Professional Documents
Culture Documents
MULTICHANNEL
A A1
A2
B C
J
E
H
A B C D E F
MULTICHANNEL
4 5 6
4A 4B 4C 4D 5A
G
J
5B
J
MULTICHANNEL
1 2
MULTICHANNEL
The pipette design enables the user to perform the recali- button (Fig. 1A2) or the adjustment knob (Fig. 1B) increas-
bration process according to the rules presented in sec- ing the value until the lower figure wheel comes 1/3 of a
tion 5. turn beyond the required setting and then slowly backward
until the setting reaches the desired volume. Make sure not
2 - SETTING THE VOLUME to pass the setting value.
The setting of the volume of the aspirated liguid can be If the knob is accidentally turned too far, the process
done either by the pipetting pushbutton knob (Fig. 1A2) must be repeated. The desired volume must always be
or by the adjustment knob (Fig. 1B). The volume adjust- set from the higher value in the order of decreasing value.
ment can be performed when the locking ring is set in Following volume adjustment, set the locking ring into the
the lower position (Fig. 5A). When the desired volume is upper position, thus locking the knob and preventing
selected, the locking ring should be set in the upper accidental volume change.
position (Fig. 5B).
The volume shown by the counter is represented by 3 - METHOD OF PIPETTING
three digits, which should be read from top to bottom.
Fit the tips onto cones of the multichannel module. In
Typical meter readings are shown in the following table:
order to put tips on the multichannel cones hold the
Model
Counter Set Basic pipette vertically and press it against the tips in the rack
readings volume degree box, until the cones retreat about 1.5 mm into the multi-
0
channel module. The suspension system of the cones
BPPE-10
3 3.5 μl 0.02 μl ensures even and tight sealing of tips. The pipette does
BPPT-10 not need to be rolled back and forth to seal the tips
5
tightly. The liquid aspirated into the tips should not flow
BPPE-50 0 out by gravity from properly fixed tips. While holding the
6 6.5 μl 0.10 μl pipette in a vertical position, tips should be immersed in
BPPT-50
5 the liquid to a depth of 2-4 mm, and flushed once by
drawing a dose of liquid and dispensing it out with slow
BPPE-200 0
8 85.0 μl 0.20 μl and steady movement. Next, still holding the pipette ver-
BPPT-200 tically, the operator should press the pipetting button
5
until the first resistance point is felt, and immerse the tips
BPPE-300 2 in the liquid to the depth of 2-4 mm, (Fig. 3B). Releasing
5 250.0 μl 1.0 μl the pipetting button with a slow and uniform movement
BPPT-300
0 during 2-3 seconds, the liquid should be drawn into the
tips, (Fig. 3B) which should then be lifted above the liq-
To attain the maximum accuracy, set volume must be uid’s surface. The pipette should next be positioned at an
approached from a higher value by diminishing counter angle of 10-45 degrees in relation to inner walls of desti-
readings. nation vessels and tips should be emptied by pressing
• If the desired volume is lower than set volume shown the pipetting button slowly until the first resistance point is
by the counter, the operator should turn the pipetting felt, (Fig. 3C). After waiting second, the pipetting button
pushbutton (Fig. 1A2) or the adjustment knob (Fig. 1B) should be pressed to the second resistance point in
to the direction diminishing counter readings to the order to expell remaining liquid, (Fig. 3D). Then tips
required volume. Before achieving the required volume should be lifted out from the vessels while maintaining
slowly rotate the knob and observe carefully diminish- contact between the ends of the tips and the inner walls
ing reading to avoid accidentally passing the setting of the vessel until the pipetting button has been relased,
value. (Fig. 3E). Finally, pressing the ejector button, the opera-
• If the desired volume is higher than set volume shown by tor should separate the tips from multichannel module’s
the counter, the operator should turn the pipetting push- cones, (Fig. 3F).
3 4
MULTICHANNEL
BPPE-50
BPPE-200
6 - CLEANING AND STERILIZATION BPPT-50
P1000-200-R, 200 μl tips, racked
BPPT-200
Cleaning BPPE-300
P1000-300-R, 300 μl tips, racked
BPPT-300
External surfaces of the pipetting pushbutton, the ejector
button, the handgrip, shaft and the adjustment knob may Pipettor Stand Choices
be cleaned using a cloth dampened in isopropyl alcohol. BPPE, BPPT P3989 Universal linear stand
7 8
MULTICHANNEL
8 - SPARE PARTS
The spare parts for multichannel in, (Fig. 1, 4, 5):
A: Pipetting pushbutton A1: Pushbutton A2: Knob
B: Adjustment knob
C: Ejector button
D: Piston’s assembly
E: Tip cone
F: Ejector
G: Calibration key
J: Locking ring