Professional Documents
Culture Documents
1 of 4 2 of 4
+ +
3 of 4 4 of 4
• Ship To Name
• Sales Order Number
Drawer Hardware
#8 - 1½” Hi Lo Screws 12mm Zinc Cam 34mm Black Twister Dowel ¾” Nail Drawer Slide Screw
(48) (48) (48) (60) (96)
Page 2 of 20
Bed Parts
B5
B6
B1
B3 B2
B2
B4 B3
B1
B4
B1 B2 B3 B4 B5 B6
Outer Gables (2) Inner Gables (2) Upper Stabilizer (2) Lower Stabilizer (2) Plywood Slats (9) Metal U-channel with
black black black black Blocks (2)
cherry cherry cherry cherry
espresso espresso espresso espresso
Page 3 of 20
STEP 1 Estimated Time: 10 minutes
Attach metal U-channels to each outer gable using drawer slide screws TOP
Large
hole
TOP
BOTTOM
TOP
BOTTOM
Drawer Slide
Screw
Page 4 of 20
STEP 3 Estimated Time: 10 minutes
Finished
Side
Bottom
Page 5 of 20
STEP 4 Estimated Time: 5 minutes
Insert JRN nuts into the holes on each end of the inner gables. The
holes are drilled through. You can insert them from either side.
B2
B2
Page 6 of 20
STEP 5 Estimated Time: 5 minutes
Identifying the upper and
lower stabilizers
Insert JRN nuts into the holes on each end
of the upper (B3) and lower (B4) stabilizers.
Upper Stabilizers
Top edge
(FINISHED) is
rounded
B3 Upper Stabilizers
Side hole is
close to the
UNFINISHED
edge
Lower Stabilizers
B4 Lower Stabilizers
Page 7 of 20
STEP 6 Estimated Time: 10 minutes
Attach “T” spacers and drawer glides to Inner Gables
Top
IMPORTANT:
7” Before attaching the drawer glides, determine the
TOP and BOTTOM of each inner gable.
A. Measure from each edge of the “T” Spacer to
each unfinished edge.
B. The measurement that is approximately 4” will
be the BOTTOM.
Check the position of the drawer glides carefully
before you attach them to the inner gables.
Bottom
Finished
Edge 4”
Drawer
Slide Screw
Unfinished Edge
Page 8 of 20
STEP 7 Estimated Time: 5 minutes
Using JCB connectors, and the Allen Key provided,
attach each lower stabilizer (B4), one at a time, to both
inner gables BELOW the drawer slide
B4
B4
Finished edge
IMPORTANT
Identifying the Lower Stabilizer
The screw hole is at the top, close to the finished edge
JCB
JRN
Connector
Nut
If you have any difficulty tightening the JCB connector,
use a screwdriver to adjust the JRN nut to make sure
the hole is facing the opening for the connector
Page 9 of 20
STEP 8 Estimated Time: 5 minutes
B3
Upper Stabilizer
The screw hole is closest
to the lower, unfinished
edge
Page 10 of 20
STEP 9 Estimated Time: 10 minutes
Attach one outer gable (B1) to stabilizers with JCB connectors
B1
Page 11 of 20
STEP 10 Estimated Time: 5 minutes
Lay the four metal braces, as shown, with the bend resting 10b
on top of the inner gables
10a
10a
10b
Bend 10a
10a 10a
Pre-drilled hole
10a
10b Secure the other (flat) end of the metal brackets to U-channel.
11a Spread the wooden slats out across the inner stabilizers
11b Slide the slats into the wide spaces of the metal U-channel (B6) on one outer gable. Remember that one
set of metal braces are still loose on one end.
11b
Slide
Page 13 of 20
STEP 12 Estimated Time: 10 minutes This Step easiest with 2 People
Carefully attach second outer gable to stabilizers
12a Secure the gable in place with with JCB connectors, but don’t fully tighten
12b Ensure the slats are set inside the u-channel and that they haven’t pulled out of the first outer gable.
Page 14 of 20
Drawer Parts Identification
D4
D2
D1
D5
Drawer Front (12)
black
cherry
espresso D3
D1
D2
Plywood
D3 D4 D5
Right Drawer Side (12) Drawer Back (12) Drawer Bottom (12)
unfinished
Plywood Unfinished
D2
D3
Page 15 of 20
14b Screw black twister dowels into drawer fronts
D1
14cCaAttach
binedrawer
t Pasides
rts toIddrawer
entifback
icawith
tio1½”
n Hi Lo screws
1½” Hi Lo Screws
Page 16 of 20
14d Attach drawer front and tighten cams
using a flat head screwdriver
Locked
Unlocked Locked
Turn 210° Unlocked Turn 210°
14e Turn drawer upside down and slide drawer bottom into grooves
Page 17 of 20
14f Secure the drawer bottom to the
C
drawer back with nails
Use 4 nails
per drawer
Groove on
drawer front
Page 18 of 20
14h Attach drawer slides to left and right drawer sides using drawer slide screws
Drawer
Slide
Screws
Drawer
Slide
Screws
Page 19 of 20
STEP 15 Estimated Time: 2 minutes
Insert drawers
Note: When drawers are installed correctly, you will not be able to
remove them without first lifting up the drawer front.
Thanks!
Page 20 of 20