Professional Documents
Culture Documents
Mainzer Landstraße 50
60325 Frankfurt am Main
Germany
ineos-styrolution.com
infopoint.emea@styrolution.com
Product Regulatory Overview (PRO)
Product: K-Resin® KR03
Version 1.1
Date: 27 April 2017
There is the potential for another substance that is known to the State of California to be a carcinogen
which may be present in trace quantities. This substance is cumene (isopropylbenzene) (CAS No. 98-
82-8). Though we do not routinely measure for this, the levels are expected to be very low.
We have no information to suggest that exposure to the low levels of above mentioned substances
found in our K-Resin poses any significant risk to the end-user or consumer.
Please note that the above mentioned substances are technically unavoidable. The mentioned residual
contents have been analysed on several test specimens. The observed maximum values are given
above. However, determination of residual monomers contents is not part of our continuous production
control. The values given can be used for general safety assessment but are not a specification.
Converters and manufacturers of finished articles must assess Prop 65 warning requirements based on
their specific situations.
Page 1/5
Product Regulatory Overview
Product: K-Resin® KR03
Version 1.1
Date: 27 April 2017
Given the above, we can state that the grade listed would be in compliance with the Consumer Product
Safety Improvement Act of 2008, H.R. 4040 and its enforced final limitations for calendar year 2011.
The following Ozone Depleting Substances, as listed in the above legislations and the Montreal
Protocol of 16th September 1987, are not intentionally used as additives or ingredients:
• Hazardous Air Pollutants as defined in Section 112(b)(1) of the U.S. Clean Air Act (40 CFR 61)
This product does contain trace amounts of the following substances regulated by Section 112(r) of the
U.S. Clean Air Act List of Regulated Flammable Substances for Accidental Release Prevention (40
CFR 68.130):
• 1,3-butadiene
This product does contain trace amounts of the following substances regulated by Section 111 of the
U.S. Clean Air Act List of Volatile Organic Compounds (VOC) (40 CFR 60.489):
• 1,3-butadiene
• Cyclohexane
• Ethylbenzene
• Styrene
The information above refers to the state of the laws at the date of issue. This confirmation expires after 12 months or in the case of
regulatory changes. When new statements are published on the internet portal, the former statements automatically become void. In
your own interest please regularly check the information on the internet portal.
It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are
observed. The statement provided is exclusively for our customers and respective competent authorities. It is not intended for
publication either in printed or electronic form (e.g. via Internet) by others. Thus, neither partial nor full publication is allowed without
written permission.
Page 2/5
Product Regulatory Overview
Product: K-Resin® KR03
Version 1.1
Date: 27 April 2017
Heavy metals
The sum of lead, cadmium, chromium-VI and mercury does not exceed the maximum value of 100 ppm
(i.e. 0.01%) as required by the CONEG (Coalition of North Eastern Governors) for the January 1, 1994.
Thus, also the maximum value for these elements laid down in Directive 94/62/EC as last amended by
Commission Directive 2013/2/EU is met.
Toys
European Standard EN71-3:2013 + A1:2014 and ISO 8124-3:2010 + AMD1:2014 set limits on the
migration of several metals. We wish to inform you that INEOS Styrolution does not deliberately add
any of these metals to the above grade and their concentrations therefore should not exceed the
migration limits set in the above mentioned standards. Please note that according to EN-71-3 and ISO
8124-3, the compliance of the material must be tested on the finished toy.
Residual Monomer
Typical values for styrene residuals in K-Resin® SBC products are below 10 ppm.
Phthalates
No phthalates, including di-(2-ethylhexyl) phthalate (DEHP), dibutyl phthalate (DBP), benzyl butyl
phthalate (BBP), diisononyl phthalate (DINP), diisodecyl phthalate (DIDP), and di-n-octyl phthalate
(DnOP), are intentionally added to this product. This product therefore meets the requirements of the
Consumer Product Safety Improvement Act of 2008 and EU Directive 2005/84/EC.
Batch 1 through 12 Challenge Substances as identified in the Canadian Environmental Protection Act,
1999. These substances were on the Domestic Substances List (DSL) and categorized as a) persistent,
The information above refers to the state of the laws at the date of issue. This confirmation expires after 12 months or in the case of
regulatory changes. When new statements are published on the internet portal, the former statements automatically become void. In
your own interest please regularly check the information on the internet portal.
It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are
observed. The statement provided is exclusively for our customers and respective competent authorities. It is not intended for
publication either in printed or electronic form (e.g. via Internet) by others. Thus, neither partial nor full publication is allowed without
written permission.
Page 3/5
Product Regulatory Overview
Product: K-Resin® KR03
Version 1.1
Date: 27 April 2017
bioaccumulative, and inherently toxic to the environment and that are known to be in commerce in
Canada; and/or b) a high hazard to humans and as having a high likelihood of exposure to individuals
in Canada.
Nanomaterial
This product is not a nanomaterial.
In addition, the manufacture of the product, no intentionally produced nanoparticles according to the
OECD definition (OECD, ISO, SCENIHR (2007b)) with an intended technical function based on their
nanoscaled structure like e.g. nano tubes, or materials intended to release nanoparticles in normal
conditions of use, are used as additives or ingredients.
Conflict minerals
Please be informed that “Conflict minerals” as defined by the Securities and Exchange Commission
(SEC), i.e. cassiterite, columbite-tantalite, gold, wolframite, and their derivatives, have not been
intentionally added as ingredients in the manufacture of the above mentioned product and, to the best
of our knowledge, are not known to be present in the final product.
Acrylamide
Alkylphenol Ethoxylates, including nonylphenol ethoxylate and octylphenol ethoxylate
Allergens, including but not limited to those listed in EU Regulation 1169/2011, Directives
2000/13/EC, 2003/89/EC, and Section B.01.010.1 (1) of Canadian Regulation C.R.C., c.
870 such as: peanuts, tree nuts, milk, eggs, wheat gluten, soybeans, fish and shellfish
Aromatic amines
Asbestos
Azo compounds
Bisphenol compounds, including but not limited to: BPA, BPB, BPC, BPE, BPF, BPS, and
BPZ
Brominated or halogenated flame retardants
Butylated Hydroxyanisole (BHA)
Chlorinated paraffins
Colorants or pigments
Cyanuric acid
Di(ethylhexyl) adipate (DEHA), diethyl hydroxyl amine (DEHA), or di(ethylhexyl)maleate
(DEHM)
Dimethylfumarate (DMF)
Dioxins or furans
Epoxy derivatives listed in EU Directives 2002/16/EC and 1895/2005
Formaldehyde
Melamine
Methyl bromide
Natural rubber latex, dry natural rubber, or synthetic latex
Organotin compounds
The information above refers to the state of the laws at the date of issue. This confirmation expires after 12 months or in the case of
regulatory changes. When new statements are published on the internet portal, the former statements automatically become void. In
your own interest please regularly check the information on the internet portal.
It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are
observed. The statement provided is exclusively for our customers and respective competent authorities. It is not intended for
publication either in printed or electronic form (e.g. via Internet) by others. Thus, neither partial nor full publication is allowed without
written permission.
Page 4/5
Product Regulatory Overview
Product: K-Resin® KR03
Version 1.1
Date: 27 April 2017
For notice:
Many substances are ubiquitous. The observance of all these substances is not part of our ongoing
production control. In view of the many factors that may affect processing and application of our
products, this information does not relieve the processor from carrying out own investigations and tests,
neither does this information imply any guarantee for certain properties nor the suitability of the product
for a specific purpose. It is the responsibility of the recipient of our products to ensure that any
proprietary rights and existing laws and legislation are observed.
Please note that this declaration is only valid for prime products.
If you have further questions, contact your local sales representative or send an E-Mail to:
infopoint.emea@styrolution.com.
Best regards
The information above refers to the state of the laws at the date of issue. This confirmation expires after 12 months or in the case of
regulatory changes. When new statements are published on the internet portal, the former statements automatically become void. In
your own interest please regularly check the information on the internet portal.
It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are
observed. The statement provided is exclusively for our customers and respective competent authorities. It is not intended for
publication either in printed or electronic form (e.g. via Internet) by others. Thus, neither partial nor full publication is allowed without
written permission.
Page 5/5