Professional Documents
Culture Documents
Causes of faults in electric motors and their effects 3MM Vinyl oor
RM2.6/sqft
October 21st, 2016 | Posted in Energy Efficiency - motors
Tags: electric motors , the insulation , the motor Free on site
Quotation &
Consulation
Toay, A.N. tells us about AC motors/electric motors and the causes of faults. If like him you want to discuss
a topic that you like, send us a mail and we will publish it after a short review!
NII FLOOR
Failure in electric motors may occur at start-up or during operation. Most of the electric motor failures occur at start
up due factors such as low insulation resistance, over-current or mechanical failures. Other causes include issues
with the supply, operation environment or lack of maintenance. report this ad
Subscribe to the
Newsletter :
productmanualsguide.com OPEN
Most of the motors, regardless of type and rating have a long service life and only require a minimum maintenance
to ensure they do not malfunction. It is recommended to regularly maintain the motors and associated equipment,
and to check for signs of aging of the insulation or other parts that may degrade the motor.
Select Language
Powered by Translate
A regular inspection and maintenance will help in identifying weak areas or parts that are about to fail, and rectify
them before a problem occurs.
There are six main areas where faults occur due to a variety of reasons. These areas are usually referred to as fault
zones and include the power circuit, power quality, stator, rotor, insulation and air gap.
There are also different factors that can lead to failures in the electric motors. These are likely to affect the above
fault zones in one way or another. The main causes include;
Selangor
RM 525,000
RENO 22x80
Seksyen 7 S…
Selangor
RM 699,000
Teres 2
tingkat , Bu…
Selangor
RM 680,000
Orchard Farm
With House,…
Low insulation resistance in Electric motors Pahang
Low insulation resistance is one of the most common causes of motor failures and also one of the most difficult to
handle. A low insulation resistance leads to leakages or short circuits in the coils and finally the motor malfunction RM 720,000
and failure.
report this ad
When the insulation becomes weak, it eventually breaks down and does not provide the required isolation between
the conductors or motor windings. The initial resistance of the insulation of the windings is usually very high – in the
order over one thousand mega ohms ( > 1MΩ). However, after some time, the insulation starts degrading due to
overheating or other undesirable conditions such as corrosion, physical damage and others conditions. SEARCH
To prevent such problems, the maintenance people should perform regular inspections of the insulation.
Pages
Electric motor faults due to over-Current
About us
An electrical overload or over current condition occurs when excessive current flows inside the motor windings. This Electrical Calculation Tools
is usually more than the design current the motor winding can carry efficiently and safely. An over current may occur Electrical Engineering Forum
due to various reasons; in particular a low supply voltage will cause the motor to draw more current in an attempt to How to help Electrical Engineering
maintain its torque. Another reason is when there are short circuited conductors, excess voltage etc. Community
LED lighting resources area
An overcurrent condition leads to overheating of the motor and damage to the insulation. And it is possible to
Load Shedding Guide
minimize the risk of motor failures due to over current. This can be done by using reliable over current protection, to
Make a Comment, write a Post
detect any over current condition, and interrupt the supply and hence stop the current.
Newsletters, archives
Special thanks
Recent Comments
Free on site Quotation & Consulation
Estelle Jones on High voltage fuse:
it’s rubbish!
surbhi on Underground cables:
types, advantages & disadvantages
Abbas on Solar Energy: A Look into
the future
Putta Phanindra on Transformer
differential protection
WEBSITE DIRECTIONS
Ezzat on Service life of an MV Cable
3MM
Vinyl
oor
RM2.6/
sqft
NII FLOOR
In addition, other faults in the motor such as loose bearings, misalignments, and corrosion related issues like wear
may cause the motor to have internal vibrations. This reduces the accuracy and efficiency while accelerating the
tear and wear on the moving parts that are in contact with one another.
OPEN
Moisture in AC electric motors
The moisture can cause a lot of problems to the motor by causing corrosion of various parts of the motor. In
particular, the moisture will corrode the insulation, and lead short circuit between the windings, corrode the bearings,
motor shaft and rotors.
report this ad
OPEN
This will prevent the smooth rotation, decrease efficiency and lead to complete failure of the motor.
In addition, dust particles and other small objects inside the motor may introduce some resistance that will slow
down the motor, meaning that it will have to work harder to overcome this resistance.
The dirt particles may also be abrasive in a way to damage the insulation.
Conclusion
Faults in AC electric motors are caused by simple things and can be prevented through regular maintenance,
observing the recommended operating conditions such as well ventilated, dust free environments with no moisture.
In addition, it important to have a stable supply to the motor and the appropriate over current and over voltage
protection gear.
What’s your opinion on this subject? What more can you say about the causes of faults in AC motors?
Be Sociable, Share!
Tweet Share
Solid info, thanks. Overload through mechanical issues is a sure cause. Be good to have a follow-up on
motor tests, such as insulation resistance.
Reply
Owsaam
Reply
I knew that overheating in electric motors can cause problems, but I never found out why it happens. I’ll try
and make sure that the voltage levels are correct so that my motor runs properly. I’ll refer these tips to my
coworker too!
Reply
kenon says:
2018/02/05 at 11:55 am
I am a mechanical engineer and I know this very well. These five are the major cause of electric motor
failure. Good information.
Reply
venkat says:
2018/02/13 at 10:01 pm
Reply
Leave a comment
Name (required)
Website
Submit Comment
Ad