Professional Documents
Culture Documents
.......
#500 Series Bearings
1
LuBo Industries, Inc.
.......
#500 Series Bearings
.......................................................................
.................................................................................................................................................
1
● Advantages of LuBo #500 Series Bearings
3
● Metric Size
15
● Inch Size
20
● LuBo #500 Self-Lubricating Spherical Bearings
....... 2 .......
LuBo Industries, Inc.
..... Advantages of LuBo #500 Series Bearings
-LuBo #500 Series Self-lubricating Bearings can be utilized where heavy loads must be supported at low to
medium speeds.
-Bearings have high mechanical strength with excellent wear resistance and self-lubrication properties
exhibiting stable performance and durability under severe operating conditions.
-No form of supplementary lubrication is required. A film of solid lubricant is transferred unto shaft as it starts to run
During operation, both of the surfaces burnish quickly and result in a highly polished bearing surface capable of
withstanding extreme pressure.
LuBo #500SP Flange Bushings LuBo #500SP Bushings LuBo #500B Bushings
LuBo #500SP Sliding Liners LuBo #500SP Thrust Washers LuBo #500SP Sliding Plates
3
LuBo Industries, Inc.
Advantages of LuBo #500 Series Bearings
.....
LuBo #500 Series Materials
Normally, copper alloy is used as the base material for LuBo #500 series bearings by centrifugal or sand casting.
Other materials such as cast iron, stainless steels and even tool steels could be used according to the applications
involving extreme temperatures, environments corrosive to bronze, and loads exceeding the compressive strength
of bronze.
-Bearing Materials
Code #500SP #500B #500F #500S #500AL #500SPX #500HCA
Copper Alloy Bronze Aluminum
Base Metal Cast Iron Stainless Steel Special Alloy Special Alloy
(High Strength) (Red Brass) Bronze
Chemical
General Use High Temp.
General Use Resistance High Higher Loads Higher Loads
Application High Load +400° C Sea Water
Medium Speed Temp. +600° C than #500SP than #500SPX
Under Water (+725°F)
(1,100° F)
NOTE : When used for high strength bearings, alloys LuBo #500SP, #500SPX and #500HCA require hardened shafts.
-Solid Lubricants
A bearing and its mating surface should always be separated by a film of lubricant. LuBo produces proprietary solid
lubricant compounds consisting of graphite, PTFE, metallic oxides, white metals, waxes, and other minerals that
are compressed and heat treated into dense plugs. These plugs are then installed into the base metal.
Lubricants used in LuBo products are solid, permanent, and completely self-lubricating. They are constantly tested
and monitored in our laboratories to ensure superior bearing performance.
LuBo produces different solid lubricants for both high temperature (greater than 300° F) and aquatic applications.
Please contact LuBo's application engineers for assistance with these special operating conditions.
....... 4 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Metric Size
Straight Bushings
15˚
) (
Shaft Tolerance
D
d
(d8, e7, f7)
2~8.5
10˚
R1.5~4
■ Tolerance -0.1
L -0.3
Housing : H7
Mating shaft : d8=For heavy load applications, e7=For light load applications,
f7=For high precision applications b9=For underwater or marine applications
-0.1
Product Shaft Dimension & Tolerance Length ( L -0.3 )
Code Diameter I.D O.D
ød F7 øD m6 8 10 12 15 16 20 25 30 35
+0 . 02 8 +0 . 01 8
8 8 +0 . 01 3 12 +0 . 00 7 *081208 *081210 *081212 *081215
10 10 ″ 14 ″ *101408 *101410 *101412 *101415 *101420
+0 . 03 4
12 12 +0 . 01 6 18 ″ *121810 *121812 *121815 121816 121820 121825 121830
+0 . 02 1
13 13 ″ 19 +0 . 00 8 *131910 131915 131920
14 14 ″
20 ″ *142010 *142012 *142015 *142020 *142025 *142030
15 15 ″
21 ″ *152110 *152112 152115 *152116 152120 152125 *152130
16 16 ″ 22 ″ *162210 *162212 162216 162220 162225 162230 162235
18 18 ″ 24 ″ 182415 *182416 182420 182425 182430
+0 . 04 1
20 20 +0 . 02 0 28 ″ *202815 202816 202820 202825 202830 202835
20 20 ″ 30 ″ 203016 203020 203025 203030 203035
+0 . 02 5
25 25 ″ 33 +0 . 00 9 253316 253320 253325 253330 253335
25 25 ″ 35 ″ 253516 253520 253525 253530 253535
30 30 ″ 38 ″ 303820 303825 303830 303835
30 30 ″ 40 ″ 304020 304025 304030 304035
+0 . 05 0
31.5 31.5 +0 . 02 5 40 ″ 31.54030
35 35 ″ 44 ″ 354430 354435
35 35 ″ 45 ″ 354530 354535
40 40 ″ 50 ″ 405030 405035
+0 . 03 0
40 40 ″ 55 +0 . 01 1 405530 405535
45 45 ″ 55 ″ 455530 455535
45 45 ″ 56 ″ 455630 455635
45 45 ″ 60 ″ 456030 456035
LSB 50 50 ″ 60 ″ 506030 506035
50 50 ″ 62 ″ 506230 506235
50 50 ″ 65 ″ 506530
+0 . 06 0
55 55 +0 . 03 0 70 ″
60 60 ″ 74 ″ 607430 607435
60 60 ″ 75 ″ 607530 607535
63 63 ″ 75 ″
65 65 ″ 80 ″
+0 . 03 5
70 70 ″ 85 +0 . 01 3 708535
70 70 ″ 90 ″
75 75 ″ 90 ″
75 75 ″ 95 ″
80 80 ″ 96 ″
80 80 ″ 100 ″
+0 . 07 1
90 90 +0 . 03 6 110 ″
100 100 ″ 120 ″
+0 . 04 0
110 110 ″ 130 +0 . 01 5
120 120 ″ 140 ″
+0 . 08 3
125 125 +0 . 04 3 145 ″
130 130 ″ 150 ″
140 140 ″ 160 ″
150 150 ″ 170 ″
160 160 ″ 180 ″
....... 5 .......
LuBo Industries, Inc.
LuBo #500 Series for Metric Size
.....
Straight Bushings
Housing H7
■ Materials
SP : #500SP(CAC304+Graphite)
F : #500F(GC250+Graphite)
■ Graphite Type
Blank : For General Use (SL2)
T : For High Temperature (SL1)
W : For Under Water (SL4)
-0.1
Length (L -0.3 ) Applicable
ød øD
40 50 60 70 80 100 120 130 140 150 Washer
8 12 -
10 14 LWB-10
12 18 LWB-12
13 19 LWB-13
14 20 LWB-14
15 21 LWB-15
162240 16 22 LWB-16
18 24 LWB-18
202840 *202850 20 28 LWB-20
203040 20 30 ″
253340 253350 *253360 25 33 LWB-25
253540 253550 25 35 ″
303840 303850 303860 30 38 LWB-30
304040 304050 304060 30 40 ″
31.54040 31.5 40 -
354440 354450 354460 35 44 LWB-35
354540 354550 354560 35 45 ″
405040 405050 405060 405070 *405080 40 50 LWB-40
405540 405550 405560 40 55 ″
455540 455550 455560 45 55 LWB-45
455640 455650 455660 45 56 ″
456040 456050 456060 456070 *456080 45 60 ″
506040 506050 506060 *506070 *506080 50 60 LWB-50
506240 506250 506260 506270 50 62 ″
506540 506550 506560 506570 506580 5065100 50 65 ″
557040 557050 557060 557070 55 70 LWB-55
607440 607450 607460 607470 607480 60 74 LWB-60
607540 607550 607560 607570 607580 6075100 60 75 ″
637560 637570 637580 63 75 -
658050 658060 658070 658080 65 80 LWB-65
708540 708550 708560 708570 708580 7085100 70 85 LWB-70
709050 709060 709070 709080 70 90 ″
759060 759070 759080 7590100 75 90 LWB-75
759560 759570 759580 7595100 75 95 ″
809640 809650 809660 809670 809680 8096100 8096120 80 96 LWP-80
8010040 8010050 8010060 8010070 8010080 80100100 80100120 *80100140 80 100 ″
9011060 9011080 90110100 *90110120 90 110 LWB-90
10012060 10012070 10012080 100120100 100120120 *100120140 100 120 LWB-100
11013080 110130100 110130120 110 130 -
12014080 120140100 120140120 *120140140 120 140 LWB120
125145100 125145120 125 145 -
130150100 130150130 130 150 -
140160100 140160140 140 160 -
150170100 150170150 150 170 -
160180100 160180150 160 180 -
....... 6 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Metric Size
LSBB
2~5
C0.5~1
15˚
) (
Shaft Tolerance
D
d
(d8, e7, f7)
2~8.5
10
˚
R1.5~4
-0.1
L -0.3
L
Shaft Dia. ød øD
20 25 30 40
+0.071 +0.045
20 20 +0.051 30 +0.028 203020 203025 203030 203040
+0.081 +0.055
25 25 +0.060 35 +0.034 253520 253525 253530 253540
+0.081 +0.055
30 30 +0.060 40 +0.034 304020 304025 304030 304040
+0.085 +0.055
35 35 +0.060 45 +0.034 354520 354525 354530 354540
+0.055
+0.091
50 +0.034 405020 405025 405030 405040
40 40 +0.066 +0.066
55 +0.041 405530 405540
+0.066
+0.091
55 +0.041 455530 455540
45 45 +0.066 +0.066
60 +0.041 456030 456040
+0.066
+0.091 60 +0.041 506030 506040
50 50 +0.066 +0.066
65 +0.041 506530 506540
+0.100 +0.068
55 55 +0.070 70 +0.043 557040
+0.100 +0.068
60 60 +0.070 75 +0.043 607530 607540
+0.100 +0.068
65 65 +0.070 80 +0.043
+0.080
+0.111
85 +0.051 708540
70 70 +0.081 +0.080
90 +0.051
+0.080
+0.111
90 +0.051
75 75 +0.081 +0.080
95 +0.051
+0.111 +0.080
80 80 +0.081 100 +0.051 8010040
+0.117 +0.083
90 90 +0.082 110 +0.054
+0.117 +0.083
100 100 +0.082 120 +0.054
+0.132 +0.096
120 120 +0.097 140 +0.063
+0.135 +0.096
140 140 +0.097 160 +0.065
+0.135 +0.101
160 160 +0.095 180 +0.068
....... 7 .......
LuBo Industries, Inc.
LuBo #500 Series for Metric Size
.....
Straight Bushings (#500B Bushings)
Housing H7
■ Material
#500B(CAC406+Graphite)
L
50 60 80 100 120 140 150
253550
304050 304060
354550 354560
405050 405060
405550 405560
455550 455560
456050 456060
506050 506060
506550 506560 506580
557050 557060
607550 607560 607580 6075100
658050 658060 658080
708550 708560 708580 7085100
709050 709060 709080
759060 759080 7590100
759560 759580 7595100
8010050 8010060 8010080 80100100 80100120
9011060 9011080 90110100
10012060 10012080 100120100 100120120
12014080 120140100 120140120
140160100 140160140
160180100 160180150
Product Code - d × D × L
Howto order
Example) LSBB - 20 × 30 × 2 0
....... 8 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Metric Size
Flanged Bushings
LFB C0.5
C0.5 Chamfer (Housing)
R1
.5
10
˚
) (
R 1.5 a1 Housing H7
D
d
F
a2
15
˚
(Mating shaft)
10
˚
R
0
t -0.1 b LFB
-0.1
L -0.3
■ Graphite Type
Direction of Motion Blank : For General Use (SL2)
■ Material ■ Tolerance (Sliding Motion) T : For High Temperature (SL1)
W : For Under Water (SL4)
#500SP(CAC304+Graphite) Housing : H7
Mating shaft : d8=For heavy load applications, e7=For light load applications,
f7=For high precision applications
-0.1
Flange Flange Length ( L -0.3 )
Product I.D O.D
O.D Thickness
Code ( ød) ( øD) 15 20 25 30 35 40 50 60 67.5 80 100
(ø F) (t)
+0 .0 45 + 0 .0 38
10 +0 .0 30 14 + 0 .0 23 22 2 1015 1020
+ 0. 05 0
12 + 0. 03 2 18 ″ 25 1215 1220
+0 .0 60 + 0 .0 45
13 +0 .0 42 19 + 0 .0 28 26 1315 1320
14 ″ 20 ″ 27 3 1415 1420
15 ″ 21 ″ 28 1515 1520 1525
16 ″ 22 ″ 29 1615 1620 1625
+ 0. 07 1
20 + 0. 05 0
30 ″ 40 2015 2020 2030 2040
25 + 0. 08 1
+ 0. 06 0
35 + 0 .0 55
+ 0 .0 34
45 2520 2525 2530 2540
30 ″ 40 ″ 50 3030 3040 3050
31.5 + 0 .0 85
+ 0 .0 60
40 ″ 50 31.535
35 ″ 45 ″ 60 5 3530 3540 3550
+ 0. 09 1
LFB 40 + 0. 06 6 50 ″ 65 4030 4040 4050
+ 0 .0 66
45 ″ 55 + 0 .0 41
70 4530 4540 4560
50 ″ 60 ″ 75 5030 5040 5060
+ 0 .1 00
55 + 0 .0 70 65 ″ 80 5540 5560
60 ″ 75 + 0 .0 68
+ 0 .0 43
90 6040 6050 6080
63 ″ 75 ″ 95 6367.5
7.5
+0 .1 11 + 0 .0 80
70 +0 .0 81
85 + 0 .0 51 105 7050 7080
75 ″ 90 ″ 110 7560
80 ″ 100 ″ 120 8060 8080 80100
+0 .1 17 + 0 .0 83
90 +0 .0 82 110 + 0 .0 54 130 9060 9080
10
100 ″ 120 ″ 150 10080 100100
+0 .1 32 + 0 .0 96
120 +0 .0 91 140 + 0 .0 63 170 12080 120100
....... 9 .......
LuBo Industries, Inc.
LuBo #500 Series for Metric Size
.....
Thrust Washers
LWB
b C1
P.C .D
D
C1
d
a
0
T -0.1
■ Material
Direction of Motion #500SP(CAC304+Graphite)
(Sliding Motion)
....... 10 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Metric Size
LGBF
~ R2 R2 R1~R2
R1
dH 7
Dm 6
R
D1
C1
C1
■ Material L1
#500SP(CAC304+Graphite) L
Direction of Motion
(Sliding Motion)
Product Code - d × L
How toorder
Example) LGBF - 65 × 120
....... 11 .......
LuBo Industries, Inc.
LuBo #500 Series for Metric Size
.....
Thrust Bushings
L
LTB
ℓ
2~4
Housing H7
Shaft Tolerance
R
dE 7
Dr6
A
R
1 5˚
■ Material
#500SP(CAC304+Graphite)
Direction of Motion
■ Tolerance (Sliding Motion)
Housing : H7
Mating shaft : d8=For heavy load applications, e7= For light load applications,
f7= For high precision applications
Product Code ø d ø D ø A ℓ L
+0.034
12 +0.050 18 +0.023 25 11 15
+0.032
16 22 +0.041 30 15 20
20 28 +0.028 36 20 25
+0.061
25 +0.040 33 43 25 30
+0.050
LTB 30 38 48 30 35
+0.034
40 +0.075 50 60 40 45
+0.050
+0.060
50 62 +0.041 75 49 55
+0.090 +0.062
60 +0.060 75 +0.043 90 58 65
Product Code - d × L
How to order
Example) LTB - 25 × 30
....... 12 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Metric Size
Guide Bushings
L1
L/2
M R
1~
2~4
15
3
˚
5 1
0. R
C
Dm 6
d+1
dG6
■Material
#500SP (CAC304+Graphite)
....... 13 .......
LuBo Industries, Inc.
LuBo #500 Series for Metric Size
.....
Guide Rails
LRM
60 x (n-1)
20 60 20 C1
p
C1
-0.0 1
-0.05
W
C1 D
L C1 d
S
+0.05
H1+0.02
H
■Material
0
W1 -0.05 C1
Gr #500SP (CAC304+Graphite)
Gr
LRMX +0.2
W +0.1
L (p)
+0.05
H1+0.02
H
* No Bolt holes W1 C1
Gr
Gr
■Example
....... 14 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Metric Size
Guide Blocks
LOM
+0 .1
0 H
L (P)
+0.2
Gr W +0.1
* No Bolt holes
Product Code - W × H × L
How to order
Example) LOM - 30 × 28 × 605
Lower Plates
L +0.1
T 0
* No Bolt holes
Product Code - W × L × H
How to order
Example) LPML - 40 × 10.3 × 605
....... 15 .......
LuBo Industries, Inc.
LuBo #500 Series for Metric Size
.....
Sliding Plates
6
W
a b a 7 4-C1
4-C1
W/2
L W/2
1 0 ±0. 02 5
W=35, 50
1 6 4-R2
6
W
a b c d e a 9
W/ 2
4-C1
L ■ Material
#500SP (CAC304 + graphite)
15
W=75
1 0 ±0 .0 2 5
3.5
16 R5
4-
45
W
2
a b c d e a 4-C1
9
15
....... 16 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Inch Size
Straight Bushings
HBN
C .02~.04 .08~.20
15°
d8
e7
Shaft f 7
I.D O.D
.08~.33
10 °
R .06~.16
L
■ Tolerance
Mating shaft : d8=For heavy load applications,
e7=For light load applications, f7=For high precision applications
Dimension Dimension
Product Code Product Code
I.D O.D Length I.D O.D Le ngth
HBN-081208 1/2 HBN-202620 1 1/4
HBN-081210 5/8 HBN-202622 1 3/8
HBN-081212 3/4 HBN-202624 1 1/2
1/2 3/4
HBN-081214 7/8 HBN-202628 1 1/4 1 5/8 1 3/4
HBN-081216 1 HBN-202630 1 7/8
HBN-081220 1 1/4 HBN-202632 2
HBN-101410 5/8 HBN-202648 3
HBN-101412 3/4 HBN-243216 1
5/8 7/8
HBN-101416 1 HBN-243220 1 1/4
HBN-101424 1/2 HBN-243222 1 3/8
HBN-121810 5/8 HBN-243224 1 1/2
HBN-121812 3/4 HBN-243228 1 1/2 2 1 3/4
HBN-121814 7/8 HBN-243230 1 7/8
3/4 1 1/8
HBN-121816 1 HBN-243240 2
HBN-121822 1 3/8 HBN-243248 3
HBN-121824 1 1/2 HBN-243264 4
HBN-142012 3/4 HBN-283620 1 1/4
HBN-142016 1 HBN-283624 1 1/2
HBN-142020 7/8 1 1/4 1 1/4 HBN-283628 1 3/4
HBN-142022 1 3/8 HBN-283632 2
1 3/4 2 1/4
HBN-142024 1 1/2 HBN-283640 2 1/2
HBN-162212 3/4 HBN-283648 3
HBN-162216 1 HBN-283656 3 1/2
HBN-162220 1 1/4 HBN-283664 4
HBN-162222 1 3/8 HBN-324020 1 1/4
1 3/8
HBN-162224 1 1/2 HBN-324024 1 1/2
HBN-162228 1 3/4 HBN-324032 2
1
HBN-162232 2 HBN-324040 2 2 1/2 2 1/2
HBN-162248 3 HBN-324044 2 3/4
HBN-162412 3/4 HBN-324048 3
HBN-162416 1 HBN-324062 3 7/8
1 1/2
HBN-162424 1 1/2 HBN-364424 1 1/2
HBN-162432 2 HBN-364432 2 1/4 2 3/4 2
HBN-202616 1 1/4 1 5/8 1 HBN-364440 2 1/2
....... 17 .......
LuBo Industries, Inc.
LuBo #500 Series for Inch Size
.....
Straight Bushings
HBN
Thrust Washer
Housing
■ Materials
Bushing (HBN) Copper Alloy (C86300) with
Graphite Plugs
Dimension Dimension
Product Code Product Code
I.D O.D Length I.D O.D Length
HBN-364448 2 1/4 2 3/4 3 HBN-486040 2 1/2
HBN-404824 1 1/2 HBN-486048 3
3 3 3/4
HBN-404832 3 2 HBN-486056 3 1/2
HBN-404848 3 HBN-486078 4 7/8
HBN-405224 2 1/2 1 1/2 HBN-566632 2
HBN-405232 2 HBN-566648 3 1/2 4 1/8 3
3 1/4
HBN-405248 3 HBN-566664 4
HBN-405278 4 7/8 HBN-647632 2
HBN-445424 1 1/2 HBN-647648 4 4 3/4 3
HBN-445432 2 HBN-647664 4
2 3/4 3 3/8
HBN-445440 2 1/2 HBN-728648 3
HBN-445448 3 HBN-728664 4 1/2 5 3/8 4
HBN-485832 2 HBN-728680 5
HBN-485840 2 1/2 HBN-809648 3
3 5/8
HBN-485848 3 3 HBN-809664 4
5 6
HBN-485856 3 1/2 HBN-809680 5
HBN-486032 3 3/4 2 HBN-809696 6
....... 18 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Inch Size
Shoulder Bushings
LSBN L +.00
-.03
3/16(1/2)
+.00
B -1/32 D A
■ Materials
Copper Alloy (C86300) with * ( ) is Only for I.D. 3.
Graphite Plugs
Product Code
How to order
Example) LSBN 750-07
....... 19 .......
LuBo Industries, Inc.
.....
Ejector Bushings
LEBGN
C L +.00
-.03
B +.00
L 1-.03
D 3/16 ■ Materials
Copper Alloy (C86300) with
Unless otherwise noted, tolerances are ± .010 (.25mm)
Graphite Plugs
Product Code
How to order
Example) LEBGN 1250
Thrust
Thrust Washers
Washers
C1
TWN-08 1/2 1 1/2 1 1/16
TWN-10 5/8 1 3/4 1 5/16 1/8 1/8
TWN-12 3/4 2 1 1/2 C1
C.D
TWN-32 2 4 3 3/16
TWN-36 2 1/4 4 1/2 3 5/8 1/4
TWN-40 2 1/2 4 3/4 3 3/4 5/16
TWN-44 2 3/4 5 1/8 4 1/8
■ Materials
TWN-48 3 5 1/2 4 1/2
5/16 Copper Alloy (C86300) with Graphite Plugs
TWN-56 3 1/2 6 3/4 5 1/2 3/8
TWN-64 4 7 1/2 6 1/4 4
TWN-72 4 1/2 7 3/4 6 3/8 Product Code
How toorder
3/8 1/2
TWN-80 5 8 6 3/4 Example) TWN-32
....... 20 .......
LuBo Industries, Inc.
..... LuBo #500 Series for Inch Size
Wear Strips
LBWN
A B C D E F L A B C L
G G
W
A-A
H
C'SUNK FOR FLAT HD. SCREW
W
B-B
■ Materials A B C D E F L
- Copper Alloy(C86300)
with Graphite Plugs Thick ness Counter Bore
G
- Copper Alloy(C86300) 2 1/4 .250 For 1/4" Flat Hd. Scr.
without Graphite Plugs 3 3/8 .375 For 1/4" Soc. Hd. Scr.
H
4 1/2 .500 For 5/16" Soc. Hd. Scr.
■ Note W
5 5/8 .625 For 5/16" Soc. Hd. Scr. C-C
Width and length of wearstrip
determines hole pattern.
Regardless of thickness.
....... 21 .......
LuBo Industries, Inc.
LuBo #500 Series for Inch Size
.....
Wear Strips
Product Code Width Length Product Code Width Length Product Code Width Length Product Code Width Length
LBWN28-32G 1.00 4.00 LBWN220-32G 2.50 4.00 LBWN38-32G 1.00 4.00 LBWN320-32G 2.50 4.00
LBWN28-40G 1.00 5.00 LBWN220-40G 2.50 5.00 LBWN38-40G 1.00 5.00 LBWN320-40G 2.50 5.00
LBWN28-48G 1.00 6.00 LBWN220-48G 2.50 6.00 LBWN38-48G 1.00 6.00 LBWN320-48G 2.50 6.00
LBWN28-64G 1.00 8.00 LBWN220-64G 2.50 8.00 LBWN38-64G 1.00 8.00 LBWN320-64G 2.50 8.00
LBWN28-80G 1.00 10.00 LBWN220-80G 2.50 10.00 LBWN38-80G 1.00 10.00 LBWN320-80G 2.50 10.00
LBWN28-96G 1.00 12.00 LBWN220-96G 2.50 12.00 LBWN38-96G 1.00 12.00 LBWN320-96G 2.50 12.00
LBWN212-32G 1.50 4.00 LBWN224-32G 3.00 4.00 LBWN312-32G 1.50 4.00 LBWN324-32G 3.00 4.00
LBWN212-40G 1.50 5.00 LBWN224-40G 3.00 5.00 LBWN312-40G 1.50 5.00 LBWN324-40G 3.00 5.00
LBWN212-48G 1.50 6.00 LBWN224-48G 3.00 6.00 LBWN312-48G 1.50 6.00 LBWN324-48G 3.00 6.00
LBWN212-64G 1.50 8.00 LBWN224-64G 3.00 8.00 LBWN312-64G 1.50 8.00 LBWN324-64G 3.00 8.00
LBWN212-80G 1.50 10.00 LBWN224-80G 3.00 10.00 LBWN312-80G 1.50 10.00 LBWN324-80G 3.00 10.00
LBWN212-96G 1.50 12.00 LBWN224-96G 3.00 12.00 LBWN312-96G 1.50 12.00 LBWN324-96G 3.00 12.00
LBWN216-32G 2.00 4.00 LBWN232-32G 4.00 4.00 LBWN316-32G 2.00 4.00 LBWN332-32G 4.00 4.00
LBWN216-40G 2.00 5.00 LBWN232-40G 4.00 5.00 LBWN316-40G 2.00 5.00 LBWN332-40G 4.00 5.00
LBWN216-48G 2.00 6.00 LBWN232-48G 4.00 6.00 LBWN316-48G 2.00 6.00 LBWN332-48G 4.00 6.00
LBWN216-64G 2.00 8.00 LBWN232-64G 4.00 8.00 LBWN316-64G 2.00 8.00 LBWN332-64G 4.00 8.00
LBWN216-80G 2.00 10.00 LBWN232-80G 4.00 10.00 LBWN316-80G 2.00 10.00 LBWN332-80G 4.00 10.00
LBWN216-96G 2.00 12.00 LBWN232-96G 4.00 12.00 LBWN316-96G 2.00 12.00 LBWN332-96G 4.00 12.00
Product Code Width Length Product Code Width Length Product Code Width Length Product Code Width Length
LBWN412-24G 1.50 3.00 LBWN420-48G 2.50 6.00 LBWN512-24G 1.50 3.00 LBWN520-48G 2.50 6.00
LBWN412-32G 1.50 4.00 LBWN420-64G 2.50 8.00 LBWN512-32G 1.50 4.00 LBWN520-64G 2.50 8.00
LBWN412-40G 1.50 5.00 LBWN420-80G 2.50 10.00 LBWN512-40G 1.50 5.00 LBWN520-80G 2.50 10.00
LBWN412-48G 1.50 6.00 LBWN420-96G 2.50 12.00 LBWN512-48G 1.50 6.00 LBWN520-96G 2.50 12.00
LBWN412-64G 1.50 8.00 LBWN424-24G 3.00 3.00 LBWN512-64G 1.50 8.00 LBWN520-24G 3.00 3.00
LBWN412-80G 1.50 10.00 LBWN424-32G 3.00 4.00 LBWN512-80G 1.50 10.00 LBWN524-32G 3.00 4.00
LBWN412-96G 1.50 12.00 LBWN424-40G 3.00 5.00 LBWN512-96G 1.50 12.00 LBWN524-40G 3.00 5.00
LBWN416-24G 2.00 3.00 LBWN424-48G 3.00 6.00 LBWN516-24G 2.00 3.00 LBWN524-48G 3.00 6.00
LBWN416-32G 2.00 4.00 LBWN424-64G 3.00 8.00 LBWN516-32G 2.00 4.00 LBWN524-64G 3.00 8.00
LBWN416-40G 2.00 5.00 LBWN424-80G 3.00 10.00 LBWN516-40G 2.00 5.00 LBWN524-80G 3.00 10.00
LBWN416-48G 2.00 6.00 LBWN424-96G 3.00 12.00 LBWN516-48G 2.00 6.00 LBWN524-96G 3.00 12.00
LBWN416-64G 2.00 8.00 LBWN432-32G 4.00 4.00 LBWN516-64G 2.00 8.00 LBWN532-32G 4.00 4.00
LBWN416-80G 2.00 10.00 LBWN432-40G 4.00 5.00 LBWN516-80G 2.00 10.00 LBWN532-40G 4.00 5.00
LBWN416-96G 2.00 12.00 LBWN432-48G 4.00 6.00 LBWN516-96G 2.00 12.00 LBWN532-48G 4.00 6.00
LBWN420-24G 2.50 3.00 LBWN432-64G 4.00 8.00 LBWN520-24G 2.50 3.00 LBWN532-64G 4.00 8.00
LBWN420-32G 2.50 4.00 LBWN432-80G 4.00 10.00 LBWN520-32G 2.50 4.00 LBWN532-80G 4.00 10.00
LBWN420-40G 2.50 5.00 LBWN432-96G 4.00 12.00 LBWN520-40G 2.50 5.00 LBWN532-96G 4.00 12.00
Product Code
Howto order
Example) LBWN416-48NG
- First number denotes thickness (In eighths of an inch)
- Denotes width (In eighths of an inch)
- Denotes Length (In eighths of an inch)
- Add the suffix 'N' for undrilled
- Add the suffix 'G' for self lubrication (Graphite plugs)
....... 22 .......
LuBo Industries, Inc.
..... LuBo #500 Self-Lubricating Spherical Bearings
1. LuBo #500 self-aligning, self-lubricating bearings consist of an inner and an outer ring with curved mating surfaces.
Either or both of these curved surfaces can be dry-lubricated.
2. Three inner ring material choices are available depending on the application conditions : Copper Alloy, Bronze, and
Cast Iron. Solid lubricant selection is also based on the application conditions.
3. The outer ring is made of carbon steel bearingwith a protective coa ting for corrosion resistance. Upon request, LuBo
Industries recommends coating the inner surface of the outer ring with MoS 2 for longer bearing life. (See MoS 2 Dry
Coating on page 25.)
42.)
4. Specials to Customer's Specifications : LuBo produces non-standard, angular contact, self-lubricating spherical
bearings in both metric and inch dimensions.
5. A number of factors must be considered when ordering customized spherical bearings, such as the magnitude and
direction of applied loads, operating temperature and other environmental conditions, presence of corrosive fluids,
etc.
Careful evaluation of these factors is critical to the proper selection of bearing materials and lubricants.
Please contact LuBo's application engineers for assistance with your applications.
....... 23 .......
LuBo Industries, Inc.
LuBo #500 Self-Lubricating Spherical Bearings
.....
Materials
0
① Outer Ring : AISI 1045 (SM45C) + MoS 2 Coating
B -0.2
C
0
-0.2
1 ② Inner Ring : #500SP (Copper Alloy + Graphite)
r
r
Mating Shaft and Housing (Recommended)
General Load Heavy Load
S
r e
he
Shaft Housing Shaft Housing
dH7
Dh6
Sp
g6 H7 n6 N7
a
b
Product Code - d × D
Howto order
Example) LUBS - 15 × 26
Typical Applications
● Construction Machinery ● Agricultural Machinery ● Mining Equipment ● Logging Equipment
● Transportation Equipment ● Industrial Machinery ● Off-Highway Vehicles
....... 24 .......
LuBo Industries, Inc.
.....
An additional coating of MoS 2 dry lubricant on sliding surface provides extra resistance against wear, heavy loads,
high temperature, and chemical breakdown.
What is MoS 2?
MoS 2 is a fine, black powder similar to graphite. MoS 2 has the following features:
1. Physical Properties
2. Characteristics
● Temperature Resistance : Service range in ambient air (-680 ~ 1,300 ° F)
● High-Load Resistance : Endures up to 66.8kpsi (33.4Ton/cm2 )
● Low Frictional Coefficient : Increasing the load causes the frictional coefficient to decrease.
Dynamic frictional coefficient is close to 0.02~0.04
● Chemical Resistance : Safe for use with water, all kinds of solvents, acids, and alkalies.
Load
Coated
Contact
....... 25 .......
LuBo Industries, Inc.