Professional Documents
Culture Documents
P R O D U C T C ATA LO G
Cook Manufacturing
Corporation
A Division of
Marine Accessories Corporation
www.cook-mfg.com
Because many other brands of jack plates do not have a waterproof motor or pump, you must
find a location inside the boat for the hydraulic tank, motor, pump, and hoses. You must also
connect the hoses to the cylinder of the jack plate, fill the tank with fluid and bleed the hoses.
6 CMC Product Catalog Specifications subject to change without notice. CMC Product Catalog 7
MOUNTING HARDWARE INCLUDED WITH CMC LIFTS.
Accessories TRANSOM WASHER PLATES
Question? Electric Hydraulic Tilt N’ Trim
Why should I consider an Electric
Made of strong 3/8" 6061 T6 alloy
Hydraulic Tilt N’ Trim for my outboard You Get Power Tilt & Trim, Better Boat Handling, More
aluminum (not cast aluminum), the
CMC transom washer can eliminate engine? Speed, Lower Fuel Consumption and
bolts “biting” into transoms and can No More Back Strain!
more evenly distribute loads on high Answer.
performance engines. Hole centers: Top With the touch of a switch you can raise
Plate – 12 7/8" Bottom Plate – 9 7/8" your motor to prevent costly prop PT-130 FEATURES:
Top Washer Plate (#20022) damage. In addition, your safety is • Rated for 130 H.P. and Smaller
Bottom Washer Plate (#20032) greatly enhanced and you don’t have to Motors.
worry about serious back strain as a • 6" Set Back to Enhance Boat
result of manually lifting your engine. Stability and Performance.
POWER DIAL CUSTOM WASHER PLATES • 20° of Trim and a Total of 90°
CONTROL The top washer plate can be custom of Tilt and Trim.
This calibrated height engraved with no minimum order. Up to Question? • 1/2" 6061 T6 Extruded
control allows you to dial in 16 characters can be engraved. Aluminum Construction with
Will an Electric Hydraulic Tilt N’ Trim
the desired height of the (#20000) improve my outboard engine’s Stainless Steel Fasteners.
Power-Lift. The Power-Lift • Electric Hydraulic Actuator
performance?
will raise or lower to that Rated at 7853 lbs. of Thrust!
height and stop. Three Answer. • Standard B.I.A. Bolt Hole
indicator lamps illuminate TRANSOM WEDGES/SET BACK SPACERS
Pattern.
the up and down These 2 degree wedges are designed to give extra positive or negative trim. Absolutely! As you are operating your
movement and when in
• Convenient Adapter Kit
The wedges are used as an aid for boats with an boat Electric Tilt N’Trim will allow you to
position. It also has an Available for Clamp-on Motors.
insufficient transom angle or for boats having change the angle of your motor to
on/off switch to allow you • Four Stainless Steel Motor
planing problems at low speed. Our obtain the best performance for your
to use another switch if Mounting Bolts Included.
unique design of the CMC Transom load and water condition. As a result,
preferred for different
situations.
Wedges allows you to also use you can receive a more stable ride,
them as set back spacers, by increased top end speed, and get more
(#66100) simply inverting 2, 4, and 6 sets. prop clearance resulting in better fuel
PT-35 FEATURES:
NOTE: Hole design fits the same pattern as the efficiency.
• Rated for 35 H.P. and Smaller
The power dial accessory can Power-Lift transom bracket and standard
Motors.
only be added to a hydraulic motoring mounting.
power-lift with a position
Question? • 5 1/2" Set Back to Enhance
SIZE: 1/2" x 4" x 11 1/4" (#20122) Boat Stability and Performance.
indicator gauge already What makes a CMC Electric Hydraulic
installed. • 84° of Trim and Tilt.
Tilt N’ Trim unit superior over the
• 1/4" 6061 T6 Extruded
competition?
Aluminum Construction with
TRIM BUTTON SWITCH Answer. Stainless Steel Fasteners.
This weatherproof trim button • Electric Hydraulic Actuator
switch is made of molded black CMC Tilt ‘n Trim units feature the Rated at 7853 lbs. of Thrust!
plastic with raised white letters. most durable and powerful actuator • Accommodates Clamp-on or
It can easily be wired to the PT- available! Units are actuated with a Bolt-on Motors Without the
130 Power Tilt and Trim or totally waterproof marine electric Need of an Adapter.
Power-Lift wire assemblies.
hydraulic system that provides over • Weighs Only 24 Pounds!
(#20220) 7800 pounds of thrust, which is more
than 40% more powerful than other
WATER PRESSURE brands. Durability is also enhanced
GAUGE because it is made of 100% non-ferrous
The water pressure gauge is materials, which help reduce corrosion
sealed and drip proof and is in both salt water and fresh water. Unlike * The inside dimension of the motor mounting area of the PT-35 is 11 inches. Before
mounted in the dash of the the competition, the CMC hydraulic ordering, please make sure that the maximum width of the clamp mounting feet and/or
boat. The gauge registers from
system is completely sealed and mounting bolts of the motor that must fit into this area does not exceed this 11 inch limit.
0 – 30 P.S.I.
submersible to prevent any worry or Refer to the transom view drawings. Mounting bolts are not included with the PT-35.
(#20320) water damage.
“At the lake I was somewhat The BA-130 is rated for outboard motors up to a maximum of 130 H.P. The unit is
hesitant at first to use the mounted between the boat transom and the outboard motor. It is designed to help
throttle too hard or too fast. minimize damage to the outboard motor and boat transom only when an obstruction
After a while, I did is encountered while running at speeds under 5 M.P.H. in the forward direction. As it
encounters an obstruction momentum causes motor to deflect and rotate up to 45
everything possible to test
degrees to slide over the obstruction. A drawbar spring is incorporated in the unit to
the unit. I couldn’t be more Motor View Transom View Port View Down Port View Up help return the motor to its normal position while operating in the reverse direction at
pleased and satisfied with low R.P.M. The BA-130 is not designed to encounter obstructions while the boat is being
MODEL PT-35
www.cook-mfg.com