2578) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 17.2 in 437 mm
Lobe Configuration 7-8 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 66 in 1676 mm
B = Bit to Bend Displacement 0.28 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 54 in 1372 mm
Max Differential @ No Load 989 psi 6,819 kPa 300 1,136 73 - 84
C = Overall Length 325.1 in 8258 mm Max Torque @ No Load 8,167 ft-lbs 11,073 Nm 450 1,703 115 - 126
Weight 2534 lbs 1149.4 kg Max Power 243 HP 181 kW 600 2,271 156 - 168
ADJUSTABLE BUILD RATE: 6-3/4 in (171 mm) 7-8 Lobe 5.0 Stage HR SERIES 2 SHORT FBH BUILD RATE:6-3/4 in (171 mm) 7-8 Lobe 5.0 Stage HR SERIES 2 SHORT
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.3 1.45 2.16 1.25 5.13 4.38 1.02 7 6.84 7.41
0.78 2.46 1.83 - 3.63 3.68 4.4 1.50 6.83 6.08 2.71 8.9 8.74 8.91
1.15 4.97 4.34 1.5 6.54 6.38 6.51 1.75 8.52 7.77 4.41 10.8 10.64 10.41
1.50 7.35 6.72 3.88 9.3 9.14 8.51 2.00 10.22 9.47 6.11 12.7 12.54 11.9
1.83 9.59 8.95 6.11 11.89 11.74 11.02 2.25 11.91 11.16 7.8 14.6 14.45 13.73
2.12 11.55 10.92 8.08 14.18 14.02 13.31
2.38 13.31 12.68 9.84 16.22 16.06 15.35
2.60 14.8 14.17 11.33 17.95 17.8 17.08
2.77 15.96 15.33 12.49 19.29 19.13 18.42
2.90 16.84 16.21 13.37 20.31 20.16 19.44
2.97 17.31 16.68 13.84 20.86 20.71 19.99
3.00 17.52 16.88 14.04 21.1 20.94 20.23
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 141
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-3/4 in (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 2 SHORT
142 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 Lobe 5.7 STAGE HR SERIES 2 SHORT 15922
B 160 (21587)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 16000
STAB.) 140 (21693)
(11342)
1645
14000
(18981)
120
450 GPM (1703 LPM) 12000
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 10000
(13558)
80
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM) 8000
70%
162100 lbf 72110 daN UE (5423)
Bearing Load - Off Bottom RQ
Static 20 TO 2000
510500 lbf 227080 daN (2712)
Max. Overpull for Re-run 602600 lbf 268000 daN 0
0 200 400 600 800 1000 1200 1400 1600 1800
Absolute Overpull 1004400 lbf 447000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032) (12411)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 17.2 in 437 mm
Lobe Configuration 7-8 Lobe 5.7 Stage HR Flow Rate Speed
Adjustable 66 in 1676 mm
B = Bit to Bend Displacement 0.24 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 54 in 1372 mm
Max Differential @ No Load 1,645 psi 11,342 kPa 300 1,136 53 - 72
C = Overall Length 381.1 in 9680 mm Max Torque @ No Load 15,922 ft-lbs 21,587 Nm 450 1,703 90 - 108
Weight 2948 lbs 1337.2 kg Max Power 382 HP 285 kW 600 2,271 126 - 144
ADJUSTABLE BUILD RATE: 6-3/4 in (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 2 SHORT FBH BUILD RATE: 6-3/4 in (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 2 SHORT
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.06 1.18 1.69 1.25 4.4 3.76 0.87 5.97 5.85 6.27
0.78 2.11 1.57 - 3.1 3.14 3.66 1.50 5.85 5.21 2.33 7.57 7.46 7.58
1.15 4.26 3.72 1.29 5.55 5.43 5.53 1.75 7.3 6.66 3.78 9.17 9.06 8.89
1.50 6.3 5.76 3.32 7.86 7.74 7.29 2.00 8.76 8.12 5.23 10.78 10.66 10.2
1.83 8.22 7.68 5.24 10.04 9.92 9.41 2.25 10.21 9.57 6.69 12.38 12.27 11.75
2.12 9.9 9.36 6.93 11.95 11.84 11.32 2.38 10.96 10.32 7.44 13.21 13.1 12.58
2.38 11.41 10.87 8.44 13.67 13.56 13.04
2.60 12.69 12.15 9.72 15.12 15.01 14.49
2.77 13.68 13.14 10.7 16.25 16.13 15.62
2.90 14.43 13.89 11.46 17.1 16.99 16.47
2.97 14.84 14.3 11.86 17.57 17.45 16.94
3.00 15.01 14.47 12.04 17.76 17.65 17.13
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 143
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
6-3/4 in (171 mm) 9-10 Lobe 8.0 Stage HR SERIES 2 SHORT
144 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 9-10 Lobe 8.0 STAGE HR SERIES 2 SHORT 20000
B 200 (27117)
(13790)
A 700 GPM (2650 LPM)
2000
(BIT TO BEND)
(BIT TO 18155
STAB.) 180 (24615)
600 GPM (2271 LPM) 16000
160
(21693)
140 500 GPM (1893 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 120 (16270)
400 GPM (1514 LPM)
Bit Box Connection 4-1/2 REGULAR 100
Dynamic 4000
162100 lbf 72110 daN 40 (5423)
Bearing Load - Off Bottom
70%
UE
Static 510500 lbf 227080 daN 20 RQ
TO
Max. Overpull for Re-run 602600 lbf 268000 daN 0
0 500 1000 1500 2000 2500
Absolute Overpull 1004400 lbf 447000 daN (3448) (6895) (10343) (13790) (17237)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 17.2 in 437 mm
Lobe Configuration 9-10 Lobe 8.0 Stage HR Flow Rate Speed
Adjustable 66 in 1676 mm
B = Bit to Bend Displacement 0.27 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 54 in 1372 mm
Max Differential @ No Load 2,000 psi 13,790 kPa 400 1,514 80 - 108
C = Overall Length 381.1 in 9680 mm Max Torque @ No Load 18,155 ft-lbs 24,615 Nm 550 2,082 120 - 148
Weight 2980 lbs 1351.7 kg Max Power 553 HP 412 kW 700 2,650 160 - 188
ADJUSTABLE BUILD RATE: 6-3/4 in (171 mm) 9-10 Lobe 8.0 Stage HR SERIES 2 FBH BUILD RATE: 6-3/4 in (171 mm) 9-10 Lobe 8.0 Stage HR SERIES 2 SHORT
SHORT
SLICK STABILIZED
SLICK STABILIZED Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
Hole (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
BEND ANGLE
ANGLE Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
1.25 4.40 3.76 0.87 5.97 5.85 6.27
0.39 - - - 1.06 1.18 1.69
1.50 5.85 5.21 2.33 7.57 7.46 7.58
0.78 2.11 1.57 - 3.10 3.14 3.66 1.75 7.30 6.66 3.78 9.17 9.06 8.89
1.15 4.26 3.72 1.29 5.55 5.43 5.53 2.00 8.76 8.12 5.23 10.78 10.66 10.20
1.50 6.30 5.76 3.32 7.86 7.74 7.29 2.25 10.21 9.57 6.69 12.38 12.27 11.75
1.83 8.22 7.68 5.24 10.04 9.92 9.41 2.38 10.96 10.32 7.44 13.21 13.10 12.58
2.12 9.90 9.36 6.93 11.95 11.84 11.32
2.38 11.41 10.87 8.44 13.67 13.56 13.04
2.60 12.69 12.15 9.72 15.12 15.01 14.49
2.77 13.68 13.14 10.70 16.25 16.13 15.62
2.90 14.43 13.89 11.46 17.10 16.99 16.47
2.97 14.84 14.30 11.86 17.57 17.45 16.94
3.00 15.01 14.47 12.04 17.76 17.65 17.13
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 145
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 3
146 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 4-5 Lobe 7.0 STAGE HR SERIES 3 12000
B 350 (16270)
(11377)
A (BIT TO BEND)
1650
(BIT TO
STAB.) 600 GPM (2271 LPM)
300 10000
(13559)
8820
(11959)
250 8000
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 200
6000
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM)
(8135)
70%
50 UE
Static 509765 lbf 226750 daN RQ
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Absolute Overpull 742200 lbf 330000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032) (12411) (13790)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 4-5 Lobe 7.0 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.49 rev/gal 0.13 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,650 psi 11,376 kPa 300 1,136 114 - 147
C = Overall Length 341 in 8661 mm Max Torque @ No Load 8,820 ft-lbs 11,958 Nm 450 1,703 187 - 221
Weight 2142 lbs 971.6 kg Max Power 438 HP 327 kW 600 2,271 261 - 294
ADJUSTABLE BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 4-5 Lobe 7.0 Stage FBH BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 4-5 Lobe 7.0 Stage HR SERIES 3
HR SERIES 3 SLICK STABILIZED
Hole
SLICK STABILIZED Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
Hole (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE 1.25 7.76 7.07 3.96 6.87 6.73 6.89
0.39 2.24 1.66 - 1.12 1.26 1.91 1.50 9.38 8.69 5.57 8.69 8.55 8.32
0.78 4.77 4.18 1.54 3.64 3.50 4.03 1.75 11.00 10.31 7.19 10.51 10.37 9.74
1.15 7.17 6.58 3.94 6.43 6.28 6.05 2.00 12.62 11.93 8.81 12.34 12.19 11.55
1.50 9.43 8.85 6.20 9.06 8.92 8.27 2.25 14.24 13.55 10.43 14.16 14.01 13.37
1.83 11.57 10.98 8.34 11.54 11.40 10.76 2.50 15.86 15.16 12.05 15.98 15.84 15.19
2.12 13.45 12.86 10.22 13.73 13.58 12.94
2.38 15.13 14.54 11.90 15.68 15.54 14.90
2.60 16.55 15.97 13.32 17.34 17.20 16.55
2.77 17.65 17.07 14.42 18.62 18.47 17.83
2.90 18.49 17.91 15.26 19.60 19.45 18.81
2.97 18.95 18.36 15.72 20.12 19.98 19.34
3.00 19.14 18.55 15.91 20.35 20.20 19.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 147
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 3
148 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 Lobe 5.7 STAGE HR SERIES 3 18000
B 160 (24405)
(9239)
1340
A (BIT TO BEND)
(BIT TO 14200
STAB.)
140 600 GPM (2271 LPM) (19253)
14000
120 (18982)
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 10000
(13559)
Bit Box Connection 4-1/2 REGULAR 80
300 GPM (1136 LPM)
70%
20 UE 2000
Static 509765 lbf 226750 daN RQ (2712)
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 742200 lbf 330000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 7-8 Lobe 5.7 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.23 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,340 psi 9,239 kPa 300 1,136 53 - 69
C = Overall Length 391 in 9931 mm Max Torque @ No Load 14,200 ft-lbs 19,253 Nm 450 1,703 88 - 104
Weight 2598 lbs 1178.4 kg Max Power 331 HP 247 kW 600 2,271 122 - 138
ADJUSTABLE BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage FBH BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage
HR SERIES 3 HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.97 1.45 - 0.94 1.05 1.54 1.25 6.80 6.19 3.46 5.96 5.85 5.98
0.78 4.18 3.66 1.35 3.15 3.04 3.45 1.50 8.22 7.61 4.88 7.53 7.42 7.25
1.15 6.28 5.76 3.45 5.54 5.43 5.26 1.75 9.63 9.03 6.30 9.10 8.99 8.52
1.50 8.26 7.75 5.43 7.81 7.70 7.21 2.00 11.05 10.44 7.72 10.67 10.56 10.08
1.83 10.13 9.62 7.30 9.94 9.83 9.35 2.25 12.47 11.86 9.13 12.24 12.14 11.65
2.12 11.77 11.26 8.95 11.82 11.71 11.22 2.50 13.88 13.28 10.55 13.82 13.71 13.22
2.38 13.25 12.73 10.42 13.50 13.39 12.90
2.60 14.49 13.98 11.67 14.92 14.81 14.33
2.77 15.46 14.94 12.63 16.02 15.91 15.43
2.90 16.19 15.68 13.37 16.86 16.75 16.27
2.97 16.59 16.08 13.76 17.31 17.21 16.72
3.00 16.76 16.25 13.93 17.51 17.40 16.91
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 149
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 9-10 Lobe 8.0 Stage HR SERIES 3
150 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 9-10 Lobe 8.0 STAGE HR SERIES 3 20000
B 200 (27117)
(13790)
A 700 GPM (2650 LPM)
2000
(BIT TO BEND)
(BIT TO 18155
STAB.) 180 (24615)
600 GPM (2271 LPM) 16000
160
(21693)
140 500 GPM (1893 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 120 (16270)
400 GPM (1514 LPM)
Bit Box Connection 4-1/2 REGULAR 100
Dynamic 4000
151925 lbf 67580 daN 40 (5423)
Bearing Load - Off Bottom
70%
UE
Static 509765 lbf 226750 daN 20 RQ
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 500 1000 1500 2000 2500
Absolute Overpull 742200 lbf 330000 daN (3448) (6895) (10343) (13790) (17237)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 9-10 Lobe 8.0 Stage Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.27 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 2,000 psi 13,790 kPa 400 1,514 80 - 108
C = Overall Length 391 in 9931 mm Max Torque @ No Load 18,155 ft-lbs 24,615 Nm 550 2,082 120 - 148
Weight 2595 lbs 1177.1 kg Max Power 553 HP 412 kW 700 2,650 160 - 188
ADJUSTABLE BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 9-10 Lobe 8.0 Stage FBH BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 9-10 Lobe 8.0 Stage
HR SERIES 3 HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND
ANGLE ANGLE Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
0.39 0.39 1.97 1.45 0.94 1.05 1.54 1.25 6.80 6.19 3.46 5.96 5.85 5.98
0.78 0.78 4.18 3.66 3.15 3.04 3.45 1.50 8.22 7.61 4.88 7.53 7.42 7.25
1.15 1.15 6.28 5.76 5.54 5.43 5.26 1.75 9.63 9.03 6.30 9.10 8.99 8.52
1.50 1.50 8.26 7.75 7.81 7.70 7.21 2.00 11.05 10.44 7.72 10.67 10.56 10.08
1.83 1.83 10.13 9.62 9.94 9.83 9.35 2.25 12.47 11.86 9.13 12.24 12.14 11.65
2.12 2.12 11.77 11.26 11.82 11.71 11.22 2.50 13.88 13.28 10.55 13.82 13.71 13.22
2.38 2.38 13.25 12.73 13.50 13.39 12.90
2.60 2.60 14.49 13.98 14.92 14.81 14.33
2.77 2.77 15.46 14.94 16.02 15.91 15.43
2.90 2.90 16.19 15.68 16.86 16.75 16.27
2.97 2.97 16.59 16.08 17.31 17.21 16.72
3.00 3.00 16.76 16.25 17.51 17.40 16.91
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 151
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 2.9 Stage HR MUD LUBE
152 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 Lobe 2.9 STAGE HR MUD LUBE 11915
B 90 (16155)
(9239)
A (BIT TO BEND)
690
(BIT TO 500 GPM (1893 LPM)
STAB.) 80 10600
(14372)
70 9265
(12562)
400 GPM (1514 LPM)
60
20
Dynamic 100357 lbf 44640 daN
Bearing Load - Off Bottom
70%
UE 1320
Static 355612 lbf 158180 daN 10 RQ (1790)
TO
Max. Overpull for Re-run 432800 lbf 193000 daN 0 0
0 200 400 600 800
Absolute Overpull 721400 lbf 321000 daN (1379) (2758) (4137) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 21.1 in 536 mm
Lobe Configuration 7-8 Lobe 2.9 Stage HR Flow Rate Speed
Adjustable 66.7 in 1694 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 54.6 in 1387 mm
Max Differential @ No Load 690 psi 4,757 kPa 300 1,136 32 - 48
C = Overall Length 349.7 in 8882 mm Max Torque @ No Load 10,600 ft-lbs 14,372 Nm 400 1,514 48 - 64
Weight 2510 lbs 1138.5 kg Max Power 129 HP 96 kW 500 1,893 64 - 80
ADJUSTABLE BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 2.9 Stage FBH BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 2.9 Stage HR SERIES 3
HR SERIES 3 SLICK STABILIZED
Hole
SLICK STABILIZED Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
Hole (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE 1.25 7.57 6.88 3.77 6.81 6.67 7.15
0.39 2.19 1.60 - 1.40 1.54 2.16 1.50 9.15 8.46 5.35 8.55 8.41 8.57
0.78 4.65 4.07 1.45 3.72 3.67 4.29 1.75 10.73 10.04 6.93 10.29 10.16 9.99
1.15 6.99 6.41 3.78 6.38 6.25 6.31 2.00 12.31 11.62 8.51 12.04 11.90 11.41
1.50 9.20 8.62 6.00 8.91 8.77 8.22 2.25 13.89 13.20 10.09 13.78 13.65 13.02
1.83 11.29 10.70 8.08 11.29 11.15 10.53 2.50 15.47 14.78 11.67 15.53 15.39 14.77
2.12 13.12 12.54 9.91 13.38 13.24 12.62
2.38 14.76 14.18 11.56 15.25 15.11 14.49
2.60 16.15 15.57 12.94 16.84 16.70 16.08
2.77 17.22 16.64 14.02 18.06 17.93 17.30
2.90 18.04 17.46 14.84 19.00 18.86 18.24
2.97 18.49 17.90 15.28 19.50 19.37 18.75
3.00 18.67 18.09 15.47 19.72 19.58 18.96
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 153
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.0 Stage HR MUD LUBE
154 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 Lobe 5.0 STAGE HR MUD LUBE 13262
B 180 (17981)
(8136)
1180
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 11165
STAB.) 160 (15138)
10650
(14439) 9770
140 (13246)
450 GPM (1703 LPM) 8375
120
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 100
6980
(9464)
Bit Box Connection 4-1/2 REGULAR 300 GPM (1136 LPM) 5580
70%
UE 1395
Static 355612 lbf 158180 daN 20 RQ (1891)
TO
Max. Overpull for Re-run 432800 lbf 193000 daN 0 0
0 200 400 600 800 1000 1200 1400
Absolute Overpull 721400 lbf 321000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 21.1 in 536 mm
Lobe Configuration 7-8 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 66.7 in 1694 mm
B = Bit to Bend Displacement 0.27 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 54.6 in 1387 mm
Max Differential @ No Load 1,180 psi 8,136 kPa 300 1,136 49 - 80
C = Overall Length 324.2 in 8235 mm Max Torque @ No Load 10,650 ft-lbs 14,439 Nm 450 1,703 93 - 122
Weight 2409 lbs 1092.7 kg Max Power 278 HP 207 kW 600 2,271 137 - 163
ADJUSTABLE BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.0 Stage FBH BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.0 Stage HR SERIES 3
HR SERIES 3 SLICK STABILIZED
Hole
SLICK STABILIZED Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
Hole (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE 1.25 8.15 7.40 4.06 7.35 7.19 7.75
0.39 2.35 1.72 - 1.54 1.70 2.43 1.50 9.85 9.10 5.76 9.24 9.08 9.26
0.78 5.00 4.38 1.56 4.02 3.96 4.69 1.75 11.55 10.80 7.46 11.14 10.98 10.78
1.15 7.52 6.89 4.07 6.92 6.76 6.83 2.00 13.24 12.50 9.16 13.03 12.87 12.29
1.50 9.90 9.27 6.45 9.66 9.50 8.85 2.25 14.94 14.20 10.86 14.92 14.76 14.03
1.83 12.14 11.52 8.70 12.25 12.09 11.36 2.50 16.64 15.90 12.56 16.81 16.65 15.92
2.12 14.12 13.49 10.67 14.52 14.36 13.64
2.38 15.88 15.26 12.43 16.56 16.40 15.67
2.60 17.38 16.75 13.93 18.28 18.12 17.40
2.77 18.53 17.91 15.08 19.62 19.45 18.73
2.90 19.42 18.79 15.97 20.63 20.47 19.75
2.97 19.89 19.26 16.44 21.18 21.02 20.30
3.00 20.10 19.47 16.65 21.42 21.26 20.53
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 155
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage HR MUD LUBE
156 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 7-8 Lobe 5.7 STAGE HR MUD LUBE 18000
B 160 (24405)
(9239)
1340
A (BIT TO BEND)
(BIT TO 14200
STAB.)
140 600 GPM (2271 LPM) (19253)
14000
120 (18982)
450 GPM (1703 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 10000
(13559)
Bit Box Connection 4-1/2 REGULAR 80
300 GPM (1136 LPM)
70%
20 UE 2000
Static 355612 lbf 158180 daN RQ (2712)
TO
Max. Overpull for Re-run 432800 lbf 193000 daN 0 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 721400 lbf 321000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 25000 ft-lbs 33895 Nm
A = Bit To Stabilizer (center) 21.1 in 536 mm
Lobe Configuration 7-8 Lobe 5.7 Stage HR Flow Rate Speed
Adjustable 66.7 in 1694 mm
B = Bit to Bend Displacement 0.23 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 54.6 in 1387 mm
Max Differential @ No Load 1,340 psi 9,239 kPa 300 1,136 53 - 69
C = Overall Length 389.7 in 9898 mm Max Torque @ No Load 14,200 ft-lbs 19,253 Nm 450 1,703 88 - 104
Weight 2827 lbs 1282.3 kg Max Power 331 HP 247 kW 600 2,271 122 - 138
ADJUSTABLE BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage FBH BUILD RATE: 7 in (178 mm) Bottom w/ 6-3/4 (171 mm) 7-8 Lobe 5.7 Stage HR SERIES 3
HR SERIES 3 SLICK STABILIZED
Hole
SLICK STABILIZED Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
Hole (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE 1.25 6.81 6.19 3.40 6.10 5.98 6.37
0.39 1.97 1.44 - 1.23 1.34 1.84 1.50 8.24 7.61 4.82 7.65 7.54 7.67
0.78 4.19 3.66 1.30 3.32 3.29 3.79 1.75 9.66 9.04 6.24 9.20 9.09 8.96
1.15 6.29 5.77 3.41 5.69 5.58 5.64 2.00 11.08 10.46 7.66 10.76 10.65 10.26
1.50 8.28 7.76 5.40 7.94 7.83 7.38 2.25 12.50 11.88 9.08 12.31 12.20 11.70
1.83 10.16 9.63 7.27 10.05 9.94 9.44 2.50 13.92 13.30 10.51 13.87 13.76 13.26
2.12 11.81 11.28 8.92 11.91 11.80 11.30
2.38 13.29 12.76 10.40 13.57 13.46 12.96
2.60 14.54 14.01 11.65 14.98 14.87 14.37
2.77 15.50 14.98 12.62 16.07 15.96 15.46
2.90 16.24 15.72 13.36 16.90 16.79 16.29
2.97 16.64 16.12 13.76 17.35 17.24 16.74
3.00 16.81 16.29 13.93 17.54 17.43 16.93
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 157
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 5-6 Lobe 5.3 Stage HR SERIES 3
158 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 7 in (178 mm) 5-6 Lobe 5.3 STAGE HR SERIES 3
B 250 25000
A (BIT TO BEND) (33896)
(10687)
(BIT TO
1550
STAB.)
200 20000
600 GPM (2271 LPM) (27117)
15600
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 150 15000
(20338)
Bit Box Connection 4-1/2 REGULAR 400 GPM (1515 LPM)
70%
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 250 500 750 1000 1250 1500 1750 2000
Absolute Overpull 742200 lbf 330000 daN (1724) (3558) (5171) (6895) (8619) (10342) (12066) (13790)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 5-6 Lobe 5.3 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.30 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,550 psi 10,687 kPa 200 757 35 - 60
C = Overall Length 366.8 in 9317 mm Max Torque @ No Load 15,600 ft-lbs 21,151 Nm 400 1,514 94 - 120
Weight 2205 lbs 1000.2 kg Max Power 454 HP 339 kW 600 2,271 153 - 180
ADJUSTABLE BUILD RATE: 7 in (178 mm) 5-6 Lobe 5.3 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 5-6 Lobe 5.3 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 2.09 1.54 - 1.02 1.15 1.70 1.25 7.23 6.59 3.69 6.37 6.24 6.39
0.78 4.44 3.90 1.44 3.37 3.25 3.71 1.50 8.74 8.10 5.19 8.05 7.93 7.73
1.15 6.68 6.13 3.67 5.94 5.81 5.62 1.75 10.25 9.60 6.70 9.73 9.61 9.07
1.50 8.79 8.24 5.78 8.37 8.24 7.69 2.00 11.76 11.11 8.21 11.42 11.29 10.74
1.83 10.78 10.23 7.77 10.66 10.54 9.98 2.25 13.27 12.62 9.72 13.10 12.98 12.42
2.12 12.53 11.98 9.52 12.67 12.55 11.99 2.50 14.77 14.13 11.22 14.78 14.66 14.11
2.38 14.10 13.55 11.09 14.48 14.35 13.80
2.60 15.42 14.88 12.41 16.00 15.88 15.32
2.77 16.45 15.90 13.44 17.18 17.06 16.50
2.90 17.23 16.68 14.22 18.08 17.96 17.40
2.97 17.65 17.11 14.64 18.57 18.45 17.89
3.00 17.83 17.29 14.82 18.78 18.65 18.10
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 159
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 5-6 Lobe 8.1 Stage HR SERIES 3
160 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 7 in (178 mm) 5-6 Lobe 8.1 STAGE HR SERIES 3
B 350
(12570)
A (BIT TO BEND)
1820
(BIT TO
STAB.) 12000
700 GPM (2649 LPM) (16270)
280 11590
600 GPM (2271 LPM) (15710)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 210 500 GPM (1892 LPM)
70%
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 400 800 1200 1600 2000
Absolute Overpull 742200 lbf 330000 daN (1724) (3558) (5171) (6895) (10342)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 5-6 Lobe 8.1 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.41 rev/gal 0.11 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,820 psi 12,548 kPa 500 1,893 112 - 205
C = Overall Length 391 in 9931 mm Max Torque @ No Load 11,590 ft-lbs 15,714 Nm 600 2,271 156 - 248
Weight 3212 lbs 1456.9 kg Max Power 441 HP 329 kW 700 2,650 200 - 290
ADJUSTABLE BUILD RATE: 7 in (178 mm) 5-6 Lobe 8.1 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 5-6 Lobe 8.1 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.97 1.45 - 0.94 1.05 1.54 1.25 6.80 6.19 3.46 5.96 5.85 5.98
0.78 4.18 3.66 1.35 3.15 3.04 3.45 1.50 8.22 7.61 4.88 7.53 7.42 7.25
1.15 6.28 5.76 3.45 5.54 5.43 5.26 1.75 9.63 9.03 6.30 9.10 8.99 8.52
1.50 8.26 7.75 5.43 7.81 7.70 7.21 2.00 11.05 10.44 7.72 10.67 10.56 10.08
1.83 10.13 9.62 7.30 9.94 9.83 9.35 2.25 12.47 11.86 9.13 12.24 12.14 11.65
2.12 11.77 11.26 8.95 11.82 11.71 11.22 2.50 13.88 13.28 10.55 13.82 13.71 13.22
2.38 13.25 12.73 10.42 13.50 13.39 12.90
2.60 14.49 13.98 11.67 14.92 14.81 14.33
2.77 15.46 14.94 12.63 16.02 15.91 15.43
2.90 16.19 15.68 13.37 16.86 16.75 16.27
2.97 16.59 16.08 13.76 17.31 17.21 16.72
3.00 16.76 16.25 13.93 17.51 17.40 16.91
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 161
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 6-7 Lobe 6.5 Stage HR SERIES 3
162 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 7 in (178 mm) 6-7 Lobe 6.5 STAGE HR SERIES 3
B 200 20000
(10549)
(27117)
1530
A (BIT TO BEND)
(BIT TO
STAB.) 180 750 GPM (2839 LPM) 16690
(22629)
160 16000
(21693)
140 575 GPM (2177 LPM)
70%
UE
Static 509765 lbf 226750 daN 20 RQ
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 200 400 600 800 1000 1200 1400 1600 1800
Absolute Overpull 742200 lbf 330000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032) (12411)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 6-7 Lobe 6.5 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.23 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,530 psi 10,549 kPa 400 1,514 73 - 90
C = Overall Length 406 in 10312 mm Max Torque @ No Load 16,690 ft-lbs 22,629 Nm 575 2,177 113 - 130
Weight 2655 lbs 1204.3 kg Max Power 486 HP 363 kW 750 2,839 153 - 170
ADJUSTABLE BUILD RATE: 7 in (178 mm) 6-7 Lobe 6.5 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 6-7 Lobe 6.5 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.89 1.40 - 0.90 1.00 1.45 1.25 6.55 5.97 3.34 5.73 5.63 5.75
0.78 4.03 3.53 1.30 3.03 2.93 3.31 1.50 7.92 7.34 4.71 7.24 7.14 6.98
1.15 6.05 5.55 3.32 5.32 5.22 5.06 1.75 9.29 8.70 6.07 8.75 8.65 8.21
1.50 7.96 7.47 5.24 7.50 7.40 6.94 2.00 10.65 10.07 7.44 10.26 10.16 9.71
1.83 9.77 9.27 7.04 9.55 9.44 8.99 2.25 12.02 11.43 8.80 11.77 11.67 11.21
2.12 11.35 10.86 8.62 11.35 11.24 10.79 2.50 13.38 12.80 10.17 13.28 13.18 12.72
2.38 12.77 12.28 10.05 12.96 12.86 12.41
2.60 13.97 13.48 11.25 14.32 14.22 13.77
2.77 14.90 14.41 12.18 15.38 15.28 14.83
2.90 15.61 15.12 12.89 16.18 16.08 15.63
2.97 15.99 15.50 13.27 16.62 16.52 16.07
3.00 16.16 15.66 13.43 16.81 16.70 16.25
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 163
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 6-7 Lobe 8.4 Stage HR SERIES 3
164 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 7 in (178 mm) 6-7 Lobe 8.4 STAGE HR SERIES 3 20000
B 250
(27116)
(13652)
A (BIT TO BEND)
1980
(BIT TO 750 GPM (2839 LPM)
16550
STAB.)
(22439)
200 16000
(21693)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 150
(16270)
Bit Box Connection 4-1/2 REGULAR
70%
UE (5423)
Static 509765 lbf 226750 daN RQ
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 500 1000 1500 2000 2500
Absolute Overpull 742200 lbf 330000 daN (3447) (6895) (10342) (13790) (17237)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 6-7 Lobe 8.4 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.30 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,980 psi 13,652 kPa 350 1,325 80 - 110
C = Overall Length 406 in 10312 mm Max Torque @ No Load 16,550 ft-lbs 22,439 Nm 550 2,082 140 - 170
Weight 2655 lbs 1204.3 kg Max Power 630 HP 470 kW 750 2,839 200 - 230
ADJUSTABLE BUILD RATE: 7 in (178 mm) 6-7 Lobe 8.4 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 6-7 Lobe 8.4 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.89 1.40 - 0.90 1.00 1.45 1.25 6.55 5.97 3.34 5.73 5.63 5.75
0.78 4.03 3.53 1.30 3.03 2.93 3.31 1.50 7.92 7.34 4.71 7.24 7.14 6.98
1.15 6.05 5.55 3.32 5.32 5.22 5.06 1.75 9.29 8.70 6.07 8.75 8.65 8.21
1.50 7.96 7.47 5.24 7.50 7.40 6.94 2.00 10.65 10.07 7.44 10.26 10.16 9.71
1.83 9.77 9.27 7.04 9.55 9.44 8.99 2.25 12.02 11.43 8.80 11.77 11.67 11.21
2.12 11.35 10.86 8.62 11.35 11.24 10.79 2.50 13.38 12.80 10.17 13.28 13.18 12.72
2.38 12.77 12.28 10.05 12.96 12.86 12.41
2.60 13.97 13.48 11.25 14.32 14.22 13.77
2.77 14.90 14.41 12.18 15.38 15.28 14.83
2.90 15.61 15.12 12.89 16.18 16.08 15.63
2.97 15.99 15.50 13.27 16.62 16.52 16.07
3.00 16.16 15.66 13.43 16.81 16.70 16.25
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 165
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 6-7 Lobe 11.4 Stage HR SERIES 3
166 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 7 in (178 mm) 6-7 Lobe 11.4 STAGE HR SERIES 3 20000
B 350
(27117)
(18478)
A (BIT TO BEND)
2680
(BIT TO 750 GPM (2840 LPM) 16350
STAB.) (22168)
300
16000
(21693)
250 550 GPM (2082 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 200 (16270)
70%
50 UE
Static 509765 lbf 226750 daN RQ
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 500 1000 1500 2000 2500 3000 3500
Absolute Overpull 742200 lbf 330000 daN (3448) (6895) (10343) (13790) (17237) (20685) (24132)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 6-7 Lobe 11.4 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.42 rev/gal 0.11 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 2,680 psi 18,478 kPa 350 1,325 120 - 150
C = Overall Length 406 in 10312 mm Max Torque @ No Load 16,350 ft-lbs 22,168 Nm 550 2,082 200 - 235
Weight 2623 lbs 1189.8 kg Max Power 872 HP 650 kW 750 2,839 280 - 320
ADJUSTABLE BUILD RATE: 7 in (178 mm) 6-7 Lobe 11.4 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 6-7 Lobe 11.4 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.89 1.40 - 0.90 1.00 1.45 1.25 6.55 5.97 3.34 5.73 5.63 5.75
0.78 4.03 3.53 1.30 3.03 2.93 3.31 1.50 7.92 7.34 4.71 7.24 7.14 6.98
1.15 6.05 5.55 3.32 5.32 5.22 5.06 1.75 9.29 8.70 6.07 8.75 8.65 8.21
1.50 7.96 7.47 5.24 7.50 7.40 6.94 2.00 10.65 10.07 7.44 10.26 10.16 9.71
1.83 9.77 9.27 7.04 9.55 9.44 8.99 2.25 12.02 11.43 8.80 11.77 11.67 11.21
2.12 11.35 10.86 8.62 11.35 11.24 10.79 2.50 13.38 12.80 10.17 13.28 13.18 12.72
2.38 12.77 12.28 10.05 12.96 12.86 12.41
2.60 13.97 13.48 11.25 14.32 14.22 13.77
2.77 14.90 14.41 12.18 15.38 15.28 14.83
2.90 15.61 15.12 12.89 16.18 16.08 15.63
2.97 15.99 15.50 13.27 16.62 16.52 16.07
3.00 16.16 15.66 13.43 16.81 16.70 16.25
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 167
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 7-8 Lobe 8.5 Stage HR SERIES 3
168 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 7 in (178 mm) 7-8 Lobe 8.5 STAGE HR SERIES 3
B 250
(13190)
A (BIT TO BEND)
1910
(BIT TO
STAB.) 20000
(27117)
200 750 GPM (2840 LPM)
18710
(25368)
625 GPM (2366 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 500 GPM (1893 LPM)
Bit Box Connection 4-1/2 REGULAR
70%
Static 509765 lbf 226750 daN RQ
UE
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 400 800 1200 1600 2000
Absolute Overpull 742200 lbf 330000 daN (2758) (5516) (8274) (11032) (13790)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 7-8 Lobe 8.5 Stage HR Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.26 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 1,910 psi 13,169 kPa 500 1,893 100 - 130
C = Overall Length 431 in 10947 mm Max Torque @ No Load 18,710 ft-lbs 25,367 Nm 625 2,366 135 - 165
Weight 2976 lbs 1349.9 kg Max Power 606 HP 452 kW 750 2,839 170 - 200
ADJUSTABLE BUILD RATE: 7 in (178 mm) 7-8 Lobe 8.5 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 7-8 Lobe 8.5 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 1.79 1.32 - 0.84 0.93 1.33 1.25 6.18 5.63 3.15 5.39 5.30 5.40
0.78 3.80 3.33 1.23 2.84 2.75 3.09 1.50 7.47 6.92 4.44 6.80 6.71 6.57
1.15 5.71 5.24 3.14 4.99 4.91 4.76 1.75 8.76 8.21 5.73 8.22 8.13 7.74
1.50 7.51 7.04 4.94 7.03 6.94 6.54 2.00 10.05 9.50 7.02 9.63 9.55 9.14
1.83 9.21 8.75 6.64 8.95 8.86 8.46 2.25 11.34 10.79 8.31 11.05 10.96 10.56
2.12 10.71 10.24 8.14 10.64 10.55 10.14 2.50 12.63 12.08 9.59 12.47 12.38 11.98
2.38 12.05 11.58 9.48 12.15 12.06 11.66
2.60 13.18 12.72 10.61 13.43 13.34 12.93
2.77 14.06 13.59 11.49 14.41 14.32 13.92
2.90 14.73 14.26 12.16 15.17 15.08 14.68
2.97 15.09 14.62 12.52 15.58 15.49 15.08
3.00 15.24 14.78 12.67 15.75 15.66 15.26
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 169
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
7 in (178 mm) 9-10 Lobe 8.0 Stage HR SERIES 3
170 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 6-3/4 in (171 mm) 9-10 Lobe 8.0 STAGE HR SERIES 3 20000
B 200 (27117)
(13790)
A 700 GPM (2650 LPM)
2000
(BIT TO BEND)
(BIT TO 18155
STAB.) 180 (24615)
600 GPM (2271 LPM) 16000
160
(21693)
140 500 GPM (1893 LPM)
SPEED (RPM)
Bit Size Range 8-1/2 - 9-7/8 in 216 - 251 mm 120 (16270)
400 GPM (1514 LPM)
Bit Box Connection 4-1/2 REGULAR 100
Dynamic 4000
151925 lbf 67580 daN 40 (5423)
Bearing Load - Off Bottom
70%
UE
Static 509765 lbf 226750 daN 20 RQ
TO
Max. Overpull for Re-run 509765 lbf 227000 daN 0
0 500 1000 1500 2000 2500
Absolute Overpull 742200 lbf 330000 daN (3448) (6895) (10343) (13790) (17237)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 32000 ft-lbs 43386 Nm
A = Bit To Stabilizer (center) 16 in 406 mm
Lobe Configuration 9-10 Lobe 8.0 Stage Flow Rate Speed
Adjustable 68 in 1727 mm
B = Bit to Bend Displacement 0.27 rev/gal 0.07 rev/l GPM LPM RPM
Fixed 56 in 1422 mm
Max Differential @ No Load 2,000 psi 13,790 kPa 400 1,514 80 - 108
C = Overall Length 391 in 9931 mm Max Torque @ No Load 18,155 ft-lbs 24,615 Nm 550 2,082 120 - 148
Weight 2595 lbs 1177.1 kg Max Power 553 HP 412 kW 700 2,650 160 - 188
ADJUSTABLE BUILD RATE: 7 in (178 mm) 9-10 Lobe 8.0 Stage HR SERIES 3 FBH BUILD RATE: 7 in (178 mm) 9-10 Lobe 8.0 Stage HR SERIES 3
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8 Size 8-1/2 8-3/4 9-7/8 8-1/2 8-3/4 9-7/8
(216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm) (216 mm) (222 mm) (251 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 0.39 1.97 1.45 0.94 1.05 1.54 1.25 6.80 6.19 3.46 5.96 5.85 5.98
0.78 0.78 4.18 3.66 3.15 3.04 3.45 1.50 8.22 7.61 4.88 7.53 7.42 7.25
1.15 1.15 6.28 5.76 5.54 5.43 5.26 1.75 9.63 9.03 6.30 9.10 8.99 8.52
1.50 1.50 8.26 7.75 7.81 7.70 7.21 2.00 11.05 10.44 7.72 10.67 10.56 10.08
1.83 1.83 10.13 9.62 9.94 9.83 9.35 2.25 12.47 11.86 9.13 12.24 12.14 11.65
2.12 2.12 11.77 11.26 11.82 11.71 11.22 2.50 13.88 13.28 10.55 13.82 13.71 13.22
2.38 2.38 13.25 12.73 13.50 13.39 12.90
2.60 2.60 14.49 13.98 14.92 14.81 14.33
2.77 2.77 15.46 14.94 16.02 15.91 15.43
2.90 2.90 16.19 15.68 16.86 16.75 16.27
2.97 2.97 16.59 16.08 17.31 17.21 16.72
3.00 3.00 16.76 16.25 17.51 17.40 16.91
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 171
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 1
172 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 4-5 Lobe 5.3 STAGE HR SERIES 1
B 270
(8618)
1250
A (BIT TO BEND)
(BIT TO 16000
STAB.) 240 (21693)
900 GPM (3407 LPM) 13620
210 (18466)
12000
180
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 150 600 GPM (2271 LPM)
70%
UE
Static 573485 lbf 255100 daN 30 RQ
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 4-5 Lobe 5.3 Stage HR Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.24 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 1,250 psi 8,618 kPa 300 1,136 50 - 72
C = Overall Length 380.7 in 9670 mm Max Torque @ No Load 13,620 ft-lbs 18,466 Nm 600 2,271 122 - 144
Weight 4378.2 lbs 1985.9 kg Max Power 503 HP 375 kW 900 3,407 194 - 216
ADJUSTABLE BUILD RATE: 8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 1 FBH BUILD RATE: 8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.14 1.49 2.24 1.25 4.31 2.83 - 6.17 5.85 6.60
0.78 2.02 0.76 - 3.21 3.33 4.08 1.50 5.76 4.28 1.07 7.83 7.49 7.84
1.15 4.16 2.90 0.17 5.76 5.42 5.83 1.75 7.21 5.73 2.52 9.50 9.16 9.08
1.50 6.20 4.94 2.21 8.18 7.83 7.49 2.00 8.66 7.18 3.97 11.17 10.82 10.32
1.83 8.11 6.85 4.12 10.46 10.11 9.36 2.25 10.11 8.63 5.42 12.84 12.49 11.74
2.12 9.79 8.53 5.80 12.46 12.12 11.37 2.50 11.56 10.08 6.87 14.50 14.16 13.41
2.38 11.30 10.04 7.31 14.26 13.91 13.16
2.60 12.58 11.32 8.59 15.77 15.43 14.68
2.77 13.56 12.30 9.57 16.95 16.60 15.85
2.90 14.32 13.06 10.33 17.85 17.50 16.75
2.97 14.72 13.46 10.73 18.33 17.98 17.23
3.00 14.90 13.64 10.91 18.54 18.19 17.44
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 173
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 5-6 Lobe 3.0 Stage SERIES 1
174 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 5-6 Lobe 3.0 STAGE HR SERIES 1
B 200 5000
A (BIT TO BEND) (6779)
(1979)
(BIT TO 900 GPM (3407 LPM)
287
STAB.) 180 4082
(5534)
160 4000
(5423)
140 700 GPM (2650 LPM)
70%
Bearing Load - Off Bottom (1356)
RQ
Static 573485 lbf 255100 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.77 2.49 4.07 1.25 6.12 4.02 - 8.88 8.26 9.83
0.78 2.87 1.08 - 4.50 4.83 6.40 1.50 8.19 6.08 1.52 11.40 10.67 11.45
1.15 5.92 4.13 0.25 8.41 7.68 8.61 1.75 10.25 8.15 3.59 13.91 13.19 13.07
1.50 8.81 7.02 3.14 12.11 11.38 10.71 2.00 12.31 10.21 5.65 16.43 15.70 14.69
1.83 11.53 9.74 5.86 15.59 14.86 13.29 2.25 14.37 12.27 7.71 18.94 18.22 16.65
2.12 13.93 12.13 8.25 18.65 17.92 16.35 2.50 16.44 14.33 9.77 21.46 20.73 19.16
2.38 16.07 14.28 10.40 21.39 20.67 19.10
2.60 17.88 16.09 12.21 23.71 22.99 21.42
2.77 19.29 17.49 13.61 25.51 24.78 23.21
2.90 20.36 18.57 14.68 26.88 26.15 24.58
2.97 20.93 19.14 15.26 27.62 26.89 25.32
3.00 21.18 19.39 15.51 27.93 27.21 25.64
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 175
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 5-6 Lobe 3.0 Stage HR SERIES 1
176 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 5-6 Lobe 3.0 STAGE HR SERIES 1
B 200 8000
A (BIT TO BEND) (10846)
(2972)
(BIT TO 900 GPM (3407 LPM)
431
STAB.) 180
6123
(8302)
160
6000
140 700 GPM (2650 LPM) (8135)
70%
Bearing Load - Off Bottom UE
RQ
Static 573485 lbf 255100 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.77 2.49 4.07 1.25 6.12 4.02 - 8.88 8.26 9.83
0.78 2.87 1.08 - 4.50 4.83 6.40 1.50 8.19 6.08 1.52 11.40 10.67 11.45
1.15 5.92 4.13 0.25 8.41 7.68 8.61 1.75 10.25 8.15 3.59 13.91 13.19 13.07
1.50 8.81 7.02 3.14 12.11 11.38 10.71 2.00 12.31 10.21 5.65 16.43 15.70 14.69
1.83 11.53 9.74 5.86 15.59 14.86 13.29 2.25 14.37 12.27 7.71 18.94 18.22 16.65
2.12 13.93 12.13 8.25 18.65 17.92 16.35 2.50 16.44 14.33 9.77 21.46 20.73 19.16
2.38 16.07 14.28 10.40 21.39 20.67 19.10
2.60 17.88 16.09 12.21 23.71 22.99 21.42
2.77 19.29 17.49 13.61 25.51 24.78 23.21
2.90 20.36 18.57 14.68 26.88 26.15 24.58
2.97 20.93 19.14 15.26 27.62 26.89 25.32
3.00 21.18 19.39 15.51 27.93 27.21 25.64
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 177
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 1
178 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE SERIES 1
B 180 10000
(4599)
A (13558)
667
(BIT TO BEND)
(BIT TO 900 GPM (3407 LPM)
STAB.) 160 8793
(11922)
8000
140 (10846)
120
SPEED (RPM)
6000
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100 (8135)
Bit Box Connection 6-5/8 REGULAR
70%
Bearing Load - Off Bottom (2712)
UE
Static 573485 lbf 255100 daN 20 RQ
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 923500 lbf 411000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 6-7 Lobe 4.0 Stage Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 600 psi 4,137 kPa 300 1,136 51 - 68
C = Overall Length 358.7 in 9111 mm Max Torque @ No Load 8,820 ft-lbs 11,958 Nm 600 2,271 94 - 111
Weight 4003.2 lbs 1815.8 kg Max Power 228 HP 170 kW 900 3,407 136 - 153
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 1 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.62 2.46 1.25 4.56 3.00 - 6.55 6.19 7.04
0.78 2.14 0.80 - 3.39 3.54 4.39 1.50 6.10 4.53 1.14 8.33 7.94 8.34
1.15 4.41 3.08 0.18 6.13 5.74 6.21 1.75 7.64 6.07 2.67 10.11 9.72 9.64
1.50 6.56 5.23 2.34 8.72 8.32 7.94 2.00 9.17 7.61 4.21 11.89 11.50 10.94
1.83 8.59 7.26 4.37 11.15 10.76 9.92 2.25 10.71 9.14 5.75 13.67 13.28 12.43
2.12 10.38 9.04 6.15 13.30 12.91 12.06 2.50 12.25 10.68 7.28 15.45 15.06 14.22
2.38 11.97 10.64 7.75 15.22 14.83 13.98
2.60 13.33 11.99 9.10 16.84 16.45 15.61
2.77 14.37 13.03 10.14 18.10 17.71 16.86
2.90 15.17 13.83 10.94 19.06 18.67 17.82
2.97 15.60 14.26 11.37 19.58 19.19 18.34
3.00 15.78 14.45 11.56 19.80 19.41 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 179
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1
180 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE HR SERIES 1
B 180 13820
A (BIT TO BEND) (18737)
(6481)
(BIT TO
940
STAB.) 160 900 GPM (3407 LPM) 16000
(21693)
140 14000
(18981)
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100 10000
(13558)
Bit Box Connection 6-5/8 REGULAR
70%
(5423)
Bearing Load - Off Bottom UE
Static 573485 lbf 255100 daN 20 RQ 2000
TO (2712)
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 6-7 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 940 psi 6,481 kPa 500 1,893 51 - 68
C = Overall Length 358.7 in 9111 mm Max Torque @ No Load 13,820 ft-lbs 18,737 Nm 700 2,650 94 - 111
Weight 4025.2 lbs 1825.8 kg Max Power 358 HP 267 kW 900 3,407 136 - 153
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.62 2.46 1.25 4.56 3.00 - 6.55 6.19 7.04
0.78 2.14 0.80 - 3.39 3.54 4.39 1.50 6.10 4.53 1.14 8.33 7.94 8.34
1.15 4.41 3.08 0.18 6.13 5.74 6.21 1.75 7.64 6.07 2.67 10.11 9.72 9.64
1.50 6.56 5.23 2.34 8.72 8.32 7.94 2.00 9.17 7.61 4.21 11.89 11.50 10.94
1.83 8.59 7.26 4.37 11.15 10.76 9.92 2.25 10.71 9.14 5.75 13.67 13.28 12.43
2.12 10.38 9.04 6.15 13.30 12.91 12.06 2.50 12.25 10.68 7.28 15.45 15.06 14.22
2.38 11.97 10.64 7.75 15.22 14.83 13.98
2.60 13.33 11.99 9.10 16.84 16.45 15.61
2.77 14.37 13.03 10.14 18.10 17.71 16.86
2.90 15.17 13.83 10.94 19.06 18.67 17.82
2.97 15.60 14.26 11.37 19.58 19.19 18.34
3.00 15.78 14.45 11.56 19.80 19.41 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 181
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 1
182 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 5.0 STAGE SERIES 1
B 200 12000
A (BIT TO BEND) (16270)
(BIT TO 11152
STAB.)
900 GPM (3407 LPM) (15120)
10000
(5792)
840
(13558)
150
8000
SPEED (RPM)
600 GPM (2271 LPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
100 6000
Bit Box Connection 6-5/8 REGULAR
70%
RQ (2712)
Static 573485 lbf 255100 daN TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 6-7 Lobe 5.0 Stage Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 840 psi 5,792 kPa 300 1,136 28 - 51
C = Overall Length 402.7 in 10229 mm Max Torque @ No Load 11,152 ft-lbs 15,120 Nm 600 2,271 83 - 106
Weight 4438.2 lbs 2013.1 kg Max Power 291 HP 217 kW 900 3,407 137 - 160
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 1 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.07 1.38 2.05 1.25 4.08 2.68 - 5.83 5.55 6.21
0.78 1.91 0.72 - 3.04 3.15 3.82 1.50 5.45 4.05 1.02 7.40 7.09 7.40
1.15 3.94 2.75 0.17 5.44 5.13 5.50 1.75 6.83 5.43 2.39 8.96 8.66 8.59
1.50 5.87 4.67 2.09 7.71 7.40 7.08 2.00 8.20 6.80 3.76 10.53 10.22 9.77
1.83 7.68 6.49 3.90 9.84 9.54 8.87 2.25 9.57 8.17 5.14 12.10 11.79 11.12
2.12 9.27 8.08 5.50 11.72 11.41 10.75 2.50 10.95 9.55 6.51 13.67 13.36 12.69
2.38 10.70 9.51 6.92 13.41 13.10 12.43
2.60 11.91 10.72 8.13 14.83 14.52 13.86
2.77 12.84 11.65 9.07 15.93 15.62 14.96
2.90 13.56 12.37 9.78 16.78 16.47 15.80
2.97 13.94 12.75 10.16 17.23 16.92 16.25
3.00 14.11 12.91 10.33 17.42 17.11 16.45
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 183
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 1
184 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 5.0 STAGE HR SERIES 1
B 200 18000
A (BIT TO BEND) (24404)
(BIT TO 17076
STAB.) 16000 (23152)
(8688)
900 GPM (3407 LPM) (21693)
1260
14000
150 (18981)
12000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 600 GPM (2271 LPM)
10000
100 (13558)
Bit Box Connection 6-5/8 REGULAR
70%
Static 573485 lbf 255100 daN RQ 2000
TO (2712)
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000 1200 1400
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 6-7 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 1,260 psi 8,687 kPa 300 1,136 28 - 51
C = Overall Length 402.7 in 10229 mm Max Torque @ No Load 17,076 ft-lbs 23,152 Nm 600 2,271 83 - 106
Weight 4440.2 lbs 2014 kg Max Power 445 HP 332 kW 900 3,407 137 - 160
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 1 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.07 1.38 2.05 1.25 4.08 2.68 - 5.83 5.55 6.21
0.78 1.91 0.72 - 3.04 3.15 3.82 1.50 5.45 4.05 1.02 7.40 7.09 7.40
1.15 3.94 2.75 0.17 5.44 5.13 5.50 1.75 6.83 5.43 2.39 8.96 8.66 8.59
1.50 5.87 4.67 2.09 7.71 7.40 7.08 2.00 8.20 6.80 3.76 10.53 10.22 9.77
1.83 7.68 6.49 3.90 9.84 9.54 8.87 2.25 9.57 8.17 5.14 12.10 11.79 11.12
2.12 9.27 8.08 5.50 11.72 11.41 10.75 2.50 10.95 9.55 6.51 13.67 13.36 12.69
2.38 10.70 9.51 6.92 13.41 13.10 12.43
2.60 11.91 10.72 8.13 14.83 14.52 13.86
2.77 12.84 11.65 9.07 15.93 15.62 14.96
2.90 13.56 12.37 9.78 16.78 16.47 15.80
2.97 13.94 12.75 10.16 17.23 16.92 16.25
3.00 14.11 12.91 10.33 17.42 17.11 16.45
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 185
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 1
186 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 2.0 STAGE SERIES 1
B 96 8000
(2579)
A (BIT TO BEND) 900 GPM (3407 LPM) (10846)
374
(BIT TO
STAB.) 7100
84
(9626)
72 6000
600 GPM (2271 LPM) (8135)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
48 300 GPM (1136 LPM) 4000
Bit Box Connection 6-5/8 REGULAR (5423)
70%
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 923500 lbf 411000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 7-8 Lobe 2.0 Stage Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.29 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 374 psi 2,579 kPa 300 1,136 33 - 44
C = Overall Length 320.7 in 8146 mm Max Torque @ No Load 7,100 ft-lbs 9,626 Nm 600 2,271 55 - 64
Weight 3774.2 lbs 1711.9 kg Max Power 104 HP 78 kW 900 3,407 77 - 84
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 1 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.40 1.89 2.95 1.25 5.08 3.34 - 7.32 6.89 7.95
0.78 2.38 0.89 - 3.77 3.97 5.03 1.50 6.80 5.05 1.27 9.34 8.85 9.36
1.15 4.92 3.43 0.21 6.88 6.39 7.00 1.75 8.51 6.76 2.98 11.36 10.87 10.77
1.50 7.31 5.83 2.60 9.82 9.33 8.86 2.00 10.22 8.47 4.69 13.38 12.89 12.19
1.83 9.57 8.09 4.86 12.60 12.11 11.05 2.25 11.93 10.19 6.40 15.40 14.91 13.85
2.12 11.56 10.07 6.85 15.04 14.55 13.49 2.50 13.65 11.90 8.11 17.41 16.92 15.86
2.38 13.34 11.85 8.63 17.22 16.73 15.67
2.60 14.85 13.36 10.14 19.07 18.58 17.52
2.77 16.01 14.52 11.30 20.50 20.01 18.95
2.90 16.90 15.41 12.19 21.59 21.10 20.04
2.97 17.38 15.89 12.67 22.18 21.69 20.63
3.00 17.58 16.10 12.88 22.43 21.94 20.88
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 187
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 1
188 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE SERIES 1
B 160 6000
A (BIT TO BEND) 900 GPM (3407 LPM) (8135)
(BIT TO 5285
STAB.) 140 (7165)
5000
(6779)
120
(2255)
327
4000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
80 3000
Bit Box Connection 6-5/8 REGULAR (4067)
70%
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 923500 lbf 411000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 7-8 Lobe 3.0 Stage Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 327 psi 2,255 kPa 300 1,136 21 - 48
C = Overall Length 312.7 in 7943 mm Max Torque @ No Load 5,285 ft-lbs 7,165 Nm 600 2,271 71 - 97
Weight 3826.2 lbs 1735.5 kg Max Power 121 HP 90 kW 900 3,407 120 - 146
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 1 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.44 1.96 3.07 1.25 5.21 3.42 - 7.51 7.05 8.17
0.78 2.44 0.92 - 3.86 4.07 5.18 1.50 6.96 5.17 1.30 9.59 9.07 9.61
1.15 5.04 3.51 0.21 7.06 6.55 7.19 1.75 8.72 6.93 3.05 11.66 11.15 11.05
1.50 7.49 5.97 2.67 10.09 9.58 9.08 2.00 10.47 8.68 4.81 13.74 13.22 12.49
1.83 9.81 8.29 4.98 12.95 12.44 11.32 2.25 12.23 10.44 6.56 15.82 15.30 14.18
2.12 11.85 10.32 7.02 15.46 14.95 13.83 2.50 13.98 12.19 8.31 17.89 17.38 16.26
2.38 13.67 12.15 8.84 17.71 17.20 16.08
2.60 15.21 13.69 10.39 19.62 19.10 17.98
2.77 16.41 14.88 11.58 21.09 20.57 19.46
2.90 17.32 15.79 12.49 22.21 21.70 20.58
2.97 17.81 16.28 12.98 22.82 22.30 21.19
3.00 18.02 16.49 13.19 23.08 22.56 21.45
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 189
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 1
190 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE HR SERIES 1 13280
B 160 (18005)
(4895)
A (BIT TO BEND)
900 GPM (3407 LPM)
710
(BIT TO
STAB.) 11620
140 (15755)
11140
(15104)
9960
120 (13504)
650 GPM (2461 LPM)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
6640
80
Bit Box Connection 6-5/8 REGULAR (9003)
70%
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 7-8 Lobe 3.0 Stage HR Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 491 psi 3,385 kPa 300 1,136 21 - 48
C = Overall Length 312.7 in 7943 mm Max Torque @ No Load 7,928 ft-lbs 10,749 Nm 600 2,271 71 - 97
Weight 3484 lbs 1580.3 kg Max Power 181 HP 135 kW 900 3,407 120 - 146
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 1 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.44 1.96 3.07 1.25 5.21 3.42 - 7.51 7.05 8.17
0.78 2.44 0.92 - 3.86 4.07 5.18 1.50 6.96 5.17 1.30 9.59 9.07 9.61
1.15 5.04 3.51 0.21 7.06 6.55 7.19 1.75 8.72 6.93 3.05 11.66 11.15 11.05
1.50 7.49 5.97 2.67 10.09 9.58 9.08 2.00 10.47 8.68 4.81 13.74 13.22 12.49
1.83 9.81 8.29 4.98 12.95 12.44 11.32 2.25 12.23 10.44 6.56 15.82 15.30 14.18
2.12 11.85 10.32 7.02 15.46 14.95 13.83 2.50 13.98 12.19 8.31 17.89 17.38 16.26
2.38 13.67 12.15 8.84 17.71 17.20 16.08
2.60 15.21 13.69 10.39 19.62 19.10 17.98
2.77 16.41 14.88 11.58 21.09 20.57 19.46
2.90 17.32 15.79 12.49 22.21 21.70 20.58
2.97 17.81 16.28 12.98 22.82 22.30 21.19
3.00 18.02 16.49 13.19 23.08 22.56 21.45
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 191
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1
192 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.4 STAGE HR SERIES 1 22530
B 90 (30547)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 25000
STAB.) 80 (33895)
(5516)
70
800
20000
(27116)
60 450 GPM (1703 LPM)
70%
(6779)
Static 573485 lbf 255100 daN 10
TO
RQ
0
Max. Overpull for Re-run 554100 lbf 246000 daN 0 100 200 300 400 500 600 700 800 900 1000
(690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6506) (6895)
Absolute Overpull 923500 lbf 411000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 7-8 Lobe 3.4 Stage HR Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.09 rev/gal 0.02 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 800 psi 5,516 kPa 400 1,514 27 - 36
C = Overall Length 452.7 in 11499 mm Max Torque @ No Load 22,530 ft-lbs 30,547 Nm 650 2,461 50 - 59
Weight 5180.2 lbs 2349.7 kg Max Power 309 HP 230 kW 900 3,407 72 - 81
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 0.94 1.18 1.71 1.25 3.64 2.39 - 5.18 4.96 5.48
0.78 1.70 0.64 - 2.71 2.80 3.33 1.50 4.87 3.62 0.91 6.56 6.32 6.56
1.15 3.52 2.45 0.15 4.82 4.57 4.86 1.75 6.09 4.84 2.13 7.94 7.70 7.64
1.50 5.24 4.17 1.86 6.81 6.56 6.31 2.00 7.32 6.07 3.36 9.32 9.08 8.72
1.83 6.85 5.79 3.48 8.68 8.44 7.91 2.25 8.54 7.29 4.58 10.70 10.46 9.93
2.12 8.28 7.21 4.90 10.33 10.09 9.56 2.50 9.77 8.52 5.81 12.08 11.83 11.31
2.38 9.55 8.49 6.18 11.81 11.56 11.04
2.60 10.63 9.56 7.26 13.06 12.81 12.29
2.77 11.46 10.40 8.09 14.02 13.78 13.25
2.90 12.10 11.04 8.73 14.76 14.52 13.99
2.97 12.44 11.38 9.07 15.16 14.92 14.39
3.00 12.59 11.53 9.22 15.33 15.09 14.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 193
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 1
194 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE SERIES 1
B 180 12000
A (BIT TO BEND) (16270)
(BIT TO 900 GPM (3407 LPM)
STAB.) 160 10966
(5075)
(14868)
736
10000
140 (13558)
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100
6000
Bit Box Connection 6-5/8 REGULAR
70%
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 923500 lbf 411000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 7-8 Lobe 4.0 Stage Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 600 psi 4,137 kPa 300 1,136 48 - 64
C = Overall Length 358.7 in 9111 mm Max Torque @ No Load 9,470 ft-lbs 12,840 Nm 600 2,271 88 - 104
Weight 4148.2 lbs 1881.6 kg Max Power 231 HP 172 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 1 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.62 2.46 1.25 4.56 3.00 - 6.55 6.19 7.04
0.78 2.14 0.8 - 3.39 3.54 4.39 1.50 6.10 4.53 1.14 8.33 7.94 8.34
1.15 4.41 3.08 0.18 6.13 5.74 6.21 1.75 7.64 6.07 2.67 10.11 9.72 9.64
1.50 6.56 5.23 2.34 8.72 8.32 7.94 2.00 9.17 7.61 4.21 11.89 11.50 10.94
1.83 8.59 7.26 4.37 11.15 10.76 9.92 2.25 10.71 9.14 5.75 13.67 13.28 12.43
2.12 10.38 9.04 6.15 13.3 12.91 12.06 2.50 12.25 10.68 7.28 15.45 15.06 14.22
2.38 11.97 10.64 7.75 15.22 14.83 13.98
2.60 13.33 11.99 9.10 16.84 16.45 15.61
2.77 14.37 13.03 10.14 18.10 17.71 16.86
2.90 15.17 13.83 10.94 19.06 18.67 17.82
2.97 15.60 14.26 11.37 19.58 19.19 18.34
3.00 15.78 14.45 11.56 19.80 19.41 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 195
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1
196 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE HR SERIES 1
B 180
(6481)
A (BIT TO BEND)
940
(BIT TO 18000
STAB.) 160 (33895)
900 GPM (3407 LPM) 14830
140 (20107)
14000
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100
10000
Bit Box Connection 6-5/8 REGULAR (20337)
70%
TO (6780)
Max. Overpull for Re-run 554100 lbf 246000 daN 0
100 200 300 400 500 600 700 800 900 1000
0
(689) (1379) (2068) (2758) (3447) (4137) (4826) (5516) (6205) (6895)
Absolute Overpull 923500 lbf 411000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 19.26 in 489 mm
Lobe Configuration 7-8 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 87 in 2210 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 72.3 in 1836 mm
Max Differential @ No Load 940 psi 6,481 kPa 300 1,136 48 - 64
C = Overall Length 358.7 in 9111 mm Max Torque @ No Load 14,830 ft-lbs 20,107 Nm 600 2,271 88 - 104
Weight 4148.2 lbs 1881.6 kg Max Power 361 HP 270 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.62 2.46 1.25 4.56 3.00 - 6.55 6.19 7.04
0.78 2.14 0.80 - 3.39 3.54 4.39 1.50 6.10 4.53 1.14 8.33 7.94 8.34
1.15 4.41 3.08 0.18 6.13 5.74 6.21 1.75 7.64 6.07 2.67 10.11 9.72 9.64
1.50 6.56 5.23 2.34 8.72 8.32 7.94 2.00 9.17 7.61 4.21 11.89 11.50 10.94
1.83 8.59 7.26 4.37 11.15 10.76 9.92 2.25 10.71 9.14 5.75 13.67 13.28 12.43
2.12 10.38 9.04 6.15 13.30 12.91 12.06 2.50 12.25 10.68 7.28 15.45 15.06 14.22
2.38 11.97 10.64 7.75 15.22 14.83 13.98
2.60 13.33 11.99 9.10 16.84 16.45 15.61
2.77 14.37 13.03 10.14 18.10 17.71 16.86
2.90 15.17 13.83 10.94 19.06 18.67 17.82
2.97 15.60 14.26 11.37 19.58 19.19 18.34
3.00 15.78 14.45 11.56 19.80 19.41 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 197
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 1
198 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 5.9 STAGE SERIES 1 25966
B 160
A (BIT TO BEND) (35205)
(9584)
1390
(BIT TO
STAB.) 900 GPM (3407 LPM) 22720
140 (30804) 21870
19475 (29652)
120 (26405)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
12980
80
Bit Box Connection 6-5/8 REGULAR (17599)
70%
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 0.94 1.18 1.71 1.25 3.64 2.39 - 5.18 4.96 5.48
0.78 1.70 0.64 - 2.71 2.80 3.33 1.50 4.87 3.62 0.91 6.56 6.32 6.56
1.15 3.52 2.45 0.15 4.82 4.57 4.86 1.75 6.09 4.84 2.13 7.94 7.70 7.64
1.50 5.24 4.17 1.86 6.81 6.56 6.31 2.00 7.32 6.07 3.36 9.32 9.08 8.72
1.83 6.85 5.79 3.48 8.68 8.44 7.91 2.25 8.54 7.29 4.58 10.70 10.46 9.93
2.12 8.28 7.21 4.90 10.33 10.09 9.56 2.50 9.77 8.52 5.81 12.08 11.83 11.31
2.38 9.55 8.49 6.18 11.81 11.56 11.04
2.60 10.63 9.56 7.26 13.06 12.81 12.29
2.77 11.46 10.40 8.09 14.02 13.78 13.25
2.90 12.10 11.04 8.73 14.76 14.52 13.99
2.97 12.44 11.38 9.07 15.16 14.92 14.39
3.00 12.59 11.53 9.22 15.33 15.09 14.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 199
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 2
200 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 4-5 Lobe 5.3 STAGE HR SERIES 2
B 270
(8618)
1250
A (BIT TO BEND)
(BIT TO 16000
STAB.) 240 (21693)
900 GPM (3407 LPM) 13620
210 (18466)
12000
180
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 150 600 GPM (2271 LPM)
70%
UE
Static 573485 lbf 255100 daN 30 RQ
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 4-5 Lobe 5.3 Stage HR Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.24 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 1,250 psi 8,618 kPa 300 1,136 50 - 72
C = Overall Length 368.4 in 9357 mm Max Torque @ No Load 13,620 ft-lbs 18,466 Nm 600 2,271 122 - 144
Weight 4198.2 lbs 1904.3 kg Max Power 503 HP 375 kW 900 3,407 194 - 216
ADJUSTABLE BUILD RATE: 8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 2 FBH BUILD RATE: 8 in (203 mm) 4-5 Lobe 5.3 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.14 1.51 2.30 1.25 3.93 2.15 - 6.06 6.13 6.93
0.78 1.71 0.23 - 3.10 3.46 4.26 1.50 5.43 3.64 - 7.74 7.45 8.24
1.15 3.93 2.45 - 5.66 5.32 6.12 1.75 6.93 5.14 1.27 9.43 9.06 9.56
1.50 6.03 4.54 1.33 8.11 7.74 7.87 2.00 8.42 6.64 2.77 11.11 10.75 10.88
1.83 8.01 6.52 3.30 10.41 10.05 9.53 2.25 9.92 8.14 4.27 12.80 12.43 12.19
2.12 9.74 8.26 5.04 12.44 12.07 11.28 2.50 11.42 9.63 5.76 14.48 14.12 13.51
2.38 11.30 9.81 6.60 14.26 13.89 13.10
2.60 12.62 11.13 7.91 15.79 15.43 14.63
2.77 13.64 12.15 8.93 16.98 16.62 15.82
2.90 14.41 12.93 9.71 17.89 17.52 16.73
2.97 14.83 13.35 10.13 18.38 18.01 17.22
3.00 15.01 13.53 10.31 18.59 18.22 17.43
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 201
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 5-6 Lobe 3.0 Stage SERIES 2
202 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 5-6 Lobe 3.0 STAGE HR SERIES 2
B 200 5000
A (BIT TO BEND) (6779)
(1979)
(BIT TO 900 GPM (3407 LPM)
287
STAB.) 180 4082
(5534)
160 4000
(5423)
140 700 GPM (2650 LPM)
70%
Bearing Load - Off Bottom (1356)
RQ
Static 573485 lbf 255100 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.85 2.64 4.35 1.25 5.67 3.09 - 8.72 8.92 10.64
0.78 2.47 0.33 - 4.39 5.19 6.90 1.50 7.83 5.25 - 11.28 10.69 12.40
1.15 5.67 3.53 - 8.28 7.60 9.31 1.75 9.98 7.41 1.83 13.85 13.05 14.17
1.50 8.69 6.55 1.91 12.05 11.26 11.60 2.00 12.14 9.57 3.99 16.41 15.62 15.93
1.83 11.54 9.40 4.76 15.61 14.82 13.75 2.25 14.30 11.73 6.15 18.97 18.18 17.70
2.12 14.04 11.9 7.26 18.74 17.94 16.23 2.50 16.46 13.89 8.31 21.53 20.74 19.46
2.38 16.29 14.15 9.51 21.54 20.75 19.03
2.60 18.19 16.05 11.41 23.91 23.12 21.40
2.77 19.65 17.51 12.87 25.74 24.95 23.24
2.90 20.78 18.64 14 27.14 26.35 24.64
2.97 21.38 19.24 14.60 27.90 27.11 25.39
3.00 21.64 19.50 14.86 28.22 27.43 25.72
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 203
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 5-6 Lobe 3.0 Stage HR SERIES 2
204 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 5-6 Lobe 3.0 STAGE HR SERIES 2
B 200 8000
A (BIT TO BEND) (10846)
(2972)
(BIT TO 900 GPM (3407 LPM)
431
STAB.) 180
6123
(8302)
160
6000
140 700 GPM (2650 LPM) (8135)
70%
Bearing Load - Off Bottom UE
RQ
Static 573485 lbf 255100 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.85 2.64 4.35 1.25 5.67 3.09 - 8.72 8.92 10.64
0.78 2.47 0.33 - 4.39 5.19 6.90 1.50 7.83 5.25 - 11.28 10.69 12.40
1.15 5.67 3.53 - 8.28 7.60 9.31 1.75 9.98 7.41 1.83 13.85 13.05 14.17
1.50 8.69 6.55 1.91 12.05 11.26 11.60 2.00 12.14 9.57 3.99 16.41 15.62 15.93
1.83 11.54 9.40 4.76 15.61 14.82 13.75 2.25 14.30 11.73 6.15 18.97 18.18 17.70
2.12 14.04 11.90 7.26 18.74 17.94 16.23 2.50 16.46 13.89 8.31 21.53 20.74 19.46
2.38 16.29 14.15 9.51 21.54 20.75 19.03
2.60 18.19 16.05 11.41 23.91 23.12 21.40
2.77 19.65 17.51 12.87 25.74 24.95 23.24
2.90 20.78 18.64 14.00 27.14 26.35 24.64
2.97 21.38 19.24 14.60 27.90 27.11 25.39
3.00 21.64 19.50 14.86 28.22 27.43 25.72
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 205
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 2
206 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE SERIES 2
B 180 10000
(4599)
A (13558)
667
(BIT TO BEND)
(BIT TO 900 GPM (3407 LPM)
STAB.) 160 8793
(11922)
8000
140 (10846)
120
SPEED (RPM)
6000
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100 (8135)
Bit Box Connection 6-5/8 REGULAR
70%
Bearing Load - Off Bottom (2712)
UE
Static 573485 lbf 255100 daN 20 RQ
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 923500 lbf 411000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 6-7 Lobe 4.0 Stage Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 600 psi 4,137 kPa 300 1,136 51 - 68
C = Overall Length 346.4 in 8799 mm Max Torque @ No Load 8,820 ft-lbs 11,958 Nm 600 2,271 94 - 111
Weight 3823.2 lbs 1734.2 kg Max Power 228 HP 170 kW 900 3,407 136 - 153
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 2 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.65 2.55 1.25 4.17 2.28 - 6.43 6.52 7.42
0.78 1.82 0.24 - 3.28 3.70 4.60 1.50 5.76 3.87 - 8.23 7.90 8.80
1.15 4.17 2.60 - 6.02 5.64 6.54 1.75 7.35 5.46 1.35 10.03 9.62 10.19
1.50 6.40 4.82 1.41 8.64 8.23 8.38 2.00 8.94 7.05 2.94 11.83 11.42 11.57
1.83 8.50 6.92 3.50 11.11 10.70 10.11 2.25 10.53 8.64 4.53 13.64 13.22 12.95
2.12 10.34 8.76 5.35 13.29 12.87 11.97 2.50 12.12 10.22 6.12 15.44 15.02 14.34
2.38 11.99 10.42 7.00 15.23 14.82 13.92
2.60 13.39 11.82 8.40 16.88 16.46 15.56
2.77 14.47 12.90 9.48 18.15 17.74 16.84
2.90 15.30 13.72 10.31 19.13 18.71 17.81
2.97 15.74 14.17 10.75 19.65 19.23 18.33
3.00 15.93 14.36 10.94 19.87 19.46 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 207
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 2
208 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE HR SERIES 2
B 180 13820
A (BIT TO BEND) (18737)
(6481)
(BIT TO
940
STAB.) 160 900 GPM (3407 LPM) 16000
(21693)
140 14000
(18981)
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100 10000
(13558)
Bit Box Connection 6-5/8 REGULAR
70%
(5423)
Bearing Load - Off Bottom UE
Static 573485 lbf 255100 daN 20 RQ 2000
TO (2712)
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895) (8274)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.65 2.55 1.25 4.17 2.28 - 6.43 6.52 7.42
0.78 1.82 0.24 - 3.28 3.70 4.60 1.50 5.76 3.87 - 8.23 7.90 8.80
1.15 4.17 2.60 - 6.02 5.64 6.54 1.75 7.35 5.46 1.35 10.03 9.62 10.19
1.50 6.40 4.82 1.41 8.64 8.23 8.38 2.00 8.94 7.05 2.94 11.83 11.42 11.57
1.83 8.50 6.92 3.50 11.11 10.70 10.11 2.25 10.53 8.64 4.53 13.64 13.22 12.95
2.12 10.34 8.76 5.35 13.29 12.87 11.97 2.50 12.12 10.22 6.12 15.44 15.02 14.34
2.38 11.99 10.42 7.00 15.23 14.82 13.92
2.60 13.39 11.82 8.40 16.88 16.46 15.56
2.77 14.47 12.90 9.48 18.15 17.74 16.84
2.90 15.30 13.72 10.31 19.13 18.71 17.81
2.97 15.74 14.17 10.75 19.65 19.23 18.33
3.00 15.93 14.36 10.94 19.87 19.46 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 209
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 2
210 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 5.0 STAGE SERIES 2
B 200 12000
A (BIT TO BEND) (16270)
(BIT TO 11152
STAB.)
900 GPM (3407 LPM) (15120)
10000
(5792)
840
(13558)
150
8000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 600 GPM (2271 LPM)
70%
Static 573485 lbf 255100 daN RQ (2712)
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 6-7 Lobe 5.0 Stage Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 840 psi 5,792 kPa 300 1,136 28 - 51
C = Overall Length 390.4 in 9916 mm Max Torque @ No Load 11,152 ft-lbs 15,120 Nm 600 2,271 83 - 106
Weight 4258.2 lbs 1931.5 kg Max Power 291 HP 217 kW 900 3,407 137 - 160
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 2 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.06 1.39 2.10 1.25 3.72 2.03 - 5.72 5.79 6.50
0.78 1.62 0.22 - 2.93 3.26 3.97 1.50 5.13 3.44 - 7.31 7.05 7.75
1.15 3.72 2.31 - 5.34 5.04 5.74 1.75 6.55 4.86 1.20 8.89 8.56 9.01
1.50 5.70 4.29 1.25 7.63 7.31 7.42 2.00 7.96 6.28 2.62 10.47 10.15 10.26
1.83 7.57 6.16 3.12 9.79 9.47 9.00 2.25 9.38 7.69 4.03 12.06 11.73 11.52
2.12 9.21 7.81 4.76 11.70 11.37 10.66 2.50 10.79 9.11 5.45 13.64 13.31 12.77
2.38 10.68 9.28 6.24 13.40 13.07 12.37
2.60 11.93 10.52 7.48 14.84 14.51 13.81
2.77 12.89 11.49 8.44 15.95 15.63 14.92
2.90 13.63 12.22 9.18 16.81 16.48 15.77
2.97 14.02 12.62 9.58 17.26 16.94 16.23
3.00 14.19 12.79 9.74 17.46 17.13 16.43
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 211
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 2
212 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 5.0 STAGE HR SERIES 2
B 200 18000
A (BIT TO BEND) (24404)
(BIT TO 17076
STAB.) 16000 (23152)
(8688)
900 GPM (3407 LPM) (21693)
1260
14000
150 (18981)
12000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 600 GPM (2271 LPM)
10000
100 (13558)
Bit Box Connection 6-5/8 REGULAR
70%
Static 573485 lbf 255100 daN RQ 2000
TO (2712)
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800 1000 1200 1400
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 6-7 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 1,260 psi 8,687 kPa 300 1,136 28 - 51
C = Overall Length 390.4 in 9916 mm Max Torque @ No Load 17,076 ft-lbs 23,152 Nm 600 2,271 83 - 106
Weight 4260.2 lbs 1932.4 kg Max Power 445 HP 332 kW 900 3,407 137 - 160
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 2 FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.06 1.39 2.10 1.25 3.72 2.03 - 5.72 5.79 6.50
0.78 1.62 0.22 - 2.93 3.26 3.97 1.50 5.13 3.44 - 7.31 7.05 7.75
1.15 3.72 2.31 - 5.34 5.04 5.74 1.75 6.55 4.86 1.20 8.89 8.56 9.01
1.50 5.70 4.29 1.25 7.63 7.31 7.42 2.00 7.96 6.28 2.62 10.47 10.15 10.26
1.83 7.57 6.16 3.12 9.79 9.47 9.00 2.25 9.38 7.69 4.03 12.06 11.73 11.52
2.12 9.21 7.81 4.76 11.70 11.37 10.66 2.50 10.79 9.11 5.45 13.64 13.31 12.77
2.38 10.68 9.28 6.24 13.40 13.07 12.37
2.60 11.93 10.52 7.48 14.84 14.51 13.81
2.77 12.89 11.49 8.44 15.95 15.63 14.92
2.90 13.63 12.22 9.18 16.81 16.48 15.77
2.97 14.02 12.62 9.58 17.26 16.94 16.23
3.00 14.19 12.79 9.74 17.46 17.13 16.43
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 213
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 2
214 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 2.0 STAGE SERIES 2
B 96 8000
(2579)
A (BIT TO BEND) (10846)
900 GPM (3407 LPM)
374
(BIT TO
STAB.) 7100
84
(9626)
72 6000
600 GPM (2271 LPM) (8135)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
Bit Box Connection 6-5/8 REGULAR 48 300 GPM (1136 LPM) 4000
(5423)
70%
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 923500 lbf 411000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 7-8 Lobe 2.0 Stage Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.29 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 374 psi 2,579 kPa 300 1,136 33 - 44
C = Overall Length 308.4 in 7833 mm Max Torque @ No Load 7,100 ft-lbs 9,626 Nm 600 2,271 55 - 64
Weight 3594.2 lbs 1630.3 kg Max Power 104 HP 78 kW 900 3,407 77 - 84
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 2 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 2.0 Stage SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.42 1.95 3.09 1.25 4.67 2.55 - 7.19 7.31 8.45
0.78 2.04 0.27 - 3.65 4.18 5.32 1.50 6.45 4.33 - 9.24 8.83 9.97
1.15 4.67 2.90 - 6.76 6.29 7.43 1.75 8.22 6.10 1.51 11.28 10.76 11.48
1.50 7.16 5.39 1.57 9.75 9.23 9.43 2.00 10.00 7.88 3.29 13.33 12.80 13.00
1.83 9.51 7.74 3.92 12.57 12.05 11.32 2.25 11.78 9.66 5.06 15.38 14.85 14.52
2.12 11.57 9.80 5.98 15.05 14.52 13.39 2.50 13.56 11.44 6.84 17.42 16.90 16.03
2.38 13.42 11.65 7.83 17.27 16.74 15.61
2.60 14.98 13.22 9.40 19.15 18.62 17.48
2.77 16.19 14.43 10.60 20.60 20.07 18.94
2.90 17.11 15.35 11.53 21.71 21.18 20.05
2.97 17.61 15.85 12.03 22.31 21.78 20.64
3.00 17.82 16.06 12.24 22.56 22.04 20.90
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 215
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 2
216 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE SERIES 2
B 160 6000
A (BIT TO BEND) 900 GPM (3407 LPM) (8135)
(BIT TO 5285
STAB.)
140 (7165)
5000
(6779)
120
(2255)
327
4000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
Bit Box Connection 6-5/8 REGULAR 80 3000
(4067)
70%
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 923500 lbf 411000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 7-8 Lobe 3.0 Stage Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 327 psi 2,255 kPa 300 1,136 21 - 48
C = Overall Length 300.4 in 7630 mm Max Torque @ No Load 5,285 ft-lbs 7,165 Nm 600 2,271 71 - 97
Weight 3646.2 lbs 1653.9 kg Max Power 121 HP 90 kW 900 3,407 120 - 146
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 2 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.47 2.03 3.23 1.25 4.79 2.61 - 7.37 7.50 8.70
0.78 2.09 0.28 - 3.74 4.30 5.50 1.50 6.61 4.44 - 9.48 9.05 10.25
1.15 4.79 2.98 - 6.94 6.45 7.65 1.75 8.43 6.26 1.55 11.59 11.03 11.80
1.50 7.34 5.53 1.61 10.02 9.47 9.69 2.00 10.26 8.08 3.37 13.69 13.14 13.35
1.83 9.75 7.94 4.02 12.93 12.37 11.61 2.25 12.08 9.91 5.19 15.80 15.25 14.90
2.12 11.86 10.05 6.14 15.48 14.93 13.73 2.50 13.90 11.73 7.02 17.91 17.35 16.44
2.38 13.76 11.95 8.03 17.77 17.21 16.01
2.60 15.36 13.56 9.64 19.7 19.15 17.95
2.77 16.60 14.79 10.88 21.20 20.65 19.45
2.90 17.55 15.74 11.82 22.34 21.79 20.59
2.97 18.06 16.25 12.33 22.96 22.41 21.20
3.00 18.28 16.47 12.55 23.22 22.67 21.47
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 217
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 2
218 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE HR SERIES 2 13280
B 160 (18005)
A (BIT TO BEND)
(4895)
900 GPM (3407 LPM)
710
(BIT TO
STAB.) 11620
140 (15755)
11140
(15104)
9960
120 (13504)
650 GPM (2461 LPM)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
6640
Bit Box Connection 6-5/8 REGULAR 80 (9003)
70%
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 200 400 600 800
Absolute Overpull 923500 lbf 411000 daN (1379) (2758) (4137) (5516)
DIFFERENTIAL PRESSURE PSI (kPa)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm Performance Based on Water at 70°F (21°C)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.47 2.03 3.23 1.25 4.79 2.61 -2.10 7.37 7.50 8.70
0.78 2.09 0.28 - 3.74 4.30 5.50 1.50 6.61 4.44 -0.28 9.48 9.05 10.25
1.15 4.79 2.98 - 6.94 6.45 7.65 1.75 8.43 6.26 1.55 11.59 11.03 11.80
1.50 7.34 5.53 1.61 10.02 9.47 9.69 2.00 10.26 8.08 3.37 13.69 13.14 13.35
1.83 9.75 7.94 4.02 12.93 12.37 11.61 2.25 12.08 9.91 5.19 15.80 15.25 14.90
2.12 11.86 10.05 6.14 15.48 14.93 13.73 2.50 13.90 11.73 7.02 17.91 17.35 16.44
2.38 13.76 11.95 8.03 17.77 17.21 16.01
2.60 15.36 13.56 9.64 19.70 19.15 17.95
2.77 16.60 14.79 10.88 21.20 20.65 19.45
2.90 17.55 15.74 11.82 22.34 21.79 20.59
2.97 18.06 16.25 12.33 22.96 22.41 21.20
3.00 18.28 16.47 12.55 23.22 22.67 21.47
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 219
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 2
220 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.4 STAGE HR SERIES 2 22530
B 90 (30547)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 25000
STAB.)
80 (33895)
(5516)
70
800
20000
(27116)
60 450 GPM (1703 LPM)
70%
(6779)
10 RQ
TO
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 923500 lbf 411000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6506) (6895)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 0.92 1.17 1.73 1.25 3.31 1.80 - 5.09 5.14 5.70
0.78 1.44 0.19 - 2.62 2.87 3.43 1.50 4.57 3.06 - 6.48 6.27 6.83
1.15 3.31 2.06 - 4.73 4.49 5.04 1.75 5.82 4.32 1.07 7.87 7.62 7.96
1.50 5.07 3.82 1.11 6.74 6.48 6.57 2.00 7.08 5.58 2.33 9.26 9.01 9.09
1.83 6.73 5.48 2.78 8.63 8.37 8.01 2.25 8.34 6.84 3.59 10.65 10.40 10.23
2.12 8.19 6.94 4.24 10.29 10.04 9.48 2.50 9.60 8.10 4.85 12.04 11.79 11.36
2.38 9.50 8.25 5.55 11.79 11.53 10.97
2.60 10.61 9.36 6.65 13.05 12.79 12.24
2.77 11.47 10.22 7.51 14.02 13.77 13.21
2.90 12.12 10.87 8.16 14.77 14.51 13.96
2.97 12.47 11.22 8.52 15.17 14.91 14.36
3.00 12.62 11.37 8.67 15.34 15.08 14.53
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 221
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 2
222 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE SERIES 2
B 180 12000
A (BIT TO BEND)
(BIT TO 900 GPM (3407 LPM) (16270)
STAB.) 160 10966
(5075)
(14868)
736
10000
140 (13558)
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100
Bit Box Connection 6-5/8 REGULAR 6000
70%
Max. Overpull for Re-run 554100 lbf 246000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 923500 lbf 411000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 7-8 Lobe 4.0 Stage Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.18 rev/gal 0.05 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 600 psi 4,137 kPa 300 1,136 48 - 64
C = Overall Length 346.4 in 8799 mm Max Torque @ No Load 9,470 ft-lbs 12,840 Nm 600 2,271 88 - 104
Weight 3968.2 lbs 1799.9 kg Max Power 231 HP 172 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 2 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.65 2.55 1.25 4.17 2.28 - 6.43 6.52 7.42
0.78 1.82 0.24 - 3.28 3.70 4.60 1.50 5.76 3.87 - 8.23 7.90 8.80
1.15 4.17 2.60 - 6.02 5.64 6.54 1.75 7.35 5.46 1.35 10.03 9.62 10.19
1.50 6.40 4.82 1.41 8.64 8.23 8.38 2.00 8.94 7.05 2.94 11.83 11.42 11.57
1.83 8.50 6.92 3.50 11.11 10.70 10.11 2.25 10.53 8.64 4.53 13.64 13.22 12.95
2.12 10.34 8.76 5.35 13.29 12.87 11.97 2.50 12.12 10.22 6.12 15.44 15.02 14.34
2.38 11.99 10.42 7.00 15.23 14.82 13.92
2.60 13.39 11.82 8.40 16.88 16.46 15.56
2.77 14.47 12.90 9.48 18.15 17.74 16.84
2.90 15.30 13.72 10.31 19.13 18.71 17.81
2.97 15.74 14.17 10.75 19.65 19.23 18.33
3.00 15.93 14.36 10.94 19.87 19.46 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 223
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 2
224 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE HR SERIES 2
B 180
(6481)
A (BIT TO BEND)
940
(BIT TO 18000
STAB.) 160 (33895)
900 GPM (3407 LPM) 14830
140 (20107)
14000
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100
10000
Bit Box Connection 6-5/8 REGULAR (20337)
70%
TO (6780)
0
Max. Overpull for Re-run 554100 lbf 246000 daN 100 200 300 400 500 600 700 800 900 1000
0
(689) (1379) (2068) (2758) (3447) (4137) (4826) (5516) (6205) (6895)
Absolute Overpull 923500 lbf 411000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 7-8 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 940 psi 6,481 kPa 300 1,136 48 - 64
C = Overall Length 346.4 in 8799 mm Max Torque @ No Load 14,830 ft-lbs 20,107 Nm 600 2,271 88 - 104
Weight 3626 lbs 1644.7 kg Max Power 361 HP 270 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 2 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.23 1.65 2.55 1.25 4.17 2.28 - 6.43 6.52 7.42
0.78 1.82 0.24 - 3.28 3.70 4.60 1.50 5.76 3.87 - 8.23 7.90 8.80
1.15 4.17 2.60 - 6.02 5.64 6.54 1.75 7.35 5.46 1.35 10.03 9.62 10.19
1.50 6.40 4.82 1.41 8.64 8.23 8.38 2.00 8.94 7.05 2.94 11.83 11.42 11.57
1.83 8.50 6.92 3.50 11.11 10.70 10.11 2.25 10.53 8.64 4.53 13.64 13.22 12.95
2.12 10.34 8.76 5.35 13.29 12.87 11.97 2.50 12.12 10.22 6.12 15.44 15.02 14.34
2.38 11.99 10.42 7.00 15.23 14.82 13.92
2.60 13.39 11.82 8.40 16.88 16.46 15.56
2.77 14.47 12.90 9.48 18.15 17.74 16.84
2.90 15.30 13.72 10.31 19.13 18.71 17.81
2.97 15.74 14.17 10.75 19.65 19.23 18.33
3.00 15.93 14.36 10.94 19.87 19.46 18.56
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 225
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 2
226 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 5.9 STAGE SERIES 2 25966
B 160
(35205)
(9584)
A (BIT TO BEND)
1390
(BIT TO 900 GPM (3407 LPM)
STAB.) 22720
140 (30804) 21870
19475 (29652)
120 (26405)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
12980
80
Bit Box Connection 6-5/8 REGULAR (17599)
70%
TO
0
Max. Overpull for Re-run 554100 lbf 246000 daN 0 200 400 600 800 1000 1200 1400 1600
(1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
Absolute Overpull 923500 lbf 411000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 16.87 in 428 mm
Lobe Configuration 7-8 Lobe 5.9 Stage HR Flow Rate Speed
Adjustable 74.7 in 1897 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60.1 in 1527 mm
Max Differential @ No Load 1,390 psi 9,584 kPa 400 1,514 36 - 60
C = Overall Length 440.4 in 11186 mm Max Torque @ No Load 21,870 ft-lbs 29,652 Nm 650 2,461 75 - 100
Weight 5141.2 lbs 2332 kg Max Power 471 HP 351 kW 900 3,407 113 - 140
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 2 FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 2
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 0.92 1.17 1.73 1.25 3.31 1.80 - 5.09 5.14 5.70
0.78 1.44 0.19 - 2.62 2.87 3.43 1.50 4.57 3.06 - 6.48 6.27 6.83
1.15 3.31 2.06 - 4.73 4.49 5.04 1.75 5.82 4.32 1.07 7.87 7.62 7.96
1.50 5.07 3.82 1.11 6.74 6.48 6.57 2.00 7.08 5.58 2.33 9.26 9.01 9.09
1.83 6.73 5.48 2.78 8.63 8.37 8.01 2.25 8.34 6.84 3.59 10.65 10.40 10.23
2.12 8.19 6.94 4.24 10.29 10.04 9.48 2.50 9.60 8.10 4.85 12.04 11.79 11.36
2.38 9.50 8.25 5.55 11.79 11.53 10.97
2.60 10.61 9.36 6.65 13.05 12.79 12.24
2.77 11.47 10.22 7.51 14.02 13.77 13.21
2.90 12.12 10.87 8.16 14.77 14.51 13.96
2.97 12.47 11.22 8.52 15.17 14.91 14.36
3.00 12.62 11.37 8.67 15.34 15.08 14.53
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 227
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 4-5 Lobe 5.3 Stage HR MUD LUBE
228 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 4-5 Lobe 5.3 STAGE HR MUD LUBE
B 270
(8618)
1250
A (BIT TO BEND)
(BIT TO 16000
STAB.) 240 (21693)
900 GPM (3407 LPM) 13620
210 (18466)
12000
180
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 150 600 GPM (2271 LPM)
70%
UE
Static 534312 lbf 237670 daN 30 RQ
TO
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 904100 lbf 402000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 4-5 Lobe 5.3 Stage HR Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.24 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 1,250 psi 8,618 kPa 300 1,136 50 - 72
C = Overall Length 368.2 in 9352 mm Max Torque @ No Load 13,620 ft-lbs 18,466 Nm 600 2,271 122 - 144
Weight 3143.2 lbs 1425.7 kg Max Power 503 HP 375 kW 900 3,407 194 - 216
ADJUSTABLE BUILD RATE: 8 in (203 mm) 4-5 Lobe 5.3 Stage HR MUD LUBE FBH BUILD RATE: 8 in (203 mm) 4-5 Lobe 5.3 Stage HR MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.59 1.97 2.78 1.25 3.93 2.14 - 6.56 6.69 7.50
0.78 1.72 0.24 - 3.66 3.96 4.77 1.50 5.43 3.64 - 8.22 8.03 8.84
1.15 3.94 2.46 - 6.21 5.85 6.66 1.75 6.93 5.14 1.26 9.88 9.51 10.18
1.50 6.04 4.56 1.34 8.63 8.25 8.45 2.00 8.42 6.63 2.76 11.54 11.17 11.53
1.83 8.02 6.53 3.32 10.91 10.53 10.14 2.25 9.92 8.13 4.26 13.21 12.83 12.87
2.12 9.75 8.27 5.06 12.91 12.53 11.72 2.50 11.42 9.63 5.75 14.87 14.49 14.21
2.38 11.31 9.83 6.62 14.70 14.33 13.51
2.60 12.63 11.15 7.94 16.22 15.84 15.03
2.77 13.65 12.17 8.95 17.39 17.02 16.21
2.90 14.43 12.95 9.73 18.29 17.91 17.10
2.97 14.85 13.36 10.15 18.77 18.40 17.59
3.00 15.03 13.54 10.33 18.98 18.60 17.79
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 229
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 5-6 Lobe 3.0 Stage MUD LUBE
230 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 5-6 Lobe 3.0 STAGE HR MUD LUBE
B 200 5000
A (BIT TO BEND) (6779)
(1979)
(BIT TO 900 GPM (3407 LPM)
287
STAB.) 180 4082
(5534)
160 4000
(5423)
140 700 GPM (2650 LPM)
70%
Bearing Load - Off Bottom (1356)
RQ
Static 534312 lbf 237670 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 2.64 3.45 5.22 1.25 5.66 3.08 - 9.69 9.93 11.70
0.78 2.48 0.34 - 5.47 6.07 7.84 1.50 7.82 5.24 - 12.21 11.75 13.52
1.15 5.68 3.54 - 9.39 8.58 10.32 1.75 9.99 7.41 1.81 14.72 13.90 15.33
1.50 8.71 6.57 1.94 13.11 12.29 12.67 2.00 12.15 9.57 3.98 17.23 16.41 17.15
1.83 11.56 9.42 4.79 16.61 15.80 14.88 2.25 14.31 11.73 6.14 19.74 18.92 18.97
2.12 14.06 11.93 7.29 19.69 18.87 17.11 2.50 16.47 13.89 8.30 22.25 21.44 20.79
2.38 16.31 14.17 9.54 22.45 21.63 19.86
2.60 18.21 16.07 11.44 24.78 23.96 22.20
2.77 19.68 17.54 12.91 26.58 25.77 24.00
2.90 20.80 18.66 14.03 27.96 27.14 25.38
2.97 21.41 19.27 14.64 28.70 27.89 26.12
3.00 21.67 19.53 14.90 29.02 28.20 26.44
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 231
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 5-6 Lobe 3.0 Stage HR MUD LUBE
232 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 5-6 Lobe 3.0 STAGE HR MUD LUBE
B 200 8000
A (BIT TO BEND) (10846)
(2972)
(BIT TO 900 GPM (3407 LPM)
431
STAB.) 180
6123
(8302)
160
6000
140 700 GPM (2650 LPM) (8135)
70%
Bearing Load - Off Bottom UE
RQ
Static 534312 lbf 237670 daN 20 TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 2.64 3.45 5.22 1.25 5.66 3.08 - 9.69 9.93 11.70
0.78 2.48 0.34 - 5.47 6.07 7.84 1.50 7.82 5.24 - 12.21 11.75 13.52
1.15 5.68 3.54 - 9.39 8.58 10.32 1.75 9.99 7.41 1.81 14.72 13.90 15.33
1.50 8.71 6.57 1.94 13.11 12.29 12.67 2.00 12.15 9.57 3.98 17.23 16.41 17.15
1.83 11.56 9.42 4.79 16.61 15.80 14.88 2.25 14.31 11.73 6.14 19.74 18.92 18.97
2.12 14.06 11.93 7.29 19.69 18.87 17.11 2.50 16.47 13.89 8.30 22.25 21.44 20.79
2.38 16.31 14.17 9.54 22.45 21.63 19.86
2.60 18.21 16.07 11.44 24.78 23.96 22.20
2.77 19.68 17.54 12.91 26.58 25.77 24.00
2.90 20.80 18.66 14.03 27.96 27.14 25.38
2.97 21.41 19.27 14.64 28.70 27.89 26.12
3.00 21.67 19.53 14.90 29.02 28.20 26.44
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 233
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 4.0 Stage MUD LUBE
234 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE MUD LUBE
B 180 10000
(4599)
A (13558)
667
(BIT TO BEND)
(BIT TO 900 GPM (3407 LPM)
STAB.) 160 8793
(11922)
8000
140 (10846)
120
SPEED (RPM)
6000
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100 (8135)
Bit Box Connection 6-5/8 REGULAR
70%
Bearing Load - Off Bottom (2712)
UE
Static 534312 lbf 237670 daN 20 RQ
TO
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 904100 lbf 402000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 6-7 Lobe 4.0 Stage Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 600 psi 4,137 kPa 300 1,136 51 - 68
C = Overall Length 346.2 in 8793 mm Max Torque @ No Load 8,820 ft-lbs 11,958 Nm 600 2,271 94 - 111
Weight 2768.2 lbs 1255.6 kg Max Power 228 HP 170 kW 900 3,407 136 - 153
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage MUD LUBE FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 4.0 Stage MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.72 2.15 3.07 1.25 4.17 2.27 - 6.99 7.13 8.05
0.78 1.83 0.25 - 3.90 4.24 5.16 1.50 5.76 3.86 - 8.76 8.54 9.46
1.15 4.18 2.61 - 6.63 6.22 7.14 1.75 7.35 5.45 1.34 10.54 10.11 10.87
1.50 6.41 4.84 1.43 9.22 8.80 9.02 2.00 8.94 7.04 2.93 12.31 11.89 12.29
1.83 8.51 6.94 3.53 11.66 11.24 10.79 2.25 10.53 8.63 4.52 14.08 13.66 13.70
2.12 10.35 8.78 5.37 13.80 13.38 12.46 2.50 12.12 10.22 6.11 15.86 15.43 15.11
2.38 12.01 10.43 7.02 15.72 15.30 14.38
2.60 13.41 11.83 8.42 17.35 16.93 16.01
2.77 14.49 12.91 9.50 18.61 18.18 17.26
2.90 15.31 13.74 10.33 19.57 19.14 18.22
2.97 15.76 14.19 10.78 20.08 19.66 18.74
3.00 15.95 14.38 10.97 20.30 19.88 18.96
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 235
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 4.0 Stage HR MUD LUBE
236 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE HR MUD LUBE
B 180 13820
A (BIT TO BEND) (18737)
(6481)
(BIT TO
940
STAB.) 160 900 GPM (3407 LPM) 16000
(21693)
140 14000
(18981)
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100 10000
(13558)
Bit Box Connection 6-5/8 REGULAR
70%
(5423)
Bearing Load - Off Bottom UE
Static 534312 lbf 237670 daN 20 RQ 2000
TO (2712)
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 904100 lbf 402000 daN (1379) (2758) (4137) (5516) (6895) (8274)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.72 2.15 3.07 1.25 4.17 2.27 - 6.99 7.13 8.05
0.78 1.83 0.25 - 3.90 4.24 5.16 1.50 5.76 3.86 - 8.76 8.54 9.46
1.15 4.18 2.61 - 6.63 6.22 7.14 1.75 7.35 5.45 1.34 10.54 10.11 10.87
1.50 6.41 4.84 1.43 9.22 8.80 9.02 2.00 8.94 7.04 2.93 12.31 11.89 12.29
1.83 8.51 6.94 3.53 11.66 11.24 10.79 2.25 10.53 8.63 4.52 14.08 13.66 13.70
2.12 10.35 8.78 5.37 13.80 13.38 12.46 2.50 12.12 10.22 6.11 15.86 15.43 15.11
2.38 12.01 10.43 7.02 15.72 15.30 14.38
2.60 13.41 11.83 8.42 17.35 16.93 16.01
2.77 14.49 12.91 9.50 18.61 18.18 17.26
2.90 15.31 13.74 10.33 19.57 19.14 18.22
2.97 15.76 14.19 10.78 20.08 19.66 18.74
3.00 15.95 14.38 10.97 20.30 19.88 18.96
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 237
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 5.0 Stage MUD LUBE
238 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 5.0 STAGE MUD LUBE
B 200 12000
A (BIT TO BEND) (16270)
(BIT TO 11152
STAB.)
900 GPM (3407 LPM) (15120)
10000
(5792)
840
(13558)
150
8000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 600 GPM (2271 LPM)
70%
Static 534312 lbf 237670 daN RQ (2712)
TO
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 200 400 600 800 1000
Absolute Overpull 904100 lbf 402000 daN (1379) (2758) (4137) (5516) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 6-7 Lobe 5.0 Stage Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 840 psi 5,792 kPa 300 1,136 28 - 51
C = Overall Length 390.2 in 9911 mm Max Torque @ No Load 11,152 ft-lbs 15,120 Nm 600 2,271 83 - 106
Weight 3203.2 lbs 1452.9 kg Max Power 291 HP 217 kW 900 3,407 137 - 160
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage MUD LUBE FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.48 1.81 2.53 1.25 3.71 2.02 - 6.19 6.30 7.02
0.78 1.63 0.23 - 3.44 3.72 4.44 1.50 5.13 3.44 - 7.75 7.58 8.30
1.15 3.72 2.32 - 5.84 5.52 6.25 1.75 6.55 4.86 1.19 9.31 8.98 9.58
1.50 5.71 4.31 1.27 8.11 7.77 7.95 2.00 7.96 6.27 2.61 10.87 10.54 10.86
1.83 7.58 6.18 3.14 10.24 9.91 9.56 2.25 9.38 7.69 4.02 12.43 12.10 12.13
2.12 9.22 7.82 4.78 12.12 11.79 11.07 2.50 10.80 9.10 5.44 13.99 13.66 13.41
2.38 10.69 9.29 6.26 13.80 13.47 12.75
2.60 11.94 10.54 7.50 15.23 14.89 14.17
2.77 12.90 11.50 8.46 16.33 15.99 15.27
2.90 13.64 12.24 9.20 17.17 16.83 16.11
2.97 14.03 12.63 9.60 17.62 17.29 16.57
3.00 14.20 12.80 9.77 17.81 17.48 16.76
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 239
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 6-7 Lobe 5.0 Stage HR MUD LUBE
240 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 5.0 STAGE HR MUD LUBE
B 200 18000
A (BIT TO BEND) (24404)
(BIT TO 17076
STAB.) 16000 (23152)
(8688)
900 GPM (3407 LPM) (21693)
1260
14000
150 (18981)
12000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 600 GPM (2271 LPM)
10000
100 (13558)
Bit Box Connection 6-5/8 REGULAR
70%
Static 534312 lbf 237670 daN RQ 2000
TO (2712)
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 200 400 600 800 1000 1200 1400
Absolute Overpull 904100 lbf 402000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 6-7 Lobe 5.0 Stage HR Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 1,260 psi 8,687 kPa 300 1,136 28 - 51
C = Overall Length 390.2 in 9911 mm Max Torque @ No Load 17,076 ft-lbs 23,152 Nm 600 2,271 83 - 106
Weight 3205.2 lbs 1453.9 kg Max Power 445 HP 332 kW 900 3,407 137 - 160
ADJUSTABLE BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage HR MUD LUBE FBH BUILD RATE: 8 in (203 mm) 6-7 Lobe 5.0 Stage HR MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.48 1.81 2.53 1.25 3.71 2.02 - 6.19 6.30 7.02
0.78 1.63 0.23 - 3.44 3.72 4.44 1.50 5.13 3.44 - 7.75 7.58 8.30
1.15 3.72 2.32 - 5.84 5.52 6.25 1.75 6.55 4.86 1.19 9.31 8.98 9.58
1.50 5.71 4.31 1.27 8.11 7.77 7.95 2.00 7.96 6.27 2.61 10.87 10.54 10.86
1.83 7.58 6.18 3.14 10.24 9.91 9.56 2.25 9.38 7.69 4.02 12.43 12.10 12.13
2.12 9.22 7.82 4.78 12.12 11.79 11.07 2.50 10.80 9.10 5.44 13.99 13.66 13.41
2.38 10.69 9.29 6.26 13.80 13.47 12.75
2.60 11.94 10.54 7.50 15.23 14.89 14.17
2.77 12.90 11.50 8.46 16.33 15.99 15.27
2.90 13.64 12.24 9.20 17.17 16.83 16.11
2.97 14.03 12.63 9.60 17.62 17.29 16.57
3.00 14.20 12.80 9.77 17.81 17.48 16.76
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 241
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 2.0 Stage MUD LUBE
242 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 2.0 STAGE MUD LUBE
B 96 8000
(2579)
A (BIT TO BEND) (10846)
900 GPM (3407 LPM)
374
(BIT TO
STAB.) 7100
84
(9626)
72 6000
600 GPM (2271 LPM) (8135)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
Bit Box Connection 6-5/8 REGULAR 48 300 GPM (1136 LPM) 4000
(5423)
70%
TO
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 904100 lbf 402000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 7-8 Lobe 2.0 Stage Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.29 rev/gal 0.08 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 374 psi 2,579 kPa 300 1,136 33 - 44
C = Overall Length 308.2 in 7828 mm Max Torque @ No Load 7,100 ft-lbs 9,626 Nm 600 2,271 55 - 64
Weight 2539.2 lbs 1151.8 kg Max Power 104 HP 78 kW 900 3,407 77 - 84
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 2.0 Stage MUD LUBE FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 2.0 Stage MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 2.01 2.55 3.71 1.25 4.66 2.54 - 7.87 8.04 9.21
0.78 2.04 0.28 - 4.40 4.83 5.99 1.50 6.44 4.32 - 9.88 9.60 10.76
1.15 4.68 2.92 - 7.52 6.99 8.15 1.75 8.22 6.10 1.49 11.89 11.35 12.31
1.50 7.17 5.41 1.60 10.47 9.93 10.20 2.00 10.00 7.88 3.27 13.90 13.37 13.87
1.83 9.52 7.76 3.94 13.25 12.71 12.13 2.25 11.78 9.66 5.05 15.91 15.38 15.42
2.12 11.58 9.82 6.01 15.69 15.15 13.98 2.50 13.56 11.44 6.83 17.93 17.39 16.97
2.38 13.43 11.67 7.86 17.88 17.34 16.17
2.60 15.00 13.24 9.42 19.73 19.19 18.02
2.77 16.21 14.45 10.63 21.16 20.62 19.45
2.90 17.13 15.37 11.56 22.25 21.71 20.55
2.97 17.63 15.87 12.05 22.84 22.30 21.14
3.00 17.84 16.08 12.27 23.09 22.55 21.39
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 243
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.0 Stage MUD LUBE
244 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE MUD LUBE
B 160 6000
A (BIT TO BEND) 900 GPM (3407 LPM) (8135)
(BIT TO 5285
STAB.)
140 (7165)
5000
(6779)
120
(2255)
327
4000
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
Bit Box Connection 6-5/8 REGULAR 80 3000
(4067)
70%
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 50 100 150 200 250 300 350 400
Absolute Overpull 904100 lbf 402000 daN (345) (690) (1034) (1379) (1724) (2069) (2413) (2758)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 7-8 Lobe 3.0 Stage Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 327 psi 2,255 kPa 300 1,136 21 - 48
C = Overall Length 300.2 in 7625 mm Max Torque @ No Load 5,285 ft-lbs 7,165 Nm 600 2,271 71 - 97
Weight 2591.2 lbs 1175.3 kg Max Power 121 HP 90 kW 900 3,407 120 - 146
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage MUD LUBE FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 3.0 Stage MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 2.08 2.65 3.88 1.25 4.78 2.60 - 8.08 8.26 9.49
0.78 2.10 0.29 - 4.53 4.97 6.20 1.50 6.61 4.43 - 10.15 9.85 11.08
1.15 4.80 2.99 - 7.74 7.17 8.41 1.75 8.43 6.25 1.53 12.22 11.66 12.67
1.50 7.35 5.55 1.64 10.77 10.21 10.49 2.00 10.26 8.08 3.36 14.29 13.73 14.25
1.83 9.76 7.96 4.05 13.64 13.07 12.45 2.25 12.08 9.90 5.18 16.36 15.80 15.84
2.12 11.88 10.07 6.16 16.15 15.58 14.35 2.50 13.91 11.73 7.01 18.43 17.86 17.43
2.38 13.78 11.97 8.06 18.41 17.84 16.61
2.60 15.38 13.58 9.66 20.31 19.74 18.51
2.77 16.62 14.82 10.90 21.79 21.22 19.99
2.90 17.57 15.76 11.85 22.91 22.35 21.11
2.97 18.08 16.28 12.36 23.52 22.95 21.72
3.00 18.30 16.49 12.58 23.78 23.21 21.98
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 245
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.0 Stage HR MUD LUBE
246 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE HR MUD LUBE 13280
B 160 (18005)
A (BIT TO BEND)
(4895)
900 GPM (3407 LPM)
710
(BIT TO
STAB.) 11620
140 (15755)
11140
(15104)
9960
120 (13504)
650 GPM (2461 LPM)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
6640
Bit Box Connection 6-5/8 REGULAR 80 (9003)
70%
TO
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 200 400 600 800
Absolute Overpull 904100 lbf 402000 daN (1379) (2758) (4137) (5516)
DIFFERENTIAL PRESSURE PSI (kPa)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm Performance Based on Water at 70°F (21°C)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 2.08 2.65 3.88 1.25 4.78 2.60 - 8.08 8.26 9.49
0.78 2.10 0.29 - 4.53 4.97 6.20 1.50 6.61 4.43 - 10.15 9.85 11.08
1.15 4.80 2.99 - 7.74 7.17 8.41 1.75 8.43 6.25 1.53 12.22 11.66 12.67
1.50 7.35 5.55 1.64 10.77 10.21 10.49 2.00 10.26 8.08 3.36 14.29 13.73 14.25
1.83 9.76 7.96 4.05 13.64 13.07 12.45 2.25 12.08 9.90 5.18 16.36 15.80 15.84
2.12 11.88 10.07 6.16 16.15 15.58 14.35 2.50 13.91 11.73 7.01 18.43 17.86 17.43
2.38 13.78 11.97 8.06 18.41 17.84 16.61
2.60 15.38 13.58 9.66 20.31 19.74 18.51
2.77 16.62 14.82 10.90 21.79 21.22 19.99
2.90 17.57 15.76 11.85 22.91 22.35 21.11
2.97 18.08 16.28 12.36 23.52 22.95 21.72
3.00 18.30 16.49 12.58 23.78 23.21 21.98
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 247
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 3.4 Stage HR MUD LUBE
248 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.4 STAGE HR MUD LUBE 22530
B 90 (30547)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 25000
STAB.)
80 (33895)
(5516)
70
800
20000
(27116)
60 450 GPM (1703 LPM)
70%
(6779)
10 RQ
TO
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 904100 lbf 402000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6506) (6895)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.27 1.53 2.10 1.25 3.30 1.80 - 5.48 5.57 6.13
0.78 1.45 0.20 - 3.04 3.26 3.82 1.50 4.56 3.06 - 6.85 6.72 7.28
1.15 3.31 2.07 - 5.14 4.90 5.46 1.75 5.82 4.32 1.06 8.22 7.96 8.44
1.50 5.08 3.83 1.13 7.13 6.87 7.01 2.00 7.08 5.58 2.32 9.60 9.33 9.59
1.83 6.74 5.49 2.79 9.00 8.74 8.47 2.25 8.34 6.84 3.58 10.97 10.71 10.74
2.12 8.20 6.96 4.25 10.64 10.38 9.82 2.50 9.60 8.10 4.84 12.34 12.08 11.89
2.38 9.51 8.26 5.56 12.12 11.86 11.29
2.60 10.62 9.37 6.67 13.37 13.11 12.54
2.77 11.48 10.23 7.53 14.33 14.07 13.51
2.90 12.13 10.88 8.18 15.07 14.81 14.24
2.97 12.48 11.24 8.54 15.47 15.20 14.64
3.00 12.63 11.39 8.69 15.64 15.37 14.81
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 249
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 4.0 Stage MUD LUBE
250 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE MUD LUBE
B 180 12000
A (BIT TO BEND)
(BIT TO 900 GPM (3407 LPM) (16270)
STAB.) 160 10966
(5075)
(14868)
736
10000
140 (13558)
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100
Bit Box Connection 6-5/8 REGULAR 6000
70%
Max. Overpull for Re-run 542500 lbf 241000 daN 0
0 100 200 300 400 500 600 700 800
Absolute Overpull 904100 lbf 402000 daN (690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 7-8 Lobe 4.0 Stage Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.18 rev/gal 0.05 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 600 psi 4,137 kPa 300 1,136 48 - 64
C = Overall Length 346.2 in 8793 mm Max Torque @ No Load 9,470 ft-lbs 12,840 Nm 600 2,271 88 - 104
Weight 2913.2 lbs 1321.4 kg Max Power 231 HP 172 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage MUD LUBE FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.72 2.15 3.07 1.25 4.17 2.27 - 6.99 7.13 8.05
0.78 1.83 0.25 - 3.90 4.24 5.16 1.50 5.76 3.86 - 8.76 8.54 9.46
1.15 4.18 2.61 - 6.63 6.22 7.14 1.75 7.35 5.45 1.34 10.54 10.11 10.87
1.50 6.41 4.84 1.43 9.22 8.80 9.02 2.00 8.94 7.04 2.93 12.31 11.89 12.29
1.83 8.51 6.94 3.53 11.66 11.24 10.79 2.25 10.53 8.63 4.52 14.08 13.66 13.70
2.12 10.35 8.78 5.37 13.80 13.38 12.46 2.50 12.12 10.22 6.11 15.86 15.43 15.11
2.38 12.01 10.43 7.02 15.72 15.30 14.38
2.60 13.41 11.83 8.42 17.35 16.93 16.01
2.77 14.49 12.91 9.50 18.61 18.18 17.26
2.90 15.31 13.74 10.33 19.57 19.14 18.22
2.97 15.76 14.19 10.78 20.08 19.66 18.74
3.00 15.95 14.38 10.97 20.30 19.88 18.96
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 251
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 4.0 Stage HR MUD LUBE
252 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE HR MUD LUBE
B 180
(6481)
A (BIT TO BEND)
940
(BIT TO 18000
STAB.) 160 (33895)
900 GPM (3407 LPM) 14830
140 (20107)
14000
120
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm 100
10000
Bit Box Connection 6-5/8 REGULAR (20337)
70%
TO (6780)
0
Max. Overpull for Re-run 542500 lbf 241000 daN 100 200 300 400 500 600 700 800 900 1000
0
(689) (1379) (2068) (2758) (3447) (4137) (4826) (5516) (6205) (6895)
Absolute Overpull 904100 lbf 402000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 7-8 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 940 psi 6,481 kPa 300 1,136 48 - 64
C = Overall Length 346.2 in 8793 mm Max Torque @ No Load 14,830 ft-lbs 20,107 Nm 600 2,271 88 - 104
Weight 2913.2 lbs 1321.4 kg Max Power 361 HP 270 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage HR MUD LUBE FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 4.0 Stage HR MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.72 2.15 3.07 1.25 4.17 2.27 - 6.99 7.13 8.05
0.78 1.83 0.25 - 3.90 4.24 5.16 1.50 5.76 3.86 - 8.76 8.54 9.46
1.15 4.18 2.61 - 6.63 6.22 7.14 1.75 7.35 5.45 1.34 10.54 10.11 10.87
1.50 6.41 4.84 1.43 9.22 8.80 9.02 2.00 8.94 7.04 2.93 12.31 11.89 12.29
1.83 8.51 6.94 3.53 11.66 11.24 10.79 2.25 10.53 8.63 4.52 14.08 13.66 13.70
2.12 10.35 8.78 5.37 13.80 13.38 12.46 2.50 12.12 10.22 6.11 15.86 15.43 15.11
2.38 12.01 10.43 7.02 15.72 15.30 14.38
2.60 13.41 11.83 8.42 17.35 16.93 16.01
2.77 14.49 12.91 9.50 18.61 18.18 17.26
2.90 15.31 13.74 10.33 19.57 19.14 18.22
2.97 15.76 14.19 10.78 20.08 19.66 18.74
3.00 15.95 14.38 10.97 20.30 19.88 18.96
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 253
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
8 in (203 mm) 7-8 Lobe 5.9 Stage HR MUD LUBE
254 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 5.9 STAGE MUD LUBE 25966
B 160
(35205)
(9584)
A (BIT TO BEND)
1390
(BIT TO 900 GPM (3407 LPM)
STAB.) 22720
140 (30804) 21870
19475 (29652)
120 (26405)
SPEED (RPM)
Bit Size Range 9-7/8 - 12-1/4 in 251 - 311 mm
12980
80
Bit Box Connection 6-5/8 REGULAR (17599)
70%
TO
0
Max. Overpull for Re-run 542500 lbf 241000 daN 0 200 400 600 800 1000 1200 1400 1600
(1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
Absolute Overpull 904100 lbf 402000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 40000 ft-lbs 54233 Nm
A = Bit To Stabilizer (center) 23.5 in 597 mm
Lobe Configuration 7-8 Lobe 5.9 Stage HR Flow Rate Speed
Adjustable 74.9 in 1902 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 60 in 1524 mm
Max Differential @ No Load 1,390 psi 9,584 kPa 400 1,514 36 - 60
C = Overall Length 440.2 in 11181 mm Max Torque @ No Load 21,870 ft-lbs 29,652 Nm 650 2,461 75 - 100
Weight 4086.2 lbs 1853.5 kg Max Power 471 HP 351 kW 900 3,407 113 - 140
ADJUSTABLE BUILD RATE: 8 in (203 mm) 7-8 Lobe 5.9 Stage HR MUD LUBE FBH BUILD RATE: 8 in (203 mm) 7-8 Lobe 5.9 Stage HR MUD LUBE
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4 Size 9-7/8 10-5/8 12-1/4 9-7/8 10-5/8 12-1/4
(251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm) (251 mm) (270 mm) (311 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.27 1.53 2.10 1.25 3.30 1.80 - 5.48 5.57 6.13
0.78 1.45 0.20 - 3.04 3.26 3.82 1.50 4.56 3.06 - 6.85 6.72 7.28
1.15 3.31 2.07 - 5.14 4.90 5.46 1.75 5.82 4.32 1.06 8.22 7.96 8.44
1.50 5.08 3.83 1.13 7.13 6.87 7.01 2.00 7.08 5.58 2.32 9.60 9.33 9.59
1.83 6.74 5.49 2.79 9.00 8.74 8.47 2.25 8.34 6.84 3.58 10.97 10.71 10.74
2.12 8.20 6.96 4.25 10.64 10.38 9.82 2.50 9.60 8.10 4.84 12.34 12.08 11.89
2.38 9.51 8.26 5.56 12.12 11.86 11.29
2.60 10.62 9.37 6.67 13.37 13.11 12.54
2.77 11.48 10.23 7.53 14.33 14.07 13.51
2.90 12.13 10.88 8.18 15.07 14.81 14.24
2.97 12.48 11.24 8.54 15.47 15.20 14.64
3.00 12.63 11.39 8.69 15.64 15.37 14.81
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 255
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1
256 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE HR SERIES 1
B 180 13820
A (BIT TO BEND) (18737)
(6481)
(BIT TO
940
STAB.) 160 900 GPM (3407 LPM) 16000
(21693)
140 14000
(18981)
120
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm 100 10000
(13558)
Bit Box Connection 6-5/8 or 7-5/8 REGULAR
70%
(5423)
Bearing Load - Off Bottom UE
Static 852600 lbf 379260 daN 20 RQ 2000
TO (2712)
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 1235100 lbf 549000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 6-7 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 940 psi 6,481 kPa 400 1,514 51 - 68
C = Overall Length 364.7 in 9263 mm Max Torque @ No Load 13,820 ft-lbs 18,737 Nm 650 2,461 94 - 111
Weight 4831 lbs 2191.3 kg Max Power 358 HP 267 kW 900 3,407 136 - 153
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe 4.0 Stage
4.0 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.73 3.61 4.36 1.25 3.94 - - 6.40 7.77 8.52
0.78 1.12 - - 3.62 5.50 6.25 1.50 5.44 - - 8.19 8.98 9.73
1.15 3.34 - - 5.68 7.29 8.04 1.75 6.94 0.64 - 9.99 10.19 10.94
1.50 5.44 - - 8.19 8.98 9.73 2.00 8.44 2.14 - 11.79 11.40 12.15
1.83 7.42 1.12 - 10.57 10.58 11.33 2.25 9.94 3.64 1.11 13.58 12.61 13.36
2.12 9.16 2.86 0.33 12.65 11.98 12.73 2.50 11.44 5.14 2.61 15.38 13.82 14.57
2.38 10.72 4.42 1.89 14.52 13.24 13.99
2.60 12.04 5.74 3.21 16.10 14.31 15.05
2.77 13.06 6.76 4.23 17.32 15.44 15.88
2.90 13.84 7.54 5.01 18.25 16.38 16.51
2.97 14.26 7.96 5.43 18.76 16.88 16.84
3.00 14.44 8.14 5.61 18.97 17.10 16.99
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 257
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.0 Stage HR SERIES 1
258 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.0 STAGE HR SERIES 1 13280
B 160 (18005)
A (BIT TO BEND)
(4895)
900 GPM (3407 LPM)
710
(BIT TO
STAB.) 11620
140 (15755)
11140
(15104)
9960
120 (13504)
650 GPM (2461 LPM)
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm
6640
80
Bit Box Connection 6-5/8 or 7-5/8 REGULAR (9003)
70%
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 2.08 4.54 5.52 1.25 4.48 - - 7.28 9.10 10.09
0.78 1.27 - - 4.15 6.61 7.59 1.50 6.19 - - 9.38 10.43 11.41
1.15 3.80 - - 6.44 8.57 9.56 1.75 7.90 0.72 - 11.47 11.75 12.74
1.50 6.19 - - 9.38 10.43 11.41 2.00 9.61 2.43 - 13.57 13.08 14.06
1.83 8.45 1.27 - 12.14 12.18 13.16 2.25 11.31 4.14 1.27 15.66 14.40 15.39
2.12 10.43 3.25 0.38 14.58 13.72 14.70 2.50 13.02 5.84 2.97 17.76 15.73 16.71
2.38 12.20 5.03 2.16 16.75 15.09 16.08
2.60 13.70 6.53 3.66 18.60 16.26 17.24
2.77 14.86 7.69 4.82 20.02 17.56 18.14
2.90 15.75 8.57 5.70 21.11 18.65 18.83
2.97 16.23 9.05 6.18 21.70 19.23 19.20
3.00 16.43 9.26 6.39 21.95 19.49 19.36
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 259
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1
260 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.4 STAGE HR SERIES 1 22530
B 90 (30547)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 25000
STAB.)
80 (33895)
(5516)
70
800
20000
(27116)
60 450 GPM (1703 LPM)
70%
Static 852600 lbf 379260 daN 10 RQ
(6779)
TO
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 1235100 lbf 549000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6506) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 7-8 Lobe 3.4 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.09 rev/gal 0.02 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 800 psi 5,516 kPa 300 1,136 48 - 64
C = Overall Length 458.7 in 11651 mm Max Torque @ No Load 22,530 ft-lbs 30,547 Nm 600 2,271 88 - 104
Weight 5812 lbs 2636.3 kg Max Power 309 HP 230 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.4 Stage
3.4 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.28 2.46 2.94 1.25 3.16 - - 5.12 5.98 6.45
0.78 0.90 - - 2.88 4.06 4.53 1.50 4.36 - - 6.51 7.00 7.47
1.15 2.68 - - 4.56 5.57 6.04 1.75 5.56 0.51 - 7.90 8.02 8.49
1.50 4.36 -0.69 - 6.51 7.00 7.47 2.00 6.77 1.71 - 9.29 9.04 9.51
1.83 5.95 0.89 - 8.34 8.34 8.82 2.25 7.97 2.91 0.89 10.68 10.06 10.53
2.12 7.34 2.29 0.27 9.96 9.53 10.00 2.50 9.17 4.12 2.10 12.07 11.08 11.55
2.38 8.59 3.54 1.52 11.40 10.59 11.06
2.60 9.65 4.60 2.58 12.62 11.49 11.96
2.77 10.47 5.42 3.39 13.57 12.39 12.65
2.90 11.09 6.04 4.02 14.29 13.11 13.18
2.97 11.43 6.38 4.35 14.68 13.50 13.47
3.00 11.58 6.52 4.50 14.85 13.67 13.59
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 261
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1
262 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE SERIES 1
B 180 12000
A (BIT TO BEND)
(BIT TO 900 GPM (3407 LPM) (16270)
STAB.) 160 10966
(5075)
(14868)
736
10000
140 (13558)
120
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm 100
6000
Bit Box Connection 6-5/8 or 7-5/8 REGULAR
70%
0
Max. Overpull for Re-run 741100 lbf 330000 daN 0 100 200 300 400 500 600 700 800
(690) (1379) (2069) (2758) (3448) (4137) (4827) (5516)
Absolute Overpull 1235100 lbf 549000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 7-8 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 940 psi 6,481 kPa 400 1,514 48 - 64
C = Overall Length 361.7 in 9187 mm Max Torque @ No Load 14,830 ft-lbs 20,107 Nm 650 2,461 88 - 104
Weight 4943 lbs 2242.1 kg Max Power 361 HP 270 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 4.0 Stage
4.0 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.75 3.66 4.42 1.25 3.97 - - 6.45 7.85 8.61
0.78 1.13 - - 3.65 5.56 6.32 1.50 5.48 - - 8.26 9.06 9.83
1.15 3.37 - - 5.72 7.36 8.12 1.75 7.00 0.64 - 10.08 10.28 11.04
1.50 5.48 - - 8.26 9.06 9.83 2.00 8.51 2.15 - 11.89 11.50 12.26
1.83 7.48 1.12 - 10.66 10.67 11.43 2.25 10.02 3.67 1.12 13.70 12.72 13.48
2.12 9.24 2.88 0.34 12.76 12.08 12.84 2.50 11.53 5.18 2.63 15.52 13.93 14.69
2.38 10.81 4.45 1.91 14.65 13.35 14.11
2.60 12.14 5.78 3.24 16.24 14.42 15.18
2.77 13.17 6.81 4.27 17.47 15.57 16.01
2.90 13.95 7.60 5.05 18.42 16.51 16.64
2.97 14.37 8.02 5.48 18.92 17.02 16.98
3.00 14.56 8.20 5.66 19.14 17.23 17.13
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 263
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 5.9 Stage HR SERIES 1
264 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 5.9 STAGE SERIES 1 17570
B 160
(23820)
(5075)
A (BIT TO BEND)
940
(BIT TO 900 GPM (3407 LPM)
STAB.) 15370
140 (20840) 14830
13175 (20100)
120 (17860)
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm
8780
80
Bit Box Connection 6-5/8 or 7-5/8 REGULAR (11900)
70%
0
Max. Overpull for Re-run 741100 lbf 330000 daN 0 200 400 600 800 1000
(1379) (2758) (4137) (5516) (6895)
Absolute Overpull 1235100 lbf 549000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 7-8 Lobe 5.9 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 1,390 psi 9,584 kPa 400 1,514 41 - 60
C = Overall Length 458.7 in 11651 mm Max Torque @ No Load 21,870 ft-lbs 29,652 Nm 650 2,461 80 - 100
Weight 5953 lbs 2700.2 kg Max Power 496 HP 370 kW 900 3,407 119 - 140
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 5.9 Stage
5.9 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.28 2.46 2.94 1.25 3.16 - - 5.12 5.98 6.45
0.78 0.90 - - 2.88 4.06 4.53 1.50 4.36 - - 6.51 7.00 7.47
1.15 2.68 - - 4.56 5.57 6.04 1.75 5.56 0.51 - 7.90 8.02 8.49
1.50 4.36 - - 6.51 7.00 7.47 2.00 6.77 1.71 - 9.29 9.04 9.51
1.83 5.95 0.89 - 8.34 8.34 8.82 2.25 7.97 2.91 0.89 10.68 10.06 10.53
2.12 7.34 2.29 0.27 9.96 9.53 10.00 2.50 9.17 4.12 2.10 12.07 11.08 11.55
2.38 8.59 3.54 1.52 11.40 10.59 11.06
2.60 9.65 4.60 2.58 12.62 11.49 11.96
2.77 10.47 5.42 3.39 13.57 12.39 12.65
2.90 11.09 6.04 4.02 14.29 13.11 13.18
2.97 11.43 6.38 4.35 14.68 13.50 13.47
3.00 11.58 6.52 4.50 14.85 13.67 13.59
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 265
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) 3-4 Lobe 6.0 Stage SERIES 1
266 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 9 5/8 in (244 mm) 3-4 Lobe 6.0 STAGE SERIES 1
B 300
A (BIT TO BEND)
(6205)
(BIT TO
900
STAB.) 1200 GPM (4542 LPM)
12000
240 (16270)
11480
(15565)
900 GPM (3407 LPM)
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm
Bit Box Connection 6-5/8 or 7-5/8 REGULAR 600 GPM (2271 LPM)
70%
UE
Static 852600 lbf 379260 daN RQ
TO
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 200 400 600 800 1000
Absolute Overpull 1235100 lbf 549000 daN (1379) (2758) (4137) (5516) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 3-4 Lobe 6.0 Stage Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.22 rev/gal 0.06 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 900 psi 6,205 kPa 600 2,271 85 - 132
C = Overall Length 386.7 in 9822 mm Max Torque @ No Load 11,480 ft-lbs 15,565 Nm 900 3,407 153 - 201
Weight 5629 lbs 2553.3 kg Max Power 481 HP 359 kW 1,200 4,542 220 - 270
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) 3-4 Lobe 6.0 Stage SERIES 1 FBH BUILD RATE: 9-5/8 in (244 mm) 3-4 Lobe 6.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.6 3.27 3.94 1.25 3.72 - - 6.05 7.26 7.93
0.78 1.06 - - 3.41 5.08 5.75 1.50 5.14 - - 7.73 8.42 9.09
1.15 3.16 - - 5.37 6.8 7.46 1.75 6.56 0.6 - 9.41 9.58 10.25
1.50 5.14 - - 7.73 8.42 9.09 2.00 7.98 2.02 - 11.09 10.74 11.41
1.83 7.02 1.05 - 9.95 9.96 10.62
2.12 8.66 2.7 0.32 11.9 11.3 11.97
2.38 10.14 4.17 1.79 13.65 12.51 13.17
2.60 11.38 5.42 3.04 15.13 13.53 14.19
2.77 12.35 6.39 4 16.27 14.6 14.98
2.90 13.08 7.12 4.74 17.14 15.48 15.59
2.97 13.48 7.52 5.14 17.61 15.95 15.91
3.00 13.65 7.69 5.31 17.81 16.15 16.05
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 267
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) 6-7 Lobe 5.0 Stage SERIES 1
268 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 9 5/8 in (244 mm) 6-7 Lobe 5.0 STAGE SERIES 1 14011
B 180 (18996)
A (BIT TO BEND)
(BIT TO 14000
STAB.) 160 1200 GPM (4542 LPM) (18981)
(5709)
828
12000
140
(16270)
120 900 GPM (3407 LPM)
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm 100
8000
Bit Box Connection 6-5/8 or 7-5/8 REGULAR 600 GPM (2271 LPM) (10846)
70%
Bearing Load - Off Bottom UE 2000
Static 852600 lbf 379260 daN 20 RQ
TO (2712)
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 100 200 300 400 500 600 800 800 900
Absolute Overpull 1235100 lbf 549000 daN (690) (1379) (2069) (2758) (3448) (4137) (5516) (5516) (6203)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 6-7 Lobe 5.0 Stage Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.13 rev/gal 0.03 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 828 psi 5,709 kPa 600 2,271 46 - 78
C = Overall Length 366.7 in 9314 mm Max Torque @ No Load 14,011 ft-lbs 18,996 Nm 900 3,407 87 - 117
Weight 5510 lbs 2499.3 kg Max Power 341 HP 255 kW 1,200 4,542 128 - 156
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) 6-7 Lobe 5.0 Stage SERIES 1 FBH BUILD RATE: 9-5/8 in (244 mm) 6-7 Lobe 5.0 Stage SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.72 3.57 4.32 1.25 3.92 - - 6.36 7.72 8.46
0.78 1.11 - - 3.6 5.46 6.2 1.50 5.41 - - 8.15 8.93 9.67
1.15 3.32 - - 5.65 7.24 7.98 1.75 6.91 0.63 - 9.94 10.13 10.87
1.50 5.41 - - 8.15 8.93 9.67 2.00 8.4 2.13 - 11.72 11.34 12.08
1.83 7.38 1.11 - 10.51 10.52 11.26
2.12 9.11 2.84 0.33 12.58 11.92 12.66
2.38 10.67 4.39 1.88 14.43 13.17 13.91
2.60 11.98 5.71 3.2 16.01 14.23 14.97
2.77 12.99 6.72 4.21 17.22 15.36 15.79
2.90 13.77 7.5 4.99 18.15 16.29 16.42
2.97 14.19 7.91 5.4 18.65 16.79 16.75
3.00 14.37 8.09 5.58 18.86 17 16.9
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 269
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) 6-7 Lobe 5.0 Stage HR SERIES 1
270 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 9 5/8 in (244 mm) 6-7 Lobe 5.0 STAGE HR SERIES 1
B 180 21712
A (BIT TO BEND)
(BIT TO 1200 GPM (4542 LPM) (29437)
STAB.) 160
20000
(8688)
(27116)
1260
140
900 GPM (3407 LPM)
120
SPEED (RPM)
(20337)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm 100
Bit Box Connection 6-5/8 or 7-5/8 REGULAR 600 GPM (2271 LPM)
70%
UE (6779)
Bearing Load - Off Bottom
Static 852600 lbf 379260 daN 20 RQ
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.72 3.57 4.32 1.25 3.92 - - 6.36 7.72 8.46
0.78 1.11 - - 3.6 5.46 6.2 1.50 5.41 - - 8.15 8.93 9.67
1.15 3.32 - - 5.65 7.24 7.98 1.75 6.91 0.63 - 9.94 10.13 10.87
1.50 5.41 - - 8.15 8.93 9.67 2.00 8.4 2.13 - 11.72 11.34 12.08
1.83 7.38 1.11 - 10.51 10.52 11.26
2.12 9.11 2.84 0.33 12.58 11.92 12.66
2.38 10.67 4.39 1.88 14.43 13.17 13.91
2.60 11.98 5.71 3.2 16.01 14.23 14.97
2.77 12.99 6.72 4.21 17.22 15.36 15.79
2.90 13.77 7.5 4.99 18.15 16.29 16.42
2.97 14.19 7.91 5.4 18.65 16.79 16.75
3.00 14.37 8.09 5.58 18.86 17 16.9
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 271
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) 6-7 Lobe 6.0 Stage SERIES 1
272 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 9 5/8 in (244 mm) 6-7 Lobe 6.0 STAGE SERIES 1
B 200 18000
A (BIT TO BEND) (24404)
(BIT TO
STAB.) 17697
(23994)
(7171)
1200 GPM (4542 LPM)
1040
15000
(20337)
150
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm
100 9000
Bit Box Connection 6-5/8 or 7-5/8 REGULAR 600 GPM (2271 LPM)
70%
Bearing Load - Off Bottom RQ
Static 852600 lbf 379260 daN TO
(4067)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.49 2.98 3.58 1.25 3.53 - - 5.73 6.82 7.41
0.78 1 - - 3.23 4.72 5.32 1.50 4.88 - - 7.31 7.93 8.53
1.15 2.99 - - 5.1 6.37 6.97 1.75 6.22 0.57 - 8.89 9.04 9.64
1.50 4.88 - - 7.31 7.93 8.53 2.00 7.57 1.91 - 10.47 10.16 10.75
1.83 6.65 1 - 9.4 9.4 10
2.12 8.21 2.56 0.3 11.23 10.69 11.29
2.38 9.61 3.96 1.7 12.87 11.85 12.45
2.60 10.79 5.14 2.88 14.26 12.83 13.43
2.77 11.71 6.05 3.79 15.34 13.85 14.18
2.90 12.4 6.75 4.49 16.16 14.67 14.76
2.97 12.78 7.13 4.87 16.6 15.11 15.07
3.00 12.94 7.29 5.03 16.79 15.3 15.21
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 273
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) 6-7 Lobe 6.0 Stage HR SERIES 1
274 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 9 5/8 in (244 mm) 6-7 Lobe 6.0 STAGE HR SERIES 1
B 200 30000
A (BIT TO BEND) (40674)
(BIT TO
STAB.) 27120
(36769)
1200 GPM (4542 LPM) 25000
(10756)
(33895)
1560
150
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm
100 15000
Bit Box Connection 6-5/8 or 7-5/8 REGULAR
600 GPM (2271 LPM) (20337)
Dynamic 240975 lbf 107190 daN
Bearing Load On Bottom
70%
Bearing Load - Off Bottom UE
Static 852600 lbf 379260 daN RQ (6779)
TO
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 1235100 lbf 549000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 6-7 Lobe 6.0 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.13 rev/gal 0.03 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 1,560 psi 10,756 kPa 600 2,271 42 - 40
C = Overall Length 408.7 in 10381 mm Max Torque @ No Load 27,120 ft-lbs 36,770 Nm 900 3,407 83 - 100
Weight 6085 lbs 2760.1 kg Max Power 635 HP 474 kW 1,200 4,542 123 - 160
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) 6-7 Lobe 6.0 Stage HR SERIES 1 FBH BUILD RATE: 9-5/8 in (244 mm) 6-7 Lobe 6.0 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.49 2.98 3.58 1.25 3.53 - - 5.73 6.82 7.41
0.78 1 - - 3.23 4.72 5.32 1.50 4.88 - - 7.31 7.93 8.53
1.15 2.99 - - 5.1 6.37 6.97 1.75 6.22 0.57 - 8.89 9.04 9.64
1.50 4.88 - - 7.31 7.93 8.53 2.00 7.57 1.91 - 10.47 10.16 10.75
1.83 6.65 1 - 9.4 9.4 10
2.12 8.21 2.56 0.3 11.23 10.69 11.29
2.38 9.61 3.96 1.7 12.87 11.85 12.45
2.60 10.79 5.14 2.88 14.26 12.83 13.43
2.77 11.71 6.05 3.79 15.34 13.85 14.18
2.90 12.4 6.75 4.49 16.16 14.67 14.76
2.97 12.78 7.13 4.87 16.6 15.11 15.07
3.00 12.94 7.29 5.03 16.79 15.3 15.21
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 275
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) 7-8 Lobe 5.7 Stage HR SERIES 1
276 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 9 5/8 in (244 mm) 7-8 Lobe 5.7 STAGE HR SERIES 1
B 160
A (BIT TO BEND) 1200 GPM (4542 LPM)
(BIT TO 27000
STAB.)
(36607)
25920
(35143)
(9239)
22500
1340
120 900 GPM (3407 LPM)
(30506)
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm (24405)
80
Bit Box Connection 6-5/8 or 7-5/8 REGULAR 600 GPM (2271 LPM)
13500
Dynamic 240975 lbf 107190 daN (18304)
Bearing Load On Bottom
70%
Static UE 4500
852600 lbf 379260 daN RQ (6101)
TO
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 200 400 600 800 1000 1200 1400 1600
Absolute Overpull 1235100 lbf 549000 daN (1379) (2758) (4137) (5516) (6895) (8274) (9653) (11032)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 7-8 Lobe 5.7 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.13 rev/gal 0.03 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 1,340 psi 9,239 kPa 600 2,271 52 - 80
C = Overall Length 398.7 in 10127 mm Max Torque @ No Load 25,920 ft-lbs 35,143 Nm 900 3,407 90 - 115
Weight 6326 lbs 2869.4 kg Max Power 632 HP 471 kW 1,200 4,542 128 - 150
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) 7-8 Lobe 5.7 Stage HR SERIES 1 FBH BUILD RATE: 9-5/8 in (244 mm) 7-8 Lobe 5.7 Stage HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.54 3.11 3.73 1.25 3.62 - - 5.87 7.01 7.64
0.78 1.03 - - 3.31 4.88 5.50 1.50 4.99 - - 7.49 8.15 8.77
1.15 3.07 - - 5.22 6.56 7.18 1.75 6.37 0.58 - 9.12 9.28 9.91
1.50 4.99 - - 7.49 8.15 8.77 2.00 7.75 1.96 - 10.74 10.42 11.04
1.83 6.81 1.02 - 9.64 9.65 10.27 2.25 9.13 3.34 1.02 12.37 11.55 12.18
2.12 8.41 2.62 0.31 11.52 10.96 11.59 2.50 10.50 4.71 2.40 13.99 12.69 13.31
2.38 9.84 4.05 1.74 13.21 12.14 12.77
2.60 11.05 5.26 2.95 14.64 13.14 13.76
2.77 11.99 6.20 3.89 15.75 14.18 14.54
2.90 12.70 6.92 4.60 16.59 15.02 15.13
2.97 13.09 7.30 4.99 17.05 15.48 15.44
3.00 13.25 7.47 5.15 17.24 15.67 15.58
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 277
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe 4.0 Stage HR SERIES 1
278 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 6-7 Lobe 4.0 STAGE HR SERIES 1
B 180 13820
A (BIT TO BEND) (18737)
(6481)
(BIT TO
940
STAB.) 160 900 GPM (3407 LPM) 16000
(21693)
140 14000
(18981)
120
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm 100 10000
(13558)
Bit Box Connection 6-5/8 or 7-5/8 REGULAR
70%
(5423)
Bearing Load - Off Bottom UE
Static 852600 lbf 379260 daN 20 RQ 2000
TO (2712)
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 200 400 600 800 1000 1200
Absolute Overpull 1235100 lbf 549000 daN (1379) (2758) (4137) (5516) (6895) (8274)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 6-7 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.17 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 940 psi 6,481 kPa 400 1,514 51 - 68
C = Overall Length 364.7 in 9263 mm Max Torque @ No Load 13,820 ft-lbs 18,737 Nm 650 2,461 94 - 111
Weight 4831 lbs 2191.3 kg Max Power 358 HP 267 kW 900 3,407 136 - 153
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 6-7 Lobe 4.0 Stage
4.0 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.73 3.61 4.36 1.25 3.94 - - 6.40 7.77 8.52
0.78 1.12 - - 3.62 5.50 6.25 1.50 5.44 - - 8.19 8.98 9.73
1.15 3.34 - - 5.68 7.29 8.04 1.75 6.94 0.64 - 9.99 10.19 10.94
1.50 5.44 - - 8.19 8.98 9.73 2.00 8.44 2.14 - 11.79 11.40 12.15
1.83 7.42 1.12 - 10.57 10.58 11.33
2.12 9.16 2.86 0.33 12.65 11.98 12.73
2.38 10.72 4.42 1.89 14.52 13.24 13.99
2.60 12.04 5.74 3.21 16.10 14.31 15.05
2.77 13.06 6.76 4.23 17.32 15.44 15.88
2.90 13.84 7.54 5.01 18.25 16.38 16.51
2.97 14.26 7.96 5.43 18.76 16.88 16.84
3.00 14.44 8.14 5.61 18.97 17.10 16.99
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 279
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.4 Stage HR SERIES 1
280 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 3.4 STAGE HR SERIES 1 22530
B 90 (30547)
A (BIT TO BEND)
(BIT TO 600 GPM (2271 LPM) 25000
STAB.) 80 (33895)
(5516)
70
800
20000
(27116)
60 450 GPM (1703 LPM)
70%
(6779)
852600 lbf 379260 daN 10 RQ
TO
Max. Overpull for Re-run 741100 lbf 330000 daN 0
0 100 200 300 400 500 600 700 800 900 1000
Absolute Overpull 1235100 lbf 549000 daN (690) (1379) (2069) (2578) (3448) (4137) (4827) (5516) (6506) (6895)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 7-8 Lobe 3.4 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.09 rev/gal 0.02 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 800 psi 5,516 kPa 400 1,514 27 - 36
C = Overall Length 361.7 in 9187 mm Max Torque @ No Load 22,530 ft-lbs 30,547 Nm 650 2,461 50 - 59
Weight 4943 lbs 2242.1 kg Max Power 309 HP 230 kW 900 3,407 72 - 81
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 3.4 Stage
3.4 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.75 3.66 4.42 1.25 3.97 - - 6.45 7.85 8.61
0.78 1.13 - - 3.65 5.56 6.32 1.50 5.48 - - 8.26 9.06 9.83
1.15 3.37 - - 5.72 7.36 8.12 1.75 7.00 0.64 - 10.08 10.28 11.04
1.50 5.48 - - 8.26 9.06 9.83 2.00 8.51 2.15 -0.39 11.89 11.50 12.26
1.83 7.48 1.12 - 10.66 10.67 11.43
2.12 9.24 2.88 0.34 12.76 12.08 12.84
2.38 10.81 4.45 1.91 14.65 13.35 14.11
2.60 12.14 5.78 3.24 16.24 14.42 15.18
2.77 13.17 6.81 4.27 17.47 15.57 16.01
2.90 13.95 7.60 5.05 18.42 16.51 16.64
2.97 14.37 8.02 5.48 18.92 17.02 16.98
3.00 14.56 8.20 5.66 19.14 17.23 17.13
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 281
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 4.0 Stage HR SERIES 1
282 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 8 in (203 mm) 7-8 Lobe 4.0 STAGE HR SERIES 1
B 180
(6481)
A (BIT TO BEND)
940
(BIT TO 18000
STAB.) 160 (33895)
900 GPM (3407 LPM) 14830
140 (20107)
14000
120
SPEED (RPM)
Bit Size Range 12-1/4 - 17-1/2 in 311 - 445 mm 100
10000
Bit Box Connection 6-5/8 or 7-5/8 REGULAR (20337)
70%
TO (6780)
Max. Overpull for Re-run 741100 lbf 330000 daN 0
100 200 300 400 500 600 700 800 900 1000
0
(689) (1379) (2068) (2758) (3447) (4137) (4826) (5516) (6205) (6895)
Absolute Overpull 1235100 lbf 549000 daN
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 60000 ft-lbs 81349 Nm
A = Bit To Stabilizer (center) 20.2 in 513 mm
Lobe Configuration 7-8 Lobe 4.0 Stage HR Flow Rate Speed
Adjustable 87.3 in 2217 mm
B = Bit to Bend Displacement 0.16 rev/gal 0.04 rev/l GPM LPM RPM
Fixed 87.3 in 2217 mm
Max Differential @ No Load 940 psi 6,481 kPa 400 1,514 48 - 64
C = Overall Length 458.7 in 11651 mm Max Torque @ No Load 14,830 ft-lbs 20,107 Nm 650 2,461 88 - 104
Weight 5812 lbs 2636.3 kg Max Power 361 HP 270 kW 900 3,407 128 - 144
ADJUSTABLE BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe FBH BUILD RATE: 9-5/8 in (244 mm) Bottom w/ 8 in (203 mm) 7-8 Lobe 4.0 Stage
4.0 Stage HR SERIES 1 HR SERIES 1
SLICK STABILIZED SLICK STABILIZED
Hole Hole
Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2 Size 12-1/4 16 17-1/2 12-1/4 16 17-1/2
(311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm) (311 mm) (406 mm) (445 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m) BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE ANGLE
0.39 - - - 1.28 2.46 2.94 1.25 3.16 - - 5.12 5.98 6.45
0.78 0.90 - - 2.88 4.06 4.53 1.50 4.36 - - 6.51 7.00 7.47
1.15 2.68 - - 4.56 5.57 6.04 1.75 5.56 0.51 - 7.90 8.02 8.49
1.50 4.36 - - 6.51 7.00 7.47 2.00 6.77 1.71 - 9.29 9.04 9.51
1.83 5.95 0.89 - 8.34 8.34 8.82
2.12 7.34 2.29 0.27 9.96 9.53 10.00
2.38 8.59 3.54 1.52 11.40 10.59 11.06
2.60 9.65 4.60 2.58 12.62 11.49 11.96
2.77 10.47 5.42 3.39 13.57 12.39 12.65
2.90 11.09 6.04 4.02 14.29 13.11 13.18
2.97 11.43 6.38 4.35 14.68 13.50 13.47
3.00 11.58 6.52 4.50 14.85 13.67 13.59
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 283
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
11-1/4 in (286 mm) 5-6 Lobe 4.6 Stage SERIES 1
284 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 11 1/4 in (286 mm) 5-6 4.6 STAGE SERIES 1
B 200 25000
A (BIT TO BEND) (33895)
(BIT TO
STAB.) 180 1800 GPM (6831 LPM) 21800
(4760)
(29560)
690
160 20000
(27116)
140
SPEED (RPM)
120 15000
Bit Size Range 12-1/4 - 36 in 311 - 914 mm (20377)
Bit Box Connection 7-5/8 REGULAR 100
70%
Static 1376000 lbf 612080 daN 20 RQ
TO
Max. Overpull for Re-run 784500 lbf 349000 daN 0
0 200 400 600 800
Absolute Overpull 1307500 lbf 582000 daN (1379) (2578) (4137) (5516)
DIFFERENTIAL PRESSURE PSI (kPa) Performance Based on Water at 70°F (21°C)
Adjustable Make Up Torque 75000 ft-lbs 101686 Nm
A = Bit To Stabilizer (center) 22 in 559 mm
Lobe Configuration 5-6 Lobe 4.6 Stage Flow Rate Speed
Adjustable 94 in 2388 mm
B = Bit to Bend Displacement 0.09 rev/gal 0.02 rev/l GPM LPM RPM
Fixed N/A N/A
Max Differential @ No Load 690 psi 4,757 kPa 800 3,028 55 - 71
C = Overall Length 397.3 in 10091 mm Max Torque @ No Load 21,800 ft-lbs 29,557 Nm 1,300 4,921 98 - 121
Weight 8202 lbs 3720.4 kg Max Power 581 HP 433 kW 1,800 6,814 140 - 170
ADJUSTABLE BUILD RATE: 11-1/4 in (286 mm) 5-6 Lobe 4.6 Stage SERIES 1
SLICK STABILIZED
Hole
Size 16 17-1/2 26 36 16 17-1/2 26 36
(406 mm) (445 mm) (610 mm) (914 mm) (406 mm) (445 mm) (610 mm) (914 mm)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
0.39 - - - - 3.22 3.85 7.41 11.6
0.78 - - - - 4.95 5.58 9.14 13.33
1.15 0.34 - - - 6.6 7.22 10.79 14.97
1.50 2.27 0.16 - - 8.15 8.78 12.34 16.51
1.83 4.08 1.97 - - 9.98 10.25 13.8 17.97
2.12 5.67 3.56 - - 11.88 11.53 15.09 19.25
2.38 7.09 4.99 - - 13.58 12.95 16.24 20.4
2.60 8.3 6.19 - - 15.02 14.39 17.22 21.37
2.77 9.23 7.13 - - 16.14 15.51 17.97 22.12
2.90 9.95 7.84 - - 16.99 16.36 18.54 22.7
2.97 10.33 8.22 - - 17.45 16.82 18.85 23.01
3.00 10.49 8.39 - - 17.64 17.01 18.99 23.14
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 285
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
11-1/4 in (286 mm) 5-6 Lobe 4.6 Stage HR SERIES 1
286 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 11 1/4 in (286 mm) 5-6 4.6 STAGE HR SERIES 1
B
A (BIT TO BEND) 35000
(BIT TO (47453)
STAB.)
1800 GPM (6831 LPM) 32700
160 (44335)
28000
(37962)
1040
120
SPEED (RPM)
Bit Size Range 12-1/4 - 36 in 311 - 914 mm 21000
(28472)
Bit Box Connection 7-5/8 REGULAR
70%
Static 1376000 lbf 612080 daN RQ
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
0.39 - - - - 3.22 3.85 7.41 11.6
0.78 - - - - 4.95 5.58 9.14 13.33
1.15 0.34 - - - 6.6 7.22 10.79 14.97
1.50 2.27 0.16 - - 8.15 8.78 12.34 16.51
1.83 4.08 1.97 - - 9.98 10.25 13.8 17.97
2.12 5.67 3.56 - - 11.88 11.53 15.09 19.25
2.38 7.09 4.99 - - 13.58 12.95 16.24 20.4
2.60 8.3 6.19 - - 15.02 14.39 17.22 21.37
2.77 9.23 7.13 - - 16.14 15.51 17.97 22.12
2.90 9.95 7.84 - - 16.99 16.36 18.54 22.7
2.97 10.33 8.22 - - 17.45 16.82 18.85 23.01
3.00 10.49 8.39 - - 17.64 17.01 18.99 23.14
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 287
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
11-1/4 in (286 mm) 6-7 Lobe 5.0 Stage HR SERIES 1- 9 5/8 in (244 mm) Rotor
288 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 11 1/4 in (286 mm) 6-7 5.0 STAGE HR SERIES 1 26610
B 180
A (BIT TO BEND) (36078)
(BIT TO 1300 GPM (4921 LPM)
STAB.) 23860
(32350)
(8136)
1180
20690
140
(28052)
950 GPM (3596 LPM)
70%
20
TO (4000)
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
0.39 - - - - 3.38 4.05 7.85 12.30
0.78 - - - - 5.15 5.82 9.61 14.06
1.15 0.36 - - - 6.83 7.50 11.29 15.74
1.50 2.33 0.16 - - 8.42 9.09 12.88 17.32
1.83 4.20 2.03 - - 10.32 10.59 14.37 18.81
2.12 5.84 3.67 - - 12.28 11.91 15.69 20.12
2.38 7.31 5.14 - - 14.05 13.38 16.86 21.29
2.60 8.55 6.38 - - 15.54 14.87 17.86 22.28
2.77 9.51 7.34 - - 16.69 16.02 18.63 23.05
2.90 10.24 8.07 - - 17.57 16.90 19.22 23.63
2.97 10.64 8.47 - - 18.05 17.38 19.53 23.95
3.00 10.81 8.64 - - 18.25 17.58 19.67 24.09
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 289
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
11-1/4 in (286 mm) 6-7 Lobe 5.5 Stage HR SERIES 1
290 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
C
(OVERALL LENGTH) 11 1/4 in (286 mm) 6-7 5.5 STAGE HR SERIES 1 50000
B 200
A (BIT TO BEND) (67791)
(BIT TO
(8687)
STAB.)
1260
1800 GPM (6831 LPM) 40000
150 (54233)
37640
SPEED (RPM)
Bit Size Range 12-1/4 - 36 in 311 - 914 mm (40675)
Bit Box Connection 7-5/8 REGULAR 100
900 GPM (3407 LPM)
70%
TO
BEND Degrees per 100 Feet (30 m) Degrees per 100 Feet (30 m)
ANGLE
0.39 -3.65 -5.66 - - 2.97 3.54 6.77 10.56
0.78 -1.61 -3.62 - - 4.64 5.21 8.44 12.23
1.15 0.33 -1.68 - - 6.23 6.80 10.03 13.81
1.50 2.16 0.15 - - 7.73 8.30 11.53 15.31
1.83 3.89 1.88 - - 9.46 9.72 12.94 16.72
2.12 5.41 3.40 - - 11.26 10.96 14.18 17.96
2.38 6.77 4.76 - - 12.87 12.30 15.29 19.07
2.60 7.92 5.91 - - 14.23 13.66 16.24 20.00
2.77 8.81 6.80 - - 15.29 14.72 16.96 20.73
2.90 9.49 7.48 - - 16.09 15.52 17.52 21.28
2.97 9.86 7.85 - - 16.53 15.96 17.82 21.58
3.00 10.01 8.00 - - 16.71 16.14 17.95 21.71
Possible damage may occur when motor is run higher than 70% of Maximum Differential Pressure.
This information is for reference only. Build rates are theoretical calculations using three-
point geometry and new motor builds. Actual rate predictions will depend on formation 291
OIL SEALED MUD MOTORS
characteristics, bit profiles, and WOB.
For custom motor configurations and build rates, please contact your DYNOMAX office.
OPTIONAL EQUIPMENT
292 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
OFFSET FLEX SUB w/ BUTTONS & HARDBANDING DUMP SUB WITH FLOAT BORE w/ HARDBANDING
SCREW-ON KICK PAD SCREW-ON SPIRAL STABILIZER
SCREW-ON STABILIZER
293
DYNOMAX OIL-SEALED MOTORS
DYNOMAX OIL-SEALED MOTOR CONNECTION TORQUES
294 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
CONNECTION (ft·lbs) 2-7/8" 3-1/8" 3-3/4" 5" 6-1/2" 6-1/2" 6-1/2" 6-3/4" 6-3/4" 7" 8” 9-5/8" 11-1/4"
SERIES # 1 1 1 2 1 2 SHORT 3 1 3 3 1&2 1 1
End Cap 2000 2000 3000 10000 18000 24500 24500 18000 24500 24500 26000 35000 35000
Body Connection 2000 3000 4500 12000 25000 22000 22000 25000 22000 32000 40000 60000 75000
Mandrel to Washpipe 2000 1250 2500 13500 15000 17000 17000 15000 17000 24000 20000 35000 50000
Drive Shaft to Washpipe 1800 1000 2000 11000 12500 15000 15000 12500 15000 20000 16000 25000 40000
Drive Shaft to Rotor 1500 1000 2000 6000 12500 12500 12500 12500 12500 14000 16000 25000 40000
Adaptor Cap 750 750 1250 2000 5000 5000 5000 5000 5000 5000 6000 8000 8000
Adjustable Mandrel N/A 2500 3500 12000 25000 25000 25000 25000 25000 25000 40000 60000 75000
Stabilizer N/A N/A 3500 8000 12000 12000 12000 12000 12000 15000 30000 38000 50000
Rotor Catcher to Rotor 500 500 500 1250 2500 2500 2500 2500 2500 2500 3500 3500 4500
CONNECTION (N·m) 2-7/8" 3-1/8" 3-3/4" 5" 6-1/2" 6-3/4" 6-1/2" 6-3/4" 6-3/4" 7" 8” 9-5/8" 11-1/4"
SERIES # 1 1 1 2 1 2 SHORT 3 1 3 3 1&2 1 1
End Cap 2710 2710 4070 13560 24400 33220 33220 24400 33220 33220 35250 47450 47450
Body Connection 2710 4070 6100 16270 33900 29830 29830 33900 29830 43390 54230 81350 101690
Mandrel to Washpipe 2710 1690 3390 18300 20340 23050 23050 20340 23050 32540 27120 47450 67790
Drive Shaft to Washpipe 2440 1360 2710 14910 16950 20340 20340 16950 20340 27120 21690 33900 54230
Drive Shaft to Rotor 2030 1360 2710 8130 16950 16950 16950 16950 16950 18980 21690 33900 54230
Adaptor Cap 1020 1020 1690 2710 6780 6780 6780 6780 6780 6780 8130 10850 10850
Adjustable Mandrel N/A 3390 4750 16270 33900 33900 33900 33900 33900 33900 54230 81350 101690
Stabilizer N/A N/A 4750 10850 16270 16270 16270 16270 16270 20340 40670 51520 67790
Rotor Catcher to Rotor 680 680 680 1690 3390 3390 3390 3390 3390 3390 4750 4750 6100
295
DYNOMAX OIL-SEALED MOTORS
DYNOMAX SHOCK SUBS
296 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
2. The disk springs configuration paired with hydraulic dampening system yields maximum bit performance.
3. The Shock Sub is preset to partial compression, thus enabling compensation in both up and downwards direction as required.
4. Before Installing the Shock Sub in the drill string, make sure the threaded connections are thoroughly cleaned and free of any debris.
5. The Shock Sub must be installed in the drill string with Mandrel end down.
6. Protect the mandrel sealing surface from any kind of damage while operating or handling process.
7. Apply Rig tongs adjacent to the top and bottom connections of the sub to avoid over torquing or breaking any body connections.
8. Avoid breaking any body connections at the rig, this should be only carried out at service centers when the tool is due for service.
9. Common practice is to place the Shock Sub next to the bit. This placement will help to minimize the oscillating mass and an Optimum
performance from the Shock Sub can be achieved.
10. Placing Shock Sub further up the assembly should any other Operating conditions arise may reduce the tool effectiveness because of greater
oscillating mass.
11. It is advisable not to run Shock Subs with standard seal kit above 275°F (135°C).
Optional High Temp seals may be requested while ordering the Sub 350°F (175°C).
12. Dynomax recommends a maximum of 250 hrs. of operation before being serviced.
Optimal WOB*
13. Check for any damage or wear once the Sub is pulled out of the hole. Contact Service Shock Sub Size lbf (daN)
center if in doubt. Example: Chrome surface, Wiper seal- for oil leaks etc. 2 7/8" 6158 (2739)
14. Check for any free play when the Sub is out of the hole. Contact Service center if in 3 1/8" 6158 (2739)
doubt. Example: In Neutral position, apply a “mark” with a paint pen where the wiper 3 3/4" 6849 (3049)
seal sits (Mandrel and splined housing end). Apply some push/pull load to the sub 4 3/4" - 5" 19272 (8572)
as you would when in a drill string, now release the applied load, the mandrel should
6 1/2" - 6 3/4" 35831 (15938)
return back to its neutral position and wiper seal should align with the same “mark”
made before applying the load. 8" 56447 (25108)
9 1/2" 92977 (41358)
15. Clean the Shock Sub with fresh water, flush out all the drilling fluid to avoid any
hydraulic contamination. 11 1/4" 124790 (55509)
*Optimal WOB may vary with operating conditions.
16. Apply thread protectors when the Shock Sub is not in use. Different spring configurations for different sizes
available upon request.
17. If the Shock Sub is stored for longer durations, it is advisable to occasionally rotate
the Sub to a new position to avoid seals from settling.
297
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
298 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
287SS02 - 2 7/8 in (73 mm) Series 2 Spring 287SS02 - 2 7/8 in (73 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 2-3/8 PAC End Connections 2-3/8 PAC
Nominal Tool OD 2 7/8 in 73 mm Nominal Tool OD 2 7/8 in 73 mm
Nominal Tool ID 0.88 in 22 mm Nominal Tool ID 0.88 in 22 mm
Length 51.4 in 1,306 mm Length 51.4 in 1,306 mm
Weight 77 lbs 35 kg Weight 77 lbs 35 kg
Axial Load Capacity 9,475 lbf 4,210 daN Axial Load Capacity 9,475 lbf 4,210 daN
Spring Rate 8,000 lbs/in 1,400 N/mm Spring Rate 30,100 lbs/in 5,271 N/mm
Absolute Overpull 121,300 lbf 53,960 daN Absolute Overpull 121,300 lbf 53,960 daN
Max Torque 3,400 ft-lbs 4,610 Nm Max Torque 3,400 ft-lbs 4,610 Nm
Pump Open Area 2.49 in² 1,610 mm² Pump Open Area 2.49 in² 1,610 mm²
Opening Travel 0.89 in 22.61 mm Opening Travel 0.48 in 12.19 mm
Closing Travel 0.90 in 22.86 mm Closing Travel 0.48 in 12.19 mm
Total Travel 1.79 in 45.47 mm Total Travel 0.96 in 24.38 mm
312SS02 - 3 1/8in (79 mm) Series 2 Spring 312SS02 - 3 1/8in (79 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 2-3/8 REGULAR End Connections 2-3/8 REGULAR
Nominal Tool OD 3 1/8 in 95 mm Nominal Tool OD 3 1/8 in 95 mm
Nominal Tool ID 1.0 in 25.4 mm Nominal Tool ID 1.0 in 25.4 mm
Length 62.4 in 1,585 mm Length 62.4 in 1,585 mm
Weight 105 lbs 48 kg Weight 105 lbs 48 kg
Axial Load Capacity 10,000 lbf 4,448 daN Axial Load Capacity 10,000 lbf 4,448 daN
Spring Rate 9,000 lbs/in 1,576 N/mm Spring Rate 30,500 lbs/in 5,341 N/mm
Absolute Overpull 200,000 lbf 88,964 daN Absolute Overpull 200,000 lbf 88,964 daN
Max Torque 5,300 ft-lbs 7,186 Nm Max Torque 5,300 ft-lbs 7,186 Nm
Pump Open Area 2.80 in² 3,048 mm² Pump Open Area 2.80 in² 3,048 mm²
Opening Travel 1.01 in 25.65 mm Opening Travel 0.60 in 15.24 mm
Closing Travel 1.01 in 25.65 mm Closing Travel 0.60 in 15.24 mm
Total Travel 2.02 in 51.30 mm Total Travel 1.20 in 30.48 mm
299
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
300 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
375SS02 - 3 3/4 in (95 mm) Series 2 Spring 375SS02 - 3 3/4 in (95 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 2-7/8 REGULAR End Connections 2-7/8 REGULAR
Nominal Tool OD 3 3/4 in 95 mm Nominal Tool OD 3 3/4 in 95 mm
Nominal Tool ID 1.25 in 32 mm Nominal Tool ID 1.25 in 32 mm
Length 83.1 in 2,111 mm Length 83.1 in 2,111 mm
Weight 201 lbs 91 kg Weight 201 lbs 91 kg
Axial Load Capacity 10,538 lbf 4,690 daN Axial Load Capacity 10,538 lbf 4,690 daN
Spring Rate 6,000 lbs/in 1,050 N/mm Spring Rate 21,300 lbs/in 3,730 N/mm
Absolute Overpull 210,800 lbf 93,770 daN Absolute Overpull 210,800 lbf 93,770 daN
Max Torque 6,755 ft-lbs 9,159 Nm Max Torque 6,755 ft-lbs 9,159 Nm
Pump Open Area 4.69 in² 3030 mm² Pump Open Area 4.69 in² 3,030 mm²
Opening Travel 0.96 in 24.38 mm Opening Travel 0.85 in 21.59 mm
Closing Travel 1.50 in 38.10 mm Closing Travel 0.85 in 21.59 mm
Total Travel 2.46 in 62.48 mm Total Travel 1.70 in 43.18 mm
475SS02 - 4 3/4 in (121 mm) Series 2 Spring 475SS02 - 4 3/4 in (121 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 3-1/2 IF (NC38) End Connections 3-1/2 IF (NC38)
Nominal Tool OD 4 3/4 in 121 mm Nominal Tool OD 4 3/4 in 121 mm
Nominal Tool ID 1.75 in 44 mm Nominal Tool ID 1.75 in 44 mm
Length 93.2 in 2,367 mm Length 93.2 in 2,367 mm
Weight 365 lbs 165 kg Weight 365 lbs 165 kg
Axial Load Capacity 29,650 lbf 13,190 daN Axial Load Capacity 29,650 lbf 13,190 daN
Spring Rate 14,000 lbs/in 2,452 N/mm Spring Rate 50,250 lbs/in 8,800 N/mm
Absolute Overpull 352,500 lbf 156,800 daN Absolute Overpull 352,500 lbf 156,800 daN
Max Torque 10,625 ft-lbs 14,406 Nm Max Torque 10,625 ft-lbs 14,406 Nm
Pump Open Area 7.22 in² 4,660 mm² Pump Open Area 7.22 in² 4,660 mm²
Opening Travel 0.96 in 24.38 mm Opening Travel 0.96 in 24.38 mm
Closing Travel 1.81 in 45.97 mm Closing Travel 1.01 in 25.65 mm
Total Travel 2.77 in 70.35 mm Total Travel 2.02 in 51.03 mm
301
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
302 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
500SS02 - 5 in (127 mm) Series 2 Spring 500SS02 - 5 in (127 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 4 FH (NC40) End Connections 4 FH (NC40)
Nominal Tool OD 5 in 127 mm Nominal Tool OD 5 in 127 mm
Nominal Tool ID 1.75 in 44 mm Nominal Tool ID 1.75 in 44 mm
Length 93.2 in 2,367 mm Length 93.2 in 2367 mm
Weight 408 lbs 185 kg Weight 408 lbs 185 kg
Axial Load Capacity 29,650 lbf 13,190 daN Axial Load Capacity 29,650 lbf 13,190 daN
Spring Rate 14,000 lbs/in 2,452 N/mm Spring Rate 50,250 lbs/in 8,800 N/mm
Absolute Overpull 377,800 lbf 168,050 daN Absolute Overpull 377,800 lbf 168,050 daN
Max Torque 16,370 ft-lbs 22,195 Nm Max Torque 16,370 ft-lbs 22,195 Nm
Pump Open Area 7.22 in² 4,660 mm² Pump Open Area 7.22 in² 4,660 mm²
Opening Travel 0.98 in 24.89 mm Opening Travel 0.98 in 24.89 mm
Closing Travel 1.81 in 45.97 mm Closing Travel 1.01 in 25.65 mm
Total Travel 2.79 in 70.86 mm Total Travel 1.99 in 50.54 mm
650SS02 - 6 1/2 in (165 mm) Series 2 Spring 650SS02 - 6 1/2 in (165 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 4-1/2 XH (NC46) End Connections 4-1/2 XH (NC46)
Nominal Tool OD 6 1/2 in 165 mm Nominal Tool OD 6 1/2 in 165 mm
Nominal Tool ID 2.50 in 64 mm Nominal Tool ID 2.50 in 64 mm
Length 109.8 in 2,789 mm Length 109.8 in 2,789 mm
Weight 785 lbs 356 kg Weight 785 lbs 356 kg
Axial Load Capacity 55,125 lbf 24,520 daN Axial Load Capacity 55,125 lbf 24,520 daN
Spring Rate 23,900 lbs/in 4,186 N/mm Spring Rate 85,000 lbs/in 14,886 N/mm
Absolute Overpull 794,700 lbf 353,500 daN Absolute Overpull 794,700 lbf 353,500 daN
Max Torque 29,460 ft-lbs 39,942 Nm Max Torque 29,460 ft-lbs 39,942 Nm
Pump Open Area 14.73 in² 9,500 mm² Pump Open Area 14.73 in² 9,500 mm²
Opening Travel 1.46 in 37.08 mm Opening Travel 1.12 in 28.45 mm
Closing Travel 1.98 in 50.29 mm Closing Travel 1.12 in 28.45 mm
Total Travel 3.44 in 87.37 mm Total Travel 2.24 in 56.90 mm
303
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
304 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
650SS02 - 6 1/2 in (165 mm) LIGHT Series 2 Spring 650SS02 - 6 1/2 in (165 mm) LIGHT Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 4-1/2 XH (NC46) End Connections 4-1/2 XH (NC46)
Nominal Tool OD 6 1/2 in 165 mm Nominal Tool OD 6 1/2 in 165 mm
Nominal Tool ID 2.50 in 64 mm Nominal Tool ID 2.50 in 64 mm
Length 109.8 in 2,789 mm Length 109.8 in 2,789 mm
Weight 785 lbs 356 kg Weight 785 lbs 356 kg
Axial Load Capacity 55,125 lbf 24,520 daN Axial Load Capacity 55,125 lbf 24,520 daN
Spring Rate 8,600 lbs/in 1,506 N/mm Spring Rate 31,250 lbs/in 5,473 N/mm
Absolute Overpull 794,700 lbf 353,500 daN Absolute Overpull 794,700 lbf 353,500 daN
Max Torque 29,460 ft-lbs 39,942 Nm Max Torque 29,460 ft-lbs 39,942 Nm
Pump Open Area 14.73 in² 9,500 mm² Pump Open Area 14.73 in² 9,500 mm²
Opening Travel 1.46 in 37.08 mm Opening Travel 1.46 in 37.08 mm
Closing Travel 3.08 in 78.23 mm Closing Travel 1.71 in 43.43 mm
Total Travel 4.54 in 115.31 mm Total Travel 3.17 in 80.51 mm
675SS02 - 6 3/4 in (171 mm) Series 2 Spring 675SS02 - 6 3/4 in (171 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 4-1/2 IF (NC46) End Connections 4-1/2 IF (NC46)
Nominal Tool OD 6 3/4 in 171 mm Nominal Tool OD 6 3/4 in 171 mm
Nominal Tool ID 2.50 in 64 mm Nominal Tool ID 2.50 in 64 mm
Length 109.8 in 2,789 mm Length 109.8 in 2,789 mm
Weight 840 lbs 381 kg Weight 840 lbs 381 kg
Axial Load Capacity 55,125 lbf 24,520 daN Axial Load Capacity 55,125 lbf 24,520 daN
Spring Rate 23,900 lbs/in 4,186 N/mm Spring Rate 85,000 lbs/in 14,886 N/mm
Absolute Overpull 794,700 lbf 353,500 daN Absolute Overpull 794,700 lbf 353,500 daN
Max Torque 33,365 ft-lbs 45,237 Nm Max Torque 33,365 ft-lbs 45,237 Nm
Pump Open Area 14.73 in² 9,500 mm² Pump Open Area 14.73 in² 9,500 mm²
Opening Travel 1.46 in 37.08 mm Opening Travel 1.12 in 28.45 mm
Closing Travel 1.98 in 50.29 mm Closing Travel 1.12 in 28.45 mm
Total Travel 3.44 in 87.37 mm Total Travel 2.24 in 56.90 mm
305
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
306 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
675SS02 - 6 3/4 in (171 mm) LIGHT Series 2 Spring 675SS02 - 6 3/4 in (171 mm) LIGHT Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 4-1/2 IF (NC46) End Connections 4-1/2 IF (NC46)
Nominal Tool OD 6 3/4 in 171 mm Nominal Tool OD 6 3/4 in 171 mm
Nominal Tool ID 2.50 in 64 mm Nominal Tool ID 2.50 in 64 mm
Length 109.8 in 2,789 mm Length 109.8 in 2,789 mm
Weight 840 lbs 381 kg Weight 840 lbs 381 kg
Axial Load Capacity 55,125 lbf 24,520 daN Axial Load Capacity 55,125 lbf 24,520 daN
Spring Rate 8,600 lbs/in 1,506 N/mm Spring Rate 31,250 lbs/in 5,473 N/mm
Absolute Overpull 794,700 lbf 353,500 daN Absolute Overpull 794,700 lbf 353,500 daN
Max Torque 33,365 ft-lbs 45,237 Nm Max Torque 33,365 ft-lbs 45,237 Nm
Pump Open Area 14.73 in² 9,500 mm² Pump Open Area 14.73 in² 9,500 mm²
Opening Travel 1.46 in 37.08 mm Opening Travel 1.46 in 37.08 mm
Closing Travel 3.08 in 78.23 mm Closing Travel 1.71 in 43.43 mm
Total Travel 4.54 in 115.31 mm Total Travel 3.17 in 80.51 mm
800SS02 - 8 in (203 mm) Series 2 Spring 800SS02 - 8 in (203 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 6-5/8 REG End Connections 6-5/8 REG
Nominal Tool OD 8 in 203 mm Nominal Tool OD 8 in 203 mm
Nominal Tool ID 2.81 in 71 mm Nominal Tool ID 2.81 in 71 mm
Length 128.9 in 3,275 mm Length 128.9 in 3,275 mm
Weight 1,364 lbs 619 kg Weight 1,364 lbs 619 kg
Axial Load Capacity 86,842 lbf 38,630 daN Axial Load Capacity 86,842 lbf 38,630 daN
Spring Rate 28,000 lbs/in 4,904 N/mm Spring Rate 99,500 lbs/in 17,425 N/mm
Absolute Overpull 791,200 lbf 351,940 daN Absolute Overpull 791,200 lbf 351,940 daN
Max Torque 51,725 ft-lbs 70,130 Nm Max Torque 51,725 ft-lbs 70,130 Nm
Pump Open Area 24.58 in² 15,860 mm² Pump Open Area 24.58 in² 15,860 mm²
Opening Travel 1.46 in 37.08 mm Opening Travel 1.46 in 37.08 mm
Closing Travel 2.65 in 67.31 mm Closing Travel 1.50 in 38.1 mm
Total Travel 4.11 in 104.39 mm Total Travel 2.96 in 75.18 mm
307
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
308 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
800SS02 - 8 in (203 mm) LIGHT Series 2 Spring 800SS02 - 8 in (203 mm) LIGHT Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 6-5/8 REG End Connections 6-5/8 REG
Nominal Tool OD 8 in 203 mm Nominal Tool OD 8 in 203 mm
Nominal Tool ID 2.81 in 71 mm Nominal Tool ID 2.81 in 71 mm
Length 128.9 in 3,275 mm Length 128.9 in 3,275 mm
Weight 1,364 lbs 619 kg Weight 1,364 lbs 619 kg
Axial Load Capacity 86,842 lbf 38,630 daN Axial Load Capacity 86,842 lbf 38,630 daN
Spring Rate 10,000 lbs/in 1,751 N/mm Spring Rate 36,600 lbs/in 6,410 N/mm
Absolute Overpull 791,200 lbf 351,940 daN Absolute Overpull 791,200 lbf 351,940 daN
Max Torque 51,725 ft-lbs 70,130 Nm Max Torque 51,725 ft-lbs 70,130 Nm
Pump Open Area 24.58 in² 15,860 mm² Pump Open Area 24.58 in² 15,860 mm²
Opening Travel 1.46 in 37.08 mm Opening Travel 1.46 in 37.08 mm
Closing Travel 3.31 in 84.07 mm Closing Travel 1.83 in 46.48 mm
Total Travel 4.77 in 121.15 mm Total Travel 3.29 in 83.56 mm
950SS02 - 9 1/2 in (241 mm) Series 2 Spring 950SS02 - 9 1/2 in (241 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 7-5/8 REG End Connections 7-5/8 REG
Nominal Tool OD 9 1/2 in 241 mm Nominal Tool OD 9 1/2 in 241 mm
Nominal Tool ID 3.00 in 76 mm Nominal Tool ID 3.00 in 76 mm
Length 160.2 in 4,070 mm Length 160.2 in 4,070 mm
Weight 2,476 lbs 1,123 kg Weight 2,476 lbs 1,123 kg
Axial Load Capacity 143,043 lbf 63,630 daN Axial Load Capacity 143,043 lbf 63,630 daN
Spring Rate 33,850 lbs/in 5,928 N/mm Spring Rate 120,400 lbs/in 21,085 N/mm
Absolute Overpull 1,570,700 lbf 698,680 daN Absolute Overpull 1,570,700 lbf 698,680 daN
Max Torque 93,010 ft-lbs 126,105 Nm Max Torque 93,010 ft-lbs 126,105 Nm
Pump Open Area 34.33 in² 22,150 mm² Pump Open Area 34.33 in² 22,150 mm²
Opening Travel 2.39 in 60.71 mm Opening Travel 2.03 in 51.56 mm
Closing Travel 3.60 in 91.44 mm Closing Travel 2.03 in 51.56 mm
Total Travel 5.99 in 152.15 mm Total Travel 4.06 in 103.12 mm
309
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUBS
310 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
950SS02 - 9 1/2 in (241 mm) LIGHT Series 2 Spring 950SS02 - 9 1/2 in (241 mm) LIGHT Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 7-5/8 REG End Connections 7-5/8 REG
Nominal Tool OD 9 1/2 in 241 mm Nominal Tool OD 9 1/2 in 241 mm
Nominal Tool ID 3.00 in 76 mm Nominal Tool ID 3.00 in 76 mm
Length 160.2 in 4,070 mm Length 160.2 in 4,070 mm
Weight 2,476 lbs 1,123 kg Weight 2,476 lbs 1,123 kg
Axial Load Capacity 143,043 lbf 63,630 daN Axial Load Capacity 143,043 lbf 63,630 daN
Spring Rate 18,400 lbs/in 3,222 N/mm Spring Rate 69,900 lbs/in 12,241 N/mm
Absolute Overpull 1,570,700 lbf 698,680 daN Absolute Overpull 1,570,700 lbf 698,680 daN
Max Torque 93,010 ft-lbs 126,105 Nm Max Torque 93,010 ft-lbs 126,105 Nm
Pump Open Area 34.33 in² 22,150 mm² Pump Open Area 34.33 in² 22,150 mm²
Opening Travel 2.39 in 60.71 mm Opening Travel 1.88 in 47.75 mm
Closing Travel 3.43 in 87.12 mm Closing Travel 1.88 in 47.75 mm
Total Travel 5.82 in 147.83 mm Total Travel 3.76 in 95.50 mm
1125SS02 - 11 1/4 in (286 mm) Series 2 Spring 1125SS02 - 11 1/4 in (286 mm) Series 2 Spring
Configuration 1X1 Configuration 2X2
End Connections 7-5/8 REG End Connections 7-5/8 REG
Nominal Tool OD 11 1/4 in 286 mm Nominal Tool OD 11 1/4 in 286 mm
Nominal Tool ID 3.50 in 89 mm Nominal Tool ID 3.50 in 89 mm
Length 178.3 in 4,528 mm Length 178.3 in 4,528 mm
Weight 3,796 lbs 1,722 kg Weight 3,796 lbs 1,722 kg
Axial Load Capacity 191,985 lbf 85,400 daN Axial Load Capacity 191,985 lbf 85,400 daN
Spring Rate 36,350 lbs/in 6,366 N/mm Spring Rate 129,300 lbs/in 22,644 N/mm
Absolute Overpull 3,028,700 lbf 1,347,230 daN Absolute Overpull 3,028,700 lbf 1,347,230 daN
Max Torque 134,650 ft-lbs 182,561 Nm Max Torque 134,650 ft-lbs 182,561 Nm
Pump Open Area 43.96 in² 28,360 mm² Pump Open Area 43.96 in² 28,360 mm²
Opening Travel 2.36 in 59.94 mm Opening Travel 2.36 in 59.94 mm
Closing Travel 4.51 in 114.55 mm Closing Travel 2.55 in 64.77 mm
Total Travel 6.87 in 229.11 mm Total Travel 4.91 in 124.71 mm
311
DYNOMAX SHOCK SUBS
DYNOMAX SHOCK SUB CONNECTION TORQUES
CONNECTION
287SS-02 312SS-02 375SS-02 475SS-02 500SS-02 650SS-02 675SS-02 800SS-02 950SS-02 1125SS-02
(ft·lbs)
Body Connection 2500 3500 6000 10000 12000 22000 25000 40000 60000 75000
Mandrel to Lock Nut 860 850 1500 2500 2500 6000 6000 15000 20000 35000
CONNECTION
287SS-02 312SS-02 375SS-02 475SS-02 500SS-02 650SS-02 675SS-02 800SS-02 950SS-02 1125SS-02
(N·m)
Body Connection 3390 4745 8130 13560 16270 29830 33900 54230 81350 101690
Mandrel to Lock Nut 1170 1152 2030 3390 3390 8130 8130 20340 27120 47450
312
DYNOMAX SHOCK SUBS
DYNO-JAR™ OPERATING PROCEDURE
313 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
JARRING UP
Each DYNO-JAR™ is sent to the field with a preset latch up value and delay time.
Upwards pull force must be able to overcome the preset latch value plus the drill string weight above the jar plus any applicable hole drag.
When this value is exceeded, the mechanical latch releases and the hydraulic delay will engage. The hydraulic delay is adjustable from the service shop.
At the end of the hydraulic delay, the jar will fire in an upwards motion.
RESET UP JAR
If the jar fires too soon, it may not have been pushed down in the latch position.
After the jar has fired, set the drill string down on the jar to close the latch.
The jar should close at about 5,000 – 10,000 daN (11,240 - 22480 lbf) (calculation must take into account the drill string weight below the jar).
Repeat the jarring up and reset up operations as required.
JARRING DOWN
Each DYNO-JAR™ is sent from the factory with a preset latch value.
Apply weight on the jar that will exceed the preset latch down value (available from the service shop). Take into account any dog legs or other factor that may reduce
the effect of the weight getting to the jar.
The jar will fire downwards with no hydraulic delay.
314
DYNO-JAR™
DYNO-JAR™
315 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
DMJ650 DMJ675
TOOL OD 6.56 in 167 mm TOOL OD 6.81 in 173 mm
TOOL ID 2.563 in 65 mm TOOL ID 2.563 in 65 mm
LENGTH (LATCHED) 22.2 ft 6.78 m LENGTH (LATCHED) 22.2 ft 6.78 m
WEIGHT 2100 lbs 953 kg WEIGHT 2100 lbs 953 kg
MAX. PULL WHILE METERING 198000 lbf 88,075 daN MAX. PULL WHILE METERING 198000 lbf 88,075 daN
MAXIMUM OVERPULL 901000 lbf 400,785 daN MAXIMUM OVERPULL 843000 lbf 374,985 daN
YIELD TORQUE 37500 ft-lbs 50,910 Nm YIELD TORQUE 36300 ft-lbs 49,235 Nm
PUMP OPEN AREA 4.47 in² 28.8 cm PUMP OPEN AREA 4.47 in² 28.8 cm
FREE STROKE 8 in 203 mm FREE STROKE 8 in 203 mm
OVERALL STROKE 18 in 457 mm OVERALL STROKE 18 in 457 mm
MAX. OPERATING TEMP MAX. OPERATING TEMP
275 °F 135 °C 275 °F 135 °C
(REG) (REG)
MAX. OPERATING TEMP MAX. OPERATING TEMP
400 °F 204 °C 400 °F 204 °C
(HIGH) (HIGH)
DMJ800
TOOL OD 8.14 in 207 mm
TOOL ID 2.813 in 71 mm
LENGTH (LATCHED) 22.4 ft 6.83 m
WEIGHT 3100 lbs 1,406 kg
MAX. PULL WHILE METERING 251000 lbf 111,650 daN
MAXIMUM OVERPULL 1249000 lbf 555,583 daN
YIELD TORQUE 64600 ft-lbs 87,582 Nm
PUMP OPEN AREA 9.69 in² 62.5 cm
FREE STROKE 8 in 203 mm
OVERALL STROKE 18 in 457 mm
MAX. OPERATING TEMP 275 °F 135 °C
(REG) Torque Connections available on next page.
MAX. OPERATING TEMP 400 °F 204 °C
(HIGH)
316
DYNO-JAR™
DYNO-JAR™ CONNECTION TORQUES
317 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
318
DYNO-JAR™
DYNOMAX SLIDE REAMERS
319 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
The DYNOMAX Slide Reamer was designed primarily for reaming during sliding, however the tool’s design allows for a multitude of uses
including:
Stabilization: The Slide Reamer can be utilized similar to a string stabilizer to centralize the bottom hole assembly.
Friction Reduction: In horizontal applications, the Slide Reamer can be used to reduce drill string surface contact on the well bore, acting
as a friction reducing tool.
STANDARD reamer cutter
Hole Cleaning: The same unique rotating action that reams the hole also helps clean and
condition the well bore.
Cuttings Removal: The rotating action agitates cuttings that can settle on the low side of the
well bore, therefore aiding in removing accumulated cuttings.
BENEFITS
• Integral blade providing 360 degree wall contact DOUBLE ROW reamer cutter
• Cutters turn with each movement of drill string, I.e. Rotating, Sliding, Tripping
• Allows optimal fluid passage
• Designed to minimize failures at high stress points
• Two tools in one. Many different variations can be run on the same tool
• Sealed Bearing design
• More cutting surface area than the competitors
• Reduces torque and drag
DYNOMAX SLIDE REAMER FISHING DIMENSIONS
DynoMax SLIDE REAMER
A B C D E F G
REAMER bodies are now NOMINAL
available in NON-MAG 56 in 18.9 in 14.5 in 22.8 in 5.16 in 4.81 in 2.00 in
D 5¾ - 5⅞
material 1.42 m 0.48 m 0.37 m 0.58 m 131 mm 122 mm 51 mm
56 in 19.5 in 14.9 in 22.5 in 5.25 in 4.81 in 2.25 in
5⅞ - 6 1.42 m 0.50 m 0.38 m 0.57 m 133 mm 122 mm 57 mm
56 in 19.4 in 13.4 in 23.4 in 5.25 in 5.15 in 2.25 in
5⅞ - 6
E 1.42 m 0.49 m 0.34 m 0.59 m 133 mm 140 mm 57 mm
56 in 17.9 in. 16.3 in 21.9 in 5.50 in 4.81 in 2.25 in
6⅛ - 6¼ 1.42 m 0.45 m 0.41 m 0.56 m 140 mm 122 mm 57 mm
A C 56 in 16.9 in 18.1 in 20.9 in 6.13 in 4.81 in 2.25 in
6½ - 6⅝ 1.42 m 0.43 m 0.46 m 0.53 m 156 mm 122 mm 57 mm
64 in 21.9 in 17 in 25 in 7.13 in 6.25 in 2.75 in
7⅜ - 7⅞ 1.63 m 0.56 m 0.43 m 0.64 m 181 mm 159 mm 70 mm
F
67.5 in 23.9 in 20.1 in 23.1 in 7.50 in 6.81 in 2.50 in
8¼ - 8¾ 1.71 m 0.61 m 0.51 m 0.59 m 191 mm 173 mm 70 mm
66.5 in 20.8 in 24 in 21.8 in 8.63 in 6.81 in 2.50 in
B 9⅝ - 9⅞ 1.68 m 0.53 m 0.61 m 0.55 m 219 mm 173 mm 64 mm
77 in 25.8 in 25.5 in 25.6 in 10.13 in 8.00 in 3.00 in
THRU HOLE 12 - 12¼ 1.96 m 0.65 m 0.65 m 0.65 m 257 m 203 mm 76 mm
G
1028 in 32.3 in 40 in 30.8 in 16.00 in 9.50 in 3.00 in
17¼ - 17½ 2.61 m 0.82 m 1.02 m 0.78 m 406 mm 241 mm 76 mm
320
DYNOMAX SLIDE REAMERS
DYNOMAX REGULATOR™
321 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
Today’s drilling applications are becoming more challenging with deeper, longer and more complex
wells being drilled faster than ever before. One challenge is keeping the hole clean while drilling,
which is achieved with higher flow rates. These flow rates are limited by the power sections on the
motors and quite often lead to premature failure due to over-pumping.
The DynoMax REGULATOR™ employs a variable size exit orifice to actively moderate the flow
that goes through the motor continuously – extra fluid is vented out the side. The exit orifice is
controlled by a valve that measures the flow entering the motor. The valve mechanism responds
in milliseconds so that flow to the motor is always regulated.
BENEFITS
● Reduce stator failures due to over pumping
● Utilize optimal performance of the power section in motors
● Reduce washing out of components in the motor
● No need to drop balls or darts for activation
● Motor stalls are still visible at surface
● Applicable not only conventional drilling, but also coil tubing,
and completion operations
Tool OD Tool OD Pin ID Length Length Weight Weight Absolute Overpull
Configuration End Connections Pin ID (SI)
(US) (SI) (US) (US) (SI) (US) (SI) (US)
2-1/8 in (54 mm) Series 2 1-1/2 REG (1-1/2 MT) 2-1/8 in 54 mm 1.00 in 25 mm 43.5 in 1105 mm 30 lbs 14 kg 150,000 lbf
2-7/8 in (73 mm) Series 2 2-3/8 PAC 2-7/8 in 73 mm 1.13 in 29 mm 35.0 in 889 mm 55 lbs 25 kg 150,000 lbf
4-3/4 in (121 mm) Series 2 3-1/2 IF (NC38) 4-3/4 in 121 mm 2.75 in 70 mm 43.0 in 1092 mm 145 lbs 66 kg 750,000 lbf
6-1/2 in (165 mm) Series 2 4-1/2 XH (NC46) 6-1/2 in 165 mm 2.89 in 73 mm 45.0 in 1143 mm 325 lbs 147 kg 1,500,000 lbf
Absolute Overpull Max Torque Min Motor Min Motor Flow Max Motor Flow Max Motor Flow Max Pump Rate Max Pump
Max Torque (US)
(SI) (SI) Flow (US) (SI) (US) (SI) (US) Rate (SI)
66720 daN 1,700 ft-lbs 2305 Nm 30 gpm 110 lpm 100 gpm 380 lpm 100 gpm 380 lpm
66720 daN 2,000 ft-lbs 2712 Nm 21 gpm 80 lpm 158 gpm 600 lpm 315 gpm 1190 lpm
333620 daN 11,000 ft-lbs 14914 Nm 100 gpm 380 lpm 465 gpm 1760 lpm 630 gpm 2380 lpm
667230 daN 24,000 ft-lbs 32540 Nm 200 gpm 760 lpm 800 gpm 3030 lpm 920 gpm 3480 lpm
322
DYNOMAX REGULATOR™
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
323 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
L
K
J
I
H
G1 / G2
F1 / F2
E
D
C
B
A
M N O P Q R S1 / S2 T1 / T2 U V W X Y Z AA BB CC
ROTOR ADAPTOR UNDERCUT Ø
ROTOR CATCH FLOAT SUB END
PISTON HOUSING UPSET END
THREAD PROTECTOR START
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
324
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
325 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
3 ¾" 7-8 2.3 STAGE SERIES 1 12.0 18.7 20.7 27.8 36.0 41.5 55.0 50.6 55.2 70.4 67.3 196.3 211.4 234.7 3.6 3.8 2.8 3.8 4.3 3.8 3.8 4.0 3.8 4.0 3.8 1.4 2.7 1.9 1.9 2.3 3.8 4.0 3.8
3 ¾" 7-8 2.3 STAGE HR SERIES 1 12.0 18.7 20.7 27.8 36.0 41.5 55.0 50.6 55.2 70.4 67.3 196.3 211.4 234.7 3.6 3.8 2.8 3.8 4.3 3.8 3.8 4.0 3.8 4.0 3.8 1.4 2.7 1.9 1.9 2.3 3.8 4.0 3.8
5" IMPERIAL - USC (Lengths, Diameters = in.)
4 ¾" 7-8 3.8 STAGE HR SERIES 2
15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 255.1 264.2 295.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 3.0 3.0 4.8 4.8 4.8
(5" COMBO)
5" 4-5 6.0 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 249.1 264.2 295.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 2.9 5.0 5.3 5.0
5" 5-6 4.0 STAGE SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 205.1 217.2 248.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 2.8 5.0 5.3 5.0
5" 5-6 4.0 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 205.1 217.2 248.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 2.8 5.0 5.3 5.0
5" 5-6 6.7 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 318.1 327.2 358.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.9 3.1 5.0 5.3 5.0
5" 5-6 8.3 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 300.5 319.8 350.9 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 2.9 5.0 5.3 5.0
5" 6-7 6.0 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 256.6 262.2 293.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.9 3.0 5.0 5.3 5.0
5" 6-7 8.0 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 318.1 327.2 358.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.9 3.0 5.0 5.3 5.0
5" 7-8 2.0 STAGE SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 319.1 327.2 358.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 3.0 2.8 5.0 5.3 5.0
5" 7-8 2.6 STAGE HR NP SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 267.3 270.9 302.0 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 - - 5.0 5.3 5.0
5" 7-8 2.6 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 297.1 306.5 337.6 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 3.1 5.0 5.3 5.0
5" 7-8 3.7 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 291.9 312.2 343.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 3.1 3.1 5.0 5.3 5.0
ROTOR ADAPTOR UNDERCUT Ø
ROTOR CATCH FLOAT SUB END
PISTON HOUSING UPSET END
THREAD PROTECTOR START
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
5" 7-8 3.8 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 255.1 264.2 295.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 3.0 3.0 5.0 5.3 5.0
5" 7-8 4.5 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 297.1 306.5 337.6 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 3.1 5.0 5.3 5.0
5" 7-8 5.0 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 263.1 275.2 306.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 3.0 5.0 5.3 5.0
5" 8-9 6.0 STAGE HR SERIES 2 15.5 - 20.2 28.2 38.6 45.7 52.2 56.3 60.8 77.2 77.1 318.1 327.2 358.3 4.6 5.2 3.6 - 5.8 5.1 5.1 5.7 5.1 5.7 5.1 1.9 3.6 2.8 2.8 3.0 5.0 5.3 5.0
6 1/2" and 6 3/4" IMPERIAL - USC (Lengths, Diameters = in.)
6 ½ - 6 ¾" 4-5 7.0 STAGE HR
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 300.6 312.7 345.7 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.2 6.6 6.8 6.6
SERIES 1
6 ½ - 6 ¾" 6-7 5.0 STAGE HR
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 292.1 298.1 331.1 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.3 6.6 6.8 6.6
SERIES 1
6 ½ - 6 ¾" 7-8 2.0 STAGE HR
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 245.4 251.6 284.6 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.3 6.6 6.8 6.6
SERIES 1
6 ½ - 6 ¾" 7-8 2.9 STAGE HR
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 311.6 318.1 351.1 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.3 6.6 6.8 6.6
SERIES 1
6 ½ - 6 ¾" 7-8 3.0 STAGE
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 216.6 223.1 256.1 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.5 6.6 6.8 6.6
SERIES 1
6 ½ - 6 ¾" 7-8 3.0 STAGE HR
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 216.6 223.1 256.1 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.5 6.6 6.8 6.6
SERIES 1
6 ½ - 6 ¾" 7-8 3.0 STAGE HR
17.5 27.3 31.9 39.6 51.4 61.1 73.5 73.0 79.0 98.1 98.1 295.6 302.1 335.1 6.4 6.6 4.8 6.6 7.1 6.6 6.8 7.1 6.8 7.1 6.8 2.8 4.9 4.0 4.0 4.6 6.6 6.8 6.6
SLOW SERIES 1
326
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
327 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
328
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
329 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
330
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
331 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
8" 7-8 3.0 STAGE HR SERIES 1 20.3 32.9 38.6 46.6 62.6 72.3 93.6 87.0 93.7 115.2 114.0 267.6 275.2 312.7 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.2 8.0 8.3 8.0
8" 7-8 3.4 STAGE HR SERIES 1 20.3 32.9 38.6 46.6 62.6 72.3 93.6 87.0 93.7 115.2 114.0 407.0 415.2 452.7 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.3 8.0 8.3 8.0
8" 7-8 4.0 STAGE SERIES 1 20.3 32.9 38.6 46.6 62.6 72.3 93.6 87.0 93.7 115.2 114.0 310.5 321.2 358.7 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 7-8 5.9 STAGE SERIES 1 20.3 32.9 38.6 46.6 62.6 72.3 93.6 87.0 93.7 115.2 114.0 398.5 415.2 452.7 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 7-8 4.0 STAGE HR SERIES 1 20.3 32.9 38.6 46.6 62.6 72.3 93.6 87.0 93.7 115.2 114.0 310.5 321.2 358.7 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 4-5 5.3 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 322.7 330.9 368.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 5-6 3.0 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 206.7 214.4 251.9 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 5-6 3.0 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 206.7 214.4 251.9 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 6-7 4.0 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 300.7 308.9 346.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 6-7 4.0 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 300.7 308.9 346.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 6-7 5.0 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 345.7 352.9 390.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 6-7 5.0 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 345.7 352.9 390.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 7-8 2.0 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 255.3 270.9 308.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 7-8 3.0 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 255.3 262.9 300.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.2 8.0 8.3 8.0
8" 7-8 3.0 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 255.3 262.9 300.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.2 8.0 8.3 8.0
8" 7-8 3.4 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 394.7 402.9 440.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.3 8.0 8.3 8.0
8" 7-8 4.0 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 298.2 308.9 346.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
ROTOR ADAPTOR UNDERCUT Ø
ROTOR CATCH FLOAT SUB END
PISTON HOUSING UPSET END
THREAD PROTECTOR START
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
8" 7-8 4.0 STAGE HR SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 298.2 308.9 346.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 7-8 5.9 STAGE SERIES 2 16.3 27.4 32.4 40.3 50.4 60.1 81.3 74.7 81.4 102.9 101.7 386.2 402.9 440.4 7.8 8.0 6.3 8.0 8.8 8.0 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 4-5 5.3 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 323.8 330.8 368.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 5-6 3.0 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 207.8 214.3 251.8 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 5-6 3.0 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 207.8 214.3 251.8 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 6-7 4.0 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 301.8 308.8 346.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 6-7 4.0 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 301.8 308.8 346.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 6-7 5.0 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 346.8 352.8 390.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 6-7 5.0 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 346.8 352.8 390.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.0 8.0 8.3 8.0
8" 7-8 2.0 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 256.4 270.8 308.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.9 8.0 8.3 8.0
8" 7-8 3.0 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 256.4 262.8 300.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.2 8.0 8.3 8.0
8" 7-8 3.0 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 256.4 262.8 300.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.2 8.0 8.3 8.0
8" 7-8 3.4 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 395.8 402.8 440.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 5.3 8.0 8.3 8.0
8" 7-8 4.0 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 299.3 308.8 346.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 7-8 4.0 STAGE HR MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 299.3 308.8 346.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
8" 7-8 5.9 STAGE MUD LUBE 21.1 50.3 33.1 44.2 - 60.1 63.6 74.9 81.3 102.8 102.8 387.3 402.8 440.3 8.0 8.3 6.0 8.3 9.0 - 8.0 8.4 8.0 8.4 8.0 3.4 5.8 4.8 4.8 4.8 8.0 8.3 8.0
332
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
333 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
334
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - METRIC (SI)
335 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
L
K
J
I
H
G1 / G2
F1 / F2
E
D
C
B
A
M N O P Q R S1 / S2 T1 / T2 U V W X Y Z AA BB CC
ROTOR ADAPTOR UNDERCUT Ø
ROTOR CATCH FLOAT SUB END
PISTON HOUSING UPSET END
THREAD PROTECTOR START
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
336
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - METRIC (SI)
337 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
3 ¾" 7-8 2.3 STAGE SERIES 1 0.30 0.47 0.53 0.71 0.91 1.05 1.40 1.29 1.40 1.79 1.71 4.99 5.37 5.96 92.20 95.25 69.85 95.25 107.95 95.25 95.25 101.60 95.25 101.60 95.25 35.56 68.58 47.80 47.75 57.15 95.25 101.60 95.25
3 ¾" 7-8 2.3 STAGE HR SERIES 1 0.30 0.47 0.53 0.71 0.91 1.05 1.40 1.29 1.40 1.79 1.71 4.99 5.37 5.96 92.20 95.25 69.85 95.25 107.95 95.25 95.25 101.60 95.25 101.60 95.25 35.56 68.58 47.80 47.75 57.15 95.25 101.60 95.25
5" METRIC - SI (Lengths = m) (Diameters = mm)
4 ¾" 7-8 3.8 STAGE HR SERIES 2
0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 6.48 6.71 7.50 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 75.44 74.93 120.65 120.65120.65
(5" COMBO)
5" 4-5 6.0 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 6.33 6.71 7.50 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 69.85 73.96 127.00 133.35127.00
5" 5-6 4.0 STAGE SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 5.21 5.52 6.31 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 72.14 71.83 127.00 133.35127.00
5" 5-6 4.0 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 5.21 5.52 6.31 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 72.14 71.83 127.00 133.35127.00
5" 5-6 6.7 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 8.08 8.31 9.10 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 73.66 79.25 127.00 133.35127.00
5" 5-6 8.3 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 7.63 8.12 8.91 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 69.85 74.07 127.00 133.35127.00
5" 6-7 6.0 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 6.52 6.66 7.45 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 73.66 76.71 127.00 133.35127.00
5" 6-7 8.0 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 8.08 8.31 9.10 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 73.66 76.71 127.00 133.35127.00
5" 7-8 2.0 STAGE SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 8.11 8.31 9.10 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 75.95 71.12 127.00 133.35127.00
5" 7-8 2.6 STAGE HR NP SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 6.79 6.88 7.67 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 - - 127.00 133.35127.00
5" 7-8 2.6 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 7.55 7.79 8.58 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 69.85 78.74 127.00 133.35127.00
5" 7-8 3.7 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 7.41 7.93 8.72 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 79.50 79.25 127.00 133.35127.00
ROTOR ADAPTOR UNDERCUT Ø
ROTOR CATCH FLOAT SUB END
PISTON HOUSING UPSET END
THREAD PROTECTOR START
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
5" 7-8 3.8 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 6.48 6.71 7.50 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 75.44 74.93 127.00 133.35127.00
5" 7-8 4.5 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 7.55 7.79 8.58 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 69.85 78.49 127.00 133.35127.00
5" 7-8 5.0 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 6.68 6.99 7.78 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 69.85 77.24 127.00 133.35127.00
5" 8-9 6.0 STAGE HR SERIES 2 0.39 - 0.51 0.72 0.98 1.16 1.33 1.43 1.54 1.96 1.96 8.08 8.31 9.10 117.60 130.81 92.20 - 146.05128.52 128.52 143.76 128.52 143.76 128.52 49.02 90.93 71.40 69.85 77.24 127.00 133.35127.00
6 1/2" and 6 3/4" METRIC - SI (Lengths = m) (Diameters = mm)
6 ½ - 6 ¾" 4-5 7.0 STAGE HR
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 7.64 7.94 8.78 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 107.19 166.62 171.45166.62
SERIES 1
6 ½ - 6 ¾" 6-7 5.0 STAGE HR
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 7.42 7.57 8.41 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 109.73 166.62 171.45166.62
SERIES 1
6 ½ - 6 ¾" 7-8 2.0 STAGE HR
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 6.23 6.39 7.23 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 109.22 166.62 171.45166.62
SERIES 1
6 ½ - 6 ¾" 7-8 2.9 STAGE HR
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 7.91 8.08 8.92 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 109.22 166.62 171.45166.62
SERIES 1
6 ½ - 6 ¾" 7-8 3.0 STAGE
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 5.50 5.67 6.50 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 114.81 166.62 171.45166.62
SERIES 1
6 ½ - 6 ¾" 7-8 3.0 STAGE HR
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 5.50 5.67 6.50 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 114.81 166.62 171.45166.62
SERIES 1
6 ½ - 6 ¾" 7-8 3.0 STAGE HR
0.44 0.69 0.81 1.01 1.31 1.55 1.87 1.85 2.01 2.49 2.49 7.51 7.67 8.51 162.05 166.62 120.65 166.62 181.10166.62 172.97 181.10 172.97 181.10 172.97 70.10 123.44 101.60 101.60 116.08 166.62 171.45166.62
SLOW SERIES 1
338
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - METRIC (SI)
339 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
340
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - METRIC (SI)
341 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
342
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - METRIC (SI)
343 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
8" 7-8 3.0 STAGE HR SERIES 1 0.52 0.84 0.98 1.18 1.59 1.84 2.38 2.21 2.38 2.93 2.90 6.80 6.99 7.94 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 131.83 203.20 209.55203.20
8" 7-8 3.4 STAGE HR SERIES 1 0.52 0.84 0.98 1.18 1.59 1.84 2.38 2.21 2.38 2.93 2.90 10.34 10.55 11.50 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 134.80 203.20 209.55203.20
8" 7-8 4.0 STAGE SERIES 1 0.52 0.84 0.98 1.18 1.59 1.84 2.38 2.21 2.38 2.93 2.90 7.89 8.16 9.11 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 7-8 5.9 STAGE SERIES 1 0.52 0.84 0.98 1.18 1.59 1.84 2.38 2.21 2.38 2.93 2.90 10.12 10.55 11.50 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 7-8 4.0 STAGE HR SERIES 1 0.52 0.84 0.98 1.18 1.59 1.84 2.38 2.21 2.38 2.93 2.90 7.89 8.16 9.11 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 4-5 5.3 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 8.20 8.40 9.36 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.48 203.20 209.55203.20
8" 5-6 3.0 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 5.25 5.45 6.40 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 123.70 203.20 209.55203.20
8" 5-6 3.0 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 5.25 5.45 6.40 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 123.70 203.20 209.55203.20
8" 6-7 4.0 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 7.64 7.85 8.80 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 6-7 4.0 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 7.64 7.85 8.80 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 6-7 5.0 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 8.78 8.96 9.92 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 6-7 5.0 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 8.78 8.96 9.92 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 7-8 2.0 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 6.48 6.88 7.83 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 124.97 203.20 209.55203.20
8" 7-8 3.0 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 6.48 6.68 7.63 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 131.83 203.20 209.55203.20
8" 7-8 3.0 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 6.48 6.68 7.63 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 131.83 203.20 209.55203.20
8" 7-8 3.4 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 10.03 10.23 11.19 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 134.80 203.20 209.55203.20
8" 7-8 4.0 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 7.57 7.85 8.80 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
ROTOR ADAPTOR UNDERCUT Ø
ROTOR CATCH FLOAT SUB END
PISTON HOUSING UPSET END
THREAD PROTECTOR START
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
8" 7-8 4.0 STAGE HR SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 7.57 7.85 8.80 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 7-8 5.9 STAGE SERIES 2 0.41 0.70 0.82 1.02 1.28 1.53 2.07 1.90 2.07 2.61 2.58 9.81 10.23 11.19 196.85 203.20 158.75 203.20 222.25203.20 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 4-5 5.3 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 8.22 8.40 9.35 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.48 203.20 209.55203.20
8" 5-6 3.0 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 5.28 5.44 6.40 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 123.70 203.20 209.55203.20
8" 5-6 3.0 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 5.28 5.44 6.40 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 123.70 203.20 209.55203.20
8" 6-7 4.0 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 7.67 7.84 8.80 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 6-7 4.0 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 7.67 7.84 8.80 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 6-7 5.0 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 8.81 8.96 9.91 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 6-7 5.0 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 8.81 8.96 9.91 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 125.98 203.20 209.55203.20
8" 7-8 2.0 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 6.51 6.88 7.83 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 124.97 203.20 209.55203.20
8" 7-8 3.0 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 6.51 6.68 7.63 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 131.83 203.20 209.55203.20
8" 7-8 3.0 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 6.51 6.68 7.63 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 131.83 203.20 209.55203.20
8" 7-8 3.4 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 10.05 10.23 11.18 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 134.80 203.20 209.55203.20
8" 7-8 4.0 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 7.60 7.84 8.80 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 7-8 4.0 STAGE HR MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 7.60 7.84 8.80 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
8" 7-8 5.9 STAGE MUD LUBE 0.54 1.28 0.84 1.12 - 1.53 1.62 1.90 2.07 2.61 2.61 9.84 10.23 11.18 203.20 209.55 152.40 209.55 228.60 - 203.20 212.85 203.20 212.85 203.20 85.85 147.57 120.70 120.65 120.65 203.20 209.55203.20
344
MOTOR FISHING DIMENSIONS
MOTOR FISHING DIMENSIONS - IMPERIAL (USC)
345 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
ADAPTOR HOUSING Ø
ROTOR ADAPTOR END
ADJUSTING RING END
BEARING HOUSING Ø
FIXED HOUSING END
PISTON HOUSING Ø
BIT TO BEND (FIXED)
ADJUSTING RING Ø
FIXED HOUSING Ø
ROTOR MAJOR Ø
KICK HOUSING Ø
ROTOR HEAD Ø
DRIVE SHAFT Ø
END CAP END
MANDREL Ø
STATOR END
ROTOR END
END CAP Ø
TOP SUB Ø
BIT BOX Ø
STATOR Ø
A B C D E F1 G1 F2 G2 H I J K L M N O P Q R S1 T1 S2 T2 U V W X Y Z AA BB CC
346
MOTOR FISHING DIMENSIONS
SHOCK SUB FISHING DIMENSIONS - IMPERIAL (USC)
347 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
L
K
J
I
H
G
F
E
D
B
A
M N O P Q R S T U V W X Y Z AA BB CC DD EE
SPRING HOUSING INSIDE Ø
SPLINE HOUSING INSIDE Ø
MANDREL BEARING Ø
MANDREL SPLINE END
SPLINE HOUSING END
MANDREL SPRING Ø
TOP SUB UPSET END
SPRING HOUSING Ø
MANDREL SPLINE Ø
SPLINE HOUSING Ø
LOCK NUT Ø
SPRING Ø
SPACER Ø
BORE Ø
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA BB CC DD EE
348
SHOCK SUB FISHING DIMENSIONS
SHOCK SUB FISHING DIMENSIONS - METRIC (SI)
349 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
L
K
J
I
H
G
F
E
D
B
A
M N O P Q R S T U V W X Y Z AA BB CC DD EE
SPRING HOUSING INSIDE Ø
SPLINE HOUSING INSIDE Ø
MANDREL BEARING Ø
MANDREL SPLINE END
SPLINE HOUSING END
MANDREL SPRING Ø
TOP SUB UPSET END
SPRING HOUSING Ø
MANDREL SPLINE Ø
SPLINE HOUSING Ø
LOCK NUT Ø
SPRING Ø
SPACER Ø
BORE Ø
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA BB CC DD EE
350
SHOCK SUB FISHING DIMENSIONS
DYNO-JAR™ FISHING DIMENSIONS - IMPERIAL (USC)
351 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
S
R
Q
P
O
N
M
L
K
J
I
H
G
F
E
D
C
B
A
T U V W X Y Z AA BB CC DD EE FF GG HH II JJ KK LL MM
HYDRAULIC MANDREL HEAD END
COMPENSATION HOUSING Ø
LATCH MANDREL HEAD END
HYDRAULIC MANDREL Ø
MANDREL BEARING END
HYDRAULIC HOUSING Ø
LATCH MANDREL START
SPLINE HOUSING START
PISTON HOUSING Ø
SPLINE MANDREL Ø
LATCH MANDREL Ø
SPLINE HOUSING Ø
KNOCKER SUB END
LATCH HOUSING Ø
BOTTOM SUB END
WASH PIPE START
KNOCKER SUB Ø
WASH PIPE END
WASH PIPE Ø
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA BB CC DD EE FF GG HH II JJ KK LL MM
352
DYNO-JAR™ FISHING DIMENSIONS
DYNO-JAR™ FISHING DIMENSIONS - METRIC (SI)
353 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
S
R
Q
P
O
N
M
L
K
J
I
H
G
F
E
D
C
B
A
T U V W X Y Z AA BB CC DD EE FF GG HH II JJ KK LL MM
Jar
800
DMJ-
675
DMJ-
650
DMJ-
500
DMJ-
A
0.8
MANDREL HEAD END
B
SPLINE HOUSING START
C
MANDREL BEARING END
D
SPLINE HOUSING END
2.2
2.2
KNOCKER SUB START
F
KNOCKER SUB END
G
HYDRAULIC MANDREL HEAD END
2.58
2.59
2.59
2.44
I
3.4
3.4
COMPENSATION HOUSING END
3.38
3.19
J
4.1
3.8
6.4
6.4
71
65
65
57
95
SPLINE HOUSING Ø
207
173
167
127
METRIC - SI (Lengths = m) (Diameters = mm)
X
89
SPLINE MANDREL Ø
136
110
110
Y
KNOCKER HOUSING Ø
207
173
167
127
Z
93
KNOCKER SUB Ø
151
119
119
97
97
83
AA
HYDRAULIC MANDREL Ø
114
CC
COMPENSATION HOUSING Ø
207
173
167
127
HYDRAULIC HOUSING Ø
DD
207
173
167
127
EE
93
89
89
76
LATCH MANDREL Ø
114
LATCH HOUSING Ø
GG
207
173
167
127
HH
PISTON HOUSING Ø
207
173
167
127
II
89
89
76
WASH PIPE Ø
114
JJ
354
API CONNECTION INTERCHANGEABILITY
355 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
NC Internal Flush Full Hole Extra Hole Slim Hole Wide Open
- - - 3-1/2 XH 4 SH -
NC40 - 4 FH - - -
NC46 4 IF - 4-1/2 XH - 4 WO
NC50 4-1/2 IF - 5 XH - -
Motor Size Connection Float Valve Size
2-7/8 in (73 mm) SERIES 2 2-3/8 PAC 1F-2R
3-1/8 in (79 mm) SERIES 1 2-3/8 PAC 1F-2R
3-3/4 in (95 mm) SERIES 1 2-3/8 IF (NC26) 1F-2R
3-3/4 in (95 mm) SERIES 1 optional 2-7/8 REG 1F-2R
5 in (127 mm) SERIES 2 3-1/2 IF (NC38) 2F-3R
6-1/2 in (165 mm) SERIES 1 4-1/2 IF (NC50) 4R
6-1/2 in (165 mm) SERIES 1 optional 4-1/2 XH (NC46) 4R
6-1/2 in (165 mm) SERIES 3 4-1/2 IF (NC50) 4R
6-1/2 in (165 mm) SERIES 3 optional 4-1/2 XH (NC46) 4R
6-3/4 in (171 mm) SERIES 1 4-1/2 IF (NC50) 4R
6-3/4 in (171 mm) SERIES 1 optional 4-1/2 XH (NC46) 4R
6-3/4 in (171 mm) SERIES 2 SHORT 4-1/2 IF (NC50) 4R
6-3/4 in (171 mm) SERIES 2 SHORT optional 5-1/2 REG 5R
6-3/4 in (171 mm) SERIES 3 4-1/2 IF (NC50) 4R
6-3/4 in (171 mm) SERIES 3 optional 4-1/2 XH (NC46) 4R
7 in (178 mm) SERIES 3 4-1/2 IF (NC50) 4R
7 in (178 mm) SERIES 3 optional 4-1/2 XH (NC46) 4R
8 in (203 mm) SERIES 1 6-5/8 REG 5F-6R
8 in (203 mm) SERIES 2 6-5/8 REG 5F-6R
8 in (203 mm) MUD LUBE 6-5/8 REG 5F-6R
9-5/8 in (244 mm) SERIES 1 6-5/8 REG 5F-6R
9-5/8 in (244 mm) SERIES 1 optional 7-5/8 REG 5F-6R
11-1/4 in (286 mm) SERIES 1 6-5/8 REG 5F-6R
11-1/4 in (286 mm) SERIES 1 optional 7-5/8 REG 5F-6R
356
FLOAT VALVE SIZES
ADJUSTABLE SETTING INSTRUCTIONS
357 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
1 2 3 4 5 6
PULL
SPIN
BREAKOUT MAKEUP
ROTATE ROTATE
2.12 5 Slide Kick Ring back to engage Kick Housing. Chain tong snug. 6-3/4” S1/S3 25,000 33,900
2.97
3.00
358
ADJUSTABLE PROCEDURE
CONVERSION TABLE
359 7501 42 STREET LEDUC, ALBERTA T9E 0R8 T: 780.986.3070 F:780.986.3536 www.dynomaxdrillingtools.com sales@dynomaxdrillingtools.com
sales@DYNOMAXDrillingTools.com
DYNOMAX Drilling Tools Inc. DYNOMAX Drilling Tools USA Inc. DYNOMAX Drilling Tools Inc.
7501 42 Street 2830 Farrell Rd. 309 Sawyer Road
Leduc, Alberta T9E 0R8 Houston, Texas 77073 Estevan, Saskatchewan S4A 2H8
Canada USA Canada
Tel: 780-986-3070 Tel: 832-486-9575 Tel: 306-634-4949
Fax: 780-986-3536 Fax: 832-486-9975 Fax: 306-634-4959