Professional Documents
Culture Documents
Belt Id Chart Bkmrks 1339565382 PDF
Belt Id Chart Bkmrks 1339565382 PDF
Combine cross section designation with Outside Circumference (O.C.) to the nearest whole number, plus a zero to determine
Belt Part Number. Example: 5/8" top width 5VX belt with 80" O.C. equals 5VX800 V-Belt. X designates molded notch construction.
Eliminator®Belts
® 8mm widths include: 12mm, 22mm, 35mm and 60mm
Hi Power II V-Belts 1-1/4" 1-1/2"
Example: 640-8M-12E
14mm widths include: 20mm, 42mm, 65mm, 90mm and 120mm
7/8" Stock Belt Pitch Reference Dimensions
21/32"
1/2"
B
17/32" 29/32" C
5/16" 13/32" 3/4" 8mm 8mm 5.9mm 3.44mm
.315 in. .233 in. .135 in. A
A B C D E 14mm 14mm 10.2mm 6mm 8mm 14mm
Combine cross section plus Inside Circumference (I.C.) to determine belt part number. To calculate I.C., .552 in. .401 in. .236 in. Pitch Pitch
subtract the following values from the (O.C.):
Note: Eliminator belts replace RPP® belts in RPP sprockets.
Cross Section A B C D E RPP® is a registered trademark of Carlisle Power Transmission Products, Inc.
Subtract From O.C. 2" 3" (Above 210", 1.0") 4" (Above 210", 2.0") 5" (Above 210", 3.0") 7"(Above 210", 4.0")
Dubl-V belts are available in AA, BB, CC and DD cross sections
® ® 5mm
Truflex & PoweRated Light Duty V-Belts 3mm 3mm
.1181 in.
2.41mm
.095 in.
1.22mm
.048 in. Pitch
5mm 5mm 3.81mm 2.08mm
Truflex® 21/32" .197 in. .150 in. .082 in.
Part numbers are derived from industry 1/4" 3/8" 1/2"
20mm 20mm 13.2mm 8.4mm 20mm B
C
standard number. First digit in Gates 1/8" 7/32" 5/16" 3/8" .787 in. .520 in. .330 in. Pitch
number corresponds to first two digits of PowerGrip HTD belts in 3 and 5mm pitch are available in
A
industry standard number.
Example: 2450 = 4L450 Belt length is to 2L (0) 3L (1) 4L (2) 5L (3) TruMotion construction on a made-to-order basis.
Predator®PowerBand®Belts For MXL pitch TruMotion part #s, please reference catalog #19993.
*TruMotion®construction available in MXL,XL, and L pitches only.
Molded Notch Twin Power PowerGrip Timing Belts Twin Power PowerGrip GT 2 Belts
PowerBand®Belts
Stock Belt Pitch Reference Dimension Stock Belt
Stock BeltPitch
PitchReference
ReferenceDimension
Dimensions
A Timing A
Available in 3V, 3VX, 5V, 5VX & 8V sections. XL 5.08mm 3mm 3mm
.200 in. A .118 in.
L 9.53mm 5mm 5mm
® ®
Hi-Power II PowerBand Belts .375 in. .197 in.
Available in A, B, C & D sections. H 12.70mm
.500 in. GT®2 8mm 8mm
.315 in.
A
14mm 14mm
Note: Additional sizes available .552 in.
Micro-V®Belts J Section 3/32"
5/32"
3, 5, 8 & 14mm PowerGrip GT2 available in
the standard single sided belt widths
Identified by a three-part symbol consisting of:
(1) A standard length designation K* Section 13/64"
Heavy-Duty
Connector Belts also Available.