Professional Documents
Culture Documents
Generic RAN Information Management (RIM) procedures support the exchange of information, via
the core network, between peer application entities located in a GERAN, in a UTRAN or in an E-
UTRAN access network.
Feature LTE1196 introduces possibility to define “UTRA SI” RIM application to transfer up-to-date
System Information of WCDMA neighbor cells from remote RNC to local eNB.
After reception to eNB, they can be used to populate WCDMA System Information for redirection to
WCDMA procedure.
RIM feature is introduced to allow the eNodeB to receive WCDMA SIB information from RNC without
the need for configuration of WCDMA SIBs by operator ( RL30 CRL0526- SI for CSFB to WCDMA give
such possibility ).
With introduction of LTE1196 the received WCDMA SIB are used during enhanced UE Context
Release with Redirect to WCDMA for CS fallback and/or the 'normal' redirect (CRL0526 will not be
supported anymore).
Voice call setup delays are expected to be shorter in the “CSFB to 3G via Redirect” scenario if the
RIM feature is activated and the UE supports it. Since the UE does not have to read all System
Information messages during 3G RAN access, the added delay by CSFB becomes shorter.
- one or more PLMN Ids may need to be configured with the LNMME parameter
rimReachablePLMNList if a MME supports routing of RIM PDUs to more PLMN Ids
as indicated in the list of served PLMN Ids.
W7I:FEA,FULL:FEA=3206,;
FEATURE INFORMATION:----------------------------------------------
< ZWOI:2,2209;
EXECUTION STARTED
COMMAND EXECUTED
< WOI:2,2210;
EXECUTION STARTED
RAN3086 Benefits
End-user benefits
This feature improves the overall end-user experience by accelerating a voice call setup time.
Operator benefits
This feature enables exchanging information between different Radio Access Technologies via Core
Network. With RIM, circuit-switched call fallback is faster.
With the UTRA SI RIM procedure, LTE eNB can inquire cell-specific System Information from RNC.
The RNC replies to the request with the relevant System Information Block (SIB) and the Master
Information Block (MIB) of a particular cell. RNC includes the MIB, SIB1, SIB3, SIB5, SIB7 in UTRA SI
RIM procedure.
LTE eNB uses the RNC's System Information for directing the UE to the WCDMA cell with RRC
CONNECTION RELEASE (UTRA BCCH container, Rel-9) message, so that the UE reads the SI of the
WCDMA cell from the release message. During a circuit-switched call fallback (CSFB), UE indicates
that it establishes the connection towards the RNC based on the SI from UTRA SI RIM procedure. The
indication is included in the RRC CONNECTION REQUEST (System Information Stored Indicator,
Rel-9).
Install the license key for the RAN3086: CSFB with RIM feature in the RNC and set the feature state
to
ON.
The feature code for this feature is 5418.
To set the feature state to ON, use the following command:
• for IPA-RNC:
ZW7M:FEA=5418:ON;
• for mcRNC:
set license feature-mgmt code 0000005418 feature-admin-state on
For information on managing licenses, see Licensing.
Before activating this feature the DefMeasCtrlReading WCEL parameter must be set to Enabled.
• LNADJW:rimStatus- provides and define the status of the RIM association to serving RNC.
• 3 states are defined for RIM capable WCDMA cells after RIM application of LTE1196:
- LNADJW:rimStatus==disabled:
- LNADJW:rimStatus==unavailable:
• The WCDMA neighbor cell is RIM enabled but no valid system information
from RIM procedure is available.
- LNADJW:rimStatus==available:
• The WCDMA neighbor cell is RIM enabled and valid system information from
RIM procedure is available.