Professional Documents
Culture Documents
CONTENTS
Chapter One Danger,warning and caution items........................................ 7
Safety instruction............................................................................................ 7
1.1 Installation condition and power supply................................................ 8
1.2 Catution items for installation................................................................9
1.2.1. Installation of waterproof connector. ................... .................. ...11
1.2.2. Weighing unit.................................... .................. ................11
1.3 Caution items when running................................................................ 11
1.4 Basic caution items.............................................................................. 12
1.5 Caution items for maintaining..............................................................12
-2-
Chapter Seven Weighing of puffy food.................................................... 67
7.1. Characteristic of puffy food................................................................... 67
7.2. Controlling of material...........................................................................67
7.3. Adjustment of parameter........................................................................ 67
-3-
Preface
-4-
Main Parts Construction
8 7
6
9 5
10
11 4
12
3
13
2
14 1
-5-
Introduction of Combination Principle
The machine’s CPU will process the weight data received from each weigh hopper,
and calculate out numerous qualified combinations which comply with the target
weight, and then choose the closest one to discharge.
36.0
8 15
.0 .0
18 9
7
24.0
11.0
10
6
26.1
25.1
5
0. 4 2 3
32 8
3 5.
9.32
-6-
Chapter One Danger, warning and caution items
Safety instruction
In this operating manual your will learn a variety of icons on the left side such as
danger, warning, importance, caution, etc. Please read the following items carefully to
ensure that the equipment can be operated safely and correctly.
The standardization of the equipment operation is the product of every technician’s
efforts. Please read and learn the signs with commitments.
The danger mark means the danger may cause extensive harmful
consequence, might even result in casualty accident. In order to
prevent this accident, we must strictly follow the operating rules.
The important mark means how to prevent the equipment problem in order to
extend the life expectancy of the machine and use the machine to best.
7
1.1 Installation condition and power supply
Please pay attention to installation condition.
The equipment installation condition should be firm enough to
support this equipment and related equipments, we also need to
consider illumination for daily operating and after sale service .
Please don’t put the multihead weigher into the inflammable and
explosive working environment. This equipment is not
flame-proof.
Power supply
AC220V(within ±10% fluctuation)single phase 50/60 HZ,power
2 KW.
Machine carrying
Please pay great attention to the equipment carrying. You can see
the weight of machines on the manual, please use designated rings
when lift the machines.
8
1.2 Caution items for installation
Environment condition
The installation place must be rigid and without shaking, the working
environment should be without wind, because these factors will effect
the weighing accuracy.
9
Ground wire connecting
To protect the safety of operator and equipment and enhance the
anti-disturb ability, each of the equipments should be connected with
ground wire separately. Shown as following;
10
1.2.1. Installation of waterproof connector
11
1.4 Basic caution items
Caution items of touch screen operation
During operating, it is suggested only the finger abdomen should be
used to touch the screen. Don’t touch the screen by using fingernail,
pencil or other shaping tools ,because it will damage the touch screen
surface.
Please make sure all electric fixing is in good condition, and the machine
cover is fully sealed before turning on.
When connecting with packaging machine, you can turn on the machine
and enter into the manual or automatic operation only after making sure
no other people are around.
Operator should wear suitable uniform, do not wear loose uniform, tie,
decoration or keep long hair. To avoid damage, it is not allowed to touch
the roller or bearing.
You can change the spare parts only 5 minutes later after cutting off
the power supply.
12
Chapter Two System Setup
Firstly user should set up the parameters according to whole packaging system. Please
refer to page 21 to enter this menu.
2.1.Timing HP mode
Tm HP Mode
1.Tm Mode:There are four modes for Tm HP (0-3).Please see the figure on the below:
Tm HP Mode 0:No Timing hopper.
13
Tm HP Mode 1:Two Timing HP doors open at the same time (one packaging
machine).
14
Tm HP Mode 3 : Single timing hopper motor + unqualified weight rejection
( qualified weight dumped into packaging machine, unqualified
weight dumped into recycling bag ).
15
The way of selecting of correct connecting mode: when packaging machine is ready
and no ‘ discharge request ’ signal output, we should use multihead weigher as
master. If it output ‘ discharge request ’ , use packaging machine as master. If
multihead weigher connects with pouch giving machine, use open control.
After selecting connecting mode, please do as follows:
Number 1, Multihead weigher as master: When the combination and weigh is ready,
send firstly the “ready for combination” signal. After receiving the “ready for
combination” signal, the packaging machine immediately send to the combination
weigher “discharge request” and begin to pack after some delay
Connecting methods: The signal connection wire of back equipment has elicited
discharged signal 1 (P061A、P061B,Welding in KJ1 1,2 feet),when using ready
signal, please choose P063A、P063B(Welding in KJ1 3,4 feet)。
Number 2, Packaging machine as master : Packaging machine will firstly send
“discharge request” to the combination weigher and wait for the material dumped
from the combination weigher. After dumping material to the packaging machine,
combination weigher delays some time (can be adjustable) and then feedbacks the
“discharged” signal. Then the packaging machine begins to pack.
Connecting methods: The signal wire of back equipment connects discharged
signal 1(P061A、P061B)and discharge request signal 1(P068A、P068B)directly.
Number 3, Open control: Each time the packaging machine finishes a procedure, it
sends to the combination weigher a “discharge request” within its working circle
time.
Connecting methods: The signal wire of back equipment only needs to connect the
discharge request signal 1(P068A、P068B).
Because there are many ‘discharge request’ signals for packaging machine, in order
to ensure the system work correctly, we add some discharge signal accordingly, such
as: Pulse with memory, Tension without memory, Tension with memory, Pulse
without memory. We will introduce the setup skills of choosing signal detection
modes in four steps: Analysis, Setup, Solution, and Judgment (refer to the above chart)
16
as following:
17
and packaging machine stop outputting signal, the whole packaging system will be on
pause status).
Judgment:If packaging machine work first and multihead weigher can’t work, the
signal packaging machine output must be as wave 1; if multihead weigher work first
and sometimes the system will be on pause status (multihead weigher don’t memorize
the signal),and the system work again after short-circuit discharged signal cable,
please use the with memory in this situation;you also can judge it by PLC indicator
light.
18
Chapter Three Preliminary Commissioning
You should operate the touch screen with your finger abdomen, do not use
fingernail, pencil and other sharp objects, it will damage the surface of
touch screen and result in other relating issues.
19
After 5 seconds, if the combination weigher 'tick' one time, it means the zeroing
operation is OK. Meanwhile the word “zeroing” will disappear, and will display the
current Beijing time (If foreign customers need to show local time, they can enter the
System Setup to modify time).
Records
It will display production records when
you touch ‘records’ icon.
Calibration
20
only. Press ‘calibration’ and a
secondary password (‘282828’ ) is
required, operators will be only
allowed to this function by entering
correct password.
System Setup
System setup menu is for trained operator
only. Press ‘system setup’ and a secondary
password (‘282828’ ) is required, operators
will be only allowed to this function by
entering correct password.
Program Setup
21
will be only allowed to this function by entering correct
password.
22
3.3 Test for functional
parts
Press ‘manual test’ to enter this function.
23
Linear vibrator test
Press the number key to select one particular
linear vibrator for testing, “0” means all of
the linear vibrators. Take number 2 linear
vibrator for example: input ‘2’ and press
linear VB, then number 2 linear VB will
vibrate for one time accordingly.
24
Timing hopper test
Input ‘0 or 1 or 2’which stands for the timing hopper numbers, “0”stands for two
timing hoppers. Take number 2 timing hopper for example: input 2 and then press
Timing hopper, the number 2 timing hopper will operate for one time. Ensure the two
timing hoppers can work correspondly.
25
Load Cell Test
Input ‘0’(stands for all load cells) and then press Load Cell, it will display the current
value of each load cell.
If current value is more than 0.2g, please press ‘zero’ and make weigh hopper work
for several times, please make sure the value of each load cell is within ±0.2g .
System Test
Attention:Provided all the preparation work are properly done.
When multihead weigher and packaging machine is ready, please press ‘test’, and the
system will work in simulative mode.
If all the tests turn out to be fine, it means the fundamental function of
displayer, multihead weigher and packaging machine is in good
condition.
26
Chapter Four Basic parameter setup
Skills:
4.
1.Parameter
.Parameter selection
Take 10 head weigher (Pasta; target weight:55g) as an example:
First:parameter copy, 13 default settings of parameters is pre-set aiming at nut
fruit (Length is within 4 cm; including bean, peanut and pasta etc) and matching
parameter NO and target weight.
27
Program Setup 1
Program No 1 2 3 4 5 6 7 8 9 10 11 12 13
Preset Sp 65 63 60 57 55 53 50 48 46 44 40 44 40
Target Wt 50 100 150 200 250 300 350 400 450 500 800 1000 2000
Over Wt 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2
Under Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Main AMP 40 45 47 50 55 55 57 59 61 62 66 62 66
Lin AMP 36 43 45 47 49 50 52 55 56 57 60 57 60
VB Feed Tm 20 22 24 26 30 32 34 40 40 45 50 40 45
Lin VB Delay 19 20 22 24 28 29 30 31 32 33 35 34 36
Feed HP Dly 19 20 22 24 28 29 30 30 32 33 35 34 36
Weigh HP Dly 0 0 0 0 0 0 0 0 0 0 0 0 0
Time HP Dly 50 50 50 50 52 54 55 57 58 60 61 60 61
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 10 10 10 10 10 10 10 10 10 10 10 10 10
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 72 74 76 78 80 82 84 86 88 90 100 90 95
Multicomb 1 1 1 1 1 1 1 1 1 1 1 2 3
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500 500 500 500
Program Setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4.2 4.3 4.4 4.4 4.4 4.5 4.5 4.5 4.6 5 5 5
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24 25 25
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 2 2 2 2 3 3 5 3 5
WG HP Opn Tm 1 1 1 1 2 2 2 2 3 3 5 3 5
Time HP Dly 1 1 1 1 2 2 2 2 3 3 5 3 5
FD HP Motor 2 2 2 2 2 1 1 1 1 1 0 1 0
WG HP Motor 2 2 2 2 2 1 1 1 1 1 0 1 0
TM HP Motor 2 2 2 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1 1 1
Level Feed T. 10 10 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Notes:
1/.Some original parameters may be different due to program updating.
1/.
28
2/. It is mainly used when timing HP mode:0.
3/. This set of parameter table is mainly set for the nut material.
For example , if we want to weigh nut products with target weight 55g,select the
program No. that has target weight close to 55g and then copy to another program
No.(more than 13).From the above parameter form we know the number 1 is most
suitable, copy it to Program No 20.
29
Thirdly, Set up target weight, as picture shown below:
Fourthly, Set up preset speed, over weight, under weight and correct weight.
Notes:Preset speed of multihead weigher should be faster than system requirement by
2-3 bags/min.
Generally the correct WT is set as 0.
elay//Linear Vibrator feed delay:: It refers to delay how much time for
1. Lin VB Delay
linear vibrator to feed products into the feed hopper after opening the feed hopper.
unit is10ms.
2. Feed HP Dly ly//Feed hopper delay: It refers to delay how much time for the feed
hopper to feed products into the weigh hopper after opening the weigh hopper. Unit is
10ms.
TM/Sample stable Time: After opening the feed hopper, it will wait to
3. Stable TM/
stabilize the sample products in the weighing hopper and begin to read the load cell
data in order to ensure the precision. Unit is 10ms.
30
4. Weigh HP Dly ly//Weigh Hopper Delay: It refers to delay how much time for the
weigh hopper to feed products into the timing hopper after opening the timing hopper.
unit is 10ms.
5. Time HP Dlyly//Timing hopper delay: It refers to delay how much time for the timing
hopper to discharge products into the packaging machines after opening the weigh
hopper, in order to ensure all the materials in the timing hopper and then allow next
discharge. Unit is 10ms.
6. FD HP Motor
Motor/Feed hopper motor mode: It refers to the running model of the feed
hopper motor; you can use the preset 5 kinds of ‘feed motor model’ in the ‘system
setup’ menu. The default factory setting is that the bigger this value is, the faster the
speed is. Input 0-4,recommendation:0-3.
31
7. WG HP Motor otor/Weigh hopper motor mode: It refers to the running model of the
weigh hopper motor; you can use the preset 5 kinds of ‘feed motor model’ in the
‘system setup’ menu. The default factory setting is that the bigger this value is, the
faster the speed is. Input 0-4,recommendation:0-3.
8. Tm HP Motor otor/ Timing hopper motor mode: It refers to the running model of the
timing hopper motor; you can use the preset 5 kinds of ‘feed motor model’ in the
‘system setup’ menu. The default factory setting is that the bigger this value is, the
faster the speed is. Input 0-4,recommendation:0-2.
9. FD HP Opn Tm/Feed hopper opened time: It refers that the feed hopper cover will
open how much time and then begin to close its cover in order to discharge all the
products in the feed hopper. unit is 10ms.Recommendation:1-20.
10. WG HP Opn Tm/ Weigh hopper opened time: It refers that the weigh hopper
cover will open how much time and then begin to close its cover in order to discharge
all the products in the timing hopper. Unit is 10ms.Recommendation:1-20.
11. Tm HP Opn Tm/Timing hopper opened time: It refers that the timing hopper
cover will open how much time and then begin to close its cover in order to discharge
all the products. Unit is 10ms.Recommendation:1-20.
32
Methods of setting up delay time, motor mode and open time of 1.6L multihead weigher with different products:
33
⒊ When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
Weighing of nut series such as
series(such pistachios):
Peanuts, macaroni, broad beans, pistachios
as:Peanuts,
Characteristic:Easy-flow, density between 0.5~1Kg/L,maxi length is between 3-5cm.
Target WT
10~ 101~ 201~ 301~ 401~ 501~ 601~ 701~ 801~ 901~
100g 200g 300g 400g 500g 600g 700g 800g 900g 1000g
Parameter
Lin VB Delay 22~24 24~26 26~28 26~30 28~31 29~32 30~33 30~34 31~34 32~35
Feed HP DLY 22~24 24~26 26~28 26~30 28~31 29~32 30~33 30~34 31~34 32~35
FD HP Motor 2 2 1 1 1 0 0 0 0 0
WG HP Motor 2 2 1 1 1 0 0 0 0 0
FD HP Opn Tm 1 1 1 1 2 2 2 2 3 5
WG HP Opn Tm 1 1 1 1 2 2 2 2 3 5
*Weigh HP Dly(1) 0 0~5 2~5 2~8 5~10 6~10 8~12 10~15 10~18 12~20
* Weigh HP Dly (2) 0~5 5~10 7~15 10~20 15~25 20~30 25~35 30~40 35~45 40~50
* Time HP Dly 55~65 55~68 58~70 60~70 62~70 65~70 68~75 70~78 70~80 70~80
* TM HP Motor 2 2 2 2 2 2 2 2 2 2
* Tm HP Opn Tm(1) 1 1 1 2 3 4 5 6 8 10
* Tm HP Opn Tm (2) 1 3~10 5~15 10~20 15~25 20~30 25~35 30~40 35~45 40~50
* Notes: 1. When Timing HP Mode is 0, Weigh HP Dly, Time HP Dly, TM HP Motor and Tm HP Opn Tm don’t work.
2. When Timing HP Mode is 1,please refer to Weigh HP Dly(1), Tm HP Opn Tm(1),Time HP Dly and TM HP Motor.
34
3. When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
Weighing of granule products Such as: seeds, rice, peanuts, soybeans, sugar
products(Such sugar):
Characteristic:Easy-flow, density between 0.33~0.8Kg/L,maxi length is within 1.5cm.
Target WT
10~ 101~ 201~ 301~ 401~ 501~ 601~ 701~ 801~ 901~
100g 200g 300g 400g 500g 600g 700g 800g 900g 1000g
Parameter
Lin VB Delay 20~23 22~25 24~28 26~30 28~30 28~32 29~33 30~33 31~33 31~35
Feed HP DLY 20~23 22~25 24~28 26~30 28~30 28~32 29~33 30~33 31~33 31~35
FD HP Motor 3 3 2 2 2 1 1 1 0 0
WG HP Motor 3 3 2 2 2 1 1 1 0 0
FD HP Opn Tm 1 1 1 1 1 1 1 1 2 3
WG HP Opn Tm 1 1 1 1 1 1 1 1 2 3
* Weigh HP Dly(1) 0 0 0 2 4 5 6 7 8 10
* Weigh HP Dly (2) 0 0~5 5~10 5~12 7~15 13~20 12~22 17~25 20~28 20~30
* Time HP Dly 55~63 57~65 60~70 61~70 62~70 63~70 65~70 65~72 68~75 70~75
* TM HP Motor 2 2 2 2 2 2 2 2 2 2
* Tm HP Opn Tm(1) 1 1 1 1 2~5 3~6 4~7 5~8 6~9 7~10
* Tm HP Opn Tm (2) 1 1 4~8 5~10 8~15 10~20 13~22 15~25 18~27 20~30
* Notes: 1. When Timing HP Mode is 0, Weigh HP Dly, Time HP Dly, TM HP Motor and Tm HP Opn Tm don’t work.
2. When Timing HP Mode is 1,please refer to Weigh HP Dly(1), Tm HP Opn Tm(1),Time HP Dly and TM HP Motor.
3. When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
35
Weighing of Candy series Such as: chewing gum, konfyt, kink sugar, fruit
series(Such sugar):
fruityy sugar
Characteristic:Easy-flow, density between 0.1~0.45Kg/L,maxi length is within 5cm.
Target WT
10~ 101~ 151~ 201~ 251~ 301~ 351~ 401~ 451~
51~100g
Parameter 50g 150g 200g 250g 300g 350g 400g 450g 500g
Lin VB Delay 20 20~22 22~24 24~26 26~28 26~30 27~30 28~30 28~31 28~32
Feed HP DLY 20 20~22 22~24 24~26 26~28 26~30 27~30 28~30 28~31 28~32
FD HP Motor 3 3 3 3 3 2 2 2 2 2
WG HP Motor 3 3 3 3 3 2 2 2 2 2
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1
* Weigh HP Dly(1) 0 0 0 0 0 0 0 0 0 0
* Weigh HP Dly (2) 0 0 0 0 2~4 4~6 5~8 6~10 8~13 10~15
* Time HP Dly 55~60 57~60 58~60 58~62 60~63 60~65 62~67 65~70 67~72 70~75
* TM HP Motor 2 2 2 2 2 2 2 2 2 2
* Tm HP Opn Tm(1) 1 1 1 1 1 1 1 1 1 1
* Tm HP Opn Tm (2) 1 1 1 1 2~4 4~6 5~8 6~10 8~13 10~15
* Notes: 1. When Timing HP Mode is 0, Weigh HP Dly, Time HP Dly, TM HP Motor and Tm HP Opn Tm don’t work.
2. When Timing HP Mode is 1,please refer to Weigh HP Dly(1), Tm HP Opn Tm(1),Time HP Dly and TM HP Motor.
3. When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
36
Weighing of Candy series Such as: chewing gum, konfyt, kink sugar, fruit
series(Such sugar):
fruityy sugar
Characteristic:Easy-flow, density between 0.4~1Kg/L,maxi length is within 4-8cm.
Target WT
10~ 101~ 201~ 301~ 401~ 501~ 601~ 701~ 801~ 901~
Parameter 100g 200g 300g 400g 500g 600g 700g 800g 900g 1000g
Lin VB Delay 20~22 22~25 26~28 26~29 27~30 28~30 28~31 29~31 30~33 32~35
Feed HP DLY 20~22 22~25 26~28 26~29 27~30 28~30 28~31 29~31 30~33 32~35
FD HP Motor 2 2 1 1 1 0 0 0 0 0
WG HP Motor 2 2 1 1 1 0 0 0 0 0
FD HP Opn Tm 1 1 1 1 2 1 1 2 4 5
WG HP Opn Tm 1 1 1 1 2 1 1 2 4 5
* Weigh HP Dly(1) 1 1 1 1 3 3~6 4~8 6~10 8~12 10~15
* Weigh HP Dly (2) 1 3 5 6~10 8~13 10~15 13~18 15~20 17~25 20~30
* Time HP Dly 55~65 55~70 58~70 60~70 62~70 65~70 65~75 70~75 70~78 70~80
* TM HP Motor 2 2 2 2 2 2 2 2 2 2
* Tm HP Opn Tm(1) 1 1 1 1 1 2~5 3~6 4~8 5~10 6~10
* Tm HP Opn Tm (2) 1 3 5 5~8 6~10 8~12 10~15 12~18 15~20 15~25
* Notes: 1. When Timing HP Mode is 0, Weigh HP Dly, Time HP Dly, TM HP Motor and Tm HP Opn Tm don’t work.
2. When Timing HP Mode is 1,please refer to Weigh HP Dly(1), Tm HP Opn Tm(1),Time HP Dly and TM HP Motor.
37
3. When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
Weighing of frozen food Such as: glutinous rice balls, dumplings, meatballs, ravioli
food(Such ravioli):
Characteristic:Easy-flow, density between 0.5~1.5Kg/L,maxi length is within 4-8cm.
Target Weight
200g~250g 251g~300g 301g~350g 351g~400g 401g~450g 451g~500g 501g~550g 551g~600g
Parameter
Lin VB Delay 25~28 26~28 26~29 27~29 27~30 28~31 29~32 30~33
Feed HP DLY 25~28 26~28 26~29 27~29 27~30 28~31 29~32 30~33
FD HP Motor 2 2 1 1 1 1 0 0
WG HP Motor 2 2 1 1 1 1 0 0
FD HP Opn Tm 1 1 1 1 1 1 1 2
WG HP Opn Tm 1 1 1 1 1 1 1 2
* Weigh HP Dly(1) 0 0 1 1 2 3 4 5
* Time HP Dly 55~65 55~70 58~70 60~70 62~70 63~71 65~75 70~75
* TM HP Motor 2 2 2 2 2 2 2 2
* Tm HP Opn Tm(1) 1 1 1 1 1 1 1 1
38
2. When Timing HP Mode is 1,please refer to Weigh HP Dly(1), Tm HP Opn Tm(1),Time HP Dly and TM HP Motor.
3. When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
Weighing of puffy food Such as: potato chips, fries, popcorn, shrimp fries
food(Such chips):
fries,, shrimp chips
Characteristic:Easy-flow, density between 0.05~0.3Kg/L,maxi length is within 7cm.
Target weight
10g~25g 26g~50g 51g~75g 76g~100g 101g~125g 126g~150g 151g~175g 176g~200g
Parameter
Lin VB Delay 22~25 23~26 24~27 25~28 26~29 27~30 28~31 28~32
Feed HP DLY 22~25 23~26 24~27 25~28 26~29 27~30 28~31 28~32
FD HP Motor 1 1 1 1 1 1 0 0
WG HP Motor 1 1 1 1 1 1 0 0
* Weigh HP Dly(1) 0~10 5~15 10~20 10~25 15~40 20~45 25~45 30~50
* Weigh HP Dly (2) 30~50 30~55 35~60 35~70 40~80 45~90 50~100 60~110
* Time HP Dly 55~65 55~70 58~70 60~70 62~70 63~71 65~75 70~75
* TM HP Motor 0 0 0 0 0 0 0 0
* Tm HP Opn Tm(1) 0~10 5~15 10~20 10~25 15~40 20~45 25~45 30~50
* Tm HP Opn Tm (2) 30~50 30~55 35~60 35~70 40~80 45~90 50~100 60~110
* Notes: 1. When Timing HP Mode is 0, Weigh HP Dly, Time HP Dly, TM HP Motor and Tm HP Opn Tm don’t work.
39
2. When Timing HP Mode is 1,please refer to Weigh HP Dly(1), Tm HP Opn Tm(1),Time HP Dly and TM HP Motor.
3. When Timing HP Mode is 2 or 3, please refer to Weigh HP Dly(2), Tm HP Opn Tm(2),Time HP Dly and TM HP Motor.
40
4.3. Stable time setup
Stable Tm of 10 head Multihead weigher< 6000 Speed - Feed HP Dly
6000÷Speed
Speed(bags/min) 60 50 40 30
Feed HP Dly(10ms) 20~26 22~30 24~35 26~45
Stable Tm(10ms) 74~80 90~98 115~126 120~140
Stable Tm of 14 head Multihead weigher < 6000 ÷(Speed÷2) - Feed HP Dly
Speed(Bags/Min) 110 100 90 80
Feed HP Dly(10ms) 20~25 22~30 23~35 25~40
Stable Tm(10ms) 84~89 90~98 98~110 110~125
Case1 : If a customer wants to weigh peanut (target weight is 100g) with 10 head
weigher, the customer expects the speed to reach 48 bags/min, how should
the parameters be set?
Analysis: Firstly the target speed should be a little faster than the expected speed
(target speed is suggested to be set as 50 bags/min), and according to the size
and characteristic of the product (to ensure no products jamming when
hopper closing door after discharging product, please refer toP32,P33,suggest
Feed HP Dly value as 22), finally we can calculate the Maxi stable time is 98
on the basis of above formula.
Case2: If a customer wants to weigh fries (target weight is 100g) with 10head weigher,
the customer expects the speed to reach 48 bags/min, how should the
parameters be set
Analysis: Firstly the target speed should be little faster than the expected speed (target
speed is suggested to be set as 50 bags/min),and according to the size and
characteristic of the product (Single piece of fry is very light but with big
volume and strip shape to ensure no product jamming when hopper closing
door after discharging product, please refer toP38,suggest Feed HP Dly value
as 28),finally we can calculate the Maxi stable time is 92 on the basis of
above formula.
Case3:If a customer wants to weigh pistachio nuts (Target weight is 100g) with 14
head weigher, the customer expects the speed to reach 100 bags/min, how
should the parameters be set?
Analysis: Firstly the target speed should be little faster than the expected speed (target
speed is suggested to be set as 103 bags/min),secondly the type of product
is nut(please refer to P32,P33),Feed HP Dly as 22, finally we can calculate
the Maxi stable time is 93 on the basis of above formula.
41
4.4. Setup of sample filter
Please set up the Sample Filter according to the requirement and Stable TM.
Sample Filter: It refers to the capacity of resisting disturbance level of each load cell,
the bigger the value is, the higher the capacity of resisting disturbance
is, but the slower the load cell reaction is. Notes: please refer to P13.
Case 1 : A customer weighs macaroni, target weight is 50g, with 10 head multihead
weigher, expected speed is 60 bags/min.
Analysis:Firstly we know that the product is nut series (please refer to P32,33), Feed
Analysis
HP Dly is 22, from Setup of Stable Tm we know Stable TM is 77,finally we know that
the Sample Filter (refer to P40) is 6.
Case 2 : A customer weighs macaroni ,target weight 50g, with 14 head multihead
weigher, expect speed 100 bags/min.
Analysis:According to the below forms, we know that Feed HP Dly is 22, Stable TM
Analysis
is 98, finally we know that the Sample Filter (refer to P41) is 8.
Summary: when the target weight and stable TM are fixed ,we can improve the
accuracy by improving the value of Sample Filter.
42
weight::
Setup of Stable TM and Sample Filter of 10 head multihead weigher with different target weight
Sample Filter Stable TM
Target Weight
10g~100g 5 6 7 8 9 10 10 10
101g~200g —— 6 6 7~8 9 10 10 10
201g~300g —— 5 5 6 7~8 9 10 10
301g~400g —— —— 5 6 7~8 9 10 10
401g~500g —— —— —— 5~6 7 8~9 10 10
501g~600g —— —— —— —— 6~7 8~9 10 10
601g~700g —— —— —— —— 6 7~8 9~10 10
701g~800g —— —— —— —— —— 7~8 9~10 10
801g~900g —— —— —— —— —— 7~8 9 10
901g~1000g —— —— —— —— —— 7 8~9 10
Notes: The above Stable TM and Sample Filter is on the basis of 10 head multihead weigher of 1.6L bucket.
43
weight::
Setup of Stable TM and Sample Filter of 14 head multihead weigher with different target weight
Sample Filter Stable T.
Target Weight
10g~100g 5 6 7 8 9 10 10 10
101g~200g —— 6 6 7~8 9 10 10 10
201g~300g —— 5 5 6 7~8 9 10 10
301g~400g —— —— 5 6 7~8 9 10 10
401g~500g —— —— —— 5~6 7 8~9 10 10
501g~600g —— —— —— —— 6~7 8~9 10 10
601g~700g —— —— —— —— 6 7~8 9~10 10
701g~800g —— —— —— —— —— 7~8 9~10 10
801g~900g —— —— —— —— —— 7~8 9 10
901g~1000g —— —— —— —— —— 7 8~9 10
Notes: The above Stable TM and Sample Filter is on the basis of 14 head multihead weigher of 1.6L bucket.
44
parameterss setup
4.5.Other parameter
Program Setup 1
1. Main AMP
AMP/Main Vibrator Amplitude: It refers to the strength of the main vibrator
amplitude.
2. LIN AMP
AMP/Linear Vibrator Amplitude: It refers to the strength of the linear vibrator
amplitude.
VB Feed Tm/Vibrator Feed time: It refers the period for the main and linear
3.VB
vibrators to feed the products to the feed hopper. Unit as 10ms.
The product fed into feed hoppers is not only affected by Vibrator AMP and VB feed
Tm, but also by the thickness of material on the linear vibrator pan, the thickness of
material can be controlled by the height of Upper Storage Funnel and length of
plastic strip.
Secondly: Control the thickness according to the target weight of product, such as
sunflower seeds (It will cause ‘landslide’ easily if the product is too thick) ,when we
weigh sunflower seeds, target weight is 100g, if the product is too thick, ‘landslide’
will easily occur.
45
Thirdly:When the material in the upper storage funnel is low, the Z conveyer will feed
material into it. If the surface of the product is very smooth and easy flowing (such as
frozen dumpling and ball gum), product may push others to slide into feed hopper
unintentionally, it will result in bad combination. Suggestion: please install the level
sensor above the upper storage funnel and set up No Prod Pau T as 1.
4. Over Sgl Tm/Overweight signal time: It means the standing time for the weigher
send ‘has dumped signal’ to the back machines when it dumps the overweight
material. unit as 10ms.
5. Stagger Dump Tm Tm: When there is a limit max dump hoppers, that’s to say, one
combination will be divided into several dumping with a certain interval to
discharge. unit as 10ms.
6. Multicomb TMS TMS/Multi-combination Times: it means that to finish one target
weigh will be divided into how many times to discharge. single dosing weight
=target weigh/N, the function is mainly used in big target weight.
When we weigh a product of 3000g target weight, it will cause product jamming
easily when discharge in one time, if we set up Multicomb TMS as 3, it means
1000g each time.
First time:999.5g
Second time:1000.1g
Third time:1000.4g (target weight-dosing weight of last two time),this way can
optimize the final accuracy.
7. Max Dump HPS HPS/Max Dumping hoppers: it means to limit the max simultaneous
dumping hoppers in a combination dumping in order to reduce the block of puffy
products.
Relevant parameter: Stagger Dump Tm
8. Min HP WT%WT%/Minimum single hopper weight%: it means that the single hopper
weight is less than the single combination target weight percent, which is
regarded as ‘low product’ and not allowed to attend the combination, and it needs
feeding material. unit as %.
9. IDLE
IDLE/No combination times: it’s applicable to limit the products remaining times
in the weight hopper. If one hopper is not selected to join combination for N times,
at N+1 times it is forced to be selected and join combination.
46
10 . Dump Sgl Dly ly/Dumping signal delay: Under the circumstance of ready
combinations, the combination weigher will dump material to the packaging
machine after receiving the “dump request signal” from packing machine, then
delay a period of time and send a 10ms ‘confirmed signal’ to the packaging
machine. Unit as 10ms.
For Example: If this delay time is too short, the VFSS machine may start the packing
action during product falling and cause product jamming. If the time is too long, the
VFFS machine may start the packing action till next product falling into the tube.
As shown in the drawing:
Program Setup-2:
1. AFC
AFC: Auto-adjust amplitude model selection.
A. 0: means to close this function.
B. AFCT, it will adjust the amplitude according to the combination hoppers and it
will give an auto adjustment to all linear vibrator amplitudes;
C. AFCW, it will adjust the amplitude according to the single hopper weight and
it will give an auto adjustment to every linear amplitude and display singly.
————AFCT————
a) Avg Comb Hps ps/AVG Combination hoppers: It refers to the average combination
hoppers which are used in a successful combination weighing. Recommendation:
3.0-4.0.
b) Acpt Comb Err Err/Single Acceptable combination error hoppers: It refers to the
average combination error hoppers which are used in each successful combination.
Recommendation: 0.3-1.0
c) Track Interval
Interval/Track Interval: After how many successful combinations, it will
47
give an auto adjustment to all linear amplitudes. Recommendation: 10.
AFCT Working Procedures
Procedures:
A. The linear amplitudes are too strong which leads to less combination hoppers, and
need adjusting.
The actual total combination hoppers after the combination in a track interval <((AV
combination hoppers - Single acceptable error) ×Track Interval) ≡>All linear
amplitudes-1.
B. The linear amplitudes are too weak which leads to more combination hoppers, and
need adjusting.
The actual total combination hoppers after the combination in a track interval >((AV
combination hoppers –Single acceptable error ) × Track Interval ) ≡ > All linear
amplitudes + 1.
————AFCW————
a) Avg HP Wt%/ Single AVG Hopper weight percent: It refers to the ideal average
weight of single hopper, and it is calculated as certain percent of single combination
weight. Recommendation: 20%-40%
b) ACPT HP Wt Err Err/Single Hopper Acceptable Error Weight: it refers to the single
allowable hopper weight error in the running. Recommendation: 1.0g
nterval/Track interval: After how many successful combinations for
c) Track Interval
each single hopper, it will give an auto adjustment to the linear amplitude of the
single hopper. Recommendation: 10
AFC
AFCW W Working Procedures
Procedures:
A. Single linear amplitude is too strong which leads to overweight of the single
hopper, and needs adjusting.
The actual single hopper weight after the combination in a track interval >((Single
AV weight ﹪ × Single acceptable error) × Track Interval) ≡ > Single linear
amplitude-1.
B. Single linear amplitude is too weak which leads to light weight of the single hopper,
and needs adjusting.
The actual single hopper weight after the combination in a track interval < ((Single
AV weight% × Single target combination weight - Single acceptable error ) ×
Track Interval) ≡>Single linear amplitude+1.
2. Auto Zero Tm Tm/INTERVAL: Used to set interval Automatic Zero Resetting in the
running process. unit is 1 min. Recommendation: 5
3. Single Piece Wt/Standard piece weight: the single piece standard weight for the
uniform products which is applicable to calculate the combination weight to
finish the target pieces.
4. Target Pcs cs: the target pieces of the weighing products.
1. Note:Relevant parameter: Piece Mode
5. Over Pcs cs/Over pieces limit: the up allowable limit of the weighed products.
6. Under Pcs cs/Under piece limit: the down allowable limit of the weighed
products.
7. Level Feed Time ime/Level products feed time: When the products photoelectric
level sensor check there is no enough products in the upper storage funnel, it will
output ‘feeding signal’ and till check there is enough materials in the upper
storage funnel. So it refers to the lasting time of the feeding signal. Unit is 1s.
Recommendation: 5-10.
48
8. Start Feed WT. /start feed weight: It refers to the weight for the machine to send
'feeding' signal when the top product level load cell checks there is not enough
products on the upper storage funnel. (Note: This is useful for the combinations
weighers using Main Vibrator with load cell) Range:0-32000.Unit is 0.1kg.
9. Stop Feed WT :/
WT:/:/stop feed weight:: It refers to the weight for the machine to stop
'feeding' signal when the top product level load cell check this weight which
means there is enough products on the upper storage funnel. (Note: This is useful
for the combinations weighers using Main Vibrator with load cell)
10. Copy To/copy this program to: The current parameter will be saved in another
program number. Default as the original program No. If you want to copy, input
the target program No., and press E to confirm. Range: 1-50.
Notes:Other parameters setup, please refer to Chapter 8 “Quick training version”.
Notes
The charts below show the result of 10 head weigher weighing fries of 50g target
weight with different setup:
Chart one:
Displayed weight(DW) 50 50.1 50 50.1 50 50
Real weight 49.1 51 49.5 50.8 48.8 51.4
Error between DW and RW 0.9 0.9 0.5 0.7 1.2 1.4
Error between RW and TW 0.9 1 0.5 0.8 1.2 1.4
Error between DW and TW 0 0.1 0 0.1 0 0
From the chart we can see :
Displayed accuracy= 0+0.1+0+0.1+0+0
accuracy=(0+0.1+0+0.1+0+0
0+0.1+0+0.1+0+0)÷ ÷6=0.03g good ;
6=0.03g,good
Average Error between DW and RW =(0.9+0.9+0.5+0.7+1.2+1.4
0.9+0.9+0.5+0.7+1.2+1.4
0.9+0.9+0.5+0.7+1.2+1.4)÷ ÷6=0.93g,bad.
Real accuracy= 0.9+1+0.5+0.8+1.2+1.4
accuracy=(0.9+1+0.5+0.8+1.2+1.4
0.9+1+0.5+0.8+1.2+1.4)÷ ÷6=0.97g Ba
6=0.97g,Ba
Bad.
Conclusion: Displayed accuracy is much better, but average error between DW
accuracy..
and RW is bad, which result in bad real accuracy
Notes:: Accuracy refers to the average error.
Notes
Chart two:
Displayed weight(DW) 50.8 51.1 50.2 50.7 50.6 52
Real weight 50.7 51 50.3 50.5 50.6 51.8
Error between DW and RW 0.1 0.1 0.1 0.2 0 0.2
Error between RW and TW 0.7 1 0.3 0.5 0.6 1.8
Error between DW and TW 0.8 1.1 0.2 0.7 0.6 2
49
From the chart we can see :
Displayed accuracy =(0.8+1.1+0.2+0.7+0.6+2
0.8+1.1+0.2+0.7+0.6+2
0.8+1.1+0.2+0.7+0.6+2)÷6=0.6g6=0.6g bad
6=0.6g,bad
bad;
Average Error between DW and RW =(0.1+0.1+0.1+0.2+0+0.2
0.1+0.1+0.1+0.2+0+0.2)÷6=0.12g
0.1+0.1+0.1+0.2+0+0.2 6=0.12g
6=0.12g,good.
Real accuracy =(0.7+1+0.3+0.5+0.6+1.8
0.7+1+0.3+0.5+0.6+1.8 6=0.81g
0.7+1+0.3+0.5+0.6+1.8)÷6=0.81g bad.
6=0.81g,bad.
Conclusion: Average error between DW and RW is much better, but displayed
accuracy..
accuracy is bad, which result in bad real accuracy
Notes: Accuracy refers to the average error.
Chart three
Displayed weight(DW) 50 50.1 50 50.2 50 50.3
Real weight 49.9 50.1 50 50 50.3 50.1
Error between DW and RW 0.1 0 0 0.2 0.3 0.2
Error between RW and TW 0.1 0.1 0 0 0.3 0.1
Error between DW and TW 0 0.1 0 0.2 0 0.3
From the chart we can see :
Displayed accuracy =(0+0.1+0+0.2+0+0.3)÷6=0.1g,good。
Average Error between DW and RW =(0.1+0+0+0.2+0.3+0.2)÷6=0.13g,good.
Real accuracy =(0.1+0.1+0+0+0.3+0.1)÷6=0.1g,good.
Conclusion: Increase displayed accuracy and optimize average error between
DW and RW RW,, we can increase real accuracy.
Notes: Accuracy refers to the average error.
1 8 10 14 13
2 28 45 91 66
3 56 120 364 165
4 70 210 1001 210
5 56 252 2002 126
6 28 210 3003 28
7 8 120 3432 1
8 1 45 3003
9 10 2002
From the chart we can see that when Avg Comb Hps is the half of all the hoppers, it
has most combinations.
50
Such as: 8 head weigher can combine 70 times per minute when the combination hoppers are four
(the highest).
10 head weigher can combine 252 times per minute in five hoppers (the highest).
14 high-precision model, it can combine 3432 times per minute in seven hoppers (the highest).
14 high-speed model, it can combine 210 times per minute in four hoppers (the highest).
The following is the data of 10 head weigher weighing spaghetti with different Avg
Comb Hps:
51
Feet of multihead weigher
Ground wire
Ground wire
Parameter setup — — Firstly make sure that every weigh hopper is in working
conditions; secondly, check whether the equipment is running smoothly without
products jamming.
The following is the weighing data with different stable time and filter time:
52
displayed weight and real weight. When the sample filter increases ,it is necessary to
increase the stable time.
53
Secondly, reduce linear vibrator amplitude;
After finishing the above mentioned steps, the actual combination hoppers will
increase accordingly. It will have best accuracy when the actual combination hoppers
are between 4~5;
‘AFC’ principle shows that: When actual average combination hoppers are more than
5, it means there are too little products in each hopper. This belongs to the second
circumstance.
Firstly, increase the height of upper storage funnel to control the thickness of product.
Please remember to increase the lever sensor at the same time as shown in figure:
After finishing the above mentioned steps, the actual combination hoppers will reduce
accordingly, it will have best accuracy when the actual combination hoppers are
between 4~5;
If the number of actual average combination hoppers remains large even when linear
vibrator amplitude reaches 80, then VB Feed Tm needs to be increased too.
54
5.2.2 Product jamming
Diagnosis of product jamming and the solutions:
Firstly : Doors of bucket close before all the product is discharged. The likely
diagnosis is HP motor mode is too fast and HP open time is too short.
Solution: Motor mode slower and increase HP open time, Lin VB Delay, Feed HP
Delay, Weigh HP Delay (with timing hopper).
Notes: please refer to chapter four.
Secondly: Product has been discharged into bucket before doors closed completely.
The likely diagnosis is that Lin VB Delay and Feed HP Delay are too short;
Solution: increase Lin VB Delay and Feed HP Delay.
Solution:
Notes: please refer to chapter four.
Thirdly: When the equipment firstly enters the working state, the combined influence
of improperly adjusted product thickness, larger vibrator amplitude and the easy
flowing nature of the products could all cause jamming to occur.
Solution: reduce the height of upper storage funnel and Lin VMP.
Notes:please refer to chapter five section two.
5.2.3 Forei
Forei gn objects inside weigh hopper
eign
The accuracy of single load cell is vital. It is the foundation of accurate weighing for
multihead weigher. It will affect the accuracy of the load cell when weigh hopper is
not emptied properly therefore affecting the accuracy of the combination weighing as
a whole; the following will provide the guide to check the possible presence of any
foreign objects:
he
firs
t
ste
p
55
The second step The third step
Notes: Go to Manual Test as the first step;select all the load cells for checking;
check the value of each load cell at the third step; discharge out the products in
weigh hopper at the fourth step;initialize zeroing operation for all the load cells at
the fifth step;select weigh hoppers at the sixth step;check the current value of each
load cell to judge whether there are any foreign objects in hopper. operate the sixth
and seventh steps repeatedly, the normal value of load cell could float within 0.2g; if
some load cells float between 0.7g and back to ±0.2g slowly, it indicates some feet
of multihead weigher have unstable contact with working platform. if the value
floats over 1g, it indicates the weigh hopper is not emptied properly, needs to be
checked immediately.
56
5.2.4 Calibration
Please refer to instruction manual.
Details observation
Scenario One :the system works inconsistently, please check the screen.
(1) Icon ‘L’ appears frequently which suggests the weight inside the hopper is less
than the MIN HP WT%, please increase amplitude of the linear vibrators.
(2) The number of average combination hopper is greater than optimum setting which
means re-feeding and re-combination are likely to occur, please increase the
amplitude of all the linear vibrators
(3) The product on the top cone is too thin and the upper storage funnel is too low, or
the product is not easy flowing, please increase the height of upper storage funnel.
(4) Z conveyer cannot supply enough products to multihead weigher, please increase
the product on the bucket and the speed of Z conveyer.
57
Scenario Two: The system works consistently, but the speed is less than expected
speed by 2 or 3 bags.
(2) Reduce the sample filter and Feed HP Dly on acceptable scope.
Scenario Three :The time interval in-between two discharging action ( the end of the
sealing acting and the dump of the next lot ) is too distant, please move forward the
discharging request signal according to the connecting methods.
Secondly, Z conveyer does not feed when multihead weigher runs low. Firstly make
short circuit of two receiving signal, if Z conveyer still does not work, it indicates the
problem is within the Z conveyer, if Z conveyer starts working after short circuit, it
indicates no signal output from multihead weigher. Secondly check if sending part and
receiving part of level sensor are at the right direction, in normal situation, the
indicator light is on.
Thirdly, multihead weigher don’t discharge product. Please check if there are ‘U、C、
Q、Y、W’ displayed on the screen, these letters indicate the multihead weigher is ready
and waiting for the request signal, you just need to check if there is signal inputted
when No Comb Action is set at 0. If there is no above mentioned letters displayed,
one possibility is too many heads are disabled, another possibility is the value of Min
HP WT% is too small, the other one possibility is the value of Combn HPS is too big.
Notes::
Notes
1) Working hoppers<Combn HPS
Take 10 head weigher as an example, if one head is disable, another head is
make zeroing, there is just 8 hoppers working, if we set Combn HPS as 9,when
there is no qualified combination, the machine will stop working.
Solution Combn HPS
Solution:Combn Working hoppers
HPS<Working hoppers-11
2) Working hoppers×Min HP WT%<1
Take 8 head weigher as an example, if we set Min HP WT% as 10,target weight
200g, weight of single hopper is 22g, 22>200×10%,8×22<200g,in the
situation multihead weigher will stop working, it is suggested to set Min HP
WT% as 15.
Solution:
Solution:(Working Hoppers-11)×Min
Working Hoppers Min HP WT% >1
3) Combn HPS HPS×Min Min HP WT%
WT%<1。
Take 8 head weigher as an example, generally we set Combn HPS as 7,Min HP
WT% as 10, target weight as 100g, 7×(100×10%)=70〈100(target weight),
meanwhile if another head displays ‘ L’, multihead will stop working, too.
Solution
Solution:Min Min HP WTWT%≥11÷Combn
Combn HPHPSS
4) No Comb Action, 0:Auto enforced dumping;1:Manual interfere. Multihead
weigher will stop working when there is no qualified combination, if we set the
No Comb Action as 1.
58
Chapter Six The connection of combination weigher
and computer
To help you quickly understand the daily productivity and production volume of
packaging systems, our company’s combination weigher series not only can connect
the printer, but also can transmit the statistical data of production directly through the
R232 to your computer, we can see the production situation, packaging quantity of
various specifications, the total weight of product, passing rate and the production
time-consuming very intuitively. We will introduce the whole process of connecting
the combination weigher with computer to you in the following:
Firstly, you need to install the computer connection software provided by our
company. This software requires XP system supporting. Secondly, you need data
connection cable, depending on your computer configuration. If it is necessary, you
can transfer RS232 output port to the computer through the USB interface converter.
Next, we will introduce the whole process of transferring data between combination
weigher and computer:
59
60
61
When your computer's communication ports are inconsistent with
software communication ports, it will appear 'Open the serial port error'
tips, which is normal.
62
63
Please note: You can turn off the software, then open, or choose 'stop
communication' in the toolbar, and then start .
All production
data display area
64
The filter data
display area
Note: This operation has sent all the production records to your computer. In order to
help you know production situation, you need to choose running program number,
target weight, the upper and lower deviation, the start time and end time as basis to
classify the data. Draw' √ ' in front of filter basis, meanwhile it will appear the
specific basis of indicators, and then click 'Refresh', your expected data will be shown
in the ' filter data display area'. Take "Procedure number" as filter basis and
"program number one" as specific basis indicator for example, the steps described
below:
And then click “Refresh”, “the filter data display area” will read the data
in ‘all the production data display area’.
Note: After this operation, we will find obviously that the data records of program
number 2 in ‘the filter data display area ’ disappear.
65
Note: Make sure Save and then close the file, then find the file store addresses to
open.
66
67
Finally, click on ‘Save’, the entire data transfer and operation will be completed
basically. The file is saved with Excel format. We can see the file save address as
follow:
68
Chapter Seven
Seven:: Weighing of puffy food
7.1.Characteristic
Characteristic: some puffy food is large in volume but small in weight, fragile, not
easy flowing and easy jamming, such as potato chips; some puffy food is small in
volume and also small in weight, easy flowing, such as fries and popcorn; some puffy
food is of moderate volume and weight, easy flowing, such as pistachio nuts.
69
Chapter Nine Quick training version
——Reference parameters for various kind of product
70
Model Reference parameters for weighing puffed foods with 1.6L
hopper of 10 head weigher
Prods
Parameter Weighing potato strips Weighing potato chips
72
Model
Reference parameters for weighing nuts with 1.6L hopper of 10 head weigher
Prod.
Parameter Weighing broad bean, peanut, spaghetti
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 450 500 800 1000 2000
Preset speed 65 63 60 57 55 53 50 48 46 44 40 60 60
Over WT. 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2
Under WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Correct WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Main AMP 40 45 47 50 55 55 57 59 61 62 66 62 66
Lin AMP 36 43 45 47 49 50 52 55 56 57 60 57 60
VB Feed TM 20 22 24 26 30 32 34 40 40 45 50 40 45
Lin VB delay 20 20 22 24 26 26 28 28 30 30 31 30 32
Feed HP Dly 20 20 22 24 26 26 28 28 30 30 31 30 32
Weigh HP Dly — — — — — — — — — — — — —
Time HP Dly — — — — — — — — — — — — —
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 55 56 57 58 59 60 61 62 63 64 65 65 65
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0 0 0
Stable time 72 74 76 78 80 82 84 86 88 90 100 90 95
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 1 2 3
Max dump HPS 0 0 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4.2 4.3 4.4 4.4 4.4 4.5 4.5 4.5 4.6 5 5 5
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24 25 25
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
Tm HP Opn Tm — — — — — — — — — — — — —
FD HP Motor 3 3 2 2 2 1 1 1 1 1 0 1 0
WG HP Motor 3 3 2 2 2 1 1 1 1 1 0 1 0
TM HP Motor — — — — — — — — — — — — —
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 20 20 20 20 20 20 20 20 20 20 20 20 20
Stop Feed WT 100 100 100 100 100 100 100 100 100 100 100 100 100
Notes: Reference parameters when Tm HP mode:0
73
Model Reference parameters for weighing candy with 1.6L hopper
of 10 head weigher
Prods.
Parameter Weighing twist candy, fruit candy
75
——Reference parameters when Tm HP mode:1
76
Model Reference parameters for weighing puffy foods with 1.6L
hopper of 10 head weigher
Product
Parameter s Weighing potato strips Weighing potato chips
79
Model Reference parameters for weighing candy with 1.6L hopper
of 10 head weigher
Prods.
Parameter Weighing twist candy, fruit candy
81
——Reference parameters when Tm HP mode:2 or 3
82
Model Reference parameters for weighing puffy foods with 1.6L
hopper of 10 head weigher
Prods.
Parameter Weighing potato strips Weighing potato chips
85
Model Reference parameters for weighing candy with 1.6L hopper
of 10 head weigher
Prod.
Parameter Weighing twist candy, fruit candy
87
14 head multihead weigher
88
Model Reference parameters for weighing puffy foods with 1.6L
hopper of 14 head weigher
Prods
Parameter Weighing potato strips Weighing potato chips
Next page Program setup 1 Program setup 1
Target WT 50 100 150 200 250 20 50 100 150 200
Preset speed 110 80 55 50 45 110 100 50 45 40
Over Wt 1 1 1 1 1 1 1 1 1 1
Under Wt 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0
Main AMP 45 50 55 60 65 50 55 60 65 70
Lin AMP 42 45 48 50 55 45 50 55 60 65
VB Feed TM 20 25 30 35 40 20 30 40 45 50
Lin VB delay 22 25 28 30 32 24 27 30 32 33
Feed HP Dly 22 25 28 30 32 24 27 30 32 33
Weigh HP Dly — — — — — — — — — —
Time HP Dly — — — — — — — — — —
Over Sgl Tm 10 10 10 10 10 10 10 10 10 10
Dump Sgl Dly 56 58 60 62 65 58 61 65 68 70
Stagger Dump Tm 0 0 0 0 0 0 0 0 0 0
Stable Tm 86 88 76 80 82 86 88 78 80 82
Multicomb TMS 1 1 1 1 1 1 1 1 1 1
Max Dump HPS 0 0 0 0 0 0 0 0 0 0
Min HP WT% 11 11 11 11 11 11 11 11 11 11
IDLE 100 100 100 100 100 100 100 100 100 100
Previous page Program setup 2 Program setup 2
AFC 2 1 1 1 1 2 1 1 1 1
Avg Comb Hps 4 4 7 7.4 7.5 4 4 7 7.4 7.5
Acpt Comb Err 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
Track Interval 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 25 24 20 20 20 24 22 20 19 18
ACPT HP Wt Err 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Track Interval 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 2 4 1 1 3 5 7
WG HP Opn Tm 1 1 1 2 4 1 1 3 5 7
Tm HP Opn Tm — — — — — — — — — —
FD HP Motor 2 2 2 1 1 1 1 0 0 0
WD HP Motor 2 2 2 1 1 1 1 0 0 0
TM HP Motor — — — — — — — — — —
Top Cone MD 1 1 1 1 1 1 1 1 1 1
Level Feed T 5 5 5 5 5 5 5 5 5 5
Start Feed WT 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 1 1 1 0 0 1 1 1
Notes: Reference parameters when Tm HP mode:0
89
Model Reference parameters for weighing frozen foods with 1.6L
hopper of 14 head weigher
Prod
Parameter Weighing dumpling, meatball, rice glue ball
Next page Program setup 1
Target WT 200 300 400 500 800 1000 2000
Preset speed 110 105 100 95 60 60 60
Over Wt 1 1.5 2 2 2 2 2.5
Under Wt 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0
Main AMP 45 50 55 60 50 55 60
Lin AMP 42 45 48 50 50 55 60
VB Feed TM 20 25 30 35 20 30 40
Lin VB delay 22 25 28 30 28 30 32
Feed HP Dly 22 25 28 30 28 30 32
Weigh HP Dly — — — — — — —
Time HP Dly — — — — — — —
Over Sgl Tm 10 10 10 10 10 10 10
Dump Sgl Dly 58 60 60 62 65 68 70
Stagger Dump Tm 0 0 0 0 0 0 0
Stable Tm 86 90 95 100 95 100 100
Multicomb TMS 1 1 1 1 2 2 4
Max Dump HPS 0 0 0 0 0 0 0
Min HP WT% 11 11 11 11 11 11 11
IDLE 11 11 11 11 11 11 11
Previous page Program setup 2 Program setup 2
AFC 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4
Acpt Comb Err 0.3 0.3 0.3 0.3 0.3 0.3 0.3
Track Interval 5 5 5 5 5 5 5
Avg HP Wt% 25 25 25 25 25 25 25
ACPT HP Wt Err 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Track Interval 5 5 5 5 5 5 5
Auto Zero Tm 5 5 5 5 5 5 5
FD HP Opn Tm 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1
Tm HP Opn Tm — — — — — — —
FD HP Motor 2 2 1 1 1 1 1
WD HP Motor 2 2 1 1 1 1 1
TM HP Motor — — — — — — —
Top Cone MD 1 1 1 1 1 1 1
Level Feed T 5 5 5 5 5 5 5
Start Feed WT 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:0
90
Model
Reference parameters for weighing nuts with 1.6L hopper of 14 head weigher
Prod
Paramet. Weighing broad bean, peanut, spaghetti
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 450 500 700 1000 2000
Preset speed 115 110 105 100 95 92 90 88 85 82 75 60 60
Over Wt 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2.5
Under Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Main AMP 40 45 47 50 55 55 57 59 61 62 66 62 66
Lin AMP 36 43 45 47 49 50 52 55 56 57 60 57 60
VB Feed TM 20 22 24 26 30 32 34 40 40 45 50 40 45
Lin VB delay 20 20 22 24 26 28 28 30 30 30 31 30 32
Feed HP Dly 20 20 22 24 26 28 28 30 30 30 31 30 32
Weigh HP Dly — — — — — — — — — — — — —
Time HP Dly — — — — — — — — — — — — —
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 55 56 57 58 59 60 61 62 63 64 65 68 70
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 78 82 86 88 90 93 96 98 100 102 110 100 108
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 1 2 3
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24 25 25
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
Tm HP Opn Tm — — — — — — — — — — — — —
FD HP Motor 3 3 3 2 2 2 1 1 1 1 0 1 0
WG HP Motor 3 3 3 2 2 2 1 1 1 1 0 1 0
TM HP Motor — — — — — — — — — — — — —
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:0
91
Model Reference parameters for weighing candy with 1.6L hopper of
14 head weigher
Prods
Parameter Weighing twist candy, fruit candy, konfyt
Next page Program setup 1
Target WT 100 200 300 400 500 800 1000 1500 2000 2500
Preset speed 110 100 95 90 85 60 60 60 50 50
Over Wt 1 1 2 2 2 2 2 2 2 2
Under Wt 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0
Main AMP 50 55 47 50 55 55 57 59 61 62
Lin AMP 45 50 52 55 60 55 60 60 60 60
VB Feed TM 25 26 30 35 40 35 40 40 40 40
Lin VB delay 20 24 26 28 30 28 30 30 30 30
Feed HP Dly 20 24 26 28 30 28 30 30 30 30
Weigh HP Dly — — — — — — — — — —
Time HP Dly — — — — — — — — — —
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 58 60 62 64 65 67 70 75 78 80
Stagger Tm 0 0 0 0 0 0 0 0 0 0
Stable Tm 88 95 100 104 110 104 108 108 108 108
Multicomb TMS 1 1 1 1 1 2 2 3 4 5
Max Dump HPS 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1
Tm HP Opn Tm — — — — — — — — — —
FD HP Motor 3 3 3 2 1 2 1 1 1 1
WG HP Motor 3 3 3 2 1 2 1 1 1 1
TM HP Motor — — — — — — — — — —
Top Cone MD 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:0
92
Model Reference parameters for weighing small granular product with
1.6L hopper of 14 head weigher
Prods
Parameter Weighing rice, white sugar, melon seeds, pignut
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 500 600 1200
Preset speed 115 110 105 100 95 90 85 80 75 70 60
Over Wt 1 1 2 2 2 2 2 2 2 3 3
Under Wt 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0
Main AMP 50 55 47 50 55 55 57 59 61 62 65
Lin AMP 45 50 52 55 60 55 60 60 60 60 60
VB Feed TM 20 24 26 28 30 30 30 34 36 40 40
Lin VB delay 24 26 28 30 32 35 36 38 40 40 40
Feed HP Dly 24 26 28 30 32 35 36 38 40 40 40
Weigh HP Dly — — — — — — — — — — —
Time HP Dly — — — — — — — — — — —
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 55 56 57 58 59 60 61 62 63 64 65
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 82 86 90 94 96 98 100 104 108 110 110
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 2
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 11
IDLE 100 100 100 100 100 100 100 100 100 100 100
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1 1
Tm HP Opn Tm — — — — — — — — — — —
FD HP Motor 3 3 3 2 2 1 1 1 1 1 1
WG HP Motor 3 3 3 2 2 1 1 1 1 1 1
TM HP Motor — — — — — — — — — — —
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:0
93
—— Reference parameters when Tm HP mode:1
——Reference
94
Model. Reference parameters for weighing puffy foods with 1.6L
hopper of 14 head weigher
Prod.
Parameter Weighing potato strips Weighing potato strips
Next page Program setup 1 Program setup 1
Target WT 50 100 150 200 250 20 50 100 150 200
Preset speed 110 80 55 50 45 110 100 50 45 40
Over Wt 1 1 1 1 1 1 1 1 1 1
Under Wt 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0
Main AMP 45 50 55 60 65 50 55 60 65 70
Lin AMP 42 45 48 50 55 45 50 55 60 65
VB Feed TM 20 25 30 35 40 20 30 40 45 50
Lin VB delay 22 25 28 30 32 24 27 30 32 33
Feed HP Dly 22 25 28 30 32 24 27 30 32 33
Weigh HP Dly 5 10 20 30 35 10 15 20 35 50
Time HP Dly 58 62 65 70 70 60 62 65 66 70
Over Sgl Tm 10 10 10 10 10 10 10 10 10 10
Dump Sgl Dly 40 41 42 43 44 40 41 42 43 44
Stagger Dump Tm 0 0 0 0 0 0 0 0 0 0
Stable Tm 86 88 76 80 82 86 88 78 80 82
Multicomb TMS 1 1 1 1 1 1 1 1 1 1
Max Dump HPS 0 0 0 0 0 0 0 0 0 0
Min HP WT% 11 11 11 11 11 11 11 11 11 11
IDLE 100 100 100 100 100 100 100 100 100 100
Previous page Program setup 2 Program setup 2
AFC 2 1 1 1 1 2 1 1 1 1
Avg Comb Hps 4 4 7 7.4 7.5 4 4 7 7.4 7.5
Acpt Comb Err 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
Track Interval 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 25 24 20 20 20 24 22 20 19 18
ACPT HP Wt Err 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Track Interval 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 2 4 1 1 3 5 7
WG HP Opn Tm 1 1 1 2 4 1 1 3 5 7
Tm HP Opn Tm 5 10 20 30 35 10 15 20 35 50
FD HP Motor 2 2 2 1 1 1 1 0 0 0
WG HP Motor 2 2 2 1 1 1 1 0 0 0
TM HP Motor 0 0 0 0 0 0 0 0 0 0
Top Cone MD 1 1 1 1 1 1 1 1 1 1
Level Feed T 5 5 5 5 5 5 5 5 5 5
Start Feed WT 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 1 1 1 0 0 1 1 1
Notes: Reference parameters when Tm HP mode:1
95
Model Reference parameters for weighing frozen foods with 1.6L
hopper of 14 head weigher
Prods
Parameter Weighing dumpling, meatball, rice glue ball
Next page Program setup 1
Target WT 200 300 400 500 800 1000 2000
Preset speed 110 105 100 95 60 60 60
Over Wt 1 1.5 2 2 2 2 2.5
Under Wt 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0
Main AMP 45 50 55 60 50 55 60
Lin AMP 42 45 48 50 50 55 60
VB Feed TM 20 25 30 35 20 30 40
Lin VB delay 22 25 28 30 28 30 32
Feed HP Dly 22 25 28 30 28 30 32
Weigh HP Dly 0 0 1 3 5 7 12
Time HP Dly 62 63 65 66 66 67 70
Over Sgl Tm 10 10 10 10 10 10 10
Dump Sgl Dly 35 35 36 36 37 38 40
Stagger Dump Tm 0 0 0 0 0 0 0
Stable Tm 86 90 95 100 95 100 100
Multicomb TMS 1 1 1 1 2 2 4
Max Dump HPS 0 0 0 0 0 0 0
Min HP WT% 11 11 11 11 11 11 11
IDLE 11 11 11 11 11 11 11
Previous page Program setup 2 Program setup 2
AFC 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4
Acpt Comb Err 0.3 0.3 0.3 0.3 0.3 0.3 0.3
Track Interval 5 5 5 5 5 5 5
Avg HP Wt% 25 25 25 25 25 25 25
ACPT HP Wt Err 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Track Interval 5 5 5 5 5 5 5
Auto Zero Tm 5 5 5 5 5 5 5
FD HP Opn Tm 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1
Tm HP Opn Tm 1 1 1 1 2 3 8
FD HP Motor 2 2 1 1 1 1 1
WD HP Motor 2 2 1 1 1 1 1
TM HP Motor 0 0 0 0 0 0 0
Top Cone MD 1 1 1 1 1 1 1
Level Feed T 5 5 5 5 5 5 5
Start Feed WT 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:1
96
Model
Reference parameters for weighing nuts with 1.6L hopper of 14 head weigher
Prods
Paramet. Weighing broad bean, peanut, spaghetti
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 450 500 700 1000 2000
Preset speed 115 110 105 100 95 92 90 88 85 82 75 60 60
Over Wt 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2.5
Under Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Main AMP 40 45 47 50 55 55 57 59 61 62 66 62 66
Lin AMP 36 43 45 47 49 50 52 55 56 57 60 57 60
VB Feed TM 20 22 24 26 30 32 34 40 40 45 50 40 45
Lin VB delay 20 20 22 24 26 28 28 30 30 30 31 30 32
Feed HP Dly 20 20 22 24 26 28 28 30 30 30 31 30 32
Weigh HP Dly 0 0 0 0 0 0 0 0 0 0 6 10 20
Time HP Dly 60 62 63 65 67 68 69 70 70 70 75 75 75
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 35 35 35 35 36 36 37 37 37 38 39 39 40
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 78 82 86 88 90 93 96 98 100 102 110 100 108
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 1 2 3
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24 25 25
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
Tm HP Opn Tm 1 1 1 1 1 1 1 1 1 1 3 5 10
FD HP Motor 3 3 3 2 2 2 1 1 1 1 0 1 0
WG HP Motor 3 3 3 2 2 2 1 1 1 1 0 1 0
TM HP Motor 2 2 2 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:1
97
Model Reference parameters for weighing candy with 1.6L hopper of
14 head weigher
Prod.
Parameter Weighing twist candy, fruit candy
Next page Program setup 1
Target WT 100 200 300 400 500 800 1000 1500 2000 2500
Preset speed 110 100 95 90 85 60 60 60 50 50
Over Wt 1 1 2 2 2 2 2 2 2 2
Under Wt 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0
Main AMP 50 55 47 50 55 55 57 59 61 62
Lin AMP 45 50 52 55 60 55 60 60 60 60
VB Feed TM 25 26 30 35 40 35 40 40 40 40
Lin VB delay 20 24 26 28 30 28 30 30 30 30
Feed HP Dly 20 24 26 28 30 28 30 30 30 30
Weigh HP Dly 1 1 1 1 3 6 10 11 13 15
Time HP Dly 60 62 65 66 67 70 70 70 70 70
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 36 36 36 37 37 38 40 42 44 45
Stagger Tm 0 0 0 0 0 0 0 0 0 0
Stable Tm 88 95 100 104 110 104 108 108 108 108
Multicomb TMS 1 1 1 1 1 2 2 3 4 5
Max Dump HPS 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1
Tm HP Opn Tm 1 1 1 1 1 4 6 8 10 12
FD HP Motor 3 3 3 2 1 2 1 1 1 1
WG HP Motor 3 3 3 2 1 2 1 1 1 1
TM HP Motor 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:1
98
Model Reference parameters for weighing small granular product with
1.6L hopper of 14 head weigher
Prod.
Parameter Weighing rice, white sugar, melon seeds, pignut
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 500 600 1200
Preset speed 115 110 105 100 95 90 85 80 75 70 60
Over Wt 1 1 2 2 2 2 2 2 2 3 3
Under Wt 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0
Main AMP 50 55 47 50 55 55 57 59 61 62 65
Lin AMP 45 50 52 55 60 55 60 60 60 60 60
VB Feed TM 20 24 26 28 30 30 30 34 36 40 40
Lin VB delay 24 26 28 30 32 35 36 38 40 40 40
Feed HP Dly 24 26 28 30 32 35 36 38 40 40 40
Weigh HP Dly 0 0 0 0 0 0 2 3 4 5 12
Time HP Dly 62 63 64 65 67 68 69 70 70 70 70
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 35 35 35 35 35 36 36 36 37 37 38
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 82 86 90 94 96 98 100 104 108 110 110
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 2
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 11
IDLE 100 100 100 100 100 100 100 100 100 100 100
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1 1
Tm HP Opn Tm 1 1 1 1 1 1 1 1 2 2 7
FD HP Motor 3 3 3 2 2 1 1 1 1 1 1
WG HP Motor 3 3 3 2 2 1 1 1 1 1 1
TM HP Motor 2 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:1
99
——Reference parameters when Tm HP mode:
mode:22 or 3
100
Model Reference parameters for weighing puffy foods with 1.6L
hopper of 14 head weigher
Prod.
Parameter Weighing potato strips Weighing potato strips
Next page Program setup 1 Program setup 1
Target WT 50 100 150 200 250 20 50 100 150 200
Preset Speed 110 80 55 50 45 110 100 50 45 40
Over Wt 1 1 1 1 1 1 1 1 1 1
Under Wt 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0
Main AMP 45 50 55 60 65 50 55 60 65 70
Lin AMP 42 45 48 50 55 45 50 55 60 65
VB Feed TM 20 25 30 35 40 20 30 40 45 50
Lin VB delay 22 25 28 30 32 24 27 30 32 33
Feed HP Dly 22 25 28 30 32 24 27 30 32 33
Weigh HP Dly 30 40 60 75 90 30 40 50 70 90
Time HP Dly 58 62 65 70 70 58 60 62 65 70
Over Sgl Tm 10 10 10 10 10 10 10 10 10 10
Dump Sgl Dly 35 35 35 40 40 35 36 37 38 40
Stagger Dump Tm 0 0 0 0 0 0 0 0 0 0
Stable Tm 86 88 76 80 82 86 88 78 80 82
Multicomb TMS 1 1 1 1 1 1 1 1 1 1
Max Dump HPS 0 0 0 0 0 0 0 0 0 0
Min HP WT% 11 11 11 11 11 11 11 11 11 11
IDLE 100 100 100 100 100 100 100 100 100 100
Previous page Program setup 2 Program setup 2
AFC 2 1 1 1 1 2 1 1 1 1
Avg Comb Hps 4 4 7 7.4 7.5 4 4 7 7.4 7.5
Acpt Comb Err 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
Track Interval 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 25 24 20 20 20 24 22 20 19 18
ACPT HP Wt Err 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Track Interval 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 2 4 1 1 3 5 7
WG HP Opn Tm 1 1 1 2 4 1 1 3 5 7
Tm HP Opn Tm 30 40 60 75 90 30 40 50 70 90
FD HP Motor 2 2 2 1 1 1 1 0 0 0
WG HP Motor 2 2 2 1 1 1 1 0 0 0
TM HP Motor 0 0 0 0 0 0 0 0 0 0
Top Cone MD 1 1 1 1 1 1 1 1 1 1
Level Feed T 5 5 5 5 5 5 5 5 5 5
Start Feed WT 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 1 1 1 0 0 1 1 1
Notes: Reference parameters when Tm HP mode:2 or 3.
101
Model Reference parameters for weighing frozen foods with 1.6L
hopper of 14 head weigher
Prod.
Parameter Weighing dumpling, meatball, rice glue ball
Next page Program setup 1
Target WT 200 300 400 500 800 1000 2000
Preset Speed 110 105 100 95 60 60 60
Over Wt 1 1.5 2 2 2 2 2.5
Under Wt 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0
Main AMP 45 50 55 60 50 55 60
Lin AMP 42 45 48 50 50 55 60
VB Feed TM 20 25 30 35 20 30 40
Lin VB delay 22 25 28 30 28 30 32
Feed HP Dly 22 25 28 30 28 30 32
Weigh HP Dly 1 1 5 8 12 15 25
Time HP Dly 63 65 67 68 70 70 70
Over Sgl Tm 10 10 10 10 10 10 10
Dump Sgl Dly 35 35 35 35 35 40 40
Stagger Tm 0 0 0 0 0 0 0
Stable Tm 86 90 95 100 95 100 100
Multicomb TMS 1 1 1 1 2 2 4
Max Dump HPS 0 0 0 0 0 0 0
Min HP WT% 11 11 11 11 11 11 11
IDLE 11 11 11 11 11 11 11
Previous page Program setup 2 Program setup 2
AFC 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4
Acpt Comb Err 0.3 0.3 0.3 0.3 0.3 0.3 0.3
Track Interval 5 5 5 5 5 5 5
Avg HP Wt% 25 25 25 25 25 25 25
ACPT HP Wt Err 0.4 0.4 0.4 0.4 0.4 0.4 0.4
Track Interval 5 5 5 5 5 5 5
Auto Zero Tm 5 5 5 5 5 5 5
FD HP Opn Tm 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1
Tm HP Opn Tm 1 1 4 8 12 15 22
FD HP Motor 2 2 1 1 1 1 1
WG HP Motor 2 2 1 1 1 1 1
TM HP Motor 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1
Level Feed T 5 5 5 5 5 5 5
Start Feed WT 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:2 or 3.
102
Model Reference parameters for weighing nuts with 1.6L hopper of 14 head
weigher
Prod
Parameter Weighing broad bean, peanut, spaghetti
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 450 500 700 1000 2000
Preset Speed 115 110 105 100 95 92 90 88 85 82 75 60 60
Over Wt 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2.5
Under Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0 0 0
Main AMP 40 45 47 50 55 55 57 59 61 62 66 62 66
Lin AMP 36 43 45 47 49 50 52 55 56 57 60 57 60
VB Feed TM 20 22 24 26 30 32 34 40 40 45 50 40 45
Lin VB Delay 20 20 22 24 26 28 28 30 30 30 31 30 32
Feed HP Dly 20 20 22 24 26 28 28 30 30 30 31 30 32
Weigh HP Dly 2 4 6 8 10 12 13 14 15 18 30 40 65
Time HP Dly 60 62 64 65 66 68 70 70 70 70 75 70 70
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 35 35 35 35 35 35 35 35 35 36 37 38 40
Stagger Dump Tm 0 0 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 78 82 86 88 90 93 96 98 100 102 110 100 108
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 1 2 3
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24 25 25
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 2 3 2 3
Tm HP Opn Tm 2 4 6 8 9 10 11 12 13 16 28 38 60
FD HP Motor 3 3 3 2 2 2 1 1 1 1 0 1 0
WG HP Motor 3 3 3 2 2 2 1 1 1 1 0 1 0
TM HP Motor 2 2 2 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:2 or 3.
103
Model Reference parameters for weighing candy with 1.6L hopper of
14 head weigher
Products
Parameter Weighing twist candy, fruit candy.
Next page Program setup 1
Target WT 100 200 300 400 500 800 1000 1500 2000 2500
Preset speed 110 100 95 90 85 60 60 60 50 50
Over Wt 1 1 2 2 2 2 2 2 2 2
Under Wt 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0
Main AMP 50 55 47 50 55 55 57 59 61 62
Lin AMP 45 50 52 55 60 55 60 60 60 60
VB Feed TM 25 26 30 35 40 35 40 40 40 40
Lin VB Delay 20 24 26 28 30 28 30 30 30 30
Feed HP Dly 20 24 26 28 30 28 30 30 30 30
Weigh HP Dly 1 1 1 5 6 15 20 25 30 40
Time HP Dly 62 63 65 65 66 68 70 70 70 70
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 35 35 35 35 35 37 38 40 42 45
Stagger Tm 0 0 0 0 0 0 0 0 0 0
Stable Tm 88 95 100 104 110 104 108 108 108 108
Multicomb TMS 1 1 1 1 1 2 2 3 4 5
Max Dump HPS 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10
IDLE 500 500 500 500 500 500 500 500 500 500
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1
Tm HP Opn Tm 1 1 1 5 6 10 12 15 20 25
FD HP Motor 3 3 3 2 1 2 1 1 1 1
WG HP Motor 3 3 3 2 1 2 1 1 1 1
TM HP Motor 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:2 or 3.
104
Model Reference parameters for weighing small granular product with
1.6L hopper of 14 head weigher
Prod.
Parameter Weighing rice, white sugar, melon seeds, peanut
Next page Program setup 1
Target WT 50 100 150 200 250 300 350 400 500 600 1200
Preset speed 115 110 105 100 95 90 85 80 75 70 60
Over Wt 1 1 2 2 2 2 2 2 2 3 3
Under Wt 0 0 0 0 0 0 0 0 0 0 0
Correct Wt 0 0 0 0 0 0 0 0 0 0 0
Main AMP 50 55 47 50 55 55 57 59 61 62 65
Lin AMP 45 50 52 55 60 55 60 60 60 60 60
VB Feed TM 20 24 26 28 30 30 30 34 36 40 40
Lin VB Delay 24 26 28 30 32 35 36 38 40 40 40
Feed HP Dly 24 26 28 30 32 35 36 38 40 40 40
Weigh HP Dly 0 0 2 3 5 6 8 10 12 15 25
Time HP Dly 62 63 64 65 67 68 69 70 70 70 70
Over Sgl Tm 20 20 20 20 20 20 20 20 20 20 20
Dump Sgl Dly 35 35 35 35 35 35 35 35 35 38 40
Stagger Tm 0 0 0 0 0 0 0 0 0 0 0
Stable Tm 82 86 90 94 96 98 100 104 108 110 110
Multicomb TMS 1 1 1 1 1 1 1 1 1 1 2
Max Dump HPS 0 0 0 0 0 0 0 0 0 0 0
Min HP WT% 10 10 10 10 10 10 10 10 10 10 11
IDLE 100 100 100 100 100 100 100 100 100 100 100
Previous page Program setup 2
AFC 1 1 1 1 1 1 1 1 1 1 1
Avg Comb Hps 4 4 4 4 4 4 4 4 4 4 4
Acpt Comb Err 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Track Interval 5 5 5 5 5 5 5 5 5 5 5
Avg HP Wt% 26 25 25 25 25 25 25 24 24 24 24
ACPT HP Wt Err 1 1 1 1 1 1 1 1 1 1 1
Track Interval 5 5 5 5 5 5 5 5 5 5 5
Auto Zero Tm 10 10 10 10 10 10 10 10 10 10 10
FD HP Opn Tm 1 1 1 1 1 1 1 1 1 1 1
WG HP Opn Tm 1 1 1 1 1 1 1 1 1 1 1
Tm HP Opn Tm 0 0 2 3 5 6 8 10 12 15 25
FD HP Motor 3 3 3 2 2 1 1 1 1 1 1
WG HP Motor 3 3 3 2 2 1 1 1 1 1 1
TM HP Motor 2 2 2 2 2 2 2 2 2 2 2
Top Cone MD 1 1 1 1 1 1 1 1 1 1 1
Level Feed T 10 10 10 10 10 10 10 10 10 10 10
Start Feed WT 0 0 0 0 0 0 0 0 0 0 0
Stop Feed WT 0 0 0 0 0 0 0 0 0 0 0
Comb MD 0 0 0 0 0 0 0 0 0 0 0
Notes: Reference parameters when Tm HP mode:2 or 3.
105