Pammw Back-to-Basics
Where should a Keyphasor®
transducer be mounted?
fevent) icp 0 the diver oto,
fosngand diagnostics. Consistent (event) ince :
phase information, before and faa not the coupling or 2 coupied
after outages, 8 abo necessary to \-—— component
evaluate the efficiency of the oe ‘+ Gearboxes and fluid davers should
‘machine overhaul. Please see the have a Keyphasor transducer on
by Larry Covina: * Each machine train component
picphrpe tin SS
mas oe
ces ee eee
Breen mee
As@teare FOE "Beaker
0 ct pes matt rnc eames
‘definition of phase lag ungle and ape each rocor element. These Key
absolute phase in the sidebar on phasor transducers must also view
page 27) Figure 1 an event integral to the gearbox or
‘When instrumenting machine trains uid drive rotor, noc the coupling or
for proper machinery protection, two (A0tChes or projections) eliminates coupled component.
‘common errors are made. 1) too few ‘Many potential pifallsandhelps provide 10a or dren components must
Keyphasortransducers,and 2) incorrect 800d diagnostic information. have a Keyphasor transducer, and it
placement of the Keyphasor trans- The following isa list of general rules must view an event integral t the
‘ducets. Proper location of Keyphasor for proper Keyphasor transducer loca diven rotor, not the coupling or a
transducers and reference markers tion, Refer to Figure 2 ‘coupled component
Compressor
26 omit June 1994‘When reference markers are located
(on monintegral rotor components,
such as couplings, stub sha, ack
shafts and shrink on-colas, phase
information maybe jeopardized dire
co rearrangement of the rotoc com
ponents during reassembly after an
outage. Locate these reference
‘markers on shafts oe their inegral
components
‘+ 4 Keyphasor transducer shoukl be
located as dose wo the thrust bearing
area as possibleto minimize thermal
Bprowth effects which could move
the reference markers out of view oF
the transducer,
1 Because notches are stress concen
{ators they should notbelocated in
high torque areas, such as at coup,
Ling hubs o fangs
‘+ Notehes or projections should be
‘designed! into the machine. The
lesign should include proper inter
nal radtuses, woth the width, dps
(or height and length hasod on trans:
‘Typical Notch
‘Typical Projection (see note below)
June 1994
ducer type, rotative speed and rotor tion sericea to the proper use and
Size. They should be lied up with configuration of diagnostic
the 4 Dalance hole, 0° on the bal Instruments
‘ance ring, or some other obvious ently Nevada can assist you with your
feanure of the shaft See Figure 3. rotating machinery and system installa
Topinar enchors oki be Santen one costae anal
eine poeme en acne
feet ane abe port aoe Comins Pais semen noes
Spe msudiophaercnnticy Nencacscoti gw sncenee
ee eta ‘Absolute phase- the ming
nove dae asa tm poanon (net fi nom
pase cena cates
Trane agl he ster
Sedmonee sahroamneye
ee eee
Scfoman fheshesah cee
fe ieeaiieeepie
ae
Installations shat ill use data acy
siuon systems, such as Bendy Nev
‘ada’s Dynamic Data Manager® 2,
‘Transient Data Manager® 2, Tran:
sient Data Interface External or
ADRES for Windows, should have
redundant Keyphasor transducers
Ioeatedat the same angular | PBtS lg angle «teeming
relationship, in degrees, between 2
Keyphasor pulse and the next pos:
Keyphasor transducer locations and | tye peal ofa bration signal ofthe
notch locations should be property — | me frequency.
documented. Accurate documenta:
oor lamar 152 men (6 none)
Rotation: COW
Loctlon: re eter utboard of hut bearngin ine wth
‘degrees on Selanoe rng, ce
fngth Sm (28 no)
Wah appro. 8 Ste 1 mm (0.751905 inch)
Depth: 131025mm G.061804 moro)
Rass: appre 98mm (0375 Inch)
Enmaducer ern pone 7
‘Setup: Gap at 3mm (05 noes oy rom th olor
Src
Machining Method: 19 mm (075 rch bal end, mi 10 suggestec doth wi
rng Met (0750 iret) bal end, il to suggests dep
Fotorciamotor = 152mm (6 Inches)
tation: CCW |
Location: Driver rotor cutboard of trust bearing nln with
Odegrees on balance rng
Length: 19 mm (0.75 inches)
Wath: 64 men 0.25 inches)
Helght:5 mm (0 2inches) above rote sutace
Transducer: 8 mm proximity probe
‘Setup: Gap at 6.4m (0.25 inches) any rom the rotor
=notviowing roection
[Machining Method: Fabrcate projecton, Seoure tortor
Ina postive fashion. Tiss tobe accomplished on an "os designed” basis and vit
‘ary by apateaton.
Note: Etrame care must bo taken to elminate safety cancers tom potential ioose
parts.
Figure 3
KeyphasrotVProjecion
i NT