Professional Documents
Culture Documents
Improve
Productivity
Reduce Waste
3M™ Accuspray™ System is the equivalent of having
a brand new HVLP spray gun for a fraction of the
cost with each disposable nozzle replacement.
System
– Minimizes overspray – Reduces gun cleaning time
– Uses less solvent for clean up
Boosts Productivity
Works
– Helps decrease disposal cost
– Lowers spraying time
– Improves productivity and profitability
– Decreases sanding time
– Eliminates costly gun maintenance
1 2 3
Hand tighten or use two wrenches Attach an atomizing head to the Attach 3M™ PPS™ cup filled with
to connect the air flow gun - pull trigger back and hold, coating and attach compressed
control value. making sure the release buttons air hose.
are aligned with latch openings
- listen for a double click to
ensure that it is fully engaged.
7 8 9
Flush out atomizing head with Remove atomizing head - be Wipe off any additional residue
appropriate solvent until the sure to pull trigger back and pull from the fluid needle.
atomizing head is clear of coating. the atomizing head straight out
from the gun body to avoid
bending the fluid needle.
Technical Data
Weight 11.4 oz
Nozzle Size 1.4 mm, 1.8 mm, 2.0 mm
Operating Pressure (Full Trigger) 20 psi max
Air Consumption 10 cfm
4 5 6
Set air pressure at 20 psi at full Adjust fan and fluid flow to achieve When you are finished using the
trigger (air and fluid flowing). the desired size and wetness of the system remove the air line and
pattern. NOTE: when closing the fan 3M™ PPS™ Cup.
adjustment completely it may be
necessary to re-adjust the air
flow control valve.
10 11
1 2 3 4
Remove existing cup from spray gun. Thread correct adapter to spray gun. Remove liner from wall dispenser and If not using a scale to measure,
place into 3M™ PPS™ mixing cup. insert 3M™ PPS™ mix ratio film into
Weigh the paint according to paint cup before inserting liner in order to
manufacturer’s guidelines. measure the paint according to paint
manufacturer’s guidelines.
5 6 7 8
Mix product as needed. Take a lid (with built-in filter) from wall Position locking collar onto the 3M™ 3M™ PPS™ shaker core is used to
dispenser and snap into the 3M™ PPS™ cup/liner and turn until tight. distribute clamping force when shaker
PPS™ cup/liner. Insert sealing plug prior to shaking. machines are used to mix material.
9a 9b 10 11
Spray gun with correct adapter is Make sure that the lid fingers are fully The spray gun is now ready to Due to the fact that 3M™ PPS™ is a
attached with a quick quarter turn. engaged above adapter edge. spray as normal. NOTE: For spraying closed system, painters may now spray
upside-down, follow directions in the their gun completely perpendicular to
“Tips” section on purging air. their intended surface without fear of
material dripping on their job.
12 13 14 15
To return material back into gun cup Remaining material can be capped When you’re done using the system, Remove unused material from
before disconnecting spray gun, and stored for later use. the lid and liner can easily be removed the liner and place into proper
disconnect air line, invert gun (gravity Storage of paint should follow all from the cup. disposal container.
feed only) and pull trigger fully for a local regulations.
3M PPS
few seconds.
™ ™
16 17
Paint Preparation
System
Consult paint or solvent Material Safety A squeeze bottle (PN 37720) containing
Data Sheet (MSDS) in addition to local solvent or water enables fast gun
regulations or authorities for safe use cleaning once the 3M™ PPS™ cup is
and proper disposal. removed. More efficient painters make
facility more productive.
It’s Easy as Click and Spray
This revolutionary product allows you to have a brand new spray
gun on demand. The innovative technology was designed from
the inside out for the efficient and economical application
Reduces Improves Transfer of material. These atomizing heads deliver a large usable
Overspray Efficiency
pattern, with very low overspray and exceptional atomization.
Lowers Flatter
Coating Consumption Smoother Finish
PN 16587
PN16577
Dampening Coatings
Woodworking
Latex Paints, Adhesives
Med-Heavy
2.0 mm General Industrial
Epoxies, Undercoatings, Hi-build Primers
1.8 mm Transportation (Air and Wheeled)
1.4 mm Undercoatings, Adhesives, Specialty Coatings
Interchangeable Nozzle Size 3M™ Accuspray™ Spray Gun Model HGP (Pressure), PN 16587
Medium
2.0 mm
Transportation (Air and Wheel)
Adhesives, Primers, Base Coats
1.8 mm
Sign Shops
1.4 mm Primer, Base Coats
Interchangeable Nozzle Size 3M™ Accuspray™ Spray Gun Model HG18, PN 16570
Woodworking
Dye Stains, Clears, Lacquers
General Industrial
Medical Equipment Base/Clear, Mold Releases
Lower