Professional Documents
Culture Documents
then the measuring machine uncertainty should be no more than one-fifth (ideally one- -0.004
tenth) of that, i.e. 4μm. This means that with a general-purpose CMM, when the measured -0.006
length exceeds 375 mm, machine uncertainty exceeds one-fifth of the dimension tolerance -0.008
in this case. In contrast, as shown in the figure on the right, with the CRYSTA-Apex S the Measuring length (mm)
Error (µm)
26°C
0.0 20°C
workpiece temperature compensation scheme used on the CRYSTA-Apex S -2.0 E0,MPE accuracy specification limits at 20 ± 2 °C
-4.0
gives markedly superior results compared to systems that only compensate for -6.0
E0,MPE accuracy specification limits at 16 to 26 °C
0 100 200 300 400 500 600 700
scale temperature. Controller Workpiece Measured length (mm)
Temperature sensor
(for Workpiece)
Temperature
measuring and
compensating
device
CRYSTA-Apex S 544
CRYSTA-Apex S 776
2
CRYSTA-Apex S Series
High-speed, high-acceleration drive
Effect of higher speed and acceleration on drive distance
500
The CRYSTA-Apex S Series offers a maximum drive speed of 519 mm/s and a maximum 450
acceleration of 2,309 mm/s2 [500/700/900 Series], resulting in an increase of almost 100 mm in 400
drive distance in one second, when compared with general-purpose CNC coordinate measuring 350
CRYSTA-Apex S 9106
CRYSTA-Apex S 122010
3
CRYSTA-Apex S 500 Series Specifications*
Model No. CRYSTA-Apex S 544 CRYSTA-Apex S 574
CRYSTA-Apex S range
X axis
Measuring Y axis
Z axis
400 mm
500 mm
400 mm
700 mm
CRYSTA-Apex S 500 Series Dimensions (unit: mm) Installation floor space (unit: mm)
Space for maintenance
Forbidden zone
2582 200
900 1082 600
200
200 722
800
AC IN 3m
1585
2m 5m
40
145 Z:400
2185
X:500 Y CRYSTA-Apex S
500
D
B
Air hose
A
8m
150
750
650~850
600
1000
ø700 r) Option
F.L (caste Auxiliary legs
590 E3
(Supporting points) (Supporting points) 100 785 Data-processing System Control panel
100
700
860 (Workpiece loading area)
525
9-M8×1.25
400 350
200 175
0 0
Front Front
96
96
59 59
CRYSTA-Apex S CRYSTA-Apex S
Y cover Y cover
0
574
125
250
375
544
250
500
500
4
CRYSTA-Apex S 700 Series Specifications*
Model No. CRYSTA-Apex S 776 CRYSTA-Apex S 7106
CRYSTA-Apex S range
X axis
Measuring Y axis
Z axis
700 mm
700 mm
600 mm
1000 mm
CRYSTA-Apex S 700 Series Dimensions (unit: mm) Installation floor space (unit: mm)
Forbidden zone Space for maintenance
1470 A 2970 200
900 1470 600
200
405 800
600
AC IN 3m
CRYSTA-Apex S
2730
AC IN 2m 5m 700
B
X : 700 Y
D
A
Z : 600
(5m)
C
250
8m Option
700
100 650~850
1000
AC-IN
AIR-IN F.L ø700 ) Auxiliary legs
r
800 (Supporting points) 225 B C (Supporting points) (caste Support legs
1430 100 785 Data-processing System Control panel
1000
11-M8×1.25
700 750
467 500
350
233 * マウステーブル使用時:
250 850mm
2モニタ専用ラック使用時:1000mm
0 0
175.5 175.5
F ront F ront
CRYSTA-Apex S Y cover CRYSTA-Apex S
0
175
350
525
700
87.5
0
175
350
525
700
Y cover
87.5
5
CRYSTA-Apex S 900 Series Specifications*
Model No. 9106CRYSTA-Apex S CRYSTA-Apex S CRYSTA-Apex S
(Z600)/9108 (Z800) 9166 (Z600)/9168 (Z800) 9206 (Z600)/9208 (Z800)
X axis 900 mm
CRYSTA-Apex S
Measuring Y axis 1000 mm 1600 mm 2000 mm
range
Z axis 600 mm / 800 mm
Resolution 0.0001 mm (0.1 μm)
900 Series
Guide method Air bearings on each axis
8 - 300 mm/s (CNC mode), max. speed: 519 mm/s
Drive speed 0 - 80 mm/s (J/S Mode: High Speed)
0 - 3 mm/s (J/S Mode: Low Speed)
0.05 mm/s (J/S Mode: Fine Speed)
Max. measuring speed 8 mm/s (3 mm/s for Type Z800)
Max. drive acceleration Each axis: 1,333 mm/s² (1,000 mm/s² Type Z800), max. com-
bined acceleration 2,309 mm/s² (1,732 mm/s² Type Z800)
Maximum height 800 mm (Z=600 mm) / 1000 mm (Z=800 mm)
Workpiece
Maximum mass 1200 kg 1500 kg 1800 kg
Mass (including the control 2231 kg (Z=600 mm) 2868 kg (Z=600 mm) 3912 kg (Z=600 mm)
device and installation platform) 2261 kg (Z=800 mm) 2898 kg (Z=800 mm) 3942 kg (Z=800 mm)
Air Pressure 0.4 MPa
supply Consumption 60 L/min under normal conditions (air source: 120 L/min)
* While the appearance of the natural stone measuring table varies according to the
source, the high stability for which this material is known can always be relied upon.
CRYSTA-Apex S 900 Series Accuracy unit: μm
Repeatability Max. permissible single
Probe Max. permissible length measurement error range of E0 stylus form error
used ISO 10360-2:2009 ISO 10360-5: 2010
SP25M/ E0, MPE=1.7+3L/1000 (Temperature environment 1)
E150, MPE=1.7+3L/1000 (Temperature environment 1)
MPP310Q/ R0, MPL=1.3 PFTU,MPE=1.7
SP80 E0, MPE=1.7+4L/1000 (Temperature environment 2)
E150, MPE=1.7+4L/1000 (Temperature environment 2)
CRYSTA-Apex S 900 Series Installation Temperature E0, MPE=1.9+3L/1000 (Temperature environment 1)
Temperature Temperature E150, MPE=2.4+3L/1000 (Temperature environment 1)
TP200 R0, MPL=1.9 PFTU,MPE=1.9
environment 1 environment 2 E0, MPE=1.9+4L/1000 (Temperature environment 2)
Temperature Range 20±2 °C 16 - 26 °C E150, MPE=2.4+4L/1000 (Temperature environment 2)
Limits within E0, MPE=2.2+3L/1000 (Temperature environment 1)
which accuracy Rate of 2 °C per hour or less 2 °C per hour or less
change 2 °C in 24 hours or less 5 °C in 24 hours or less E150, MPE=2.7+3L/1000 (Temperature environment 1)
is guaranteed TP20 R0, MPL=2.2 PFTU,MPE=2.2
Gradient 1 °C per hour or less 1 °C per hour or less E0, MPE=2.2+4L/1000 (Temperature environment 2)
E150, MPE=2.7+4L/1000 (Temperature environment 2)
* L=Measuring length (unit: mm)
Note: This machine incorporates a main unit Startup system (relocation detection system), which * Table at left defines temperature environments 1 and 2
disables operation when an unexpected vibration is applied or the machine is relocated. Be sure to
contact your nearest Mitutoyo Sales Office prior to relocating this machine after initial installation. CRYSTA-Apex S 900 Series Accuracy unit: μm
Probe used Max. permissible scanning probing error (MPETHP)
ISO 10360-4: 2000
CRYSTA-Apex S 900 Series Dimensions (unit: mm) SP25M (Stylus: ø4 X 50 mm) 2.3 (50s) [2.3 (60s) for Z800 model]
1670 MPP310Q (Stylus: ø4 X 18 mm) 1.8 (80s)
SP80 (Stylus: ø4 X 50 mm) 2.0 (50s) [2.3 (60s) for Z800 model]
405 1000
600
X : 900 Y
A
B
Z
52
82
AC IN 3m CRYSTA-Apex S
D
B
700
900
A
2m 5m main unit
F.L Air hose
1000 (Supporting points) 225 E F (Supporting points) (5m)
C
1670 D Option
8m
100 650~850
Auxiliary legs
1000
1600
2320 (Workpiece loading area)
1500
1334
1250
1720 (Workpiece loading area)
13-M8×1.25
1067
1000 1000
800
750 750
87.5
0
225
450
675
900
87.5
0
225
450
675
900
87.5
6
CRYSTA-Apex S 1200 Series Specifications*
CRYSTA-Apex S CRYSTA-Apex S CRYSTA-Apex S
Model No. 121210 122010 123010
X axis 1200mm
CRYSTA-Apex S
Measuring Y axis 1200mm 2000mm 3000mm
range
Z axis 1000mm
Resolution 0.0001mm (0.1μm)
1200 Series
Guide method Air bearings on each axis
8 - 400 mm/s (CNC mode), max. speed: 693 mm/s
Drive speed 0 - 80 mm/s (J/S Mode: High Speed)
0 - 3 mm/s (J/S Mode: Low Speed)
0.05 mm/s (J/S Mode: Fine Speed)
Max. measuring speed 5mm/s
Max. drive acceleration Each axis: 1,000 mm/s², max. combined acceleration 1,732 mm/s²
Maximum height 1200 mm
Workpiece
Maximum mass 2000 kg 2500 kg 3000 kg
Mass (including the control 4050 kg 6150 kg 9110 kg
device and installation platform)
Pressure 0.4MPa
Air supply
Consumption 100 L/min under normal conditions (air source: 150 L/min)
* While the appearance of the natural stone measuring table varies according to the
source, the high stability for which this material is known can always be relied upon.
CRYSTA-Apex S 1200 Series Accuracy unit: μm
Max. permissible length measurement error Repeatability Max. permissible single
Probe range of E0 stylus form error
used
ISO 10360-2:2009 ISO 10360-5: 2010
SP25M/ E0, MPE=2.3+3L/1000 (Temperature environment 1)
E150, MPE=2.3+3L/1000 (Temperature environment 1)
MPP310Q/ R0, MPL=1.9 PFTU,MPE=2.0
SP80 E0, MPE=2.3+4L/1000 (Temperature environment 2)
E150, MPE=2.3+4L/1000 (Temperature environment 2)
E0, MPE=2.5+3L/1000 (Temperature environment 1)
E150, MPE=3.0+3L/1000 (Temperature environment 1)
TP200 R0, MPL=2.0 PFTU,MPE=2.2
E0, MPE=2.5+4L/1000 (Temperature environment 2)
E150, MPE=3.0+4L/1000 (Temperature environment 2)
CRYSTA-Apex S 1200 Series Installation Temperature E0, MPE=2.8+3L/1000 (Temperature environment 1)
E150, MPE=3.3+3L/1000 (Temperature environment 1)
Temperature Temperature TP20 R0, MPL=2.4 PFTU,MPE=2.6
E0, MPE=2.8+4L/1000 (Temperature environment 2)
environment 1 environment 2 E150, MPE=3.3+4L/1000 (Temperature environment 2)
Temperature Range 20±2 °C 16 - 26 °C * L=Measuring length (unit: mm)
Limits within
which accuracy Rate of 2 °C per hour or less 2 °C per hour or less * Table at left defines temperature environments 1 and 2
change 2 °C in 24 hours or less 5 °C in 24 hours or less
is guaranteed CRYSTA-Apex S 1200 Series Accuracy unit: μm
Gradient 1 °C per hour or less 1 °C per hour or less
Max. permissible scanning probing error (MPETHP)
Probe used ISO 10360-4: 2000
Note: This machine incorporates a main unit Startup system (relocation detection system), which SP25M (Stylus: ø4 X 50 mm) 2.8 (50s)
disables operation when an unexpected vibration is applied or the machine is relocated. Be sure to MPP310Q (Stylus: ø4 X 18 mm) 2.3 (80s)
contact your nearest Mitutoyo Sales Office prior to relocating this machine after initial installation.
SP80 (Stylus: ø4 X 50 mm) 2.5 (50s)
CRYSTA-Apex S 1200 Series Dimensions (unit: mm) Installation floor space (unit: mm)
2200 Space for maintenance
Forbidden zone
3700 200
900 2200 600
200
595 1345
600
3m
3645
AC IN 3m
B
main unit
A
2m
Z: 1000
X: 1200 Y
487 487 5m
888
C
UC440
52
Option
8m
592
100 650~850
600
Auxiliary legs
1000
ø700
F.L (caster) Support legs
1345 (Supporting points) 200 C B (Supporting points) 100 785 Data-processing System Control panel
2140 A
2000
1600
2165 (Workpiece loading area)
16-M8×1.25 1600
1200 1200
1200
800 800
800
400 400
400
0 0
273 273 0
Front 273
Front
CRYSTA-Apex S CRYSTA-Apex S Front
CRYSTA-Apex S
100
0
400
800
1200
100
0
400
800
1200
400
800
1200
7
Group of options that enable various kinds of
measurements
CAT1000S
(freeform surface evaluation program)
Checks and compares the workpiece with the CAD data containing freeform
surfaces and directly outputs the results in the form of CAD data in various
formats. Software to directly convert from/to various types of CAD data is
available as an option.
8
GEOPAK (high-functionality
general-purpose measurement
program)
This module is the heart of the
MCOSMOS software system and is
used to measure and analyze geometric
elements. All the functions are provided
by icons or pull-down menus, so even
novices can promptly select desired
functions. Its main features include easier
viewing of measuring procedures and
results such as realtime graphic display VISIONPAK
of measurement results and a function (vision measurement program)
for direct call-up of elements from results This program controls QVP and performs various
graphics. computational analyses on captured images.
GEARPAK
(gear eval uation program)
For evaluating the most types of involute gears.
SurfaceDeveloper
This program generates free-form surface models
from multi-sectional contour data.
Probe center cloud data Real triangular mesh model CAD data
9
Group of options that enable various kinds of
measurements
SurfaceMeasure606/610/1010/606T/201FS
(non-contact laser probe)
A lightweight, high-performance, non-contact probe developed for CNC
coordinate measuring machines. Powder spray-less measurement has been
achieved through automatic setting of appropriate laser intensity and camera
sensitivity according to environment or material, providing a simpler and more
comfortable laser scanning environment.
SURFTEST PROBE
(Probe for surface roughness measurement)
SURFTEST PROBE is a probe foe measuring surface roughness that can be equipped
with a CNC coordinate measuring machine. With auto-probe change system, it can
automatically exchange with a touch trigger probe or a scanning probe (SPM25M).
This provides ability to perform combined automatic measurement of dimension,
form, and surface roughness measurement.
Mitutoyo will meet various kinds of requests for measurement by providing
dedicated software and wide range of optional detectors.
10
MPP-310Q (scanning probe)
Probe that collects coordinate values (point cloud data) at
high accuracy by moving at speeds of up to of 120 mm/s
while in contact with the workpiece. Because MPP-310Q
can also be used with the rotary table (MRT320) for
synchronous scanning, it is effective for measuring gears,
blades, ball screws, cylindrical cams, etc.
MRT320
11
047 1703(1)B-(TX)NE, Printed in Japan
Coordinate Measuring Machines Vision Measuring Systems Form Measurement Optical Measuring
Whatever your challenges are, Mitutoyo
supports you from start to finish.
http://www.mitutoyo.co.jp/global.html
Mitutoyo Corporation
Our products are classified as regulated items under Japanese Foreign Exchange and Foreign Trade Law. Please consult us in advance if
you wish to export our products to any other country. 20-1, Sakado 1-Chome,
If the purchased product is exported, even though it is not a regulated item (Catch-All controls item), the customer service available for
Takatsu-ku, Kawasaki-shi,
that product may be affected. If you have any questions, please consult your local Mitutoyo sales office.
Kanagawa 213-8533, Japan
Note: Product illustrations are without obligation. Product descriptions, in particular any and all technical
specifications, are only binding when explicitly agreed upon. T +81 (0) 44 813-8230
MITUTOYO and MiCAT are either registered trademarks or trademarks of Mitutoyo Corp. in Japan and/or other countries/regions.
F +81 (0) 44 813-8231
Other product, company and brand names mentioned herein are for identification purposes only and may be the
trademarks of their respective holders. http://www.mitutoyo.co.jp