Professional Documents
Culture Documents
Catalogue A10VO28
Catalogue A10VO28
Pump A10VO
Data sheet
Series 52/53
Size 10...85
Nominal pressure 3600 psi (250 bar)
Peak pressure 4600 psi (315 bar) Series 52
Open circuit Series 53
Contents Features
Ordering code - standard program 2 – Variable axial piston pump in swash plate design for
Hydraulic fluids 4 hydro-static drives in open circuits
Technical data 5 – Flow is proportional to drive speed and displacement. The
flow is infinitely variable by adjustment of the swash plate.
Operating curves for pumps with pressure control 8
– Strong bearings for long service life
DR - Pressure control 9
– High permissible drive speeds
DRG - Pressure control, remote 10
– High power to weight ratio
DRF (DFR) and DRS (DFR1) - pressure and flow control 11
– Small dimensions
LA... - pressure, flow and power control 12
– Low noise level
Unit dimensions, size 10 14
– Good suction characteristics
Unit dimensions, size 18 16
– Axial and radial loading of drive shaft possible
Unit dimensions, size 28 20
– Pressure and flow control
Unit dimensions, size 45 24
– Electro-hydraulic pressure control
Unit dimensions, size 63 28
– Power control
Unit dimensions, size 85 32
– Electro-proportional displacement control
Combination pumps A10VO + A10V(S)O 36
– Short response times
Overview of through drive mounting options 36
Dimensions through drives 37
Installation notes 40
General information 44
/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Nom. pressure 3600 psi (250 bar), peak pressure 4600 psi (315 bar) – A10V
Operating mode
05 5
1) For availability of control options in series 52 and 53 see index 06 in ordering code
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
A10V(S) O / 5 – V
01 02 03 04 05 06 07 08 09 10 11 12
Index 10 18 28 45 63 85
left hand L
Seals
08 FKM (fluor-rubber) V
Shaft end 10 18 28 45 63 85
Hydraulic fluids
Prior to project design, please see our technical data sheets Notes on the selection of the hydraulic fluid
RE 90220 (mineral oil), RE 90221 (environmentally
acceptable fluids) and RE 90223 (HF-fluids) for detailed In order to select the correct fluid, it is necessary to know
information on fluids and operating conditions. the operating temperature in the tank (open circuit) in
relation to the ambient temperature.
When using HF- or environmentally acceptable fluids
attention must be paid to possible limitations of the The fluid should be selected so that within the operating
temperature range, the viscosity lies within the optimum range
technical data, if necessary contact us. (when ordering
please state in clear text the fluid to be used). Operation on (nopt), see shaded section of the selection diagram. We recom-
Skydrol is only possible after consultation with us. mend to select the higher viscosity grade in each case.
-40° -13° 14° 32° 50° 86° 122° 158° 194° 240° °F
Temperature range t in °C
t min = -40°F (-40°C) Fluid temperature range t max = 240°F (115°C)
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
Technical data
Operating pressure range Maximum permissible speed (Speed limit)
Permissible speed by increase of inlet pressure pabs at the
Inlet
inlet port S or reduction of displacement (Vg ≤ Vg max ).
Absolute pressure at port S
pabs min _ __________________________________12 psi (0,8 bar)
[psi(bar)]
1.2 20 (1.4)
pabs max ___________________________________73 psi (5 bar) 23 (1.6)
p
[rpm]
1.1
To determine the min. required inlet pressure pabs at inlet
port S or the reduction of displacement at higher input
0 max Speedn/n
abs
speeds see the diagram to the right.
Inletpressure
17.5 (1.2)
Outlet
1.0 14.5 (1.0)
Pressure at port B
Nominal pressure pN ___________________ 3600 psi (250 bar) 13 (0.9)
S to B.
Technical data
Table of values (theoretical values, without considering efficiencies and tolerances; values rounded)
Size A10V(S)O 10 18 28 45 63 85
Displacement V g max in
3 0.64 1.10 1.71 2.75 3.84 5.18
3 (10,5) (18) (28) (45) (63) (85)
(cm )
1)
Speed
g max 2)
max. at V n 0 max rpm 3600 3300 3000 2600 2600 2500
n rpm 4320 3960 3600 3120 3140 3000
max. at Vg < Vg max 0 max zul
Flow
at n q gpm 9.7 15.6 22 31 43 55
0 max V0 max
(L/min) (37) (59) (84) (117) (163) (212)
at n E =1500 min-1 q VE max gpm 4 7.1 11.1 18 25.1 34
(L/min) (15) (27) (42) (68) (95) (128)
Power Dp = 3600 psi
(250 bar)
at n P HP (kW) 22 (16) 34 (25) 47 (35) 65 (49) 90 (68) 119 (89)
0 max o max
at n E =1500 min-1 P E max HP (kW) 9.4 (7) 15 (11) 24 (18) 38 (28) 52 (39) 71 (53)
Torque
at Vg max Dp = 3600 psi T lb-ft 31 52 82 132 184 247
max
(250 bar) (Nm) (42) (71) (111) (179) (250) (338)
Dp = 1440 psi T lb-ft 13 21 33 53 74 102
(100 bar) (Nm) (17) (29) (45) (72) (100) (135)
Torsional stiffness Shaft S c lb-ft/rad 6760 8082 16400 27560 48100 105100
(Nm/rad) (9200) (11000) (22300) (37500) (65500) (143000)
Shaft R c lb-ft/rad – 10870 19400 30240 51200 –
(Nm/rad) – (14800) (26300) (41000) (69400) –
Shaft U c lb-ft/rad 5020 5870 – 22130 36290 75900
(Nm/rad) (6800) (8000) – (30000) (49200) (102900)
Shaft W c lb-ft/rad – – – 25370 39830 86960
(Nm/rad) – – – (34400) (54000) (117900)
Shaft K/C c lb-ft/rad 7965 – 19770 32380 54506 –
(Nm/rad) (10800) – (26800) (43900) (73900) –
Moment of inertia rotary group J TW 2 0.0142 0.2207 0.0403 0.0783 0.1329 0.2848
lbs-ft
2 (0,0006) (0,00093) (0,0017) (0,0033) (0,0056) (0,012)
(kgm )
3) a 2 8000 6800 5500 4000 3300 2700
Angular acceleration, max. rad/s
Fill volume V gal 0.05 0.06 0.08 0.13 0.21 0.26
(L) (0,2) (0,25) (0,3) (0,5) (0,8) (1)
Weight approx. (without fluid) m lbs (kg) 17 (8) 25 (11,5) 31 (14) 40 (18) 48.5 (22) 75 (34)
1) Values are valid with inlet pressure of 15 psi (1 bar) at suction inlet S. With reduced displacement or
increased inlet pressure the drive speed can be increased according to the diagram on page 5.
2) For higher drive speeds please consult us.
3) – These values are valid for conditions between the min. required and the max. permissible drive speeds.
For external sources of excitation (eg. diesel engine 2-8 fold rotary frequency, cardan shaft 2 fold rotary frequency).
– The limit is valid for a single pump.
– The load carrying capacity of the connecting parts must be taken into consideration.
Caution: Exceeding these limits can lead to a loss of operability, reduction of service life or complete destruction of the
axial piston unit. The permissible values can be calculated.
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
Technical Data
Determination of pump size
(at Vg max and Dp = 3600 psi (Nm) (42) (71) (111) (179) (250) (338)
1)
(250 bar ))
2)
Input torque, max.
for shaft end S T lb-ft (Nm) 93 (126) 91 (124) 146 (198) 235 (319) 465 (630) 851 (1157)
E zul
3) in 3/4 3/4 7/8 1 1 1/4 1 1/2
SAE J744
for shaft end R T lb-ft (Nm) – 110 (150) 166 (225) 295 (400) 479 (650) –
E zul
3) in – 3/4 7/8 1 1 1/4 –
SAE J744
for shaft end U T lb-ft (Nm) 44 (60) 43 (59) – 139 (188) 226 (306) 463 (628)
E zul
3) in 5/8 5/8 – 7/8 1 1 1/4
SAE J744
for shaft end W T lb-ft (Nm) – – – 162 (220) 292 (396) 447 (650)
E zul
3) in – – – 7/8 1 1 1/4
SAE J744
for shaft end K T lb-ft (Nm) 78 (106) – 107 (145) 156 (212) 325 (441) –
E zul
in 0.750 – 0.8750 1.0000 1.2500 –
(mm) (19.05) – (22.225) (25.4) (31.75) –
4) T E zul lb-ft (Nm) – – 107 (145) 156 (212) 325 (441) –
for shaft end C
Through drive torque, max.
for shaft end S T lb-ft (Nm) – 80 (108) 118 (160) 235 (319) 357 (484) 515 (698)
D zul
for shaft end R T lb-ft (Nm) – 89 (120) 130 (176) 270 (365) 357 (484) –
D zul
1) Distribution of torques T1 T2
without considering efficiency
2)
for shaft without side load
3)
(ANSI B92.1a-1996)
4) TE
only for series 52
1. Pumpe
2. Pumpe
1. Pump
TD
/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
qv
v
q
(80) (40) 60P
20 Pqv max
Flow
powe
r
gpm (L/min) (kW) HP 15 (60) (30) 40
10 30
PV q
10 (40) (20) 20Drive
7.5 (35) (20) 25 5 (20) Pqv min (10)
q
V
(25) p (15) 20 0 0
Flowq
Drivepower
5 qV max
(15) (10)
15
(50) (100) (150) (200) (250)(bar)
2.5 (5) (5) 10 0 1000 2000 3000 3625 psi
p
qV min 5
Operating pressure p
0
0 (50) (100) (150) (200) (250) (bar)
power P vq
(70)
Flow q v
30 (120) qv (60) 80
(80) (40) 60
(60) (40) 50
PV q
(30) 40
Drive
20 (60)
15 15 (20)
(50) (30) 40
V
qV
Flowq
Drivepower
10 (40)
10 (40) (20) 20 Pqv min 20
p 5 (20) (10)
(30) qV max p (10) 0
qV min 0
5 (20) (0) 0 (50) (100) (150) (200) (250) (bar)
0 (50) (100) (150) (200) (250) (bar) 0 1000 2000 3000 3625 psi
1000 2000 3000 3625 psi Operating pressure p
Operating presure p
Size 85
– – – – n = 1500 rpm n
Size 28 = 2500 rpm
– – – – n = 1500 rpm
gpm (L/min) (kW) HP
n = 3000 rpm 58 (220) (110) 146
55 (200) (100) 140
gpm (L/min) (kW) HP
23.8 (90) 50 (180) qV (90) 120
(40) 60
45 (160) (80)
20 (80)
40 100
qv
q v
v
(140) (70)
V
powerP
(10) 20power
35
qFlow
5 Pqv min
rive
0 25
D
0 p 60
qV max
t q
P pV max • 600 V theor
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. /44
DR - Pressure control
bar)
Static characteristic
(4
at n1 = 1500 rpm; tfluid = 120 °F (50 °C)
Adjustment erang
L
[gpm (L/min)]
Hy s te resisan
Operatin
Flow q V
setting range
g
(20)
290 min max
2 S
Ports
Dynamic characteristic
The curves show average measured values under test B Outlet port
condi-tions. S Inlet port
Conditions: n = 1500 rpm
L, L
1/2 Case drain port (L1/2 plugged)
tfluid = 120 °F (50 °C) Control data
Line main relief set at 4570 psi (315 bar)
Hysteresis and repeatability Dp max. 45 psi (3 bar)
Stepped loading by suddenly opening or closing the Pilot fluid consumption max. approx. 0.8 gpm (3
pressure line using a pressure relief valve at 3.3 ft (1 m)
L/min) Flow loss at qV max see page 8
downstream from the pump pressure outlet.
Control times
psi (bar)
4570 (315)
4350 (300) tSA [ms] tSA [ms] tSE [ms]
p
3620 (250)
Size against 725 psi against 3200 psi standby - 3600 psi
pressure
2175 (150)
10 70 50 15
1450 (100)
18 70 70 30
725 (50) 28 70 65 20
45 85 75 25
V 63 100 80 30
g max
85 120 100 40
Displacement(swivelangle)
V
g min
Control time
stroking time tSA de-stroking time tSE
10/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Control data
See page 9
L2 S
Ports
B Outlet port
S Inlet port
L, L1/2 Case drain ports (L1/2 plugged)
X Pilot pressure port
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 11/44
Dp
values
3625 (250)
V
see table of
Setting range
B
Operating press. p [bar]
L2 S
D
Flo
Vq
w
Speed n
(250) 3620
g75 (50 725
Loadpress ure
Displac eme ntV
(200 2900
50 (150 2170
25 (100) 1450
(18) 260
0
(stand by)
Control time
stroking time tSA de-stroking time tSE
Control times
tSA [ms] tSE [ms] tSE [ms]
Size stand by - 3600 psi 3600 psi (250 bar) 725 psi (50 bar)
(250 bar) - stand by - stand by
10 60 15 40
18 65 18 45
28 70 20 50
45 85 25 60
63 90 30 75
85 100 35 100
L, L1 Case drain ports (L1 plugged)
X Pilot pressure port
Differential pressure Dp
Standard setting: 200 psi (14 bar). If a different setting
is required please state in clear text.
When port X is unloaded to tank (and outlet B is closed) a
zero stroke pressure ("standby") of p = 260 ± 30 psi (18 ± 2
bar) results (depends on Dp-setting).
Control data
For pressure control see page 9.
Max. flow deviation (hysteresis and rise) measured at a
drive speed of n = 1500 rpm.
Size 10 18 28 45 63 85
Dqvmax 0.13 0.24 0.26 0.48 0.66 0.83
gpm
(0,5) (0,9) (1,0) (1,8) (2,5) (3,1)
(L/min)
Execution of pressure control like DR(G), see pages 9/10. When ordering please state the max. input torque in clear text.
Execution of pressure and flow control like DRS, see page 11.
Control data
In order to achieve a constant drive torque with varying
operating pressures, the swivel angle and with it the For technical data of pressure control see page 9.
output flow of the pump, is varied in such a manner, that
For technical data of pressure and flow control see page 11.
the product of flow and pressure remains constant.
Pilot fluid consumption max. approx. 0.8 gpm (3,0
Flow control is possible below the limit of the power curve.
L/min) Flow loss at qV max see page 8
4350 (300)
Pressure
3620 (250)
LA5
0 0
100 q
LA9 DqV (see table page 11)
T
Schematic: LAXDS
T[Nm]
LA8
X X
not included in
LA7
Torque
LA6
supply
L L1
B
LA5
Ports Flow qV [%]
0 100
B Outlet port
S Inlet port
L, L1 ,L2 Case drain ports (L1 ,L2 plugged)
L
X pilot pressure port 2
S
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 13/44
Notes
14/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
064. (103)
82-2 (A)
33..248250 DIA (Ø 82.55h8)
0
(9 . L
L1 )
35
DIA0.4 3(Ø 1 )
0.94 (24)
5.83 (148) 45°
Y
7.09 (180)
112. (53.5)2.(56)20
View Y right hand rotation
4.19 (106.4)
5.28 (134)
S B
1.13 1.13
(28.6) (28.6)
2.00 (51) 2.00 (51)
B S
1.13 1.13
(28.6) (28.6)
2.00 (51) 2.00 (51)
Shaft ends
S Spline shaft U Spline shaft K Parallel keye shaft 0.188 (4.76+0.025 )
1) 1) 0.187
3/4 in 11T 16/32DP 5/8 in 9T 16/32DP 0.01(2.5) 1.13
(28.6)
-0.1
)
0.833 121.+0.05
-0.02
ø3/4 in
3)
ø 5/8 in
Centering
0.827
DIA
(ø19.05
Ports
2)
Tightening torque, max.
B Outlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
S Inlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 9/16-18UNF-2B; 0.47 (12) deep 58 lb-ft (80 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2)see general information
3)axial retention of coupling half eg. with clamp coupling or with clamping screw
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 15/44
45° 5
43.
)
024. (102)
743. (95)
.
0
h
8 (9 3
0IAD11)(ø
)
ADI (ø55.82
°
Y 45
)
.
5)
L1
1.
.
250248.3.3
5.83 (148)
0.94 (24)
7.09 (180) 4.19 (106.4)
5.28 (134)
S B B S
1.13 1.13 1.13 1.13
(28.6)(28.6) (28.6)(28.6)
2.00 (51) 2.00 (51) 2.00 (51) 2.00 (51)
Ports
1)
Tightening torque, max.
B Outlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
S Inlet port ISO 11926 1 1/16-12UNF-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 9/16-18UNF-2B; 0.47 (12) deep 58 lb-ft (80 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; (11.5) deep 29 lb-ft (40 Nm)
1) see general information
16/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
3.27 (83)
0.31 (7.8) 0.39 (10)
0.96
(24.5) L1
Flange SAE J744 L1 L 0
4. (122)80
(72)
82-2 (A) .
)
L
1
(2
.
5
)
(11)
.5)
45°
2.83
h8
DIA (Ø82.55
430.
.42 (6 1
2 (6 .5)
Y .42
2.48 (63)
3.2503.248
45°
3.27 (83) L2
4.20 (106.4)
6.14 (156) 5.35 (136)
max. 7.20 (183)
View Y
port plate 61
312. (58.7)1.DIA(Ø32)26
0.79(Ø20)1.(47.6)87
S B
1.19 0.87
(30.2) (22.2)
Location of service ports for left hand rotation; turn port plate180° 1.26 1.10
(32) (28)
Shaft ends
S Spline shaft R Spline shaft U Spline shaft
1) 1) 1)
3/4 in 11T 16/32DP 3/4 in 11T 16/32DP 5/8 in 9T 16/32DP
(SAE J744 - 19-4 (A-B)) (SAE J744 - 19-4 (A-B)) (SAE J744 - 16-4 (A))
ø3/4 in 20UNC-2B
ø3/4 in
3)
ø 5/8 in
Centering
1/4-
Ports
2)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2)see general information
3)axial retention of coupling half, eg. with clamp coupling or with clamping screw
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 17/44
82-2 (A)
2
)
.
5
(11)
h8
(Ø32)312.(58.7)
.5)
45°
(Ø82.55DIA
1.DIA26
Y 1
0.43
42 (6 1
. (6 .5)
2 .42
3.2503.248
S 2
45°
L2
3.27 (83) 1.19 (30.2)
4.19 (106.4)
5.63 (143) 5.35 (136)
6.70 (170) 2.44 (62)
View Y X
port plate 62
4. (106)17
View Z
DIA(
Ø20)
Z
790. 871. (47.6)
Location of service ports for left hand rotation; turn port plate180°
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
18/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
8.86 (225)
4.45 (113)
3.27 (83)
0.31 (7.8) 0.39 (10)
0.96 (24.5)
L1
Flange SAE J744 L
(113) 804.
82-2 (A)
(72) 4.45
(122)
0 .
(2 1
.
33..248250 DIA (Ø82.55h8)
. 5
(11
45° )
2.83
)
5)
1
0.43
.42 (6 .5)
1
2 .42 (6
Y
2
2.48 (63)
45°
L2
134. (105)
312. (58.7)1.DIA(Ø32)26
0. (Ø20)79871.(47.6)
S B
1.19 0.87
(30.2) (22.2)
Location of service ports for left hand rotation; turn port plate180° 1.26 1.10
(32) (28)
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5 deep) 29 lb-ft (40 Nm)
1) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 19/44
8.86 (225)
4.45 (113)
3.27 (83)
0.31 (7.8) 0.39 (10)
0.96 (24.5)
L1
(122)(113)
L .
Flange SAE J744
82-2 (A) 0
(2 10
804.454.2.(72)83
43 0.(11 )
1
5)
.
45°
(Ø82.55h8)
5)
.
261.(Ø32)
Y 1
.42 (6 (6 .5)
2 .42
.250.248
2.(58.7)3 1
33DIA
2.48 (63)
2
45°
L2
S
3.27 (83) 1.19 (30.2) 4.19 (106.4)
5.63 (143) 5.35 (136)
6.69 (170) View Y 2.44 (62) X
Port plate 62
174. (106)
View Z
(Ø20)
87 6)1.(47.0.DIA79
B 0.87
(22.2)
S B
Location of service ports for left hand rotation; turn port plate180°
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread DIN 13 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1,2 Case drain ports (L1,2 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5 deep) 29 lb-ft (40 Nm)
1) see general information
20/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
3.54 (90)
864. (123.5)
h8
L
L 3)(14.
DIA (ø101.6)
0.56
)
Y 72 (69
.
2
2.87 (73)
2.60 (66)
43 .0000.9979
L1
876)
.1.7(4
S
B
S B 1.19 (30.2) 0.87 (22.2)
1.30 1.30
(33) (33) 1.30 1.30
Location of service ports for left hand rotation; turn port plate 180° (33) (33)
Shaft ends
S Spline shaft R Spline shaft K Parallel keyed shaft
1) 1)
7/8 in 13T 16/32DP 7/8 in 13T 16/32DP 0.251
0.10 1.13 (6.35 +0.025)
(SAE J744 - 22-4 (B)) (SAE J744 - 22-4 (B)) 0.25
(ø22.225 - )0,02
(2.5) (28.6)
0
ø7/8 in1/4-20UNC-2B
ø7/8 in1/4-20UNC-2B
0.97640.9843(25 -0.2 )
-2B
0.63
20UN
8750.08742
(16)
C
0.
ADI
1/4-
L/L1 Case drain ports (L1 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2)see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 21/44
4.86 (123.5)
X L
h8
550. (14.3)
)DIA(ø101.
1.26(ø32)312.
)
(58.7)
6
.5
(68
Y
70
.
2.(73)87602.(66)
4. 00003.9979
2.4107)(1
6)7.(4(ø20)
S B
Z
871.9.7
0
0.87 (22.2)
2.60 (66) 2.60 (66)
Location of service ports for left hand rotation; turn port plate 180°
Shaft ends
2)
C Tapered 0.75
DIA 0.749
(19.024)
(19) 0.87
(ISO 3019-1 - 22-3) 0.118 Section A-B
-2A
0.110 (22)
(3-0,2) 0.251(6.35+0.025)
(21.91)
DIA 0.863
18UNF
5/8-
A 0.250
2510.2500. 025(6.35+0.)
1(3.2+0.)
0.16 (4) B
006+0. )—0.006
85750.0.8570
0.1301260.
0.57
(14.4)
2.19 (55.6)
DIA
774(21.
Taper
125:1000
9.09 (231)
5.49 (139.5)
3.54 (90)
1.14 X
L1
L1
125.(130)764.(121)
0.37 (9.5)
X
0.25 (6.3) (29)
DIA0.56(ø14.3)
233.(82)
4)
0
Flange SAE .
12
J744 101-2(B) (3
L .91
)
45° L
DIA 4.0000 (ø101.6 )
h8
2 (7
W
2.59 (75)
45°
3.9979
.91 4)
2
(7
0
0.47 (12) (3 L2
.
12
3.54 (90) 6.69 (170) )
5.75 (146)
6.77 (172)
4.49 (114)
DIA 0.79(ø20)1.87(47.6)
2.31(58.7)DIA1.26(ø32)
S B
1.19 (30.2) 0.87 (22.2)
1.30 1.30
(33) (33)
Location of service ports for left hand rotation; turn port plate180°
Shaft ends see page 20,21
Ports 1)
Tightening torque, max.
9.09 (231)
5.49 (139.5)
3.54 (90)
125.(130)744.
0.37 (9.5) 1.14 X
L1
(120.5)
L1
)
(29)
0.25 (6.3)
X
DIA0.56(ø14.3)3.(82)23
2
Flange SAE J744
101-2(B) (3)
h8
L
L
4.0000 (ø101.
(ø32)
Z 45° .91
6
4)
3.9979
1.26
2.31(58.7)
(7
.91 4)
2.95 (75)
45°
2
(7
DIA
S 0
0.47 (12) 1.19 .
L2
12
(3
)
3.54 (90) (30.2) 5.75 (146)
6.30 (160)
6.77 (172)
7.36 (187)
View Y 2.48 X
port plate 62 (63)
right hand rotation
B494. (114)
View Z
1.87(47.6)DIA0.79(ø20)
B
S
V
2.60 (66) 2.60 (66)
0.87
(22.2)
Location of service ports for left hand rotation; turn port plate 180°
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 3/4in
Fixing thread ISO 68 3/8-16UNC-2B; 0.75 (19) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/4in
Fixing thread ISO 68 7/16-14UNC-2B; 0.79 (20) deep 48 lb-ft (66 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 3/4-16UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
24/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
3.90 (99)
0.37 (9.5) 0.47 (12)
0.25 (6.3) 1.18 (30)
45°
Flange SAE J744 L1
560. (14.3)
L
101-2 (B) L
h8
8)
DIA (ø101.6)
Y .07 (7
3
4.00003.9979
View Y View Y
port plate 64 port plate 61
right hand rotation right hand rotation
(69. 9
)
980.(ø25)
.7 5
(ø38)
501.
2 .0 6 . 4)
(52
S B S B
1.50 1.50 1. 1.
03
(35 41
(38) (38)
. 30 ° 2) 30° (26.
Location of service ports for left hand rotation; turn port plate 180° 7) 1.50 1.50
(38) (38)
Shaft ends
S Spline shaft R Spline shaft U Spline shaft W Spline shaft
1) 1) 1) 1)
1 in 15T 16/32DP 1in 15T 16/32DP 7/8 in 13T 16/32DP 7/8 in 13T 16/32DP
(SAE J744 - 25-4 (B-B)) (SAE J744 - 25-4 (B-B)) (SAE J744 - 22-4 (B)) (SAE J744 - 22-4 (B))
ø7/8in1/4-20UNC-2B
ø7/8in1/4-20UNC-2B
ø1in1/4-20UNC-2B
20UNC-2B
ø1in
1/4-
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2)see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 25/44
(131.5)
L1
S
(77)
5.18
L
h8
(ø101.6 )
752.(69.9)
1.50(ø38)
78
Y
.0000.9979
43DIA
534. (115)
View Z
Shaft ends
2)
K Shaft C Tapered shaft (ISO 3019-1 - 25-3)
B
84(21.41)0.
0.250(6.35
2(28. 0,2
-
025(6.35+0.)
1(3.2+0.)
(25.4)16UNF-
DIA 1in
-
.1.0 80000998
(16)
11021.10241.
1/4-20UNC
ADI
0.63
99(25.16)0.
3/4-
B
2510.2500.
0.1301260.
9.25 (235)
5.75 (146)
3.90 (99)
Flange 0.37 (9.5) 1.22 (31)
L1
0.25 (6.3)
SAE J744 L
101-2 (B)
0
(83)
245. (133)
844. (123)
)
.
12
(3
(14.3)
)
h8
273.
(Ø101.6
45°
(7
560.
.5) 7)
Y .03
5
4.00003.9979 DIA
.97 (7 3
45°
623. (92)
2
0.47 (12)
0
L2 .
12
(ø25)
4. (116)57
)
(69 .9
75
(ø38IAD501. )
.
2
98.0
2 .0 6 . 4)
(52
S B
1. 1.
(35 41 30°
.7) 30° (26 03
.2)
1.50 1.50
(38) (38)
Location of service ports for left hand rotation; turn port plate 180°
Shaft ends see page 24, 25
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 1 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 27/44
9.25 (235)
5.75 (146)
3.90 (99)
0.37 (9.5) 1.22 (31)
L1
Flange 0.25 (6.3) L1
X L
SAE J744
0
245. (133)
101-2 (B) S
4.84 (123)
.
08
DIA (Ø101.6 h8 )
273. (83)
(2
.0000
1.50(Ø38)2.(69.9)75
)
.9979
314.
.5) 7)
45°
.03(7
Y 5
623. (92)
.97 (7 3
43
2
45°
0
0.47 (12) 1.41 L2 .
12
(3)
3.90 (99) (35.7) 5.75 (146)
7.00 (178) 6.77 (172)
8.31 (211)
X Pilot pressure port ISO 11926
1) see general information
View Z
0.98 (ø25) 062. 4)(52.
1.03
(26.2)
4. (116)57
S
Tightening
1)
torque, max.
1in
3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
1 1/2in
1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
7/8-14UNF-2B 174 lb-ft (240
Nm)
7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40
Nm)
28/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
5.39 (137)
45°
L
1
Flange SAE J744 L1
S L
101-2 (B)
(87)
L .5)
34..99790000 DIA (ø101.6h8)
(ø50)
3
5.75 (146)
View Z
2. (52.064)0.
(ø25)98
S B Z
B 1.11
(26.2)
Location of service ports for left hand rotation; turn port plate 180° 2.83 (72) 2.83 (72)
Shaft ends
S Spline shaft R Spline shaft U Spline shaft W Spline shaft
1) 1) 1) 1)
1 1/4 in 14T 12/24DP 1 1/4 in 14T 12/24DP 1 in 15T 16/32DP 1 in 15T 16/32DP
(SAE J744 - 32-4 (C)) (SAE J744 - 32-4 (C)) (SAE J744 - 25-4 (B-B)) (SAE J744 - 25-4 (B-B))
18UNC-2B
-2B
ø1 in1/4-20UNC-2B
ø1 in1/4-20UNC-2B
in
5/16-18UNC
ø1 1/4 in
Ports
2)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2)see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 29/44
5.93 (137)
127-4 (C) (1 4
.
.
56
)
L 3)
33.4 (87)
(114.5)
DIA(ø127 h8
)
.5
8
Y 09 (7
3.
4.51(76)
5.00004.9975
835. (148)
2.99
8.19 (208) 4.51 (114.5)
5.75 (146)
2.56 (65) X
View Y
(120.5)74
port plate 61
4.
right hand rotation
063. (77.8)1.(ø50)97
980.(ø25)
2.06 (52.4)
S B
1.67 (42.9)
1.03 (26.2)
1.30 (33) 1.81 (46)
Location of service ports for left hand rotation; turn port plate 180°
Shaft ends
K Parallel keyed shaft 2)
C Tapered (ISO 3019-1 - 25-3)
0.3136
(7.94+0,025) 0.13 1.16 Section A-B
1.63 0.3126 (3.2) (28.6)
+0.025(7.94)
—0.1
840.
41)(21.
0.12 B
3/4-16UNF-2B
(41.3)
ADI 2501.082481 (¿31.75 )0,03
A 0.3126
(25.16) (25.4)
0.13940.1354) (3.54
DIA1.25(31.75)0.3136
DIA1.0715
B-2
Taper0.3126
0.99
0.56 (30)
-
5/16-18UNC
0.75
(19)
.
0.12
(14.1) (3)
1.18
0.31 (7.9) 0.93 1.37 125:1000
2.18 (55.4)
(23.6) (34.9)
2.61 (66.4)
Ports
1)
Tightening torques, max.
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) 2)
see general information only series 52
30/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
9.72 (247)
5.93 (150.5) Mounting flange „D“
55
4.55 (115.5) L1
0.5 (12.7) 1.54 (39) L1
6.3 X
Flange SAE J744
L
. 4)
0
5.515.04 (140)(128)
(1
127-4 (C)
50(88)3. (89)
43
DIA (ø127h8 )
45°
514.(114.5)
5.(146)75
45°
(7 9)
45°
Y .5) 11
.
7
3
.05 (7
5.00004.9975
463.
0.59 (15) 4.55 (115.5) L2
4.51 (114.5)
8.19 (208) 5.91 (150)
View Y 2.56 (65) X
port plate 61
right hand rotation
3. (77.8)06971.(ø50)
062. (52.4)4.(124)88
0. (ø25)98
S B
Ports 1)
Tightening torque, max.
9.72 (247)
5.91 (150) Mounting flange „C“
4.55 (115.5)
X
0.37 (9.5) 1.54 (39) L1 L
0.25 (6.3) 1
Flange SAE J744 9)
L
5.51 (140)
5.04 (128)
101-2 (B) L
0.(14.3)563.(89)50
43°
h8
(ø101.6)
11
.
(77.8)
(ø50)
Y 3 (7
4.00003.9979 DIA
.05 5)
1.97063.
3
.
45°
(88)46
(77
3.
S
0.59 (15) 1.69
L2
4.55 (115.5) (42.9) 5.75 (146)
7.93 (201.5)
6.77 (172)
9.43 (239.5)
(124)
4.8
View Z
8
S
B
Z
2. (52.4)06
0. (ø25)98
B
1.03 (26.2)
Location of service ports for left hand rotation; turn port plate 180°
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 61) SAE J518c 1in
Fixing thread ISO 68 3/8-16UNC-2B; 0.71 (18) deep 31 lb-ft (42 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2in
Fixing thread ISO 68 1/2-13UNC-2B; 0.87 (22) deep 65 lb-ft (90 Nm)
L/L1 Case drain ports (L1 plugged) ISO 11926 7/8-14UNF-2B 174 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
32/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
126. (155.5)
L1
127-2 (C) L )
L
)
(17.5)(93.5)
h
8
5.00004.9975 (ø127DIA
690.
3.68
4 (95
Y .7
3
(88)3.46
9.65 (245)
6.22 (158)
7.13 (181)
8.26 (210)
View Y
port plate 61 right
hand rotation
32ø66.7
3. (88.9)502.(3660)ø
S B
1.97 1.77
(50) (45)
Location of service ports for left hand rotation; turn port plate 180° 2.00 (50.8) 1.25 (31.8)
3.62 (92) 3.11 (79)
Shaft ends
S Spline shaft U Spline shaft W Spline shaft
1) 1) 1)
1 1/2 in 17T 12/24DP 1 1/4 in 14T 12/24DP 1 1/4 in 14T 12/24DP
(SAE J744 - 38-4 (C-C)) (SAE J744 - 32-4 (C)) (SAE J744 - 32-4 (C))
ø1 1/4 in5/16-18UNC-2B
ø1 1/4 in5/16-18UNC-2B
-2B
7/16-14UNC
ø1 1/2 in
Ports
2)
Tightening torque, max.
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90) Nm
L/L1 Case drain ports (L1 plugged) ISO 11926 1 1/16-12UN-2B 260 lb-ft (360 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat root, side fit, tolerance class 5
2)see general information
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 33/44
(17.5)
6.(155.5)12
(93.5)
L1
127-2 (C)
)
L L
690.
683.
)
h8
(ø127
59)3.(88.
362.DIA(ø60)
5 (95
Y
0000.997 .
5
.7
54 DIA
463. (88)
2.00
6.22 (158)
9.27 (235.5) (50.8) 7.13 (181)
10.90 (276.8) 8.27 (210)
View Y 2.91 (74)
0.45 (11.5)
port plate 62 X
right hand rotation
5. (139)47
View Z
B
1.26 (ø32) 2.63 (66.7)
S B Z
1.25
(31.8)
Location of service ports for left hand rotation; turn port plate 180°
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90) Nm
L/L1 Case drain ports (L1 plugged) ISO 11926 1 1/16-12UN-2B 260 lb-ft (360 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B 0.45 (11,5) deep 29 lb-ft (40) Nm
1) see general information
34/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
10.75 (273)
7.15 (181.5)
5.63 (143)
0.50 (12.7) 1.42 (36) X
L1
0.40 (10.2)
L1
X
0
915. (150)
FlangeSAE J744
5.71 (145)
127-2 (C) L
.
16
(101)
(4
h8
)
(ø127)
983.
Y 45° L
74 )
.
3 (95
5.00004.9975 DIA
044.(102.5)
74 )
690.(17.5)
. 45
3 (95
°
0 L
0.79 (20) (416. 2
5.12 (130) )
7.13 (181)
9.65 (245)
8.27 (210)
View Y 2.91 (74) X
port plate 61
261. (ø32)2.(66.7)63245.(133)
right hand rotation
(88.9)(ø60)
503.2.36
S B
2.00
Ports 1)
Tightening torque, max.
10.75 (273)
7.15 (181.5)
5.63 (143)
0.50 (12.7) 1.42 L1
L1 X
(150)
(145)
0.40 (10.2) (36) X 0
Flange SAE J744
127-2 (C) L
.
16
L (4
)
915.
5.71
(101)
45°
h
8
DIA (ø12
7
2.48 (ø63)
503. (88.9)
.
74
983.
3 (95)
Y
.
00005.99754.
74
0.(17.5)69
3 (95)
044.(102.5)
45°
S
0
0.79 (20) 2.00 .
16
L2
(4)
5.12 (130) (50.8) 7.13 (181)
9.27 (235.5) 8.27 (210)
10.91 (277)
View Y 2.91 (74)
X
port plate 62
right hand roation
5. (133)24
(ø32)
View Z
63 7)2.(66.1.DIA26
B
S
Z
B
1.25 (31.8)
Location of service ports for left hand rotation; turn port plate 180°
Ports
1)
Tightening torque, max.
B Outlet port, SAE flange (code 62) SAE J518c 1 1/4in
Fixing thread ISO 68 1/2-13UNC-2B; 0.75 (19) deep 65 lb-ft (90 Nm)
S Inlet port, SAE flange (code 61) SAE J518c 2 1/2in
Fixing thread ISO 68 1/2-13UNC-2B; 1.07 (27) deep 65 lb-ft (90 Nm)
L/L1/2 Case drain ports (L1/2 plugged) ISO 11926 1 1/16-12UN-2B 360 Nm
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.45 (11.5) deep 29 lb-ft (40 Nm)
1) see general information
36/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
12 (102)
l1 l2
DIA
)
+0.050+0.020
A B
63 10.04 0.37 2.32 M10; 0.63
(ø82.55
3.25203.2508
4.19
(106.5) (255) (9.5) (59) (16) deep
85 11.89 0.53 2.68 M10; 0.63
0.39 (10) (302) (13.4) (68) (16) deep
A5
+0.050020+0
A2
to pump mounting face A1
K68 Flange SAE J744 - 101-2 (B) 1)
7/8 in 13T 16/32 DP
Coupler for splined shaft to ANSI B92.1a-1996 (SAE J744 - 22-4 (B))
Section A-B Size A1 A2 A3 A4 A5
A4
not on size 28 and 45 28 8.03 1.66 0.7 1.85 M12; 0.71
A3
(204) (42.3) (17.8) (47) (18) deep
45° 45 9.02 1.67 0.7 2.09 M12; 0.71
A B
)
DIA
(ø101.
6
(1 75
(255) (42.4) (17.9) (59) (18) deep
46) 85 11.89 1.83 0.87 2.71 M12; 0.79
A5 (302) (46.5) (22) (69) (20) deep
not on size 28 and 45 0.39 (10)
A2
to pump mounting face A1
1) 30° pressure angle, flat root, side fit, tolerance class 5
38/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
)
B
A
DIA
+0.020
+0.050
85 11.89 2.01 0.87 2.71 M12; 0.79
(ø101.
5. (302) (51.2) (22.2) (69) (20) deep
6
75
(1
ø101.6ø101.6
46)
notn onavecsizecal45.45 0.39 (10)
A5
A2
jusqu‘au flasque de montage
to pump mounting face A1
(ø127
Coupler for splined shaft to ANSI B92.1a-1996 (SAE J744 - 32-4 (C))
Section A-B Size A1 A2 A3 A4 A5
Coupe A-B
45° A4
85 11.89 2.36 0.88 2.67 M16; 0.94
A
A3 (302) (59.9) (22.4) (67.9) (24) deep
)
DIA
+0.050+0.020
.13 )
7
81
(ø1
00205.00085
(ø127
A5
.
B
0.51 (13)
to pumpjusqu‘aumountingflasqueface deA montage
1
DIA
)
81
050+0.020+0
.
.13 )
7
5.002000085.
(ø127
(ø1
A5
B
0.51 (13)
to pjusqu‘aumpmountingflasquefacede montageA1
Installation notes r • l • dv 3
r = density [kg/m ]
Optional installation position. The pump housing must be Dp = -5 l = pipe lenght [m]
1
dt • 10 [bar]
filled with fluid during commissioning and operation. dv/dt = change of fluid velocity inlet
In order to obtain a low noise level, all connections (inlet, [m/s2] Dp2: Pressure loss due to static head
outlet, pilot pressure and case drain lines) must be linked Dp 2 = h • r • g • 10-5 h = height [m]
by flexible members to tank. [bar]
Avoid placing a check valve in the case drain line. 3
r = density [kg/m ]
2
The highest of the case drain ports (L; L1 or L2) must be g = gravity acceleration = 9,81 m/s
con-nected to tank with piping material for standard Dp3 = Line losses (elbows etc.)
pressure rating suitable for the port sizes.
Horizontal installation
Vertical installation (Shaft end upwards)
The pump must be installed in such a manner, that either
Arrangement inside the reservoir "L", "L1"or "L2" is at the top.
Before installation fill pump housing, keeping it in a Arrangement inside the reservoir
horizontal position.
a) If the min. fluid level is equal to or above the pump mounting a) If the min. fluid level is above the top of the pump: plug
face: plug port "L" , "L1" and "S" open; it is recommended to port "L1" , "L" and "S" open; it is recommended to pipe "L“
and connect a suction pipe to "S“ (see fig. 3).
pipe "L1" and connect a suction pipe to "S" (see fig. 1).
b) If the min. fluid level is below the pump mounting face: b) If the min. fluid level is below the top of the pump: pipe
pipe ports "L1" and „S" acc. to fig. 2 "L" plugged. (see also "L" and "S" acc. to fig. 4, "L1" plugged (see also limit of
limit of conditions) condi-tions).
Note: to avoid pump damage, remove all protective parts Note: to avoid pump damage, remove all protective parts
(dust covers, plastic plugs etc.) before installation. (dust covers, plastic plugs, etc) before installation.
Fluid
min. 7.87 in (200 mm)
L1 Fluid
L
L S min
min. 7.87 in S
ht
L1 Fig. 3
(200 mm) Fig. 1
Arrangement outside the reservoir
Baffle
Fig. 2
Baffle
Overall pressure loss
h
Notes
42/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
Notes
RA 92 703/11.07 | A10VO Mobile Hydraulics | Bosch Rexroth Corp. 43/44
Notes
44/44 Bosch Rexroth Corp. | Mobile Hydraulics A10VO | RA 92 703/11.07
General information
– The A10VO pump is designed to be used in open circuits.
– Project planning, assembly and commissioning of the pump require the involvement of qualified personnel.
– The service line ports and function ports are only designed to accommodate hydraulic lines.
– During and shortly after operation, there is a risk of burns on the pump and especially on the solenoids. Take suitable
safety precautions, e.g. wear protective clothing
– There may be shifts in the characteristic depending on the operating state of the pump (operating pressure, fluid temperature).
– Tightening torques:
- The tightening torques specified in this data sheet are maximum values and must not be
exceeded (maximum values for screw thread).
Manufacturer´s instruction for the max. permissible tightening torques of the used fittings must be observed!
- For DIN 13 fixing screws, we recommend checking the tightening torque individually according to VDI 2230 Edition 2003.
Bosch Rexroth Corporation Bosch Rexroth Corporation © This document, as well as the data, specifications and other information
Mobile Hydraulics Industrial Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not
Axial & Radial Piston Units 2315 City Line Road be repro-duced or given to third parties without its consent.
8 Southchase Court Bethlehem, PA 18017-2131 The data specified above only serve to describe the product. No statements
Fountain Inn, SC 29644-9018 USA concerning a certain condition or suitability for a certain application can be de-
USA Telephone (610) 694-8300 rived from our information. The information given does not release the user from
the obligation of own judgment and verification. It must be remembered that our
Telephone (864) 967-2777 Facsimile (610) 694-8467
products are subject to a natural process of wear and aging.
Facsimile (864) 967-8900 www.boschrexroth-us.com
www.boschrexroth-us.com Subject to change.