Professional Documents
Culture Documents
Module 5
Start at
1. An FMS system, besides controlling navigation, thrust and auto-nav, also provides
a) take-off and landing warnings
b) dedicated status and warnings
c) GPWS warnings
The correct answer is b The FMS is not used for Take Off or Landing The GPWS warnings come from the
GPWS Computer
The correct answer is b Pallett - Aircraft Instruments Page 302 Fig. 12.5
The correct answer is c Warning flags 'in view' indicate failure. Normally the only coloured flag used is
RED, indicating failure
The correct answer is b Read up on logic gates - you need to know much more than you needed for Module
4
The correct answer is c Pallett - Aircraft Instruments Page 179 Fig. 7.12
Question :1
The correct answer is b The FMS is not used for Take Off or Landing The GPWS warnings come from the
GPWS Computer
Question :2
The correct answer is b Pallett - Aircraft Instruments Page 302 Fig. 12.5
Question :3
The correct answer is c Warning flags 'in view' indicate failure. Normally the only coloured flag used is
RED, indicating failure
Question :4
The correct answer is b Read up on logic gates - you need to know much more than you needed for Module
4
Question :5
The correct answer is b Pallett - Aircraft Instruments Page 159
Question :6
The correct answer is c See www.commspecial.com/fiberguide
Question :7
The correct answer is a Pallett - Aircraft Instruments Page 212
Question :8
The correct answer is b See www.l-ar.com/html/history.html
Question :9
The correct answer is c The OCTAL code has 8 digits, 0 - 7. To convert binary to octal divide the binary
number into groups of three starting from the right. You've got to know your binary, octal, hex and bcd
conversions!
Question :10
The correct answer is c Pallett - Aircraft Instruments Page 179 Fig. 7.12
Module 5
Stopwatch
Start at
The correct answer is a AWN 45 has been deleted at issue 133, but the examiners may not know that!
(Sinicism, surely not!)
4. Two connected fibre optic cable ends are parallel but not quite touching. This is called
a) lens connector
b) end to end coupling
c) end fire coupling
The correct answer is a Pallett - Aircraft Instruments Pages 302 & 304
9. An EADI display showing a moving runway moves down during the final stages of an
approach. The aircraft must
a) fly up
b) fly down
c) hold descent path
The correct answer is b At 200ft, during Approach, the Rising Runway starts to move up the EHSI display
until, at touch down, it touches the bottom of the aircraft symbol. If the Rising Runway start to move down
again it means that the aircraft is climbing and should FLY DOWN
Question :1
The correct answer is b Pallett - Aircraft Instruments Page 160
Question :2
The correct answer is a AWN 45 has been deleted at issue 133, but the examiners may not know that!
(Sinicism, surely not!)
Question :3
The correct answer is c Read up on software control - get a copy of AWNs
Question :4
The correct answer is b There are several websites on fibre optics
Question :5
The correct answer is c www.commspecial.com/fiberguide.htm
Question :6
The correct answer is b Pallett - Aircraft Instruments Page 284
Question :7
The correct answer is a www.floti.bell.ac.uk/MathsPhysics/light.htm
Question :8
The correct answer is a Pallett - Aircraft Instruments Pages 302 & 304
Question :9
The correct answer is b At 200ft, during Approach, the Rising Runway starts to move up the EHSI display
until, at touch down, it touches the bottom of the aircraft symbol. If the Rising Runway start to move down
again it means that the aircraft is climbing and should FLY DOWN
Question :10
The correct answer is a The FDR can have different inputs depending upon the age of the system, modern
systems use ARINC 573. The inputs to FDR DAU are only analogue, discreet and ARINC 429. The
interface between SGUs, EADI and EHSI is only ARINC 429
Module 5
Digital Techniques / Electronic Instrument Systems
Stopwatch
Start at
The correct answer is c Read up on logic gates - you need to know much more than you needed for Module
4!
The correct answer is b Northrop Institute of Technology - Electricity & Electronics for Aerospace
Vehicles Page 284
The correct answer is c Learn binary, octal, hex and BCD conversions
The correct answer is b Learn binary, octal, hex and BCD conversions
A B C
0 0 0
1 0 0
0 1 0
1 1 1
a) NAND gate
b) AND gate
c) OR gate
The correct answer is b Read up on logic gates - you need to know much more than you needed for
Module 4!
The correct answer is b Pallett - Aircraft Instruments Page 179 Fig. 7.12
Question :1
The correct answer is a Read up on Flight Data recording
Question :2
The correct answer is c Read up on logic gates - you need to know much more than you needed for Module
4!
Question :3
The correct answer is a Pallett - Aircraft Instruments Page 157
Question :4
The correct answer is b Northrop Institute of Technology - Electricity & Electronics for Aerospace
Vehicles Page 284
Question :5
The correct answer is c Pallett - Aircraft Instruments Page 156
Question :6
The correct answer is c Learn binary, octal, hex and BCD conversions
Question :7
The correct answer is b Learn binary, octal, hex and BCD conversions
Question :8
The correct answer is b Read up on logic gates - you need to know much more than you needed for Module
4!
Question :9
The correct answer is b Pallett - Aircraft Instruments Page 179 Fig. 7.12
Question :10
The correct answer is b Pallett - Aircraft Instruments Page 377
Module 5
Stopwatch
Start at
1. During an instrument approach, the glideslope pointer deflects below the glideslope
centre mark. This means the aircraft is positioned
a) above the glideslope
b) below the glideslope
c) to the left of the localiser
The correct answer is a Consider the centre of the G/S scale as the aircraft position and the pointer as the
centre of the G/S beam
The correct answer is a Engine parameters can be displayed on ECAM by selecting the Engine Page. See
Pallett - Aircraft Instrumnets and Integrated Systems Page 391
6. Where are the Digital Flight Data Recorder outputs supplied to?
a) The recording unit
b) Flight instruments
c) There are no outputs
The correct answer is c Information recorded in the DFDR is only accessable in the shop
The correct answer is a FMS warnings are displayed on EICAS and EFIS, but the answers given are
'EICAS' or 'EFIS only' so for the purposes of this question the correct answer is EICAS
The correct answer is a Ambiguous question. Do they mean who is responsible for following the program,
if so the answer is 'Pilot' or producing the program, then the answer is 'Manufacturer'
Question :2
The correct answer is a Engine parameters can be displayed on ECAM by selecting the Engine Page. See
Pallett - Aircraft Instrumnets and Integrated Systems Page 391
Question :3
The correct answer is a Read up on BITE systems
Question :4
The correct answer is b Boeing Maintenance Training notes for B757
Question :5
The correct answer is c Boeing Maintenance Training notes for B757
Question :6
The correct answer is c Information recorded in the DFDR is only accessable in the shop
Question :7
The correct answer is a FMS warnings are displayed on EICAS and EFIS, but the answers given are
'EICAS' or 'EFIS only' so for the purposes of this question the correct answer is EICAS
Question :8
The correct answer is a Ambiguous question. Do they mean who is responsible for following the program,
if so the answer is 'Pilot' or producing the program, then the answer is 'Manufacturer'
Question :9
The correct answer is a Read up on the flight director indication system
Question :10
The correct answer is c This is the definition of an analogue signal
Module 5
Stopwatch
Start at
The correct answer is c The little aeroplane pianted in the middle of the instrument
The correct answer is a Redundant FBW systems will continue to fly the aircraft
The correct answer is c Automatic Flight Control, Pallett and Coyle Page 296
Question :1
The correct answer is a The Y plates lie horizontal. Use the right hand rule to work out the direction of
electron beam movement. Aircraft Instruments & Integrated Systems, Pallett, page 287
Question :2
The correct answer is c The little aeroplane pianted in the middle of the instrument
Question :3
The correct answer is a Rotor Gear Box
Question :4
The correct answer is a Read up on INS
Question :5
The correct answer is c Read up on IRS
Question :6
The correct answer is c Read up on FMS navigation data management
Question :7
The correct answer is a Redundant FBW systems will continue to fly the aircraft
Question :8
The correct answer is b Read up on Load Alleviation system Ailerons move symmetrically upwards and No
4 and 5 spoilers move symmetrically upwards in a gust.
Question :9
The correct answer is c Automatic Flight Control, Pallett and Coyle Page 296
Question :10
The correct answer is c Read up on FBW systems
Module 5
Stopwatch
Start at
6. An FMS system, besides controlling navigation, thrust and auto-nav, also provides
a) take-off and landing warnings
b) dedicated status warnings
c) GPWS warnings
The correct answer is b Read up on FMS
7. In order to maintain HIRF protection, bonding checks between airframe and electrical
components carrying voltages greater than 50 volts RMS or DC or main earth return should not exceed
a) 1 megohm
b) 1 ohm
c) 0.05 ohm
8. Ribbon cables effected by mutual impedance and current loop leakage should be
protected by
a) shielding each individual conductor
b) connecting all conductors to a common earth
c) earthing each alternative conductor to separate point
The correct answer is b Read up on CRTs and see what a raster scan is
10. Normal transmission order of ARINC 629 LRUs in periodic mode is in order of
a) power up
b) shortest to largest TG
c) shortest to largest TI
The correct answer is b Aircraft Electricity and Electronics Eismin Page 149
Question :1
The correct answer is c Read up on ARINC 629 and 429
Question :2
The correct answer is b Read up on ILS system indication
Question :3
The correct answer is a Read up on ILS system indication
Question :4
The correct answer is b Read up on CRTs
Question :5
The correct answer is c Read up on ARINC 629 and 429
Question :6
The correct answer is b Read up on FMS
Question :7
The correct answer is b CAAIPs Leaflet 9-1
Question :8
The correct answer is c Read up on cable protection methods
Question :9
The correct answer is b Read up on CRTs and see what a raster scan is
Question :10
The correct answer is b Aircraft Electricity and Electronics Eismin Page 149
Module 5
Stopwatch
Start at
2. If an EFIS has 3 symbol generators, what is the purpose of the 3rd symbol generator?
a) Comparison with No.1 symbol generator
b) Standby
c) Parity function
The correct answer is a Do not get confused with an electrostatic CRT. Electromagnetic CRT uses
trapezoidal waveform to overcome the impedence of the coil
The correct answer is c You've got to know your binary, octal, hex and bcd conversions!
The correct answer is a AWN 45 has been deleted at issue 133, but the examiners may not know that!
(Sinicism, surely not!)
The correct answer is c Although a fiber optic cable is 'immune' from collecting HIRF, it can still transmit
HIRF which has been picked up by the source circuitry. An optoelectronic isolator will filter out the HIRF
prior to transmission.
Question :1
The correct answer is a Read up on CRTs
Question :2
The correct answer is b Read up on EFIS
Question :3
The correct answer is a Do not get confused with an electrostatic CRT. Electromagnetic CRT uses
trapezoidal waveform to overcome the impedence of the coil
Question :4
The correct answer is b Read up on FMS
Question :5
The correct answer is a Read up on fibre optics
Question :6
The correct answer is c You've got to know your binary, octal, hex and bcd conversions!
Question :7
The correct answer is a Read up on logic gates - you need to know much more than you needed for Module
4!
Question :8
The correct answer is a AWN 45 has been deleted at issue 133, but the examiners may not know that!
(Sinicism, surely not!)
Question :9
The correct answer is c Although a fiber optic cable is 'immune' from collecting HIRF, it can still transmit
HIRF which has been picked up by the source circuitry. An optoelectronic isolator will filter out the HIRF
prior to transmission.
Question :10
The correct answer is b Both a and b are correct. Aircraft Instruments and Integrated Systems Pallett Page
158 says 'source of the message', whereas ARINCs own tutorial (See FORUM Mod.5) says 'bits 8-1
contain parameter' (which Pallett's book also infers on Page 159).
Module 5
Stopwatch
Start at
The correct answer is b See Pallett's Micro Electronics In Aircraft Systsems or CAAIPs 9-4 para.7.1.3.
The correct answer is b Read up on CRTs - do not get confused with electrostatic deflection types - which
are more common on aircraft
Question :1
The correct answer is b The ARINC 629 TI is common to all LRUs.
Question :2
The correct answer is c See http://www.tpub.com/neets/tm/109-13.htm
Question :3
The correct answer is c Read up on fibre optics
Question :4
The correct answer is b See Pallett's Micro Electronics In Aircraft Systsems or CAAIPs 9-4 para.7.1.3.
Question :5
The correct answer is b Read up on CRTs - do not get confused with electrostatic deflection types - which
are more common on aircraft
Question :6
The correct answer is b See ANO Art 53 para.1
Question :7
The correct answer is c Read up on MIL-ST-1533 - a military version of ARINC 429
Question :8
The correct answer is c Read up on logic gates
Question :9
The correct answer is b Read up on parallel to series converion
Question :10
The correct answer is c Normally we consider the FMS as having 2 databases (1 navigational and 1
performance). (Jeppesen Avionics Fundamentals Page 385). However, the Navigational database is split in
two. 1 is for Jeppesen data, uploaded on the ground, the other is for pilot input data (additional waypoints
etc.). See http://www.b737.org.uk/fmc.htm for more
Module 5
Stopwatch
Start at
5. What shape does the waveform take to counter the impedance effect of the coils in an
electromagnetic controlled CRT?
a) Trapezoid
b) Sawtooth
c) Rectangular
The correct answer is a Read up on CRTs - do not get confused with an electrostatic CRT
The correct answer is a This means it can warn of inoperative equipment, but not when equipment is
providing incorrect data
8. The control of the speed or rate that the flight director command bars move can be
controlled by
a) position feedback
b) rate or velocity feedback
c) amplifier gain
The correct answer is b Read up on ILS indication
9. The Centralised Aircraft Monitoring System uses the maintenance mode of operation
a) in the air only
b) on the ground only
c) either in the air or on the ground
The correct answer is b Aircraft Electricity and Electronics, Eismin, 5th Edition Page 359
Question :1
The correct answer is c Read up on INS/IRS
Question :2
The correct answer is c Read up on INS/IRS
Question :3
The correct answer is b Read up on INS/IRS
Question :4
The correct answer is a Read up on computer controlled flight
Question :5
The correct answer is a Read up on CRTs - do not get confused with an electrostatic CRT
Question :6
The correct answer is a This means it can warn of inoperative equipment, but not when equipment is
providing incorrect data
Question :7
The correct answer is b Read up on ECAM
Question :8
The correct answer is b Read up on ILS indication
Question :9
The correct answer is b Aircraft Electricity and Electronics, Eismin, 5th Edition Page 359
Question :10
The correct answer is c Read up on EFIS
Module 5
Stopwatch
Start at
2. EFIS displays of the right hand and left hand displays are compared by comparators in
the
a) FMS
b) EICAS
c) Symbol Generators
The correct answer is c Aircraft Instruments and Integrated Systems. Pallett Page 102
Question :1
The correct answer is b Read up on EFIS
Question :2
The correct answer is c Read up on EFIS
Question :3
The correct answer is c Aircraft Instruments and Integrated Systems. Pallett Page 102
Question :4
The correct answer is b Jeppesen Avionics Fundamentals Page 137
Question :5
The correct answer is a Jeppesen Avionics Fundamentals Page 137
Question :6
The correct answer is a Both Static and Total Air Temperatures are outputs of a digital ADC
Question :7
The correct answer is a Read up ARINC 429 and 629
Question :8
The correct answer is b Read up on fibre optics
Question :9
The correct answer is a Read up on fibre optics
Question :10
The correct answer is a Understanding HIRF By Gerald L. Fuller
Module 5
Stopwatch
Start at
The correct answer is b Read up on ARINC 429 and 629 data bus systems
10. When 4 binary serial counters are connected in cascade for frequency division, what
division factor is required
a) 4
b) 8
c) 16
The correct answer is c Each serial counter changes its state once every 2 clock pulses. So 4 serial counters
devides by 2x2x2x2 = 16
Question :1
The correct answer is b Read up on ARINC 429 and 629 data bus systems
Question :2
The correct answer is c Read up on logic gates
Question :3
The correct answer is a Read up on hexadecimal numbering system
Question :4
The correct answer is b Read up on binary to decimal converion
Question :5
The correct answer is a Read up on MIL-STD-1533 data bus systems
Question :6
The correct answer is b Digital is 1s and 0s
Question :7
The correct answer is b Read up on binary to decimal converion
Question :8
The correct answer is c Read up on logic gates
Question :9
The correct answer is a Read up on fibre optics
Question :10
The correct answer is c Each serial counter changes its state once every 2 clock pulses. So 4 serial counters
devides by 2x2x2x2 = 16
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 12. You've been here 1 times.
1. Magnetic deflection in a CRT is achieved by
a) a sawtooth waveform
b) a trapezoidal waveform
c) a sinusoidal voltage
The correct answer is b Do not get confused with electrostatic deflection (plates), which would be sawtooth
2. Fly By Wire systems in the fully active mode, the actuators will
a) both be active
b) one in active mode, one in damping mode
c) both be in damping mode, awaiting control inputs
The correct answer is b Read up on the purpose and use of parity bit
The correct answer is b ELAC = Elevator Aileron Computer, SEC = Spoilers Elevator Computer and FAC
= Flight Augmentation Computers (rudder)
Question :1
The correct answer is b Do not get confused with electrostatic deflection (plates), which would be sawtooth
Question :2
The correct answer is b Read up on Fly by Wire
Question :3
The correct answer is b Read up on the purpose and use of parity bit
Question :4
The correct answer is b ELAC = Elevator Aileron Computer, SEC = Spoilers Elevator Computer and FAC
= Flight Augmentation Computers (rudder)
Question :5
The correct answer is c Read up on fibre optics
Question :6
The correct answer is b SDI = Source Destination Ident
Question :7
The correct answer is b Read up on decimal conversions
Question :8
The correct answer is b Read up on multiplexing
Question :9
The correct answer is a Read up on purpose and use of parity bit
Question :10
The correct answer is a Each serial counter changes its state once every 2 clock pulses. So 3 serial counters
devides by 2x2x2 = 8
Module 5
Stopwatch
Start at
5. What is the advantage of a single mode fibre optic over ordinary wire?
a) Large bandwidth
b) Small bend radius
c) Not prone to damage
Question :1
The correct answer is a See AWN 45.
Question :2
The correct answer is b Read up on fibre optics.
Question :3
The correct answer is b Read up on ARINC 429 word format.
Question :4
The correct answer is c Read up on optoelectronic devices (from Module 4).
Question :5
The correct answer is a Read up on fibre optics.
Question :6
The correct answer is b Read up on ARINC 429 and 629.
Question :7
The correct answer is a Read up on hexidecimal numbering system.
Question :8
The correct answer is b Read up on decimal to binary conversion.
Question :9
The correct answer is b read up on octal to hex conversion.
Question :10
The correct answer is b Read up on logic gates.
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is a Read up on ARINC 429 and 629 data bus systems
The correct answer is c Boeing manual says 100% cotton twine. Other manuals say ESDS label. However,
it could be considered that ESDS labels do not 'seal'.
9. Convert 1D to binary
a) 29
b) 11101
c) 101001
Question :1
The correct answer is a Read up on ARINC 429 and 629 data bus systems
Question :2
The correct answer is c Read up on hexadecimal numbering system
Question :3
The correct answer is b Read up on logic gates
Question :4
The correct answer is a Read up on logic gates
Question :5
The correct answer is a Read up on software classification
Question :6
The correct answer is c Boeing manual says 100% cotton twine. Other manuals say ESDS label. However,
it could be considered that ESDS labels do not 'seal'.
Question :7
The correct answer is a Read up on decimal to binary conversion
Question :8
The correct answer is a CAAIPs Leaflet 9-4 5.3.1 - closest answer
Question :9
The correct answer is b Read up on hex to binary conversion
Question :10
The correct answer is b The TI is common to all LRUs on ARINC 629
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is b Read up on ARINC 429 and 629 data bus systems
The correct answer is b See ANO Art 53 para.1. Although JAR Ops states that the CVR must begin when
the aircraft is capable of moving under its own power.
The correct answer is c Read up on ARINC 429 and 629 data bus systems (429 uses either BCD or binary)
Question :1
The correct answer is a Read up on hex to octal conversions
Question :2
The correct answer is b Read up on fibre optics
Question :3
The correct answer is a Read up on anti-static precautions
Question :4
The correct answer is b Read up on ARINC 429 and 629 data bus systems
Question :5
The correct answer is b See ANO Art 53 para.1. Although JAR Ops states that the CVR must begin when
the aircraft is capable of moving under its own power.
Question :6
The correct answer is b Read up on ACARS
Question :7
The correct answer is c Read up on ARINC 429 and 629 data bus systems (429 uses either BCD or binary)
Question :8
The correct answer is c Read up on autopilot
Question :9
The correct answer is b Read up on B-RNAV
Question :10
The correct answer is b Read up on basic radar theory
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is b Two versions of ARINC 429. BCD uses 11 - 29, Binary uses 11 - 28.
2. Engine parameters are displayed on
a) ECAM
b) EHSI
c) CDU
3. A flight deck CRT LRU is being replaced. What does the ESDS label indicate?
a) Wrist straps should be worn
b) Do not touch plug pins or leave them exposed
c) Remove power before connecting
The correct answer is b See Pallett's Micro Electronics In Aircraft Systsems or CAAIPs 9-4 para.7.1.3.
The correct answer is b Read up on ARINC 429 and 629 data bus systems
8. When using a wrist strap, before touching the LRU the resistance should be measured
from your skin to the end of the earth probe. This should be
a) more than 10 kilohms
b) less than 10 kilohms
c) less than 1 ohm
Question :1
The correct answer is b Two versions of ARINC 429. BCD uses 11 - 29, Binary uses 11 - 28.
Question :2
The correct answer is a Read up on ECAM/EICAS systems
Question :3
The correct answer is b See Pallett's Micro Electronics In Aircraft Systsems or CAAIPs 9-4 para.7.1.3.
Question :4
The correct answer is c Read up on Air DAta Computers
Question :5
The correct answer is c Read up on hexadecimal numering system
Question :6
The correct answer is b Read up on ARINC 429 and 629 data bus systems
Question :7
The correct answer is b Read up on thyristos
Question :8
The correct answer is a Read up on anti-static precautions
Question :9
The correct answer is b Read up on binary to decimal converions
Question :10
The correct answer is a Read up on analogue/digital definitions
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 17. You've been here 1 times.
1. Within a 3 bit frequency cascade, division is to
a) 8
b) 4
c) 2
The correct answer is a The exact definition of HIRF does not include electrostatc discharge (ESD). But
only interference from outside sources. Understanding HIRF By Gerald L. Fuller
The correct answer is a Read up on BCD to decimal conversions (BCD is not the same a s binary)
The correct answer is c Read up on ARINC 429 and 629 data bus systems
The correct answer is b Read up on ARINC 429 and 629 data bus systems
The correct answer is b Read up on ARINC 429 and 629 data bus systems
Question :1
The correct answer is a Read up on counters
Question :2
The correct answer is b Read up on radio altimeters and ILS
Question :3
The correct answer is a The exact definition of HIRF does not include electrostatc discharge (ESD). But
only interference from outside sources. Understanding HIRF By Gerald L. Fuller
Question :4
The correct answer is a Read up on BCD to decimal conversions (BCD is not the same a s binary)
Question :5
The correct answer is a Read up on decimal to binary conversions
Question :6
The correct answer is c Read up on binary to octal conversions
Question :7
The correct answer is a Understanding HIRF By Gerald L. Fuller
Question :8
The correct answer is c Read up on ARINC 429 and 629 data bus systems
Question :9
The correct answer is b Read up on ARINC 429 and 629 data bus systems
Question :10
The correct answer is b Read up on ARINC 429 and 629 data bus systems
Practice Exam
Module 5
Stopwatch
Start at
2. Very Large Scale Integrated (VLSI) means the number of gates in a single IC is
a) up to 1000
b) up to 10,000
c) over 10,000
4. A BYTE is usually
a) a 12 bit word
b) an 8 bit word
c) a six bit word
6. The fibre optic cable can be identified on aircraft by its jacket colour which is
a) purple
b) red
c) yellow
Question :1
The correct answer is b Read up on logic gate systems
Question :2
The correct answer is c Read up on logic gate systems
Question :3
The correct answer is c Read up on memory (RAM) types
Question :4
The correct answer is b Read up on computer terminology
Question :5
The correct answer is b Read up on MIL-STD-1553 data bus system
Question :6
The correct answer is a Read up on fibre optics
Question :7
The correct answer is c Read up on fibre optics
Question :8
The correct answer is a Read up on CRTs
Question :9
The correct answer is a Understanding HIRF By Gerald L. Fuller
Question :10
The correct answer is c Aircraft instruments and integrated systems,(pallet) page 302 fig 12.5 eadi flight
director command bars are magenta
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is a Read up on binary addition and binary to decimal conversions
The correct answer is a Read up on ARINC 429 data bus word format
Question :1
The correct answer is a Read up on Air Data Computer
Question :2
The correct answer is b Read up on binary to decimal conversion
Question :3
The correct answer is a Read up on Flight Data Recorder
Question :4
The correct answer is a Read up on logic gates
Question :5
The correct answer is c Read up on Digital AIr Data Computer (IRMP is the control for the Inertial
Referencing Unit)
Question :6
The correct answer is b Microelectronics in Aircraft Systems - Pallet. pg 219
Question :7
The correct answer is c Read up on anti-static precautions
Question :8
The correct answer is a Read up on satallite navigation (or GPS)
Question :9
The correct answer is a Read up on binary addition and binary to decimal conversions
Question :10
The correct answer is a Read up on ARINC 429 data bus word format
Practice Exam
Module 5
Stopwatch
Start at
a) Or gate
b) NOR gate
c) NOT gate
9. With a relative humidity of 10% to 20%, if you walked over a carpet what electrostatic
voltage value would you expect to see?
a) 6,000 volts
b) 12,000 volts
c) 35,000 volts
The correct answer is c Read up on static electricity
10. Before fitting a Printed Circuit Board you should check the
a) resistance between skin and strap end plug is less than 10 megohms
b) resistance between skin and strap end plug is more than 1 megohms
c) resistance between strap and strap end plug is less than 1 megohms
The correct answer is c CAAIP Leaflet 9-4 5.3.1
Question :1
The correct answer is c Read up on fibre optics
Question :2
The correct answer is b AWN 43
Question :3
The correct answer is b Read up on logic gates
Question :4
The correct answer is a Read up on Cathode Ray Tubes
Question :5
The correct answer is b Read up on fibre optics
Question :6
The correct answer is a Read up on HIRF protection
Question :7
The correct answer is a Read up on binary to decimal converion
Question :8
The correct answer is a Read up on octal to decimal conversion
Question :9
The correct answer is c Read up on static electricity
Question :10
The correct answer is c CAAIP Leaflet 9-4 5.3.1
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 21. You've been here 1 times.
1. A fibre optic data bus
a) can only transmit 1 message at a time
b) can transmit several messages simultaneously
c) is only used for non essential messages
The correct answer is b JAR OPS Para 1.700 (c) OR answer c by CAP 393 Section I Para 53
3. On an ARINC 629 data bus, the maximum amount of current-mode couplers per data bus
is
a) 46
b) 120
c) 64
The correct answer is b 120 LRUs maximum (but the B777 uses 46)
The correct answer is a Read up on ARINC 429 and 629 data bus systems
The correct answer is a Read up on ARINC 429 and 629 data bus systems
The correct answer is a Read up on ARINC 429 and 629 data bus systems
9. A given transducer provides a voltage which corresponds to true heading. This voltage
can be converted to 'bits' by using a
a) commutator
b) digital to analogue converter
c) analogue to digital converter
Question :1
The correct answer is b Read up on fibre optics
Question :2
The correct answer is b JAR OPS Para 1.700 (c) OR answer c by CAP 393 Section I Para 53
Question :3
The correct answer is b 120 LRUs maximum (but the B777 uses 46)
Question :4
The correct answer is a Read up on ARINC 429 and 629 data bus systems
Question :5
The correct answer is a Read up on ARINC 429 and 629 data bus systems
Question :6
The correct answer is a Read up on ARINC 429 and 629 data bus systems
Question :7
The correct answer is b Read up on DACs and ADCs
Question :8
The correct answer is a Read up on DACs and ADCs
Question :9
The correct answer is c Read up on DACs and ADCs
Question :10
The correct answer is b Read up on logic gates
Your total score is : 0
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is c Read up on ARINC 429 and 629 data bus systems
The correct answer is a Read up on ARINC 429 and 629 data bus systems
3. Care must be taken when installing ARINC 629 cables into bus panels, damage to cables
can cause
a) arcing of high voltage signals
b) standing waves.
c) corrosion of the conductor
The correct answer is c Read up on ARINC 429 and 629 data bus systems
The correct answer is c Read up on ARINC 429 and 629 data bus systems
Question :1
The correct answer is c Read up on ARINC 429 and 629 data bus systems
Question :2
The correct answer is a Read up on ARINC 429 and 629 data bus systems
Question :3
The correct answer is c Read up on ARINC 429 and 629 data bus systems
Question :4
The correct answer is c Read up on ARINC 429 and 629 data bus systems
Question :5
The correct answer is c Read up on acceleration - velocity - distance computations
Question :6
The correct answer is a Read up on Inertial Reference Systems
Question :7
The correct answer is a Read up on multiplexing
Question :8
The correct answer is b Read up on ADCs and DACs
Question :9
The correct answer is b Read up on ADCs and DACs
Question :10
The correct answer is c Read up on fibre optics
Practice Exam
Module 5
Stopwatch
Start at
3. The FMS carries out a Rho/Theta navigation function, the purpose of this is to
a) update the IRS system with an accurate position fix of latitude and longitude
b) to update the EMS with the new lateral flight profile for the flight plan
c) to update the VOR and DME systems with an accurate position fix
6. In a fly by wire system, if the pilot control input is derived from a side stick controller:
a) control surface feedback is fed to the side stick
b) there is no control surface feedback to the side stick
c) there will be only control surface feedback to the side stick after a computer
failure
8. The resistance of the wrist strap used as part of anti static precautions should be
a) 0 - 200 ohm
b) 250 kilohm - 1.5 megohm
c) 20 megohm - 200 megohm
Question :1
The correct answer is b Read up on IRS
Question :2
The correct answer is a Read up on IRS
Question :3
The correct answer is a Read up on FMS - IRS update function
Question :4
The correct answer is c Read up on FMS database updating
Question :5
The correct answer is b Read up on fly-by-wire
Question :6
The correct answer is b Read up on fly-by-wire
Question :7
The correct answer is b Read up on RAM types
Question :8
The correct answer is b CAAIPs Leaflet 9-4 5.3.1
Question :9
The correct answer is a <See http://www.i-garden.org/docu/cecs/cs14.pdf
Question :10
The correct answer is b Read up on RAM types
Practice Exam
Module 5
Stopwatch
Start at
2. What must be entered into the IRS before the aircraft can be moved?
a) Present position
b) Flight plan
c) Cruise height
6. When the voltage that represents a logic 1 state is less than the voltage that represents a
logic 0 state, the logic being used is
a) either positive or negative
b) positive
c) negative
7. The output of an AND gate having two inputs A and B is logic 1. The two inputs will
have the logic states of
a) A = 0, B = 0
b) A = 1, B = 1
c) A = 1, B = 0
The correct answer is a Read up on the ARINC 429 and 629 data bus system
How did you do?
------------------------------------
Question :1
The correct answer is c Jeppesen Avionics Fundamentals Page 137
Question :2
The correct answer is a Read up on IRS
Question :3
The correct answer is b Read up on FMS databases
Question :4
The correct answer is a Read up on fly by wire
Question :5
The correct answer is b Read up on DACs and CADs
Question :6
The correct answer is c Read up on logic systems
Question :7
The correct answer is b Read up on logic gates
Question :8
The correct answer is b Read up on CPU architecture
Question :9
The correct answer is c Read up on binary to octal conversions
Question :10
The correct answer is a Read up on the ARINC 429 and 629 data bus system
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 25. You've been here 1 times.
1. Testing of HIRF on aircraft systems is done
a) by periodically listening for interference on all systems
b) at and during production and testing (initial certification)
c) only after a report of radio interference
The correct answer is a Aircraft Instruments and Integrated Systems. Pallett Page 247 & 248
7. If a fly by wire actuator loses hydraulic power the control surface will
a) automatically move back to the neutral position
b) remain rigid in the failure position
c) remain in the failure position but may move due to aerodynamic pressure
8. The output of an OR gate having two inputs A and B is logic 0. The two inputs will have
the logic states of
a) A = 0, B = 0
b) A = 1, B = 0
c) A = 0, B = 1
The correct answer is a Read up logic gates
Question :1
The correct answer is b Understanding HIRF By Gerald L. Fuller
Question :2
The correct answer is a Read up on HIRF protection
Question :3
The correct answer is a Read up on electrical testing
Question :4
The correct answer is b Read up on acceleration - velocity - distance computations
Question :5
The correct answer is a Aircraft Instruments and Integrated Systems. Pallett Page 247 & 248
Question :6
The correct answer is b Read up on FMS databases
Question :7
The correct answer is c Read up on fly by wire systems
Question :8
The correct answer is a Read up logic gates
Question :9
The correct answer is a Read up on cable installations
Question :10
The correct answer is c Read up on cable installations
Practice Exam
Module 5
Stopwatch
Start at
2. When carrying out airframe bonding checks as part of a program of HIRF prevention the
airframe bonding resistance should be less than
a) 50 milliohms
b) 100 milliohms
c) 1 ohm
4. IRS alignment
a) takes up to 10 minutes and the present position can be entered at any time during
alignment
b) takes up to 10 minutes and present position must be entered before alignment.
c) takes up to 10 minutes and the previous flight shut down present position is used
for the alignment
5. A fault light appears on the IRS Mode Selector Unit during the alignment sequence. The
correct action is
a) immediately switch off and select the standby system.
b) select HDG/STS on the Inertial System Display Unit (ISDU), observe the action
code in the right alpha/numeric display
c) refer to the warning display on the EICAS/ECAM system.
The correct answer is b Read up on FMS databases (navigation and performance databases)
10. A semiconductor which emits photons and releases electrons when stimulated by photons
is called
a) an LED
b) a photodiode
c) a laser diode
The correct answer is c Read up on laser diodes (Light Amplification by Stimulated Emission of Radiation)
How did you do?
------------------------------------
Question :1
The correct answer is c Read up on fibre optics
Question :2
The correct answer is a Read up on HIRF protection
Question :3
The correct answer is a See discussion in Forum Module 5 for details
Question :4
The correct answer is a Read up on IRS
Question :5
The correct answer is b Read up on IRS
Question :6
The correct answer is c Read up on EFIS
Question :7
The correct answer is b Read up on FMS databases (navigation and performance databases)
Question :8
The correct answer is c Read up on fly by wire
Question :9
The correct answer is b Read up on fibre optics
Question :10
The correct answer is c Read up on laser diodes (Light Amplification by Stimulated Emission of Radiation)
Practice Exam
Module 5
Stopwatch
Start at
2. A Liquid Crystal Display (LCD) has the advantage over a CRT because
a) it displays more colours
b) it requires less servicing
c) it requires no cooling
5. An encoder changes
a) analogue to digital
b) digital to analogue
c) data from one format to another
The correct answer is a Read up on ARINC 429 and 629 data bus systems
a) AND gate
b) OR gate
c) NOR gate
Question :1
The correct answer is a Jeppesen Avionics Fundamentals Page 137
Question :2
The correct answer is c Read up on LCDs and CRTs
Question :3
The correct answer is c Read up on EFIS
Question :4
The correct answer is c Read up on fly by wire systems
Question :5
The correct answer is c Read up on encoders and decoders
Question :6
The correct answer is a Read up on altitude encoders and grey code
Question :7
The correct answer is a Read up on ARINC 429 and 629 data bus systems
Question :8
The correct answer is b Read up on logic gates
Question :9
The correct answer is b Read up on logic gates
Question :10
The correct answer is c Read up on software management
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 28. You've been here 1 times.
1. Ribbon cables affected by mutual impedance and current loop leakage are protected by
a) earthing each conductor
b) earthing each alternate conductor
c) wrapping the complete ribbon in an earthed shield
7. When a JK flip flop is used as a memory device, what type of memory would it be?
a) non-volatile
b) read-only
c) volatile
8. Once an ARINC 629 LRU has transmitted a message it will wait how long before
transmitting again?
a) Until the end of the synchronization gap.
b) Until the end of the transmit interval
c) Until the start of the terminal gap
Question :1
The correct answer is b Read up on HIRF protection
Question :2
The correct answer is a Read up on computer terminology
Question :3
The correct answer is b Read up on flip-flops / vibrators
Question :4
The correct answer is b Read up on boolean algebra
Question :5
The correct answer is b Read up on adders
Question :6
The correct answer is b Reead up on LED operation
Question :7
The correct answer is c Read up on memory types
Question :8
The correct answer is b Read up on ARINC 629 data word format
Question :9
The correct answer is c Label is Octal - MSB to right - so yes, it is backwards
Question :10
The correct answer is c Read up on the ARINC data bus systems
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is c Aircraft Electricity and Electronics, Eismin, 5th Edition Page 146
8. If a magnetic field is parallel to the X plates in a CRT, which way will the beam move?
a) Diagonally
b) Vertically
c) Horizontally
The correct answer is c Read up on CRTs
Question :1
The correct answer is b Only these require real time reference
Question :2
The correct answer is a Read up on fibre optics
Question :3
The correct answer is c Aircraft Electricity and Electronics, Eismin, 5th Edition Page 146
Question :4
The correct answer is c Read up on logic gates
Question :5
The correct answer is a Read up on CPU components
Question :6
The correct answer is b Read up on multiplexing / demultiplexing
Question :7
The correct answer is a Read up on shift registers
Question :8
The correct answer is c Read up on CRTs
Question :9
The correct answer is a Read up on EFIS
Question :10
The correct answer is b Read up on binary to hex conversions
Module 5
Stopwatch
Start at
3. A digital to analogue converter that requires the output to range between 0v and -10v
would have
a) a non-inverting amplifier in parallel with the output line
b) an inverting amplifier in series with the output line
c) a non-inverting amplifier in line with the output with a resistor to ground
4. An LED display is
a) red and green
b) monochrome only
c) high definition
5. An EFIS ADI display will show along with pitch and roll
a) flight director bars, autoland, compass rose, altitude
b) flight director bars, autoland, altitude, range to altitude, decision height
c) decision height, autoland, rad alt , altitude
6. A full operation system BITE check will carry out a internal system test that ensures the
system meets design requirements and is operational
a) but will not move the controls
b) as well as checking full system and will move the controls to their stops
c) as well as checking full system but will not move the controls to their stops
The correct answer is c Digital Avionic Systems - Cary Spitzer. Page 109, Arinc report 604 guidance for
design and use of built in test equipment states... 'BITE should excercise the hardware sufficiently to
determine if it meets the performance requirements but should not drive it against mechanical stops.'
7. If on a flight deck EFIS system all the displays were missing one bit of information this is
most likely to be
a) the symbol generator and display
b) the input sensor bus and display controller
c) the display controller and symbol generator
8. A arinc data word is bits 11-29, if bits 11-18 are patched which of the following would be
the LSB bit
a) 19
b) 29
c) 21
9. What is a band?
a) A block of data
b) A bit of data
c) A byte of data
Question :1
The correct answer is a
Question :2
The correct answer is a
Question :3
The correct answer is b
Question :4
The correct answer is b
Question :5
The correct answer is c
Question :6
The correct answer is c Digital Avionic Systems - Cary Spitzer. Page 109, Arinc report 604 guidance for
design and use of built in test equipment states... 'BITE should excercise the hardware sufficiently to
determine if it meets the performance requirements but should not drive it against mechanical stops.'
Question :7
The correct answer is b
Question :8
The correct answer is a
Question :9
The correct answer is b
Question :10
The correct answer is c
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 143
Question :1
The correct answer is a See discussion in Forum Module 5 for details
Question :2
The correct answer is a
Question :3
The correct answer is b
Question :4
The correct answer is a
Question :5
The correct answer is a
Question :6
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 143
Question :7
The correct answer is b
Question :8
The correct answer is b Introduction to Fiber Optics John Crisp Page 50
Question :9
The correct answer is a Introduction to Fiber Optics John Crisp Page 29
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 270
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 148
The correct answer is a Aircraft Instruments and Integrated Systems EHJ Pallett Page 297
The correct answer is b The outer cladding is glass, so it is refractive (but less so than the core). Cladding
causes Total Internal Reflection (TIR), so question can be interpreted in two ways.
Question :1
The correct answer is a
Question :2
The correct answer is a
Question :3
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 270
Question :4
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 148
Question :5
The correct answer is a Aircraft Instruments and Integrated Systems EHJ Pallett Page 297
Question :6
The correct answer is a
Question :7
The correct answer is b
Question :8
The correct answer is b The outer cladding is glass, so it is refractive (but less so than the core). Cladding
causes Total Internal Reflection (TIR), so question can be interpreted in two ways.
Question :9
The correct answer is a
Question :10
The correct answer is c
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 146
The correct answer is b 757 MM 34-22-00 page 40 (p) and 737 MM 34-22-00 page 47, 4(b)
6. A typical example of a mass storage memory device which "write once" and "read many"
is
a) a CD Rom
b) an IC
c) a magnetic tape
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 144
9. Electromagnetic compatibility is achieved by
a) shielding, screening, earthing, bonding and interference filters
b) enclosing the system with same frequency and strength of which screening is
done
c) coating in a conductive paint
Question :1
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 146
Question :2
The correct answer is c
Question :3
The correct answer is a
Question :4
The correct answer is b 757 MM 34-22-00 page 40 (p) and 737 MM 34-22-00 page 47, 4(b)
Question :5
The correct answer is b
Question :6
The correct answer is a
Question :7
The correct answer is a Microelectronics in Aircraft Systems. Pallett. Page 219
Question :8
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 144
Question :9
The correct answer is a
Question :10
The correct answer is a See discussion in FORUM Module 5
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is a MM 737-300/400/500, 34-22-00 page 47 4b or MM 757 34-22-00 page 40 (p).
'The special symbols, characters, letters, vectors and arcs are displayed using the stroke method. The EADI
sky/ground ball or EHSI weather radar are displayed using the raster method
The correct answer is b CAP 393 Section I Para 53, OR answer c by JAR OPS Para 1.700 (c)
10. Within an EFIS display system, all displays have 1 bit of information missing. What
would be the most probable cause?
a) Symbol generator and sensor input
b) Display controller and sensor input bus
c) Display controller and symbol generator
Question :1
The correct answer is a MM 737-300/400/500, 34-22-00 page 47 4b or MM 757 34-22-00 page 40 (p). 'The
special symbols, characters, letters, vectors and arcs are displayed using the stroke method. The EADI
sky/ground ball or EHSI weather radar are displayed using the raster method
Question :2
The correct answer is b
Question :3
The correct answer is b
Question :4
The correct answer is c
Question :5
The correct answer is c
Question :6
The correct answer is b http://www.condoreng.com ARINC 429 tutorial
Question :7
The correct answer is b CAP 393 Section I Para 53, OR answer c by JAR OPS Para 1.700 (c)
Question :8
The correct answer is a
Question :9
The correct answer is b
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 146
4. 2D in decimal is
a) 45
b) 43
c) 41
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 132
5. The operational data base of the FMS may have to be modified in flight
a) by the pilot
b) automatically by the DADC
c) It cannot be modified in flight
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 121
The correct answer is b Aircraft Instruments and Integrated Systems EHJ Pallett Page 305
The correct answer is c Aircraft Instruments and Integrated Systems Pallett Page 162.
Question :1
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 146
Question :2
The correct answer is a
Question :3
The correct answer is c
Question :4
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 132
Question :5
The correct answer is c
Question :6
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 121
Question :7
The correct answer is b Aircraft Instruments and Integrated Systems EHJ Pallett Page 305
Question :8
The correct answer is c Aircraft Instruments and Integrated Systems Pallett Page 162.
Question :9
The correct answer is b
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 140
3. 84 decimal in hexadecimal is
a) 54
b) f4
c) 5f
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 132
4. EADI displays
a) pitch and roll attitudes
b) heading and weather radar
c) pitch, roll and waypoints
8. A method used in modern aircraft for reporting in flight faults to an engineering and
monitoring ground station is
a) TCAS II
b) ACARS
c) TAWS
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 299
Question :2
The correct answer is a
Question :3
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 132
Question :4
The correct answer is a
Question :5
The correct answer is b
Question :6
The correct answer is a
Question :7
The correct answer is a
Question :8
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 299
Question :9
The correct answer is c
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
7. When the power is removed from a bi-stable memory device, it's memory will
a) be lost indefinitely
b) be saved indefinitely
c) downloaded to memory
10. A multiplexer
a) takes many signals in and converts it to a serial transmission output
b) takes one signal in and converts it to a parallel transmission output
c) takes many signals in and puts these in a parallel transmission on the output
Question :1
The correct answer is b
Question :2
The correct answer is a
Question :3
The correct answer is b
Question :4
The correct answer is b
Question :5
The correct answer is b
Question :6
The correct answer is b Introduction to Fiber Optics J Crisp Page 18/19
Question :7
The correct answer is a
Question :8
The correct answer is a
Question :9
The correct answer is b AWN 45
Question :10
The correct answer is a
Practice Exam
Module 5
Start at
The correct answer is b Aircraft Instruments and Intergrated Systems EHJ Pallett Page 153 Basic CPU,.
Aircraft Electricity and Electronics Eismin 5th Edition Page 145
2. The ARINC 429 system uses the following system to transfer data
a) non return to zero
b) harvard bi phase
c) bi-directional return to zero
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 148.
http://www.condoreng.com ARINC 429 tutorial
6. To deflect the beam of a CRT horizontally, coils are placed on the neck of the tube
a) one on the side, one at the bottom
b) each side
c) top and bottom
7. During flight (non fault conditions) the EICAS system displays on the lower CRT
a) secondary engine parameters
b) synoptic display
c) flight phase page
The correct answer is a
The correct answer is a AWN45a para 3.1.3 (BCAR section A sub section A8)
10. Modern aircraft with electronic displays would display information on airframe and
engine on which system?
a) Flight management system
b) Electronic centralised aircraft monitoring system (ECAM)
c) EADI
The correct answer is b
Question :1
The correct answer is b Aircraft Instruments and Intergrated Systems EHJ Pallett Page 153 Basic CPU,.
Aircraft Electricity and Electronics Eismin 5th Edition Page 145
Question :2
The correct answer is c http://www.condoreng.com ARINC 429 tutorial
Question :3
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 148.
http://www.condoreng.com ARINC 429 tutorial
Question :4
The correct answer is b http://www.condoreng.com MIL-STD-1553 tutorial
Question :5
The correct answer is c
Question :6
The correct answer is c
Question :7
The correct answer is a
Question :8
The correct answer is a AWN45a para 3.1.3 (BCAR section A sub section A8)
Question :9
The correct answer is a
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
2. Data to flight data recorder can be taken form a communal data bus if
• a) it goes directly to it
• b) the power is within flight data recorder limits
• c) if source isolation has been considered
3. In arinc 429 data field is bits 11 to 28. If the bits 11 to 18 had pad bits, the L.S.B. Of the data would
be
• a) bit 19
• b) bit 11
• c) bit 28
5. After attaching a wrist strap to you wrist (which is connected to aircraft ground), prior to removal of
ESDS equipment, the resistance measured
• a) between the strap and the pin ground must be >10 Megohms
• b) between your skin and the pin ground must be <10 megohms
• c) between the strap and the pin ground must be <10 meghms
The correct answer is b Answer found in Boeing SWPM. 20-41-01 3(2) (e) Hold the red lead of the (test)
meter between the forefinger and the thumb. The acceptable range is less than 10,000,000 ohms
The correct answer is c The exact definition of HIRF does not include electrostatc discharge (ESD). But
only interference from outside sources. Understanding HIRF By Gerald L. Fuller
8. If the magnetic deflection plates produce a magnetic field which is parallel to the horizontal then the
trace is deflected in
• a) horizontal axis
• b) circular motion
• c) vertical axis
10. The name given to the joining of two fibre optic cables by aligning them carefully and bringing
them into close proximity of each other is
• a) Fusion
• b) End to end
• c) Lens Coupling
Question :1
The correct answer is c JAR OPS Supbart K 1.715 e
Question :2
The correct answer is c
Question :3
The correct answer is a
Question :4
The correct answer is b Binary Word is 11 - 28. BCD Word is 11 - 29
Question :5
The correct answer is b Answer found in Boeing SWPM. 20-41-01 3(2) (e) Hold the red lead of the (test)
meter between the forefinger and the thumb. The acceptable range is less than 10,000,000 ohms
Question :6
The correct answer is c The exact definition of HIRF does not include electrostatc discharge (ESD). But
only interference from outside sources. Understanding HIRF By Gerald L. Fuller
Question :7
The correct answer is a
Question :8
The correct answer is c
Question :9
The correct answer is a
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is b Introduction to Fiber Optics John Crisp page 189
4 An analogue to digital converter where it counts up to binary state eciual to the analogue in
put and then back down when this is reached is a
% a) successive approximation counter
• b) a tracking ramp type converter
• c) flash type converter
8. Op amps generally used in ADCs and DACs are normally % a) high input impedance, low
output impedance
• b) high input impedance , high output impedance % c) low input impedance , how output
impedance
Question :1
The correct answer is b Introduction to Fiber Optics John Crisp page 189
Question :2
The correct answer is c
Question :3
The correct answer is b
Question :4
The correct answer is b Digital Fundimentals T L Floyd page 571
Question :5
The correct answer is c
Question :6
The correct answer is b
Question :7
The correct answer is c
Question :8
The correct answer is a
Question :9
The correct answer is b
Question :10
The correct answer is b Basic Electronics Malcolm Plant Page 16D
Practice Exam
Module 5
Stopwatch
Start at
1. A parallel register
• a) reads each bit to be stored simultaneously
b) requires a clock pulse for each bit
• c) reads the stored data when logic 0 is applied to the read line
The correct answer is a The exact definition of HIRF does not include static build-up, but does include
interference from outside sources. The protection from such interferenc is via the aircraft skin and
wire/LRU shielding. Understanding HIRF, Gerald L Fuller
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 132
•
a) A or B = 1
• b) A and B = 1
• c) A and B = 0
• a) NAND Gate
• b) NOR gate
• c) AND gate
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 128
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 128
8. What systems use base 16?
• a) Octal
• b) BCD
• c) Hexadecimal
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 132
The correct answer is a Aircraft Instruments and Integrated Systems EHJ Pallett Page 300
The correct answer is a The outer cladding is glass, so it is refractive (but less so than the core). Cladding
causes Total Internal Reflection (TIR), so question can be interpreted in two ways.
Question :1
The correct answer is a
Question :2
The correct answer is a The exact definition of HIRF does not include static build-up, but does include
interference from outside sources. The protection from such interferenc is via the aircraft skin and
wire/LRU shielding. Understanding HIRF, Gerald L Fuller
Question :3
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 132
Question :4
The correct answer is c
Question :5
The correct answer is c
Question :6
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 128
Question :7
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 128
Question :8
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 132
Question :9
The correct answer is a Aircraft Instruments and Integrated Systems EHJ Pallett Page 300
Question :10
The correct answer is a The outer cladding is glass, so it is refractive (but less so than the core). Cladding
causes Total Internal Reflection (TIR), so question can be interpreted in two ways.
Practice Exam
Module 5
Stopwatch
Start at
2. Analogue logic 1 is
• a) closed switch, Logic Q=0
• b) closed circuit, Logic Q=1
• c) open circuit
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 148
6. The "light" emitted from a LED used within a fibre-optic system will have a wavelength
• a) slightly longer then that of visible light
• b) slightly shorter then that of visible light
• c) equal to that of visible light
The correct answer is a Infrared from 850nm. Visible light is 400 - 800 nm
9. Fibre optic cable over copper cable has the following advantages
• a) non-conductive, easier to manufacture and assemble, greater bandwidth
• b) non-conductive, greater bandwidth, greater signal security
• c) greater bandwidth, greater signal security, more robust
Question :1
The correct answer is a
Question :2
The correct answer is b
Question :3
The correct answer is a Aircraft Electricity and Electronics Eismin 5th Edition Page 148
Question :4
The correct answer is c
Question :5
The correct answer is b
Question :6
The correct answer is a Infrared from 850nm. Visible light is 400 - 800 nm
Question :7
The correct answer is a
Question :8
The correct answer is a
Question :9
The correct answer is b
Question :10
The correct answer is c
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is a Convert it to Decimal first (15 x 256 + 8 x 16 + 6 x 1) = 3974. Since it is an even
number, it must be the answer with a zero on the end.
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 1129
3. During normal functioning of an ECAM system the engine data shown on the
Engine/Warning display comes from the
a) EFIS channel of DMC3
b) ECAM channel of DMC1
c) ECAM channel of DMC3
The correct answer is b DMC 1 (in normal operation) supplies info the the upper ECAM, DMC 2 supplies
info to the lower ECAM and DMC 3 is in standby
The correct answer is c Aircraft Instruments and Integrated Systems EHJ Pallett Page 254
8. For an IRS System to pass the ‘Alignment System Performance Test’ the
a) entered present latitude and longitude must agree with the latitude and longitude
at last power down
b) the No 1 and No 2 must both have the same latitude and longitude present
position entered
c) the latitude entered must be within given limits of the latitude computed by IRU
The correct answer is c Aircraft Intruments and Integrated Systems, Pallett pages 279-280
10. Control Display Unit (CDU ) selection of TKE (Track Angle Error), displays
a) distance perpendicular from the selected track
b) difference in degrees that the aircraft is to the right or left of the desired track
c) difference in degrees from True North in a clockwise direction from the desired
track
The correct answer is b Aircraft Instruments and Integrated Systems EHJ Pallett Page 256
How did you do?
------------------------------------
Question :1
The correct answer is a Convert it to Decimal first (15 x 256 + 8 x 16 + 6 x 1) = 3974. Since it is an even
number, it must be the answer with a zero on the end.
Question :2
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 1129
Question :3
The correct answer is b DMC 1 (in normal operation) supplies info the the upper ECAM, DMC 2 supplies
info to the lower ECAM and DMC 3 is in standby
Question :4
The correct answer is b
Question :5
The correct answer is b Jeppesen Avionics Fundamentals Page 132
Question :6
The correct answer is a
Question :7
The correct answer is c Aircraft Instruments and Integrated Systems EHJ Pallett Page 254
Question :8
The correct answer is c Aircraft Intruments and Integrated Systems, Pallett pages 279-280
Question :9
The correct answer is c
Question :10
The correct answer is b Aircraft Instruments and Integrated Systems EHJ Pallett Page 256
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 44. You've been here 1 times.
1. In the EICAS system, when is the maintenance mode available?
a) On the upper and lower screens - only available on the ground
b) Lower screen only - only available on the ground
c) In flight
The correct answer is b B747 Maintenance Manual. Aircraft Instruments and Integrated Systems. Pallett
Page 380
The correct answer is c Aircraft Electricity and Electronics, 5th edition, Eismin, Pages 152 and 268
The correct answer is a Aircraft instruments and integrated systems (Pallett), page 286
The correct answer is a Aircraft Instruments and Integrated Systems EHJ Pallett Page 260
The correct answer is c Aircraft Instruments and Integrated Systems EHJ Pallett Page 256
The correct answer is c Aircraft Instruments and Integrated Systems EHJ Pallett Page 280
Question :1
The correct answer is b B747 Maintenance Manual. Aircraft Instruments and Integrated Systems. Pallett
Page 380
Question :2
The correct answer is c Aircraft Electricity and Electronics, 5th edition, Eismin, Pages 152 and 268
Question :3
The correct answer is a Aircraft instruments and integrated systems (Pallett), page 286
Question :4
The correct answer is a Aircraft Instruments and Integrated Systems EHJ Pallett Page 260
Question :5
The correct answer is b Jeppesen Avionics Fundamentals Page 134
Question :6
The correct answer is c Jeppesen Avionics Fundamentals Page 138
Question :7
The correct answer is c Aircraft Instruments and Integrated Systems EHJ Pallett Page 256
Question :8
The correct answer is b Aircraft Instruments and Integrated Systems EHJ Pallett Page 247 fig 10.1.
Jeppesen Avionics Fundamentals Page 137 & 138
Question :9
The correct answer is b Jeppesen Avionics Fundamentals Page 135
Question :10
The correct answer is c Aircraft Instruments and Integrated Systems EHJ Pallett Page 280
Practice Exam
Module 5
Stopwatch
Start at
2. The control of the speed or rate that the F/D Command bars move can be controlled by
a) position feedback
b) rate or velocity feedback
c) amplifier gain
3. The Centralized Aircraft Monitoring System uses the maintenance mode of operation
a) in the air only
b) on the ground only
c) either ground or air
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 146
5. Can an LRU transmit and receive on more than one 629 bus?
a) Yes
b) No
c) Only if paralleled
Question :1
The correct answer is b
Question :2
The correct answer is b
Question :3
The correct answer is b
Question :4
The correct answer is c Aircraft Electricity and Electronics Eismin 5th Edition Page 146
Question :5
The correct answer is a
Question :6
The correct answer is b Aircraft Electricity and Electronics Eismin 5th Edition Page 149
Question :7
The correct answer is a
Question :8
The correct answer is a
Question :9
The correct answer is b
Question :10
The correct answer is a
Practice Exam
Module 5
Stopwatch
Start at
1. A BCD word occupies bits 11-29, if 11-15 are filled with padders then the LSB of the word will be
a) 16
b) 29
c) 11
The correct answer is c Digital Avionic Systems - Cary Spitzer. Page 109, Arinc report 604 guidance for
design and use of built in test equipment states... 'BITE should excercise the hardware sufficiently to
determine if it meets the performance requirements but should not drive it against mechanical stops.'
The correct answer is c Boeing 757 MM 34-22-00 page 8 paragraph G (EADI), Section (2)........'It (the
CRT) utilizes magnetic deflection and electrostaic focus control.'
Question :1
The correct answer is a
Question :2
The correct answer is a
Question :3
The correct answer is b
Question :4
The correct answer is c Digital Avionic Systems - Cary Spitzer. Page 109, Arinc report 604 guidance for
design and use of built in test equipment states... 'BITE should excercise the hardware sufficiently to
determine if it meets the performance requirements but should not drive it against mechanical stops.'
Question :5
The correct answer is a
Question :6
The correct answer is a
Question :7
The correct answer is a
Question :8
The correct answer is c Boeing 757 MM 34-22-00 page 8 paragraph G (EADI), Section (2)........'It (the
CRT) utilizes magnetic deflection and electrostaic focus control.'
Question :9
The correct answer is b
Question :10
The correct answer is b
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 47. You've been here 1 times.
1. L.E.D.s can give
a) high definition displays
b) red and green displays only
c) monochrome displays only
The correct answer is c LEDs can only ever give one colour (i.e. monochrome) as the colour is determined
by the doping element and nothing else. LEDs which appear to give two colours are actually two separate
LEDs in the same case.
The correct answer is c Introduction to Fiber Optics John Crisp page 189
4. For large bandwidth high-speed fibre optic transmission what sort of cable would you
use?
a) Single mode
b) Graded index
c) Step index
7. What is the advantage of an ILD over an LED when used as a light source in fibre optics
a) higher bandwidth
b) lower frequency range
c) lower intensity
The correct answer is b Introduction to Fiber Optics John Crisp. A Laser Diode has a lower spectrum of
frequencies hence reduce chromatic dispersion.
a) CD ROM
b) IC
c) magnetic tape
9. A typical example of an IC is
a) ALU
b) CPU
c) dip switch
Question :1
The correct answer is c LEDs can only ever give one colour (i.e. monochrome) as the colour is determined
by the doping element and nothing else. LEDs which appear to give two colours are actually two separate
LEDs in the same case.
Question :2
The correct answer is c Introduction to Fiber Optics John Crisp page 189
Question :3
The correct answer is a CAAIPs Leaflet 9-4 8.1 (a)
Question :4
The correct answer is a
Question :5
The correct answer is a Basic Electronics Malcolm Plant Page 60D
Question :6
The correct answer is b
Question :7
The correct answer is b Introduction to Fiber Optics John Crisp. A Laser Diode has a lower spectrum of
frequencies hence reduce chromatic dispersion.
Question :8
The correct answer is a
Question :9
The correct answer is b
Question :10
The correct answer is c
Practice Exam
Module 5
Stopwatch
Start at
The correct answer is b Fiber Optics Communication and Other Applications Page 15
2. A device, which converts serial to parallel and parallel to serial for arithmetical functions, is
a) 0, 1
b) 1, 1
c) 1, 0
The correct answer is b Fiber Optics Communication and Other Applications Page 46/7. Presumably, this
means the MAXIMUM angle of incidence.
7. A fibre optic cable is connected to a unit that will not be frequently disconnected. The preferred
type of connector to be used is a
a) Ball lens type
b) Butt type
c) Quick disconnect type
The correct answer is b Aircraft Electricity and Electronics, Eismin, 5th Edition. Pg 154
Question :1
The correct answer is b Fiber Optics Communication and Other Applications Page 15
Question :2
The correct answer is b Pulse code modulation/parallel to serial
Question :3
The correct answer is c Octal 320 converted to binary.
Question :4
The correct answer is a Check out the table on http://www.play-hookey.com/digital/adder.html
Question :5
The correct answer is c Check out the table on http://www.play-hookey.com/digital/adder.html
Question :6
The correct answer is b Fiber Optics Communication and Other Applications Page 46/7. Presumably, this
means the MAXIMUM angle of incidence.
Question :7
The correct answer is b Boeing 777-200 training notes
Question :8
The correct answer is b Aircraft Electricity and Electronics, Eismin, 5th Edition. Pg 154
Question :9
The correct answer is a
Question :10
The correct answer is a Basic Electronics Malcolm Plant Page 87E
49,
1. A CRT is
a) electromagnetic
b) electrostatic
c) solid state
The correct answer is a A CRT is NOT solid state. Most CRTs used on aircraft are electromagnetic.
3. What is 44 in hexadecimal?
a) 2c
b) 2d
c) 2F
The correct answer is b Aircraft Instruments and Integrated Systems, Pallett. Page 153
The correct answer is c Aircraft Instruments and Integrated Systems, Pallett. Page 153
The correct answer is a An LCD display uses only red, green and blue filters. By mixing them, it can get
different colours, but not an infinite amount.
Question :1
The correct answer is a A CRT is NOT solid state. Most CRTs used on aircraft are electromagnetic.
Question :2
The correct answer is c Decimal is a power of 10 counting system
Question :3
The correct answer is a (2 x 16) + (12 x 1) = 44 (c = 12)
Question :4
The correct answer is c Octal 33 = (3 x 8) + (3 x 1) = 27 decimal. 27 = (1 x 16) + (11 x 1) = 1b (b = 11)
Question :5
The correct answer is b See http://www.arundisplay.co.uk/glossary/lcd_technology.htm
Question :6
The correct answer is a See http://www.lgeservice.com/monterms.html for definition of resolution (pixels
per inch) and triads. The actual figure of 84 is irrelevant (as there are many different CRT resolutions). The
question is asking whether you know the definition of resolution
Question :7
The correct answer is a
Question :8
The correct answer is b Aircraft Instruments and Integrated Systems, Pallett. Page 153
Question :9
The correct answer is c Aircraft Instruments and Integrated Systems, Pallett. Page 153
Question :10
The correct answer is a An LCD display uses only red, green and blue filters. By mixing them, it can get
different colours, but not an infinite amount.
50
3. What is the device used to convert Binary Coded Decimal into separate supplies for a seven segment
digital display?
a) Multiplexer
b) Demultiplexer
c) Decoder
The correct answer is c RS catalogue...part number CA3161 (see www.RSwww.com website and enter the
part number in their search box)
The correct answer is b Pallett Aircraft instuments & Integrated Systems Page 153
The correct answer is a E-OR is another name for XOR (in the twisted CAA mind!)
The correct answer is b Pallet Aircraft Electrical System 3rd Edition page 72. Trick question, it is a DC
interlock
Question :1
The correct answer is b
Question :2
The correct answer is a
Question :3
The correct answer is c RS catalogue...part number CA3161 (see www.RSwww.com website and enter the
part number in their search box)
Question :4
The correct answer is b
Question :5
The correct answer is b Pallett Aircraft instuments & Integrated Systems Page 153
Question :6
The correct answer is a E-OR is another name for XOR (in the twisted CAA mind!)
Question :7
The correct answer is a
Question :8
The correct answer is a Jeppesen Avionics Fundamentals Page 218
Question :9
The correct answer is b Pallet Aircraft Electrical System 3rd Edition page 72. Trick question, it is a DC
interlock
Question :10
The correct answer is a
51
Practice Exam
Module 5
Stopwatch
Start at
8. In a colour cathode ray tube, how is the phosphor arranged in the tube?
a) A red layer on the front with two green layers behind it
b) Layers of red, blue and green
c) A single phosphor layer containing red, green and blue
10. An 8 data input multiplexer has how many Data select lines
a) 3
b) 2
c) 8
Question :1
The correct answer is b
Question :2
The correct answer is b
Question :3
The correct answer is a
Question :4
The correct answer is c
Question :5
The correct answer is c
Question :6
The correct answer is c
Question :7
The correct answer is b Digital Fundamentals by Thomas L Floyd
Question :8
The correct answer is c Success in Electronics By Tom Duncan p285
Question :9
The correct answer is c LCDs have 3 colours (RGB) which can be blended to make other colours (of
limited number)
Question :10
The correct answer is a Digital Fundamentals by Thomas L Floyd p328
Practice Exam
Module 5
Start at
The correct answer is b Automatic Flight Control by EHJ Pallett and Shawn Coyle page 268
a) 101 011
b) 110 111
c) 111 111
a) Matrix LCD
b) Capacitor
c) LED
4. A priority encoder
The correct answer is c See ARINC 429 tutorial (in FORUM module 5).
The correct answer is a 12-bit label field, 4-bit label extension, single parity, 3-bit time hi-lo synch pulse.
20 bit in total
9. Which of the following ESDS devices can withstand higher static electricity voltage?
a) ECL
b) MOSFET
c) SCR
Question :1
The correct answer is b Automatic Flight Control by EHJ Pallett and Shawn Coyle page 268
Question :2
The correct answer is c
Question :3
The correct answer is b
Question :4
The correct answer is b
Question :5
The correct answer is b
Question :6
The correct answer is c See ARINC 429 tutorial (in FORUM module 5).
Question :7
The correct answer is a 8 bits per byte
Question :8
The correct answer is a 12-bit label field, 4-bit label extension, single parity, 3-bit time hi-lo synch pulse.
20 bit in total
Question :9
The correct answer is c
Question :10
The correct answer is a
Practice Exam
Module 5
Stopwatch
Start at
3. A backlighted LCD
• a) has infinite colours
• c) has only 3 colours
The correct answer is c A backlighted LCD has only 3 colours (RGB) but can mix them to make others (but
not an infinite amount)
The correct answer is c A DIP switch is not an IC. ALU is an integrated part of the CPU. The
'Control Processor Unit' is another term used for the 'Central Processor Unit (CPU)' or sometimes a
switching unit used in telegraphy (such as the touchpad of a telephone) - the latter would be an SSI (defined
as containing up to 100 transistors or gates).
5. The smallest operation possible in a computer is the
a) timing cycle
• b) processor sub-cycle
• c) processor cycle
The correct answer is c Ferromagnetic material is that which hard-drives and floppy drives are made from
8. An aircraft on an ILS approach is below the glideslope centre line, the glideslope pointer is
• a) above the centre line
• b) below the centre line
• c) level with the datum
The correct answer is a Aircraft Instruments and Integrated Systems Pallett Pages 13 - 15 (Although, in the
real world, others are available too).
Question :1
The correct answer is c
Question :2
The correct answer is c
Question :3
The correct answer is c A backlighted LCD has only 3 colours (RGB) but can mix them to make others (but
not an infinite amount)
Question :4
The correct answer is c A DIP switch is not an IC. ALU is an integrated part of the CPU. The
'Control Processor Unit' is another term used for the 'Central Processor Unit (CPU)' or sometimes a
switching unit used in telegraphy (such as the touchpad of a telephone) - the latter would be an SSI (defined
as containing up to 100 transistors or gates).
Question :5
The correct answer is a Also known as the clock pulse
Question :6
The correct answer is c Ferromagnetic material is that which hard-drives and floppy drives are made from
Question :7
The correct answer is a
Question :8
The correct answer is a
Question :9
The correct answer is a Aircraft Instruments and Integrated Systems Pallett Pages 13 - 15 (Although, in the
real world, others are available too).
Question :10
The correct answer is c
Practice Exam
Module 5
Stopwatch
Start at
5. TheTX/RXofArinc629is
• a) encoder/decoder
• b) multiplex/de-multiplex
• c) switching
The correct answer is c Aicraft Electricity and Electronics, Eismin 5th Ed, pg149
7. DRAM
• a) requires a refreshing charge
b) memory is stored when power supply is removed
c) it does not require a refreshing charge
Question :1
The correct answer is a
Question :2
The correct answer is b
Question :3
The correct answer is c
Question :4
The correct answer is a
Question :5
The correct answer is b
Question :6
The correct answer is c Aicraft Electricity and Electronics, Eismin 5th Ed, pg149
Question :7
The correct answer is a http://computer.howstuffworks.com/ram4.htm
Question :8
The correct answer is c
Question :9
The correct answer is b
Question :10
The correct answer is a Probably referring to a comparator feedback circuit.
Practice Exam
Module 5
Stopwatch
Start at
This is exam number 55 You've been here 1 times
1. A BITE check for automatic performance and fault monitoring is carried out when?
• a) Power-up self test
• b) For in-flight monitoring
• c) To check the performance of the LRU
7. In a computer, the code that fetches correct data and feeds it to the ALU is called
a) the computer program
• b) the instruction set
• c) ARINC
8. What is this?
a) Multiplexor
b) Shift register
c) Counter
Question :1
The correct answer is a
Question :2
The correct answer is c
Question :3
The correct answer is a
Question :4
The correct answer is c
Question :5
The correct answer is b Introduction to Fiber Optics John Crisp page 29
Question :6
The correct answer is b
Question :7
The correct answer is b http://www.webopedia.com/TERM/I/instruction.html
Question :8
The correct answer is a
Question :9
The correct answer is a (closest answer) See www.tpub.com/neets/book22/92a.htm
Question :10
The correct answer is a
Practice Exam
Module 5
Stopwatch
Start at
1. A dynamic EPROM
• a) requires constant refreshing
b) is non-volatile memory
c) is erased after reading
4. when using aTDR (time delay reflecto meter) the loss value of the cable is:
• a) set on the TDR
• b) shown by the curve
• c) allowed for in the calculation
Question :1
The correct answer is a
Question :2
The correct answer is a
Question :3
The correct answer is a
Question :4
The correct answer is b http://www.tscm.com/riapp1.html
Question :5
The correct answer is b Intensity of light cannot be changed with an LED
Question :6
The correct answer is b
Question :7
The correct answer is a
Question :8
The correct answer is b
Question :9
The correct answer is a
Question :10
The correct answer is a http://www.cs.umd.edu/class/spring2003/cmsc311/Notes/CompOrg/tristate.html
Practice Exam
Module 5
Stopwatch
Start at
Question :1
The correct answer is b
Question :2
The correct answer is b
Question :3
The correct answer is b
Question :4
The correct answer is b
Question :5
The correct answer is b Introduction to Fiber Optics John Crisp Page 65
Question :6
The correct answer is c
Question :7
The correct answer is b No correct answer here, as 561 is for INS.
Question :8
The correct answer is b
Question :9
The correct answer is c
Question :10
The correct answer is a
Practice Exam
Module 5
Start at
3. A humid atmosphere
a) eliminates static charge
• b) reduces static charge
c) has no effect on the level of charge
5. The arithmetic logic unit (ALU) in a central processor unit (CPU) carries out
• a) addition, subtraction, multiplication and division
• b) timing and synchronisation
c) computations as instructed
Question :1
The correct answer is a
Question :2
The correct answer is c
Question :3
The correct answer is b
Question :4
The correct answer is a
Question :5
The correct answer is c
Question :6
The correct answer is c
Question :7
The correct answer is c
Question :8
The correct answer is b
Question :9
The correct answer is a
Question :10
The correct answer is c
Practice Exam
Module 5
Stopwatch
Start at
2. An asynchronous system
• a) uses a clock pulse after a settling time to input data
• b) provides data real-time without the need for a clock pulse
• c) both a and b depending on the system
Question :1
The correct answer is a
Question :2
The correct answer is b
Question :3
The correct answer is c
Question :4
The correct answer is c
Question :5
The correct answer is a Flight Instruments and Automatic Flight Control Systems 6th Edition David Harris
Page 172
Question :6
The correct answer is b
Question :7
The correct answer is c
Question :8
The correct answer is b
Question :9
The correct answer is c
Question :10
The correct answer is