Professional Documents
Culture Documents
Ingles
Ingles
circulates through many pieces of equipment, including the mud pump, the
discharge line, the standpipe, the rotary hose, the swivel, the kelly (or the top
drive), the drill pipe, the drill collars, the drill bit, the annulus, the return line, the
shale shaker, the desilter, the desander, the mud pits, and the suction line
The mud pump draws in mud through a suction line from the mud pits, or tanks,
and sends it out a discharge line. From the
discharge line, the mud goes into the
standpipe. The standpipe runs vertically up one leg
of the derrick. Mud exits the standpipe into a
strong, flexible, and reinforced rubber hose
called the rotary hose, or kelly hose. The rotary
hose joins the swivel at the gooseneck. The
mud then flows down the kelly (or through the top
drive), drill pipe, and duill collars. It jets out of the
bit nozzles and moves cuttings away from the bit. The mud and cuttings then
head up the hole in the annulus. The annulus, or annular space, is the area be-
tween the drill string and the wall of the hole. The mud leaves the annulus
through a steel pipe called the mudreturn line. It falls over a vibrating screen,
the shale shaker. The shaker screens out the larger cuttings and, in some
cases, dumps them into the reserve pit.
Offshore and in environmentally sensitive
areas, however, the shaker dumps the
cuttings into a receptacle. Later, the
contractor removes the receptacle, washes
the cuttings if required, and properly dis
poses of them. In either case, the clean
mud drains back int the mud tanks. The
pump then recycles it back down the hole
The mud pump recirculates the mud over and over through- out the drilling of
the well. From time to time, the derrickhand adds water, clay, and other
materials to make up for downhole losses. This crew member also adjusts the
mud's properties as the borehole encounters new and different formations.
Auxiliary Equipment
Several pieces of auxiliary equipment keep the
mud in good shape. The shale shaker sifts out
the normal-sized cuttings Sometimes, though,
the bit creates particles so small that they fall
through the shaker. Desilters and desanders
remove fine particles, or small solids, to keep
them from contaminating the drilling mud.
Conclusion
The circulating system of a drilling rig is one of the most important aspects of a drilling
rig. Without the components that make up the circulating system it could not fulfill its
main duty of removing the rock cuttings from a drilled well.
Traducción
Equipos de circulación de barro
circula a través de muchas piezas de equipamiento como ser : the mud pump,
the discharge line, the standpipe, the rotary hose, the swivel, the kelly (or the
top drive), the drill pipe, the drill collars, the drill bit, the annulus, the return line,
the shale shaker, the desilter, the desander, the mud pits, and the suction line
La bomba de lodo atrae el lodo a través de una línea de succión desde los pozos de
foso o tanques, y lo envía a la línea de descarga. Desde la línea de descarga, el lodo
entra en el tubo vertical. El tubo vertical corre verticalmente hacia arriba de una pata
de la torre de perforación. El lodo sale del tubo vertical hacia una manguera de goma
fuerte, flexible y reforzada llamada manguera rotativa o manguera de Kelly. La
manguera giratoria se une al eslabón giratorio en el cuello de cisne. El lodo luego
fluye hacia abajo por Kelly (oa través de la unidad superior), la tubería de perforación y
los collares de duill. Sale de las boquillas de la broca y aleja los recortes de la broca.
El barro y los recortes luego encabezan el agujero en el anillo. El anillo, o espacio
anular, es el área entre la sarta de perforación y la pared del orificio. El lodo abandona
el anillo a través de un tubo de acero llamado la línea mudreturn. Cae sobre una
pantalla vibratoria, el shale shaker. El agitador corta los cortes más grandes y, en
algunos casos, los arroja al pozo de reserva. Sin embargo, en la costa y en áreas
ambientalmente sensibles, el agitador vierte los recortes en un receptáculo. Más
tarde, el contratista retira el recipiente, tritura los recortes si es necesario y los desecha
correctamente. En cualquier caso, el lodo limpio drena los depósitos de lodo. La
bomba luego lo recicla por el agujero
La bomba de lodo recircula el lodo una y otra vez a través de la perforación del pozo.
De vez en cuando, el derrickhand agrega agua, arcilla y otros materiales para
compensar las pérdidas en el pozo. Este miembro de la tripulación también ajusta las
propiedades del lodo a medida que el pozo se encuentra con formaciones nuevas y
diferentes.
Equipo auxiliar
Varios equipos auxiliares mantienen el barro en buena forma. La coctelera de
esquisto tamiza los recortes de tamaño normal A veces, sin embargo, la broca crea
partículas tan pequeñas que caen a través de la coctelera. Los desilters y los
desanderers eliminan partículas finas, o sólidos pequeños, para evitar que contaminen
el lodo de perforación.