Professional Documents
Culture Documents
EE-SX3173/4173-P Series
Built-in Photomicrosensor
Connector Type
• Mounted with M3 screws
• 5 VDC and 24 VDC power supply types are available
• Photo IC output (Dark-ON/Light-ON)
• Connector with secure lock compatible with JST GHR-03
• Equipped with a Zener diode, which increases noise immunity
(for EE-SX3173/4173-P3-Z only)
• Connector with cable is also available (order separately)
EE-5002 1M (Refer to page 7.)
Features
Models available
Power supply voltage: In addition to the conventional 5 VDC supply, Mounting: New model available with M3 screws
model also available with 24 VDC supply best for large devices
Board
7
4
3.2 dia.
3.2
14.7
14.8
13.6
Application Examples
1
EE-SX3173/4173-P Series
Model Number Structure
E E -S X@ @@ @-P @-@
(1) (2) (3) (4) (5) (6) (7)
(1) Sensing method (2) Operating mode (3) Structure (4) Mounting screw size
X: Transmissive 3: Dark-ON 1: Standard structure 7: M3
4: Light-ON
Ordering Information
Power
Sensing Connecting Aperture size Output Operating
Appearance Sensing distance supply Model
method method H x W (mm) type mode
voltage
Dark-ON EE-SX3173-P3-Z
Emitter 24 VDC
14.7
Transmissi 5 mm 1.4 × 1.4 Light-ON EE-SX4173-P3-Z
ve Connector Photo IC
(slot type) (Slot width) Detector Dark-ON EE-SX3173-P2
14.8 1.4 × 0.5 5 VDC
13.6 Light-ON EE-SX4173-P2
2
EE-SX3173/4173-P Series
Engineering Data (Reference Value)
Fig 1. Output Allowable Dissipation vs.
Ambient Temperature
Characteristics
100
Output allowable dissipation Pout (mW)
80
60
40
20
0
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100
Ambient temperature Ta (ºC)
Fig 2. Sensing Position Characteristics Fig 3. Sensing Position Characteristics Fig 4. Repeated Sensing Position
(Typical) (Typical) Characteristics
Output transistor
Output transistor
Output transistor
3
EE-SX3173/4173-P Series
Safety Precautions
To ensure safe operation, be sure to read and follow the Instruction Manual provided with the sensor.
Connection without a Load
WARNING If the power supply is connected directly without a load, the internal
This product cannot be used as a safety device for elements may explode or burn. Be sure to insert a load when
press machines or for protecting the safety of connecting the power supply.
persons. This product is designed for use in
applications for sensing workpieces and workers Vcc
that do not affect safety.
Sensor
OUT +
CAUTION -
Load
Vcc
Sensor
OUT
-
GND
+
Vcc
Sensor Load +
OUT
GND -
4
EE-SX3173/4173-P Series
Vcc
Example: EE-SX4173-P3-Z
OUT ZD 0.1 to 1 µF When inserting a load resistor (R = 5.6 kΩ) in the following device
GND
Counter Specifications
5
EE-SX3173/4173-P Series
Design
Design should be made so that light is completely shut off during
operation. We recommend that sensing objects are made of metal.
(With an infrared light sensor, infrared light will pass through the
sensing object made of resin, resulting in unstable detection.)
Vcc IN
Internal circuit
OUT
GND
+
- COM
Vcc CP1(N)
OUT CP2(N)
(Reset)
+
GND – Remote
controller for
input
External resistor
(+)
Vcc CP1(N)
OUT CP2(N)
+ + (Reset)
GND – –
(–)
* For details on external resistance calculation, see the text.
6
EE-SX3173/4173-P Series
Dimensions and Internal Circuit (Unit: mm)
Photomicrosensor
EE-SX3173-P3-Z 7
EE-SX4173-P3-Z 4
3.2 dia.
EE-SX3173-P2
3.2
EE-SX4173-P2
(7.5)
(14.8)
6.5 8.3 (Aperture width) 13.6
5.6 0.5 12.4 Mark surface (Brand
2.7 5 2.7 mark, model, lot)
Optical axis
A
1.4
6.4
8.4 7.5
Aperture size (H × W)
(14.7) (13.2)
Emitter Detector 6.3
2.4
1.4 × 1.4 1.4 × 0.5 Cross-section diagram A-A
A
Manufactured by JST
(Japan Solderless Terminal)
3 2 1 Unless otherwise specified, the
SM03B-GH tolerances are as shown below.
G G 10 18 ±0.35
18 30 ±0.42
Note: Dimensions in
parentheses are for
reference only.
7
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products
or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,
to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price
of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other
claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is
not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,
or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with
respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it
to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice
to change part numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be
assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to
confirm actual specifications of purchased Product.
OMRON Corporation
Electronic and Mechanical Components Company
Regional Contact
Americas Europe
https://www.components.omron.com/ http://components.omron.eu/
Asia-Pacific China
https://ecb.omron.com.sg/ https://www.ecb.omron.com.cn/
Korea Japan
https://www.omron-ecb.co.kr/ https://www.omron.co.jp/ecb/