Professional Documents
Culture Documents
W1900 PDF
W1900 PDF
Compact, lightweight,
dependable
2 // 3
Tremendous milling performance
comes as a standard feature
Milling depth (cm)
32
30
28
26
24
22
20 Hard asphalt
18
16 Soft asphalt
14
12 Most frequent operating area
10
8
6
4
2 Advance rate
0 (m / min)
0 2 4 6 8 10 12 14 16 18 20 22 24 26 24 Theoreti-
cal milling
performance
0 500 1.000 1.500 2.000 2.500 3.000
(m² / h)
Perfect milling results in the r emoval of thin
pavement layers.
The performance diagram for the milling depths of up to 320 mm easily of up to 10,000 m² in the field when
W 1900 is an effective tool for the in just a single machine pass. removing 40 mm thick asphalt layers.
machine user, as it enables him The compact W 1900 makes the The diagram gives impressive proof
to roughly estimate the expected most of its potential also when of the high milling performance which
theoretical milling performance. used for the large-scale r emoval can be achieved with the W 1900
Our large milling machine is capable of surface courses. It achieves a machine.
of removing asphalt packages at tremendous daily production rate
4 // 5
Ease of operation –
high milling performance
Ergonomically
and clearly designed
operator’s platform
Milling machine operators can
familiarize themselves with the
control system of the W 1900 in no
time at all as handling requires only
a few simple steps: the controls
are arranged within easy reach and
within the operator’s immediate
field of vision, and are labelled in a
clear and language-neutral fashion.
In addition, two steering wheels
enable operation from the left or
the right.
6 // 7
Automatic levelling system LEVEL PRO
meets all requirements
Switchover Horn
button
Set value
Set value UP / DOWN
Controller Cylinder
output UP / DOWN
Memory 1 Memory 2
Different types of sensors, such Set and actual values of the left
as wire-rope sensor, slope sensor and right milling depths and of
or ultrasonic sensor, can be se- the cross slope are shown on
lected or de-selected during the large, easy-to-read screens.
milling operation as required.
Set values can be pre-pro-
Control of the milling depth can grammed on both sides, saved in
be effected by sensing along a the system’s memory and called
wire with a transducing sensor, up as required.
or by non-contact sensing of a
wire or reference surface.
8 // 9
Versatile drum assembly guarantees
full utilization of the W 1900’s capacity
The W 1900 goes it alone on the plications. The milling drum assem-
construction site when equipped bly scores top marks also with the
with FCS Light. The field-proven hydraulically height-adjustable side
system offers a broad range of appli- plates, which permit milling along
cations, for it enables milling drums road fixtures. Not to forget the hy-
of equal width but with different tool draulically a
djustable scraper blade:
spacings to be changed quickly and it is adjustable in height in order to
easily. A wide variety of additional load all or part of the milled material,
jobs in the surface treatment of road or to leave it behind in the milled cut.
pavements can thus be carried out
economically with fine milling ap-
10 // 11
Milling economically with the HT22
quick-change toolholder system
4
2 100 % increased maximum wear
path
12 // 13
Fit for the big jobs with
powerful material loading
14 // 15
Making swift headway even on sites
where space is limited
Gain valuable
operating time
16 // 17
Intelligent engineering – high-quality
components and production
We rely on quality
“made in Germany”
18 // 19
Technical specification W 1900
Milling drum
Milling width 2,000 mm
Milling depth * 1
0 – 320 mm
Tool spacing 15 mm
Number of tools 162
Drum diameter with tools 980 mm
Engine
Manufacturer Daimler Chrysler
Type OM 502 LA
Cooling water / air (intercooler)
Number of cylinders 8
Rated power at 2,000 min -1
340 kW / 455 HP / 462 PS
Maximum power at 1,800 min -1
350 kW / 469 HP / 476 PS
Displacement 15.9 l
Fuel consumption, full load 84 l / h
Fuel consumption in field mix 34 l / h
Emission standards EPA Tier 3, EC Stage 3a
Electrical system 24 V
Tank capacities
Fuel tank 850 l
Hydraulic fluid tank 270 l
Water tank 1,600 l (+ 1,000 l additional water tank)
Driving properties
Travel speed in milling gear, max. 0 – 29.5 m / 20 min
Travel speed in travel gear, max. 0 – 4.5 km / h
Crawler tracks
Crawler tracks (L x W x H) 1,600 x 260 x 550 mm
Loading the milled material
Belt width of primary conveyor 800 mm
Belt width of discharge conveyor 800 mm
Theoretical capacity of discharge conveyor 290 m3 / h
Shipping dimensions
Machine (L x W x H) 6,600 x 2,550 x 3,000 mm
Discharge conveyor (L x W x H) 8,500 x 1,300 x 1,150 mm
* = The maximum milling depth may deviate from the value indicated, due to tolerances and wear.
1
Equipment features of W 1900
Standard equipment
Basic machine Machine and levelling control
Air compressor system Digital electric height indication
Large storage compartments for cutting tool containers Automatically engageable hydraulic traction control
Highly effective soundproofing of entire engine compartment (flow divider)
Standard painting in Wirtgen white with orange stripes Automatically engaging maximum milling speed control
Milling drum assembly Freely selectable steering modes of crawler tracks
Automatically engaging high-pressure water system, 3.5 bar,
Hydraulically lifting drum plates
45 l / min
Additional lock-valve for scraper blade
Engaging water injection in milling chamber
Additional control switches for scraper blade and steering
Engaging water spray system at primary conveyor
functions at ground level
Right-hand side plate in hinged design Operator’s platform
Hydraulically opening scraper blade with convenient lock Convenient control panel with practical switches
mechanism Lockable covers for control panels
Replaceable wearing segments on side plates Individually adjustable driver’s seat
Hydraulically lifting side plates, clearance 330 mm Vibration-damped operator’s platform
Milling drums Access left and right with convenient fold-away ladder
Exterior rear view mirror
Standard assembly with milling width 2,000, HT22
Multiple-use ejector system Chassis and height adjustment
Loading of milled material Extremely wear-resistant polyurethane track pads
4-track steering
Discharge conveyor slewing angle left 45 degrees
Height adjustment via proportional valve control
Discharge conveyor slewing angle right 45 degrees
Conveyor system with adjustable conveying speed Miscellaneous
Hydraulically lifting primary conveyor Lighting package with 11 spotlights
Comprehensive tool kit
Comprehensive safety package with 5 emergency stop buttons
Optional equipment
Basic machine Loading of milled material
Special painting in one or several colours Hydraulically operated folding discharge conveyor, long
Milling drum assembly Machine and levelling control
Milling drum housing for milling width 2,000 mm, LEVEL PRO automatic levelling system
FCS-Light Additional LEVEL PRO control panel
Pneumatic cutting tool driver and extractor Slope sensor
Mounting carriage for milling drums Operator’s platform
Milling drums Canopy
Milling drum with milling width 2,000 mm, HT22, Miscellaneous
LA8 FCS
Additional water tank 1,000 l
Milling drum with milling width 2,000 mm, HT5,
Hydraulically operated high-pressure water cleaner,
LA6x2 FCS
150 bar, 15 l / min
Milling drum with milling width 2,000 mm, HT22,
LA15 FCS-Light
20 // 21
Technical specification W 1900
Dimensions in mm
14,200
13,550
10,950
6,730
Special equipment:
additional water tank
Special equipment:
canopy
4,500
3,000*
3,600
3,000
Special equipment:
folding conveyor
1,000
120 800
Machine weights
Empty weight of machine without filling media, without conveyor 25,400 kg
Operating weight, CE* 26,680 kg
Operating weight, max. (full tanks, full range of equipment) 31,900 kg
Weights of filling media
Water tank filling in kg 16,000 kg
Diesel tank filling in kg (0.83 kg / l) 700 kg
Optional equipment features increasing / reducing empty weight
Driver and tools
Driver 75 kg
Weight of 5 cutting tool containers 125 kg
On-board tools 30 kg
* = Weight of machine with half-full water tank, half-full fuel tank, driver (75 kg) and tools.
Optional equipment features increasing / reducing empty weight
Optional milling drums in lieu of standard
FCS Light milling drum assembly, milling width 2,000 mm,
660 kg
milling depth 0 – 320 mm, number of cutting tools: 162
Optional additional equipment
Canopy in lieu of standard 250 kg
Folding conveyor in lieu of standard 360 kg
Additional water tank 1,000 l (unfilled) 820 kg
Dimensions in mm
45°
800
1,300
2,500
1,550
1,400
235
131
160
45°
22 // 23
Wirtgen GmbH
Reinhard-Wirtgen-Straße 2 · 53578 Windhagen · Deutschland
Tel.: 0 26 45 / 131-0 · Fax: 0 26 45 / 131-392
Internet: www.wirtgen.de · E-Mail: info@wirtgen.de
Illustrations and texts are non-binding and may include customized fittings. Subject to technical changes.
Performance data depend on operational conditions. No. 2176189 EN-09/14 © by Wirtgen GmbH 2014 Printed in Germany