Professional Documents
Culture Documents
DESCRIPTION
Bostik Boscoseal PU-X is a single component, ready
to use, highly elastic, cold applied polyurethane
waterproofing which cures into a membrane with
excellent abrasion, mechanical, chemical, thermal, and
UV resistance.
Bostik PU Sealant;
(20 mm X 20 mm,
CONCRETE SLAB
width to height dimension)
2. If there is dynamic crack beyond 1/16 inch, create a 1. Apply Bostik PU sealant as shown above with
V-cut shape profile using concrete grinder or router approximately 20mm width and 20mm height in all
with the size of approximately 2 inches on both edge corners where the floor meets the wall.
diagonally. 2. After the sealant has cured, create a strip of 25 wet
mils Boscoseal PU-X measuring 3 inches on each side.
Mixing COATING SYSTEM
Stir the material well by means of an electric stirrer 1. Maintenance or Occasional Pedestrian Traffic System
(approximately 500 rpm). Mixing time at least 2-3
minutes until homogenous mixture is achieved. Thickness Yield per
Product Consumption
per Coat 25 kg (17.9 L)
NOTE: Bostik Boscoseal Fabric can be used as
20 wet
1st Coat
reinforcement for wall-floor connections, pipe
Boscoseal mils
penetration, flashing etc. For this application, apply 0.4 L/m² 45m²
PU-X (16 dry
the 1st coat Boscoseal PU-X and then embed the mils)
Boscoseal Fabric and immediately apply 2nd coat of
Boscoseal PU-X.
20 wet
2nd Coat
Priming Boscoseal mils
0.4 L/m² 45m²
For porous substrates like concrete, cement mortar, or PU-X (16 dry
mils)
wood, use Boscoprime 1, then apply Boscoseal PU-X
within 2-3 hours (not later than 4 hours) when the primer
is still a little bit tacky.
For non-porous substrates like metals, ceramic tiles, use 2nd 1st
Boscoprime 3, then apply Boscoseal PU-X within Coat Coat
6-12 hours (not later than 24 hours) when the Primer
primer is still a little bit tacky. Bostik
Screed
PHYSICAL AND TECHNICAL DATA Concrete
PROPERTY RESULTS TEST METHOD Slab
Liquid
Form
Polyurethane
Boscoseal mils
Water Vapor 0.5 L/m² 36m²
>25 g/m²/day ISO 9932:91 PU-X (20 dry
Permeability mils)
Crack Bridging Up to 2mm
EOTA TR-008
Capability crack 25 wet
2nd Coat
Boscoseal mils
Shore 0.5 L/m² 36m²
65 ASTM D 2240 PU-X (20 dry
A Hardness mils)
Root
Resistant UNE 53420
Resistance
Adhesion
(Pull-Off) >2 MPa ASTM D 4541
Strength
2nd Coat
Service -30°C
In-house Lab 1st Coat
Temperature to +90°C
Primer
Between
Application
+10°C In-house Lab Bostik Screed
Temperature
to +35°C
Concrete Slab
*Technical Data are approximate values only, it is provided
according to a temperature of +20°C and relative
humidity of 50%.
OR RISK SIGNS
R23/24/25: Poisonous when inhaled, swallowed and
Topping
contacted with skin.
PACKAGING
25 kg
LIMITS
• Substrate moisture should be at most 5%
• Concrete slab must be minimum of 4 weeks old
• Minimum substrate temperature +10°C
• Maximum substrate temperature +30°C
• Maximum air humidity 85% r.h.
• Observe dew point temperature
• For best result, maximum thickness of Boscoseal
PU-X is 0.5 mm dry film thickness per layer
PT BOSTIK INDONESIA
Atrium Setiabudi Building, 2nd floor, Suite 203 A
Jl. HR. Rasuna Said Kav. 62 Kuningan BOSTIK HOTLINE
Jakarta 12920, Indonesia
Phone : +62 21 521 0404
Fax : + 62 21 521 0554 Layanan Bantuan +62 21 521 0404
www.bostik.com
an ARKEMA company