Professional Documents
Culture Documents
Service mannal
Room airconditioner
NOTE:
1
Table of Contents
1、Summary ………………………………………………………………………………………………………………3
3、Installation……………………………………………………………………………………………………………..4
5、Operation principle………………………………………………………………………………………………….8
6、Parameter………………………………………………………………………………………………………………9
7、Wiring diagrams……………………………………………………………………………………………………...13
10、Troubleshooting………………………………………………………………………………....30
2
1. Summary
1.1 indoor unit
3
2、Model explaining
c
Improve an ordinal number
Separately the body pit code inside the indoor machine(or whole
type)
3. Attention of installation
3.1 Safety Precaution
■To prevent injury to the user or other people and property damage, the following instructions must be followed.
■Incorrect operation due to ignoring instruction will cause harm or damage.
■Before service unit, be sure to read this service manual at first.
3.2 Warning
﹥Installation
■Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.
4
There is risk of fire or electric shock.
■For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized service center.
Do not disassemble or repair the product, there is risk of fire or electric shock.
■Always ground the product.
There is risk of fire or electric shock.
■Install the panel and the cover of control box securely.
There is risk of fire of electric shock.
■Always install a dedicated circuit and breaker.
Improper wiring or installation may cause fore or electric shock.
■Use the correctly rated breaker of fuse.
There is risk of fire or electric shock.
■Do not modify or extend the power cable.
There is risk of fire or electric shock.
■Do not install, remove, or reinstall the unit by yourself (customer).
There is risk of fire, electric shock, explosion, or injury.
■Be caution when unpacking and installing the product.
Sharp edges could cause injury, be especially careful of the case edges and the fins on the condenser and evaporator.
■ For installation, always contact the dealer or an Authorized service center.
There is risk of fire, electric shock, explosion, or injury.
■Do not install the product on a defective installation stand.
It may cause injury, accident, or damage to the product.
■Be sure the installation area does not deteriorate with age.
If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury.
■Do not let the air conditioner run for a long time when the humidity is very high and a door or a windows is left open.
Moisture may condense and wet or damage furniture.
■Take care to ensure that power cable could not be pulled out or damaged during operation.
There is risk of fire or electric shock.
■ Do not place anything on the power cable.
There is risk of fire or electric shock.
■Do not plug or unplug the power supply plug during operation.
There is risk of fire or electric shock.
■Do not touch (operation) the product with wet hands.
There is risk of fire or electric shock.
■Do not place a heater or other appliance near the power cable.
There is risk of fire and electric shock.
■Do not allow water to run into electric parts.
It may cause fire, failure of the product, or electric shock.
■Do not store or use flammable gas or combustible near the product.
There is risk of fire or failure of product.
■ Do not use the product in a tightly closed space for a long time.
Oxygen deficiency could occur.
■When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.
Do not use the telephone or turn switches on or off. There is risk of explosion or fire.
■If strange sounds, or small or smoke comes from product. Turn the breaker off or disconnect the power supply cable.
There is risk of electric shock or fire.
■Stop operation and close the window in storm or hurricane. If possible, remove the product from the window before the hurricane
arrives.
There is risk of property damage, failure of product, or electric shock.
5
■Do not open the inlet grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so equipped.)
There is risk of physical injury, electric shock, or product failure.
■When the product is soaked (flooded or submerged), contact an Authorized service center.
There is risk of fire or electric shock.
■Be caution that water could not enter the product.
There is risk of fire, electric shock, or product damage.
■Ventilate the product from time to time when operating it together with a stove, etc.
There is risk of fire or electric shock.
■Turn the main power off when cleaning or maintaining the product.
There is risk of electric shock.
■When the product is not be used for a long time, disconnect the power supply plug or turn off the breaker.
There is risk of product damage or failure, or unintended operation.
■Take care to ensure that nobody could step on or fall onto the outdoor unit.
This could result in personal injury and product damage.
﹥CAUTION
■Always check for gas (refrigerant) leakage after installation or repair of product.
Low refrigerant levels may cause failure of product.
■Install the drain hose to ensure that water is drained away properly.
A bad connection may cause water leakage.
■Keep level even when installing the product.
To avoid vibration of water leakage.
■Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods.
It may cause a problem for your neighbors.
■Use two or more people to lift and transport the product.
Avoid personal injury.
■Do not install the product where it will be exposed to sea wind (salt spray) directly.
It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could cause product malfunction or
inefficient operation.
﹥Operational
■Do not expose the skin directly to cool air for long periods of time. (Do not sit in the draft).
This could harm to your health.
■ Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a consumer air conditioner, not a
precision refrigerant system.
There is risk of damage or loss of property.
■ Do not block the inlet or outlet of air flow.
It may cause product failure.
■Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.
There is risk of fire, electric shock, or damage to the plastic parts of the product.
■ Do not touch the metal parts of the product when removing the air filter. They are very sharp.
There is risk of personal injury.
■ Do not step on pr put anything on the product. (outdoor units)
There is risk of personal injury and failure of product.
■Always insert the filter securely. Clean the filter every two weeks or more often if necessary.
A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage.
■Do not insert hands or other object through air inlet or outlet while the product is operated.
There are sharp and moving parts that could cause personal injury.
6
■ Do not drink the water drained from the product.
It is not sanitary could cause serious health issues.
■Use a firm stool or ladder when cleaning or maintaining the product.
Be careful and avoid personal injury.
■Replace the all batteries in the remote control with new ones of the same type. Do not mix old and mew batteries or different types of
batteries.
There is risk of fire or explosion.
■ Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire.
They may burn of explode.
■ If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. Do not use the remote of the batteries
have leaked.
The chemical in batteries could cause burns or other health hazards.
Grade
Unit 7K 9K 12K 18K 24K 28K
mm2 1.0 1.0 1.5 2.5 2.5 2.5
7
Lo Hi
Caution:Capacity is base on standard length and maximum allowance length is base of reliability.Oil
trap should be install per 5-7 meters.
4、Indoor unit and outdoor unit explosion diagram and spare parts list(see explosion diagram file)
8
6. Parameter
Table 6-1
Model KFR-25GW/AGX1c KFR-35GW/AGX1c KFR-51GW/BGX1c KFR-70GW/X1c
Power supply Ph-V-Hz 220-240/50 220-240/50 220-240/50 220-240/50
Capacity W 2600/2780 3433/3590 5100 7000
Input W 928/865 1183/1120 1590 2300
Cooling
Rated current A 4.1/4.0 5.2/5.1 6.8 10.3
EER w/w. 2.8/3.2 2.90/3.2 3.21 3.043478261
Capacity w 2700/2780 3414/3680 5200 7500
Input W 812/770 1076/1020 1600 2330
Heating
Rated current A 3.6/3.5 4.8/4.7 6.9 10.4
COP w/w 3.30/3.61 3.17/3.6 3.25 3.21888412
Max. input consumption W 1250 2170 2300 3600
Max. current A 7 10.6 12.3 19.5
Model PA108X1C-4DZDE PA140X2C-4FT PA200X2CS-4KU1 PA270X3CS-4MU2
Type ROTAING ROTAING ROTAING ROTAING
Brand TSHIBA TSHIBA TSHIBA TSHIBA
Capacity W 2570 3365 4890 6650
Input W 885±5℅ 1160±5℅ 1715 2270
Start electric current A 21.7±10℅ 31.83 10.32
Rated current(RLA)/Locked
Compressor A 4.15±5℅ 5.4±5℅ 7.45
rotor Amp(LRA)
B160-135-241E/MR
UP3-RE0596-T56/ UP3QE0391-T39/
Thermal protector A13430-9087/ Outside sets
Outside sets Outside sets
Outside sets
Capacitor uF 25 35 45 50/400
ESTER OIL ESTER OIL VG74.
Refrigerant oil ml
VG74/350 750mi
Model YDK-16-4 YDK-16-4 YDK-16-4 YDK-38-4
Brand W 35 35 45W 82
Fan motor
Capacitor uF 1.2 1.2 1.2μF 3.5
Indoor unit
9
Packing (W*H*D) mm 825×320×550 920*335*595 920*335*595 990*410*775
Net/Gross weight Kg 30/31 33/36 40/42 58/62
Refrigerant type g R410A/600 R410A/920 R410A/1350 R410A/2100
Design pressure MPa 3.8/1.2 3.8/1.2 4.0-1.2 4.0-1.2
connecting Liquid pipe/ gas pipe 6.35/ 9.52 φ9.52+
mm 6.35/9.52 /3500 6.35/12.7 /4000
pipe/cable dia./length /3500 φ16×5000
Electric PCB model ZKFR-32GW/A 38-F ZKFR-32GW/A 38-F ZKFR-51GW/A 38-F ZGHT-65-3CM
fittings Fuse model/fuse current A 50CT/3.15 50CT/3.15 50CT/3.15 50CT/3.15
Remote controller type ZH/JG-01 ZH/JG-01 ZH/JG-01 ZH-LW-01
function horizontal(auto/manual) Hand Moving Hand Moving Hand Moving Hand Moving
swing
vertical(auto/manual) Automatic Automatic Automatic Automatic
Table 6-2
CS-25H3A-V**AY CS-35H3A-M**A CS-51H3A-P**AH CS-61H3A-P**A
Model
1 H4 4A E2
Power supply Ph-V-Hz 220-240/50 220-240/50 220-240/50 220-240/50
Capacity W 2780 3600 5100 6200
Input W 860 1120 1590 2040
Cooling
Rated current A 3.9 5.1 6.8 9.2
EER w/w. 3.23 3.21 3.21 3.04
Capacity w 2780 3750 5400 6600
Input W 770 1040 1600 1940
Heating
Rated current A 3.4 4.7 6.9 8.7
COP w/w 3.61 3.61 3.38 3.40
Max. input consumption W 1600 1850 2400 2700
Max. current A 8 9.9 12.5 14.3
PA240X2CS-4KU
Model PA108X1C-4DZDE PA140X2c-4FT PA200X2C-4KU1
1
Type ROTAING ROTAING ROTAING ROTAING
Brand TSHIBA TSHIBA TSHIBA TSHIBA
Capacity W 2570 3365 4840 5800
Input W 885 1160 1655 1985
Compressor
Start electric current A
Rated current(RLA)/Locked
A 4.02 5.27 7.52 9.02
rotor Amp(LRA)
Thermal protector Outside sets Outside sets Outside sets Outside sets
Capacitor uF 25/370 35/370 45/370 50/370
Refrigerant oil ml
Model YDK-14-4 YDK-16-4 3 YDK-23-4 A6 YDK-27-4 A6
Brand W 40 33 47 56
Fan motor
Indoor unit
10
Packing (W*H*D) mm 833*330*270 860*350*265 990*377*300 990*377*300
Net/Gross weight Kg 9/11 12/14 14/17 14/17
Model YDK-30-6 YDK-35-6A H YDK-38-6B YDK-40-6A 1
Input W 85 65 80 106
Fan motor
Capacitor uF 2 2 2.5 3
Speed r/min 890 900 920 870
Fan motor diameter×height mm φ384×136 φ401×115 Φ401×115 Φ415*115
Outdoor uni
Table 6-23
Model KFR-70GW/X1c
11
Model YDK-38-4
Brand W 82
Fan motor
Capacitor uF 3.5
Indoor unit
12
CS-21H3A-C38AY1A(EER≥ CS-21H3A-M**AY1(EER≥
Model
3.2) 2.9)
Rated volt and frequency Ph-V-Hz 220-240V/50Hz 220-240/50
Cooling capacity (actual/label) W 2100 2200
Cooling power input
W 650 685
(actual/label)
Cooling
Heating current input
A 2.9 3.3
(actual/label)
EER (actual/label) W/W 3.23 3.21
Heating capacity (actual/label) W 2100 2300
Heating power input
W 620 635
(actual/label)
Heating
Heating current input
A 2.8 3.0
(actual/label)
COP (actual/label) W/W 3.39 3.62
Max. input consumption W 900 1050
Max. current A 4.8 5.4
Model 5RS080EAB21 PA89X1C-4DZDE
Type (Rotary、piston 、scroll) Rotary Rotary
Brand PANASONIC TOSHIBA
Capacity W 1840/1870 2075/2100
Power input W 665/680 715/735
Starting
current---(LRA)locked-rotor
A 11.3/12.4 15
current
Compressor
LRA
Running current
A 3.05/2.90 3.3/3.15
RLA
protector type (internal
external B135-135-241E/external
/external)
capacity uF-V 20/370 25/370
Refrigeration lubricating oils,oil ESTER OIL VG74
ml FV50S \370
charge 350ml
Model YDK-16-4 YDK-16-4G
Power input W 40 30
Fan motor capacity uF 1.2 1.2
Indoor Fan Speed RPM
r/min 1150/950/850 1290
(High/Med/Low)
Indoor fan dia.*length mm φ97×633 φ98x622
Rows*Tubes*Circuits 2*12*2 2*15*2
Tube pitch* row pitch*Fin
mm 17.6*12.3*1.4 21*12.7*1.4
spacing
indoor unit
Tube outside dia.and typ mm φ7×0.32internal threaded pipe φ7/internal threaded pipe
Tube outside dia.and typ mm 7/internal threaded pipe φ7/internal threaded pipe
Coil size :length x height x 620*462*13.37
mm 648*462*12.7
width 641*462*13.37
Outdoor Noise Level dB (High/Low)
dB(A) 49 51
(actual/label)
Dimension size (L*W*H) mm 700*225*500 700*225*500
KFR-21GW/GX1c(EER≥
Model KFR-21GW/GX1DC(EER≥3.2)
3.2)
Rated volt and frequency Ph-V-Hz 220-240V/50Hz 220-240V/50Hz
Cooling capacity (actual/label) W 2100 2100
Cooling power input
W 650 650
(actual/label)
Cooling
Heating current input
A 2.8 2.8
(actual/label)
EER (actual/label) W/W 3.23 3.23
Heating capacity (actual/label) W 2200 2200
Heating power input
W 660 660
(actual/label)
Heating
Heating current input
A 2.9 2.9
(actual/label)
COP (actual/label) W/W 3.33 3.33
Max. input consumption W 900 900
Max. current A 4.8 4.8
Model PA82X1C-4DZDE PA82X1C-4DZDE
Type (Rotary、piston 、scroll) Rotary Rotary
Brand TOSHIBA TOSHIBA
Capacity W 1920/1950 1920/1950
Power input W 660/680 660/680
Starting
current---(LRA)locked-rotor
A 15 15
current
Compressor
LRA
Running current
A 3.04/2.85 3.04/2.85
RLA
protector type (internal
external 外置
/external)
capacity uF-V 25/370 25/370
Refrigeration lubricating oils,oil
ml ESTER OIL VG74 \750 ESTER OIL VG74 \750
charge
indoor unit Model YDK-16-4 YDK-16-4
Power input W 35 35
Fan motor capacity uF 1.2 1.2
Indoor Fan Speed RPM
r/min 1250/1050 /850 1250/1050 /850
(High/Med/Low)
Indoor fan dia.*length mm φ93×633 φ93×633
Rows*Tubes*Circuits 2X12X2 2*12*2
Tube pitch* row pitch*Fin
mm 17.6X12.3X1.4 17.6*12.3*1.4
spacing
φ7×0.32internal threaded
Tube outside dia.and typ mm φ7×0.32internal threaded pipe
pipe
557*82*21.8
Coil length x height x width mm 647*197*25.2
579*169*21.8
Indoor Air Circulation (High/Med/Low)
m3/h 550/480/400/(500) 400
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 42.3/36.5/30.9 29~38
(actual/label)
Dimension (L*W*H) mm 790*270*180 745*250*195
Tube outside dia.and typ mm 7/internal threaded pipe φ7internal threaded pipe
580*167*25.4 580*167*25.4
Coil length x height x width mm
558*82*25.4 558*82*25.4
Indoor Air Circulation (High/Med/Low)
m3/h 450/425 500
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 32-39/32.8-38.8 29-39
(actual/label)
Dimension (L*W*H) mm 746*245*196 746*245*196
CS-25H3A-V**AY1(EER≥ CS-25H3A-V**AY1(EER≥
Model
2.9) 2.9)
Rated volt and frequency Ph-V-Hz 220-240/50 220-240/50
Cooling capacity (actual/label) W 2780 2780
Cooling power input
W 860 860
(actual/label)
Cooling
Heating current input
A 3.9 3.9
(actual/label)
EER (actual/label) W/W 3.23 3.23
Heating capacity (actual/label) W 2780 2780
Heating power input
W 770 770
(actual/label)
Heating
Heating current input
A 3.4 3.4
(actual/label)
COP (actual/label) W/W 3.61 3.61
Max. input consumption W 1600 1600
Max. current A 8 8
Model KN108VGMMC 5PS108EAA22
Type (Rotary、piston 、scroll) Rotary Rotary
Brand MITSUBISHI PANASONIC
Capacity W 2520 2515/2535
Power input W 795 880/900
Starting
current---(LRA)locked-rotor
A 20 18/19.6
current
Compressor
LRA
Running current
A 3.61 4.05/3.8
RLA
protector type (internal KA-122-LPD021A
internal
/external) external
capacity uF-V 25μF/450V/50/60Hz/φ50 30/370
Refrigeration lubricating oils,oil
ml FV50S 350ml
charge
indoor unit Model YDK-14-4 YDK-14-4
Power input W 40 40
Fan motor capacity uF 1.2 1.2
Indoor Fan Speed RPM
r/min 1320 1320
(High/Med/Low)
Indoor fan dia.*length mm φ97*583 φ97*583
Rows*Tubes*Circuits 2*12*2 2*12*2
Tube pitch* row pitch*Fin
mm 21*12.7*1.6 21*12.7*1.6
spacing
Tube outside dia.and typ mm φ7internal threaded pipe φ7internal threaded pipe
580*167*25.4 580*167*25.4
Coil length x height x width mm
558*82*25.4 558*82*25.4
Indoor Air Circulation (High/Med/Low)
m3/h 500 500
(actual/label)
580*167*25.4
Coil length x height x width mm 615*315*25.4
558*82*25.4
Indoor Air Circulation (High/Med/Low)
m3/h 400 500
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 29-39 29-39
(actual/label)
Dimension (L*W*H) mm 800*280*190 746*245*196
Tube outside dia.and typ mm φ7internal threaded pipe φ7internal threaded pipe
579*168*25.4
Coil length x height x width mm 647X197
557*84*25.4
Indoor Air Circulation (High/Med/Low)
m3/h 550/480/400/(500) 450
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 42.3/36.5/30.9 29-40
(actual/label)
Dimension (L*W*H) mm 790*270*180 746*245*196
Tube outside dia.and typ mm φ7/internal threaded pipe φ9.52internal threaded pipe
579*168*25.4 579*168*25.4
Coil length x height x width mm
557*84*25.4 557*84*25.4
Indoor Air Circulation (High/Med/Low)
m3/h 450 450
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 29-40 29-40
(actual/label)
Dimension (L*W*H) mm 746*245*196 746*245*196
Tube outside dia.and typ mm φ9.52internal threaded pipe φ9.52internal threaded pipe
Coil size :length x height x
mm 783*500*22 783*500*22
width
Outdoor Noise Level dB (High/Low)
dB(A) 54 54
(actual/label)
Dimension size (L*W*H) mm 795*255*540 795*255*540
KFR-32GW/GX1c(EER≥
Model KFR-32GW/GX1DC(EER≥3.2)
3.2)
Rated volt and frequency Ph-V-Hz 220-240V/50Hz 220-240V/50Hz
Cooling capacity (actual/label) W 3200 3200
Cooling power input
W 950 950
(actual/label)
Cooling
Heating current input
A 4.1 4.1
(actual/label)
EER (actual/label) W/W 3.37 3.37
Heating capacity (actual/label) W 3200 3200
Heating power input
W 880 880
(actual/label)
Heating
Heating current input
A 3.8 3.8
(actual/label)
COP (actual/label) W/W 3.64 3.64
Max. input consumption W 1300 1300
Max. current A 7 7
Compressor Model PA118X1C-4FZ PA118X1C-4FZ
Type (Rotary、piston 、scroll) Rotary Rotary
Brand TOSHIBA TOSHIBA
Capacity W 2800/2815 2800/2815
Power input W 965/980 965/980
Starting
current---(LRA)locked-rotor
A 21.7/23.7 21.7/23.7
current
LRA
Running current
A 4.50/4.30 4.50/4.30
RLA
protector type (internal
internal internal
/external)
capacity uF-V 25/370 25/370
Refrigeration lubricating oils,oil
ml ESTER OIL VG74 \350 ESTER OIL VG74 \350
charge
indoor unit Model YDK-16-4 YDK-16-4
Power input W 35 35
Fan motor capacity uF 1.2 1.2
Indoor Fan Speed RPM
r/min 1250/1050 /850 1250/1050 /850
(High/Med/Low)
Indoor fan dia.*length mm 97X 633 97*633
Rows*Tubes*Circuits 2*16*3 2*16*3
Tube pitch* row pitch*Fin
mm 17.6X12.7X1.56 17.6*12.7*1.56
spacing
φ7×0.25+0.18/internal φ7×0.25+0.18/internal threaded
Tube outside dia.and typ mm
threaded pipe pipe
CS-35H3A-M**AH4(EER≥
Model CS-35H3A-M**AH4A
2.9)
Rated volt and frequency Ph-V-Hz 220-240/50 220-240/50
Cooling capacity (actual/label) W 3600 3500
Cooling power input
W 1120 1125
(actual/label)
Cooling
Heating current input
A 5.1 5
(actual/label)
EER (actual/label) W/W 3.21 3.11
Heating capacity (actual/label) W 3750 3600
Heating power input
W 1040 1100
(actual/label)
Heating
Heating current input
A 4.7 4.9
(actual/label)
COP (actual/label) W/W 3.61 3.27
Max. input consumption W 1850 1880
Max. current A 9.9 10
Model 5KS140EBA21 PA140X2c-4FT
Type (Rotary、piston 、scroll) Rotary Rotary
Brand PANASONIC TOSHIBA
Capacity W 3360/3390 3365
Power input W 1180/1200 1160
Starting
current---(LRA)locked-rotor
A 25.3/27.6
current
Compressor
LRA
Running current
A 5.4/5.1 5.27
RLA
protector type (internal B210-155-141C
internal
/external) external
capacity uF-V 35/400 35/370
Refrigeration lubricating oils,oil
ml FV50S 430ml
charge
indoor unit Model YDK-16-4 3 YDK-16-4 3
Power input W 33 33
Fan motor capacity uF 1 1
Indoor Fan Speed RPM
r/min 1320 1320
(High/Med/Low)
Indoor fan dia.*length mm φ100x622 φ100x622
Rows*Tubes*Circuits 2*15*2 2*15*2
Tube pitch* row pitch*Fin
mm 21*12.7*1.4 21*12.7*1.4
spacing
Tube outside dia.and typ mm φ7internal threaded pipe φ7internal threaded pipe
Liquid side/ Gas side/Length mm 6.35/ 9.52 /3500 6.35/ 9.52 /3500
Refrigerant piping
Max. refrigerant pipe length
m 15/5 15/5
/Max. difference in level
KFR-35GW/AGX1C(EER≥
Model KFR-35GW/AGX1DC(EER≥2.9)
2.9)
Rated volt and frequency Ph-V-Hz 230/50 220-240V/50Hz
Cooling capacity (actual/label) W 3433/3590 3433/3590
Cooling power input
W 1183/1120 1183/1120
(actual/label)
Cooling
Heating current input
A 5.2/5.1 5.2/5.1
(actual/label)
EER (actual/label) W/W 2.90/3.21 2.90/3.21
Heating capacity (actual/label) W 3414/3680 3414/3680
Heating power input
W 1076/1020 1076/1020
(actual/label)
Heating
Heating current input
A 4.8/4.7 4.8/4.7
(actual/label)
COP (actual/label) W/W 3.17/3.61 3.17/3.61
Max. input consumption W 2170 2170
Max. current A 10.6 10.6
Compressor Model 5KS140EBA21 PA140X2C-4FT
Type (Rotary、piston 、scroll) Rotary Rotary
Brand PANASONIC TOSHIBA
Capacity W 3360/3390±5% 3365
Power input W 1180/1200±5% 1160±5℅
Starting
current---(LRA)locked-rotor
A 29.7/28.1
current
LRA
Running current
A 5.4/5.1 5.4±5℅
RLA
protector type (internal
7100858(B210-155-141C UP3-RE0596-T56/internal
/external)
capacity uF-V 35μF±5% 35
Refrigeration lubricating oils,oil
ml
charge
indoor unit Model YDK-16-4 YDK-16-4
Power input W 35 35
Fan motor capacity uF 1.2 1.2
Indoor Fan Speed RPM
r/min 1250/1050 /850 1250/1050 /850
(High/Med/Low)
Indoor fan dia.*length mm 97X 633 φ97×633
Rows*Tubes*Circuits 2X16X3 2*16*3
Tube pitch* row pitch*Fin
mm 17.6X12.7X1.56 17.6*12.7*1.56
spacing
φ7×0.25+0.18/internal
Tube outside dia.and typ mm φ7×0.25+0.18/internal threaded pipe
threaded pipe
Liquid side/ Gas side/Length mm 6.35/ 9.52 /3500 6.35/ 9.52 /3500
Refrigerant piping
Max. refrigerant pipe length
m 15/5 15/5
/Max. difference in level
CS-51C3A-P**AH4(EER≥
Model CS-51H3A-P**AH4
2.75)
Rated volt and frequency Ph-V-Hz 220-240/50 220-240/50
Cooling capacity (actual/label) W 5400/5025 5100
Cooling power input
W 1685/1743 1800
(actual/label)
Cooling
Heating current input
A 7.3/7.5 8.1
(actual/label)
EER (actual/label) W/W 3.21/2.88 2.83
Heating capacity (actual/label) W 5400
Heating power input
W 1700
(actual/label)
Heating
Heating current input
A 7.6
(actual/label)
COP (actual/label) W/W 3.18
Max. input consumption W 2200 2400
Max. current A 11.5 12.5
Model PA200X2C-4KU1 PA200X2C-4KU1
Type (Rotary、piston 、scroll) Rotary Rotary
Brand TOSHIBA TOSHIBA
Capacity W 4840 4840
Power input W 1655 1655
Starting
current---(LRA)locked-rotor
A
Compressor current
LRA
Running current
A 7.52 7.52
RLA
protector type (internal
internal internal
/external)
capacity uF-V 45/370 45/370
Tube outside dia.and typ mm φ7internal threaded pipe φ9.52internal threaded pipe
Coil size :length x height x 747*504*13.37 727*500*21.65
mm
width 768*504*13.37 761*500*21.65
Outdoor Noise Level dB (High/Low)
dB(A) 54 54
(actual/label)
Dimension size (L*W*H) mm 795*255*540 795*255*540
CS-51H3A-P**AH4A(EER≥
Model CS-51H3A-N**AE2
2.75)
Rated volt and frequency Ph-V-Hz 220-240/50 220-240V/50Hz
Cooling capacity (actual/label) W 5100 5100
Cooling power input
W 1590 1590
(actual/label)
Cooling
Heating current input
A 6.8 6.8
(actual/label)
EER (actual/label) W/W 3.21 3.21
Heating capacity (actual/label) W 5400 5600
Heating power input
W 1600 1550
(actual/label)
Heating
Heating current input
A 6.9 6.7
(actual/label)
COP (actual/label) W/W 3.38 3.61
Max. input consumption W 2400 2300
Max. current A 12.5 12.3
Model PA200X2C-4KU1 PA200X2CS-4KU1
Type (Rotary、piston 、scroll) Rotary Rotary
Brand TOSHIBA TOSHIBA
Capacity W 4840 4890
Power input W 1655 1715
Starting
current---(LRA)locked-rotor
A 31.83
current
Compressor
LRA
Running current
A 7.52 7.45
RLA
protector type (internal
internal UP3QE0391-T39internal
/external)
capacity uF-V 45/370 45
Refrigeration lubricating oils,oil
ml ESTER OIL VG74. 750mi
charge
indoor unit Model YDK-23-4 A6 YDK-26-4 A6
Power input W 47 56
capacity uF 1.8 1.8
Fan motor
1250±20rpm
Indoor Fan Speed RPM
r/min 1150±30rpm 1300/1200/1080
(High/Med/Low)
1050±40rpm
Indoor fan dia.*length mm φ98*715 φ101.5χ762
Rows*Tubes*Circuits 2*17*3 2*18
Tube pitch* row pitch*Fin
mm 21*12.7*1.6 20.4*12.7*1.45
spacing
Tube outside dia.and typ mm φ7internal threaded pipe φ7internal threaded pipe
766*252*25.4
Coil length x height x width mm 705*357*25.4
747*126*25.4
Indoor Air Circulation (High/Med/Low)
m3/h 800 900
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 37-47 43-47
(actual/label)
Dimension (L*W*H) mm 900*292*215 1000×320×200
1190×380×300(有附件)
Packing (L*W*H) mm 990*377*300
1085×380×300(无附件)
Net/Gross weight Kg 14/17 15/17
Model YDK-38-6B YDK-40-6A 1
Power input W 80 105
Fan motor capacity uF 2.5 3
Outdoor Fan Speed RPM
r/min 920 870
(High/Med/Low)
Outdoor
dia.*length mm Φ401×115 Φ415
fan
Rows*Tubes*Circuits 2*20* 2*24
Tube pitch* row pitch*Fin
Outdoor unit mm 25*21.65*1.7 22*19.05*1.6
spacing
condensor
Tube outside dia.and typ mm φ9.52internal threaded pipe φ8internal threaded pipe
CS-61H3A-P**AE2(EER≥
Model KFR-51GW/BGX1c(EER≥2.75)
2.75)
Rated volt and frequency Ph-V-Hz 220-240V/50Hz 220-240/50
Cooling capacity (actual/label) W 5100 5975/6200
Cooling power input
W 1590 2112/2040
(actual/label)
Cooling
Heating current input
A 6.8 9.6/9.2
(actual/label)
EER (actual/label) W/W 3.21 2.83/3.04
Heating capacity (actual/label) W 5200 6388/6600
Heating power input
W 1600 2114/1940
(actual/label)
Heating
Heating current input
A 6.9 9.6/8.7
(actual/label)
COP (actual/label) W/W 3.25 3.02/3.40
Max. input consumption W 2300 2700
Max. current A 12.3 14.3
Model PA200X2CS-4KU1 PA240X2CS-4KU1
Type (Rotary、piston 、scroll) Rotary Rotary
Brand TOSHIBA TOSHIBA
Capacity W 4890 5800
Power input W 1715 1985
Starting
current---(LRA)locked-rotor
A 31.83 36.8
current
Compressor
LRA
Running current
A 7.45 9.3
RLA
protector type (internal
UP3QE0391-T39internal internal
/external)
capacity uF-V 45 50/370
Refrigeration lubricating oils,oil
ml ESTER OIL VG74. 750mi ESTER OIL VG74 750ml
charge
indoor unit Model (YDK-16-4)220-240V/50Hz YDK-27-4 A6
Power input W 45W 56
capacity uF 1.2μF 1.8
Fan motor
Hi:1250±10rpm Hi::1300±20rpm
Indoor Fan Speed RPM
r/min Med:1050±10rpm Med::1200±30rpm
(High/Med/Low)
low:850±10rpm low::1100±40rpm
Indoor fan dia.*length mm φ97×772 φ102χ710
Rows*Tubes*Circuits 2*16*4 2*20*5
Tube pitch* row pitch*Fin
mm 17.6X13X1.56 21*12.7*1.6
spacing
Tube outside dia.and typ mm φ7/internal threaded pipe φ7internal threaded pipe
705*375*25.4
Coil length x height x width mm 787*280*25.4
705*126*12.7
Indoor Air Circulation (High/Med/Low)
m3/h 720 859/900
(actual/label)
机型 CS-70H3A-W**ASA(EER≥
CS-70H3A-T**AS
Model 2.75)
Rated volt and frequency Ph-V-Hz 220-240V/50Hz 220-240/50
Cooling capacity (actual/label) W 7000 7200
Cooling power input
W 2300 2250
(actual/label)
Cooling
Heating current input
A 11 10.1
(actual/label)
EER (actual/label) W/W 3.04 3.20
Heating capacity (actual/label) W 7100 7400
Heating power input
W 2400 2160
(actual/label)
Heating
Heating current input
A 11.5 9.7
(actual/label)
COP (actual/label) W/W 2.96 3.43
Max. input consumption W 3600 3700
Max. current A 19.6 18
Model PA270X3CS-4MU2 PA270X3CS-4MU2
Type (Rotary、piston 、scroll) Rotary Rotary
Brand TOSHIBA TOSHIBA
Capacity W 7180/7210 6650
Power input W 2430/2540 2270
Starting
current---(LRA)locked-rotor
A 61/63
current
Compressor
LRA
Running current
A 11.04/11.54 10.32
RLA
protector type (internal
internal internal
/external)
capacity uF-V 50-400 50/400
Refrigeration lubricating oils,oil
ml
charge
indoor unit Model YDK-32-4 YDK-30-4
Power input W 80 63
capacity uF 3.5 2
Fan motor
H:1300±30 rpm
Indoor Fan Speed RPM
r/min M:1220±30 rpm 1350/1200/1050
(High/Med/Low)
L:1150±30 rpm
Indoor fan dia.*length mm φ107.5×799
Rows*Tubes*Circuits 2*18* 2*17*
Tube pitch* row pitch*Fin
mm 17.6*13*1.35 21*12.7*1.6
spacing
φ7internal threaded
Tube outside dia.and typ mm φ7internal threaded pipe
pipe
797*212*26
Coil length x height x width mm 875*357*25.4
766*106*26
Indoor Air Circulation (High/Med/Low)
m3/h 950 1050
(actual/label)
Indoor Noise Level dB (High/Low)
dB(A) 49/47/45 42-48
(actual/label)
Dimension (L*W*H) mm 1020×320×210 1080*308*225
1130×390×295(无附件)
Packing (L*W*H) mm 1275*392*318
1235×390×295(有附件)
Net/Gross weight Kg 14/16 16/20
Model YDK-60A-6F YDK-60A-6F
Power input W 125 145
Fan motor capacity uF 4 4
Outdoor Fan Speed RPM
r/min 770 850
(High/Med/Low)
Outdoor
dia.*length mm φ460χ180 φ460χ180
fan
Rows*Tubes*Circuits 2*26* 2*26
Tube pitch* row pitch*Fin
Outdoor unit mm 25*22*1.8 25*22*1.8
spacing
condensor φ9.52internal threaded
Tube outside dia.and typ mm φ9.52internal threaded pipe
pipe
Coil size :length x height x 728*650*22 728**650*22
mm
width 762*650*22 762*650*22
Outdoor Noise Level dB (High/Low)
dB(A) 56 56
(actual/label)
Dimension size (L*W*H) mm 870×310×700 875×315×680
CS-25H3A-V85AY1、CS-35H3A-M85AH4
CS-51H3A-P**AH4A(85)
13
CS-61H3A-P85AE2(85)
CS-70H3A-T**AS(38)
14
KFR-70GW/X1c(85)
15
7.2 Outdoor uni
KFR-25GW/AGX1c 、 CS-25H3A-V**AY1 、 KFR-35GW/AGX1c 、 CS-35H3A-M**AH4 、 KFR-51GW/BGX1c 、 CS-51H3A-P**AH4A 、
CS-61H3A-P85AE2
CS-70H3A-T**AS、KFR-70GW/X1c
16
8.PCB principle chart
8.1、38 section of crystal color ordinary schematic diagram
1 2 3 4 5 6 7 8
GND
JLC0301 D5
E1 E2
C21 C22 C1 C2 C3 E3
471 10A
104/275V 104/275 104 220UF/35V 104 104
U 火线 FUSE L2 IN4001 1000UF/35V 220UF/16V 配灵通3号遥控器 七灯 显示板
2
变压器 Q6 运行 A
U1 JLC0301
U2
D F3A 250V B
CN4T
+5 D
变压初级 E4 Q0 定时 E
火线由压机的COM端进入 22UF/25F +5 GND
Q1 强力 D
5 R12 R11
C13 8 1 2 3 7
IC7 CN1 Q7 经济 F
104 10K 10K
COM
C17 9 MC2003 4 AT24C02 4 Q2 制冷
压机 +5 6 5 CLOCK
CM CN 52C-1A
104 1 10 P04 R28 4.7K Q4 除湿
火线
7 27 GND
R29 4.7K 5 DATA Q3 通风
GND
11 P05 C28
2 6 28 C3 C2
Q5 制热
P31 102
18 102 102
电加热
CNM R27 51
CN 52X6A 3 12 5 P06 19 P32 GND CLOCK 5
29 R26 51
2
1
8
9
步进电机 20 P33 DATA GND
4
U1 13 P07
C15 C16 +5
MR
Vss
CLK
B
20S X3A 4 4 30 102 102
四通阀 IC1 14
+5
GND 单冷heat/cool
B HSTP.0 /双温 TYPE1.0 R8 R9
74ALS164
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
P03 4.7K 4.7K
16 1
电加热 52X6B 26 P12 D11 4148 D9 4148 D7 4148
1
3
4
5
6
10
11
12
13
C 外风机 15 C
FMO X4A 2 P11 HSTP.1 电加热/无 TYPE1.1
外风机 52X4B 32
dhon/off
R7
R4
R8
510*8
R3
R2
R9
R6
R5
FMC
14 3 P10 31 P13 D12 4148 D10 4148 D8 4148 +5
换向阀 52X5B 2
8 8 COM1 LED2
JZC-7F*2 Q4
7 P23 R10
9012
GND 4.7K LED1
压机 52CB
COM1 LED6
D6 R13 4.7K 1 D1
P02 25
+5 R32
BZ Q3
IN4148 Q2
1815 R12 Q6 4.7K LED7 LED4
9013 P25 9012
R33 GND R7 4.7K BUZZ
9
2K 4.7K
P01 24 COM3 LED3
D2
LED5
CNU
C23
B C24 3
L1 102 +5 R30
104/275V U2 GND GND 6
N
4.7K COM3
5 Q5
改为跳线,保留孔位 P24 R11
CFI
+5 8 9012
C20 1 IC6
4.7K
1.2uF 473/275V R14 e d c b g h a f
B 3 R6 4.7K COM2 B
1 390 P00 23 6 P22 a a LED
2 BCR IC5 DPY-8*2
1 f b f b
R36 4 R31 g g
220
R37 330
+5 7 COM2 e c
6 4.7K 2 dp e c dp
3
2 +5 13 Vcc d d
MC3021 Q7 GND C4 104
+5 1815 R16 GND
com2
com1
10K 10
E5
R34 E8 应急键 SW1
2K 1uF/50V P34 接收头
21 2 S
Q8 10uf/16F CND RMT
C14 R35 +5 S 3
9012 GND 102 12 4.7K +5V 3 2
-+
GND GND 1 GND 1 HS0038
R25 /RESET R24 10K
R39
11 P30 R23 4.7K S 2
10K R38 510 17 3 +5V R1 51
10K E1 22UF/16V
C12 +5 风机 反馈 GND 1
+5 102 R22
3
GND 510
3 C19
R19 XL R15 104
产品名称 (37544)38款晶彩普通电控原理图
1
CNTR0 4.7K
1
R3 10K
GND GND P21/AN1 5 AC..ZERO
GND R17 510 R5
P20/AN0 4 C11 R2 绘 图 姚贤清 批 准
3
4.7K
Tp管 INT0 R4 10K 102 4.7K
Vss
C7 R18 C6 16 22
标准化 杜 娟 日 期
4
FUSE+ZR L1 IC6
FUSE 10 A- 180 -62 1 B
R1 1
7805
3
+5 编号 JS2-B65aC-M11A/0
火线 Vin Vout
GND
51/2W
250V/3.15A CN B T1 CN C
E1
C21 C1 E2 C2
2
火线 B Xi n
52CB 1 10 7 17 步进 电机
低风 P3 0 GND IC3
R30 2003 +12
C3 300K XL1 1 16 TP2
CN E3
Xo ut 15
t。
8M IN 1 OUT 1
8
20S
X1B
52X6A IC2B
GND R16 +5
104
9
换向 阀 P2 5/ AN5 CNG1 R35
6 15 2 22 C13 4.7K R17
电加 热 P3 7 TP t 。 4.7K
104 C14 4.3K 管温
IC2A 104
GND 金膜
R18 TR t 。
52X6B P2 4/ AN4 8 GND 室温
7 16 1 23 C23
电加 热 压机 +5 P0 0 C15 4.7K R19
NC COM 104 C16 GND
4.3K C21
104 E7 104
52CA E10 10UF
R33 GND 金膜 104
8 2K AA 25v AA
4.7uF/50v +5V
Q1 R20
GND L
9012 IC4
11 P2 2/ AN2 6 R27 10K R22
CN 12 0
R32 R34 4.7K C17 D5 200K/2W
P07 P21 P20 103
10K RE SE T IN4007
R31 510Ω DEFROSTER
B 10K
R21
GND B
DA1 DA2 DA3 DA4 DA5 DA6 P0 6 29 R26 10K IC5 R23
IN4148 IN4148 IN4148 IN4148 IN4148 IN4148
*
化霜
GND TYPE_IN1
4.7K +5 103 C18 D6 200K/2W
R10 R8 1 IN4007
P1 2 IC8 FEED
4.7K 4.7K 32 5 SDA GND 4
P1 0 GND
TYPE_IN2
6 3
P1 1 31
R11 R9 2 SCL A2
P1 3 外反 馈
4.7K 4.7K 4.7K 4.7K 7 WP A1 2
R7 R6 3 R28 R29
+5 P1 4 8 VCC A0 1
GND 10K 4.7K C5 +5V +5
102 24C02
P11 P10 Q2
E5 C4
GND R3 R24
4 *
390Ω 390Ω P2 0 100uf/25V 104
* 10K
SW1
4.7K
7
R5 R4 +5V COM1 9012 C7 P2 3/ AN3 GND
二极管 无 有 102 R25 4.7k C19 AR5 GND
GND +5V Q3 +5 104
DA5 无 室外传感器化霜 RMT_IN R12GND Vc c 13 金膜
(37544)诚丰65款主控/电源板原理图
5 GND 可调电阻 产品名称
DA1 单冷 双温 4.7K
P2 1 E8 C20
A CLK 100uf/25V 104 GND A
DA2 双温无电加热 双温有电加热 +5V COM2 9012 102
设 计 张建 审 核
DATA C6 C8
DA3 智能化霜 外板化霜 102 Q4 GND
DA4 灯板显示 数码管显示
COM1
E4 R2 GND 30 P0 7 Vs s 16 绘 图 范丽英 批 准
化霜参数调节(请参看说明书)
COM2 GND100UF/25V 4.7K Vr ef 10 E10 C22
AR5 22UF/25V 104 标准化 日 期
COM3 9012 102
C9 M 3 7 54 4 G2 A S P
CN1 +5 佛山市中格威电子有限公司
GND
1 2 3 4 5 6 7 8
17
8.3、85 section of schematic diagrams
1 2 3 4 5 6 7 8
U1
3.15A 250V
621-10-126
L CNB Z D5 B IC5 7805 +5 编号 JS2-B85aC-T01A/0
火线 U TRANS CNC 1 3
FUSE 1 2 Vin OUT
GND
C2 IN4007
ZR C1
4 3 E1 C30
S C25 E2 104 E9
零线 104/275V 变压 器 1000UF/35V
CN1 104/275V E F -1 0 05 GS1 IN4007 104 220UF/25V 22UF/16V
2
初 级 次级 D1--D4
2
D 1 S1 U1 D
负离子
X5B B C23 104 GND CNG
CNA IC1
52C( 12V) 火线
U BZ
R33 2003
TMP86F809NG
30
IC14 R26 10K 管温
9 8
4 7 3 /2 75 V
GND
X5A
NO B COM CLAMPCOM
C1 2K C32 31 R27 10K
CM 室温
953-1A U 10 7 R47 4.7k 102 17
压机
OUT 7 IN 7 C20 C21 R31 +5V
52X6 C17 R30
HEAT NO 净化 CNL 104 104
COM R2 11 6 P12 24 4.3K
B OUT 6 IN 6 104 4.3K 104 C16
HF2160-1A-12DE GND GND
12 5 15
电加 热 外风 机 X1A OUT 5 IN 5 VDD 5
+5 GND
52X5A 220 IW
20S B U1 13 4 16 C31 E8 +5
四通 阀 换向 阀 X2A OUT 4 IN 4 104 100UF/25V
VSS 1 GND
18
52X4A 电加 热 52X6A 14 OUT 3 IN 3 3 R32
3
CNM +5
FMO X5B U1 TEST 4 10k
外风 机 GND
FMC +5V 25 R25 4.7k 2
压机
15 OUT 2 IN 2 2 P11 23
52CA
L3 C19
+5 C15 1
C3 10 4 / 2 75 V R3 B E3 100UF/25V 16 1 14 102 102
N1 330 OUT 1 IN 1 GND
C 5 GND C
IC4 4 1 6 GND R10 GND
CFI 4.7K
1 . 2 U F/4 5 0 VA C R1 6 2 P10 22 R42 10K
MF1 BT131 C34
7 GND
1 220 IW IC2 C24 Q2
R46 102 19 102 1815
内风机 C 35 C26 102
390 20 R9 10K
4 7 3 /2 75 V GND Z
21 GND C27
R8
XOUT 3
R21 220 103 4.7K
RX 8M XL
27 300K
XIN 2 +5 GND
220 R20 26 GND
C37 C9 C14
29 IN4148
102 102 R43 D6
104
220*3 10K
6 R19 28
GND E7 4.7UF/50V
5 R22 RESET 8
10 GND
4
R23
3 11 CNP
C13 C12 C11 32 R28 10K
2 12 1
+5 102 102 102 C22 +5V +5V 2
1 R29 C18
B 9 104 104 管温2 B
R14 R15 R18 R17 R16 13 4.3K
C36 C33 E9
104 CNE 104 GND R13
10k
GND +5 D12 D10 D8 强制 按键
22UF/16V R24 GND
10k*5
GND +5 R44 C6 104 4.7k
4148 4148 4148 GND B C7 SW1 GND
102
4.7k C28 D11 D9 D7 R39 R40 R37 R36 IC16
+5 R45 4.7K 1 16
102
4148 4148 4148 2 IN 1OUT 1 15 GND
C29 3 IN 2OUT 2 14
4.7k GND IN 3OUT 3
4 IN 4OUT 4 13
1 00 u F /25 V +5V 102 5 IN 5OUT 5 12
E6 +5 +5 6 IN 6OUT 6 11
GND 7 IN 7OUT 7 10
IC5 24C02 8 COM
CLAMP 9
1 8 R4 10K R41 R38 R35 R34
A0 VCC R11 R12
4.7k*2 4.7K 2003 GND
2 7 IC13
A1 WP GND 12 RCK +5
3 6 R6 51
A2 SCL Q1 +5
4 5 QH 7
GND SDA 9013 16 VCC
QG 6 1
IC15 2003
16 M70内核东芝809芯片85款(简易三灯)
R7 51 10 SCLR IN 1OUT 1 产品名称
GND 9 QH* QF 5 2 IN 2OUT 2 15 CNM2 CNM1 CNM
电控原理图
C8 C10
R5 QE 4 3 IN 3OUT 3 14
A 102 102 4.7K QD 3 4 IN 4OUT 4 13 A
GND CLOCK14 SI QC 2 5 IN 5OUT 5 12 设 计 审 核
DATA 11 SCK QB 1
6 IN 6OUT 6 11
GND 7 10
QA 15 8 IN 7OUT 7 9 绘 图
+5 E5 13 G COM
CLAMP 批 准
8 GND E4 B B B
GND
B 标准化 日 期
47UF/25V M74H595 100UF/25V
C5 104
佛山市中格威电子有限公司
GND
1 2 3 4 5 6 7 8
8.4、Three water chestnut 18NV 85 section of entire compatible electrically controlled schematic diagrams
1 2 3 4 5 6 7 8
B +5
FUSE FUSE+ZR U1
安规电容 1
Vin OUT
3 编号 JS2-B85AC-M01A/0
L
L1
GND
4 3 D1-D4
火线由压机的ON端引人 4001
C12 IC4
AC-N 104/275 C2 7805 E3 C3
2
1 2 E1 C1 E1 104 104
470UF/25V
TRANS 1000UF/35V 104 470UF/50V
D 零线 D
N
HI GND
X3B U1 IC1 B C5
+5
IC1 P 07 30 R9 220
D6 4148 D8 4148 D10 4148 R33
MI D X4B B IC4C 9 104 GND
4.7K
低风 X5B
15 2 9 P2 5/A N
MF1
X5B 2003
LO IC4D P 10 31 R10 220 4148 D9 4148 D11 4148 R32
14 3 8 P2 4/A N D7
中风 X4B
4.7K
2003
IC4E 10 0 R34 AA AA 4
高风 X3B
13 4 7 P 23 P 00 23
CF CFI 2003 P 01 24 10 0 R35 BB 5
BB
IC3E
13 4 20 P33 P 02 25 100 R36 6
电加热 52X6B
X2B STB
CN H 2003
RMT
VALVE 14
IC3D
3 19 P32 2 S CN123 S 3
换向阀 外风机 X1B C22 C24 C23 2
-+
GND 47UF/16V
机 9
CLAMPCOM
8 M74H595 C11 4.3K C9 CNG 管温
B 10 7 104 104
OUT 7 IN 7
1 11 OUT 6 IN 6 6
12 5
OUT 5 IN 5
E7 13
OUT 4 IN 4
4 28 P05 GND
22uf/25V 14 3
OUT 3 IN 3
CN M 15 2 IC5
16 OUT 2 IN 2 1 +12V +5
OUT 1 IN 1 IC4F
+5
GND 2 A10 15 11 6 2 P13 AT24C02
2003 E8
步 Q3 R8 4.7K R40 R39
8 1 2 3 7 4.7uf/25F
AJ1 4.7K 4.7K
IC4E 4
进 3 12 5 3 P14 /CN TR 0 6 5
R7 22 0 2003 GND
8
BZ GND
E7
电 4 R5
+5V
2K P3 4 21 SCL
100uF/25V 15 Xo ut
5 R6 10 0
GND R44 E10
XL
P3 7 22 SDA 产品名称 三菱(37544)18NV P型板85款全兼容电控原理图
2K R41
机 1uF/50 V Q7
GND
8.00 300K +5V
A B 90 12 Vr ef 10 A
14 Xi n 设 计 审 核
1
R45 Vc c 13
E6 10K R3 51 0
11 / RES ET
C12 E5
绘 图 批 准
22uf/25VCN 16 1 R46
10K R2 4.7K 12 C NVs s Vs s 16 104 10uf/16v
GND GND
标准化 日 期
GND GND
GND
佛山市中格威电子有限公司
1 2 3 4 5 6 7 8
18
8.5、Mitsubishi Jin dynasty 85 model of simple three lamp electrically controlled motherboards
1 2 3 4 5 6 7 8
GND
D12
C6
C4 E11
IN4007 E10 104 104
L 火线 FUSE 变压器 IN4007 1000UF/35V 220UF/25V
2
D 变压器次级 D
F3.15A 250VAC 变压初级
U1 +5
火线由压机的COM端进入 GND
+5
R15
COM 10K R12
4.7K
CM CN 52C-1A R28 P11 32 D8 4148 D11 4148 D10 4148
火线 26 P03 +5
压机 SW1
GND 应急键 C22 4.7K
102
HSTP.0 单冷/双温 TYPE1.0 R9 R8
heat/cool 4.7K 4.7K
HEAT GND P12 1
电加热 25 P02 D15 4148 D12 4148 D13 4148
52X6A P13 2
B 电加热/无 TYPE1.1
C9 104 HSTP.1 dhon/off
U1 E4
20S X2A 47uF/25V C15 B
MC2003 31 P10 D7 4148 D14 4148 D9 4148
GND 9 GND
四通阀 B IC3 12 P24 8 104
5
四通阀 X2B IC5 CNM
CNE
8 COM
CLAMP 9 步进电机外风门
QA 7 IN 7OUT 7 10 5
C 21 P34 CS +5 XH-6A 6 11 C
FMO X1A 电加热
13 4 P25 9 QB
5 IN 6OUT 6 12 4
52X6B R11 220 1 QC IN 5OUT 5 3
WR S 2 QD 4 IN 4OUT 4 13 2
FMC 3 14
19 P32 GND 3 QE IN 3OUT 3 B 1
16 R6 220 4 2 IN 2OUT 2 15
外风机 压机 52CB
1 P00 23
DI 5
QF
QG
1 IN 1OUT 1 16
20 P33
6
R10 220 2003
11 IC1 C12 C16 CNM1
外风机 6 P23 7 C8
X1B 102 102 步进电机内风门
CNU
C2 L1
0C314 R35 4.7K
102
5
104/275V U1 12 CNVSS GND 4
D16
N
5 GND 3
+5 +5 B 2
CFI IC9 B 1
R26 1 4148
1.2uF 220 3 R24 +5 8 1 2 3 E5 E6
R37 4.7K 47UF/25V
1 2 BCR 390 6 7 47uf/25V
C1 IC4 R18 4.7K 4 GND
473/275V 4 1 5
R25 330 6 2 10 GND
3 7 P07 30 17 P30 IC7 AT24C02
18 P31 R38
MC3021 QA QB QC QD QE QF QG 4.7K
B
R34 15 2 P01 24 28 P05 CLK
10 0 R22
SCK 1115 1 2 3 4 5 6 7 QH
BZ
B 2K
27 P04 DATA 10 0 R5
IC2 M74HC595 8 G B
Tp管 C18
C26 R32 C20 R27 GND 102 产品名称
104 4.3k 104 小分体电控原理图(0C314芯片)
4
10K
A C14 GND GND R2 INT10 +5 A
104 GND C1815
R3 +5
CNW 设 计 陈斐 审 核
Q1 C11 10K P37 22
100μF/25V
3
CNTR0
3 104
R30 GND 16 P14 E2
标准化
1
9. PCB function:
NOTE: Ts is the set temperature, Tr is indoor room temperature, TP1 is indoor coil pipe temperature, TP2 is outdoor
coil pipe temperature.
Display panel
[1]only two LED
①running lamp(green):power on light, flash one time/ one second during anti cooled wind.
[2]eleven LED
① running lamp(green):power on light, flash one time/ one second during anti cooled wind.
②temperature lamp(green):16~31℃ set temp. and room temp. display, light is set temp. flash is set temp.
running timer
① running lamp(green):power on light, flash one time/ one second during anti cooled wind.
fan running.
Cooling
● Start up the compressor: when the room temperature is more than Ts+1℃, compressor → start-up
● Shut down the compressor: when the room temperature is less than or equal to the set temperature Ts-1℃,
compressor → shutdown
● When the temperature of coil pipe of the indoor units is less than or equal to 1℃ for one minute and the
compressor has continuous run for more than ten minutes, the compressor and outdoor blower fan shut down
through the electric control board and the indoor blower fan is running at low speed.
● When the temperature of coil pipe of the indoor units is more than or equal to 7℃ and the compressor has
shutdown for more than three minutes, the compressor and outdoor blower fan start to run and the indoor blower
fan is running at set speed.
● When the temperature of coil pipe of the indoor units is equal to or less than -10℃ for three minutes in the
compressor has continuous run for three minutes, the compressor, indoor and outdoor blower fans and swinging
wind shut down. Restart up six minutes later; if the above situations appear again within six minutes, all the
outputs are shut down through the electric control board and display failure.
● When you press turbo button of remote, the air conditioner enter turbo running, compressor and outdoor blower
fan turn on all along, indoor blower fan run at high speed, turbo indication is light.
● After the compressor runs five minutes, the lamp flashes 4 times per six seconds or display E4 if the temperature
of indoor coil pips is more than 25℃ in the continuous 20 minutes. The controller will automatically shut down if
the temperature of indoor coil pips is more than 25℃ in another continuous 20 minutes, that is the abnormality
protection of outdoor units and the indicator lamp keeps its former state of flashing. If the temperature of indoor
coil pips is less than 25℃ in the second 20 minutes or the compressor shuts down, the electric control board will
store to the normal display and the time is restarted when starting up the compressor next time.
20
Tr
7° C
1° C
-10° C
c
o
m
p
r
e
s
s
o
r
ob
ul
t
do
ow
oe
rr
f
a
n
dl
oo
ow
re
b
r
f
a
n
Tr
c
o
m
p
r
e
s
s
o
r
d
oo
o
re
b
l
w
r
f
a
n
● Start up the compressor: when the room temperature is less than Ts-1℃, compressor → start-up
● Shut down the compressor: when the room temperature is more than or equal to the set temperature Ts+3℃,
compressor → shutdown
● The electric heating start-up in the heating mode shall meet the following conditions: ① start up the compressor
21
and indoor blower fan ② none defrost ③ TP1< 49℃ ④Tr ≤20℃.
● The electric heating shutdown in the heating mode shall meet one of the following conditions: ① shutdown
indoor blower fan ② Tr ≥ 23℃ ③ TP1≥50℃.
● In the heating mode, the indoor flower fan can be set as high/ medium/ low /automatic running mode by remote
control however the anti cool air function is prior. In the heating mode, the anti cool air control function is to
control shutdown of the indoor blower fan by detecting the temperature of coil pipe of evaporator so as to attain
the purpose of preventing cold air from blowing.
● For the waste heat emission function in the heating mode, in principle, the indoor blower fan shall be on for
fifteen seconds after the electric heating is closed.
● When the temperature of coil pipe of indoor units is more than or equal to 56℃, the outdoor blower fan shuts
down and it enters the overload protection; when the temperature of coil pipe of indoor units is less than or equal
to 52℃, the outdoor blower fan starts up and it exit the overload protection.
● When the temperature of coil pipe of indoor units rises to 63℃, the compressor and outdoor blower fan are closed
and two minutes later, the change valve is closed. The indoor blower fan is running at the set speed. Restart up six
minutes later; if the above situations appear again within ten minutes, all the outputs are shut down through the
electric control board and display failure.
● When you press turbo button of remote, the air conditioner enter turbo running, compressor ,outdoor blower fan
and four-way valve turn on all along, indoor blower fan run at high speed and it must meet start condition, turbo
indication is light.
● After the compressor runs five minutes, the lamp flashes 4 times per six seconds or display E4 if the temperature
of indoor coil pips is less than 30℃ (heating) in the continuous 20 minutes. The controller will automatically shut
down if the temperature of indoor coil pips is less than 30℃ in another continuous 20 minutes, that is the
abnormality protection of outdoor units and the indicator lamp keeps its former state of flashing.
22
Tr
Tr
+ -
3 1
over 6 MIN
outdoor
start-up start-up start-up
blower fan
23
Tr
36
c
o
m
p
r
e
s
s
o
r
dl
oo
o
re
b
w
r
f
a
n
In the heating mode, the electric control board checks and compares the temperature of indoor room and indoor coil
pipe after the compressor works for a while; judge whether the outdoor heat exchanger part is frosted or not according to
conditions such as the change of indoor coil pipe temperature; if it is judged as frosted, it automatically enters defrosting
process. When defrosting, close the indoor and outdoor blower fan and four-way valve.
Tr
TP2
c
o
m
p
r
e
s
s
o
r
ob
ul
to
dw
oe
or
r
f
a
n
dl
oo
ow
re
b
r
f
a
n
25
TP2
26
Tr
Tr
TP2 r
o n
a n
a
n s
s rrf f
r
o a n
a e o rer
s rrf f r o
d e
w o w
s
e o
o e rer p
m t o o
d o
r
p d w o
o w o u
o l
b l
b
m
o
c
t
u
o
o
l
b
d o
l
b
c
Tr
TP2
r
f
a
n
defrost
compressor start-up shutdown start-up shutdown start-up
outdoor
start-up shutdown start-up
blower fan
our-way
valve start-up shutdown start-up
dl
oo
ow
re
b
r
f
a
n
Dehumidification
Dehumidification running is to eliminate the water vapor in the air by using the cool circulating capacity, but the
dehumidification will not decrease the indoor temperature in great deal. The air conditioner automatically repeats on
and off circulation according the room temperature, which is shown in the following figure.
27
Tr
°C
°C
Tr≤10℃
indoor
low speed
blower fan
forbid
dehumidify
start-upshutdown start-up shutdown shutdown start-up shutdown start-up shutdown
dw
oe
or
rf
b
l
o
a
n
shutdown
● In the dehumidification mode, the indoor fan is running at the low speed for twenty seconds at first, then it select
working mode.
In the ventilation mode.When ventilating, the compressor, outdoor blower fan, four-way valve and electric heating are
all closed and the indoor blower fan is running at the set speed.
Tr
c
o
m
p
r
e
s
s
o
r
ob
ul
to
dw
oe
or
r
f
a
n
dl
oo
ow
re
b
r
f
a
n
Automatic mode
● Conditions for entering the automatic running mode are: After power-up for the first time, start up and select the
automatic operating mode of remote or press emergency key, the working mode depends on Tr and if the working
28
mode had set , it doesn’t change by Tr and the default set temperature is 25 ℃.
T
r
26° C
2
1
2
5
m
o
d
e
When the time on or time off is used, the clock of remote controller shall be corresponding to the current clock and the
timing times is less than or equal to 24 hours, when the timing time is reached, unit will start-up or shutdown.
Sleep function
When the sleep key is press, air conditionerenter sleep state, indoorblower fan running at low speed, only sleep
indication display.
There is a forcible execution key on the panel of indoor units and the air conditioner can run by pressing the key when
the remote control is out of work or missing.
When pressing down the forcible execution key, then power up and enter the self-check program.
Failure display
29
off state SEC at on/off sensor fault (the resistance is 5КΩ in the normal temperature
state 25℃), when it is abnormal the sensor should be
replaced.
2、Check whether there is short circuit or open circuit in
the wire of the sensor, and whether the plug is
connected well, whether there is welding off or
rosin joint on the electric control board, if there is
any, it should be repaired.
3、When the 1 and 2 are both normal, then the
components or integrated circuit is damaged, the
electric control board should be replaced.
1、Check whether the resistance of the sensor is normal
(the resistance is 5КΩ in the normal temperature
25℃), when it is abnormal the sensor should be
replaced.
2、Check whether there is short circuit or open circuit in
display
display at flicker 3/5 coil temp. the wire of the sensor, and whether the plug is
E3 at on/off
off state SEC sensor fault connected well, whether there is welding off or
state
rosin joint on the electric control board, if there is
any, it should be repaired.
3 、 When the 1 and 2 are both normal, then the
components or integrated circuit is damaged, the
electric control board should be replaced.
1、 Check whether the winding resistance and
operation current of the compressor are normal.
2、Check whether the high and low pressure is normal
when the unit is running.
3、Check (whether the coil pipe sensor is normal)
whether the contact of the inserter on the circuit
board is well, the coil pipe temperature sensor is
display fixed, the evaporation of the indoor unit is well,
display at
flicker 4/6 at off outdoor unit the key is to check the evaporator temperature
E4 on/off
SEC state abnormal detected by the coil pipe temperature sensor has
state
reached the cooling or heating temperature.
4、Check whether the surface of the condenser is too
dirty, it should be cleaned when it is too dirty.
5、Check whether the capacitance of the outdoor motor
and the fan is damaged, it should be replaced when
it is damaged.
6、If the above items are normal, the electric control
board should be replaced.
1、Check whether two sets of plugs on the outlet end of
the motor have loosed from the socket of the
PG motor display no feedback electric control board, insert it firmly when loosing.
flicker 5/7
E5 display at at off signal of indoor 2、Check whether the indoor motor has damaged, the
SEC
off state state fan motor should be replaced when it is damaged
3、 Check whether the controllable silicon and other
components on the electric control board have
30
damaged, replace the controllable silicon or electric
control board when they are damaged.
1、Firstly check whether the indoor fan is normal.
PG motor display 2、Check whether the signal outputting from the
flicker 6/8 no over zero
E6 display at at off integrated chip of the electric control board is
SEC signal
off state state normal, the electric control board should be
replaced when the signal is abnormal.
1、Check whether the winding resistance and operation
current of the compressor are normal
2、Check whether the high and low pressure is normal
when the unit is running.
3、Check whether the indoor and outdoor wiring is
right; when it is wrong, connect them again
according to the circuit diagram
display 4、 Check whether the contact of the inserter on the
display at flicker 7/9 outdoor
E7 at off circuit board and the connection are well, otherwise
off state SEC feedback fault
state repair.
5、Check whether the signal feedback wire is
disconnected, replace or connect the feedback
signal wire.
6、Check whether the supply power is phase-lacking or
phase opposition.
7、Check whether the AC electromagnetic contactor is
well.
1、Check whether the filter of the indoor unit is dirty or
blocked, and clean if it is dirty.
2、Check whether the indoor fan is running normally,
display frost and replace the motor if it is abnormal.
display at flicker 8/10
E8 at off protection/over 3、Check whether indoor pipe temperature sensor is
off state SEC
state heat protection normal, and replace the sensor if it is abnormal.
4、Check whether the system pressure is normal, if
abnormal, should check whether there is leakage,
and fill the refrigerant again.
31
10. TROUBLE SHOOTING
Indoor Tr sensor
error
NO
Is CN (Tr sensor connector)
Connect CN properly.
connected properly?
YES
YES
NO
Is CN (TP1 sensor connector)
Connect CN properly.
connected properly?
YES
NO
Is TP1 sensor resistance value
Replace TC sensor.
(5KO at 25? ) normal?
YES
32
Only indoor fan motor does not operate.
<Primary check>
(1) Is it possible to detect the power supply voltage (200-240V) between L and N on the terminal
block?
(2) Does the indoor fan motor operate in cooling operation?
Does
compressor YES
continue to
operate?
NO Is it possible to detect AC
220V between NO Replace main
pin(high/middle/low) and
P.C. board.
Start to operate indoor pin(common) of motor
unit in cooling connector .
operation at airflow
level “LOW”,wait
three minutes..
YES
NO Replace
Is capacitor of indoor fan ok?
capacitor
YES
33
Compressor does not operate.
Turn on power supply.
<Primary check>
(1) Is the room temperature higher than the preset temperature in cooling operation?
(2) Is the crossover cable connected properly?
Does OPERATION NO
Check power supply.
indication indicate?
YES
Is it possible to detect AC
220-240V on terminal NO Microcontroller is defective or
Replace P.C. board.
block or contactor of miniature relay is defective..
compressor?
YES
YES
Is compressor motor NO
winding normal?(Check Compressor is defective. Replace compressor.
winding resistor.)
YES
Is capacitor for NO
Capacitor is defective. Replace capacitor.
compressor normal?
YES
NO Replace overload
Is overload relay normal? Overload relay is defective.
relay.
YES
NO
Does compressor start? Compressor is defective. Replace compressor.
YES
YES
YES
YES
Compressor is defective. Replace compressor.
34
Press START/STOP The unit does not beep at all.
button. OPERATION indication on
indoor unit is not indicated.
Is transmission NO
mark indicated?
YES
YES
Does indoor unit
Is there any thyristor NO NO operate when
fluorescent light moving remote
nearby? control near receiver
YES or indoor unit?
YES
YES Press START/STOP
button.
Batteries are
exhausted.
YES
Does radio sound is
affected by remote
control when a NO
signal is transmitted
at distance of 5 cm
from radio?
YES
Remote control is
defective.
P.C. board is
defective.
35
Trouble shooting Trouble
YES YES
Does outdoor unit run? Is the power normal? check NO Check the wiring of indoor and
the voltage between L&N of
outdoor
terminal block
YES
NO Check the
Does the YES
compressor ,wires
compressor run and it’s Does the control NO
normally? Press the power ON/OFF button
capacitor. ok?
of wire control or remote control
YES
YES Does the beeper NO
Does the indoor Normal Control failure
unit run? beep?
YES
NO YES Does the control
PCB ok?
Check the failure code NO Is the display all
according to the failure off?
table
YES
NO
Check the connector on display
PCB connected to control PCB Control PCB failure
Check the display PCB itself
36
Indoor unit and outdoor unit don’t operate
YES NO
Find the reason and NO Is the insulation of Press emergency key, does Replace remote
YES
replace the failure indoor unit and outdoor the air conditioner receiver or display
componet. unit no problem? running? panel.
YES
NO
YES
NO
NO Is the resistance of each NO
Rreplace the failure Does the transformer has
main component no Replace transformer.
componet. output?
problem?
YES
YES
normal
37