Previous Pageblock Return to Previous Menu Next Pageblock
Pratt & Whitney
STANDARD PRACTICES MANUAL (PN 585005)
VISUAL INSPECTION − INSPECTION/CHECK−06
Task 70−31−00−220−106:
R 1. Visual Inspection Standards For LPT Vanes (All JT8D, JT9D, JT3D, R FT8, PW2000, PW4000, And PW6000 Engines)
NOTE: Refer to 70−31−00, General−01 (Task 70−31−00−200−001) for
the definitions of the abnormal conditions specified in this visual inspection standard.
A. Metallurgical Imperfections
NOTE: Unless specified differently, linear imperfections
are not permitted.
R NOTE: The subsequent limits supplement the inspection
R limits in the Engine Manuals/CIR (Cleaning, R Inspection, and Repair) Manuals for the specific R engines listed above. The limits are based on P & W R Quality Standards for newly manufactured parts.
(1) Imperfections less than 0.015 inch (0.381 mm) can be
non−bottomed.
(2) Imperfections 0.015 inch (0.381 mm) or greater must
have a bottom that you can see.
(3) Any imperfections that are back−to−back are not
permitted.
B. Blending Acceptance Limits
(1) Acceptance limits for vane blending of single and
paired vanes are given in Figure 801.
(2) Acceptance limits for vane cluster blending are given
in Figure 802.
#70−31−00 Page 801
EFFECTIVITY −ALL INSP/CK−06 DEC 1/07 000 Pratt & Whitney STANDARD PRACTICES MANUAL (PN 585005)
VISUAL INSPECTION − INSPECTION/CHECK−06
Vane Blending (Single And Paired Vanes) − Acceptance Limits
Figure 801 (Task 70−31−00−220−106) R R #70−31−00 Page 802 EFFECTIVITY −ALL INSP/CK−06 DEC 1/07 000 Pratt & Whitney STANDARD PRACTICES MANUAL (PN 585005)
VISUAL INSPECTION − INSPECTION/CHECK−06
1. Buttress. 0.015 Inch (0.381 mm) Deep
2. Edges. 0.015 Inch (0.381 mm) Deep 3. Platform. 0.015 Inch (0.381 mm) Deep With Length At Least Five Times The Depth Not In Fillet Radii 4. Leading Edge Not Within Hardpoint Datums. Gradual Transition Along The Edge, 0.500 Inch (12.700 mm) Long R By 0.010 Inch (0.254 mm) Deep With Resultant Flat 0.030 Inch (0.762 mm). Minimum Length−To−Depth Ratio Is 15:1. R 5. Leading Edge Fillet. 0.010 Inch (0.254 mm) Deep With Resultant Flat 0.030 Inch (0.762 mm)
Key to Figure 801
#70−31−00 Page 803
EFFECTIVITY −ALL INSP/CK−06 DEC 1/07 000 Pratt & Whitney STANDARD PRACTICES MANUAL (PN 585005)
VISUAL INSPECTION − INSPECTION/CHECK−06
Vane Cluster Blending − Acceptance Limits
Figure 802 (Task 70−31−00−220−106) R R #70−31−00 Page 804 EFFECTIVITY −ALL INSP/CK−06 DEC 1/07 000 Pratt & Whitney STANDARD PRACTICES MANUAL (PN 585005)
VISUAL INSPECTION − INSPECTION/CHECK−06
1. Platform. 0.015 Inch (0.381 mm) Deep, Not In Fillet Radii
2. Trailing Edge. Two Blends Total In Each Cluster. Gradual R Transition Along The Edge, 0.250 Inch (6.35 mm) Long By R 0.025 Inch (0.635 mm) Deep 3. Buttress. 0.015 Inch (0.381 mm) Deep 4. Leading Edge Not Within Hardpoint Datums. Gradual Transition Along The Edge, 0.500 Inch (12.700 mm) Long By 0.015 Inch (0.381 mm) Deep With Resultant Flat 0.030 Inch (0.762 mm). Minimum Length−To−Depth Ratio Is 15:1. R 5. Leading Edge Fillet. 0.010 Inch (0.254 mm) Deep With Resultant Flat 0.030 Inch (0.762 mm)