Professional Documents
Culture Documents
Description
The STPM33 energy metering evaluation board is
a class 0.2, single-phase meter which includes
tamper monitoring, CT and shunt current sensors
for power line systems with Vnom = 140 to
300 V(RMS), Inom / Imax = 5/100 A(RMS), flin = 50/60
Hz ± 10% and Tamb = -40 to +85 °C.
Measured active/reactive power can be output
from two programmable LEDs on the board.
The board can be interfaced with a PC running
evaluation software through an isolated RS232
port, or through the STEVAL-IPE023V1 USB
isolated interface tool for configuration and data
Features reading.
The board also has SPI/UART pins available to
• 0.2% accuracy single-phase meter with tamper
interface a microcontroller for application
monitoring
development.
• Vnom(RMS) = 140 to 300 V, Inom/Imax(RMS) =
5/100 A, flin = 50/60 Hz ± 10%
• Tamper detection though neutral current
monitoring
• Connector for USB isolated hardware
programmer tool STEVAL-IPE023V1 and PC
GUI
• RS232 and UART isolated connectors to PC
GUI
• SPI/UART switch for device peripheral
selection
• 2 programmable LEDs on board
• Digital expansion to external system-on-chip or
MCU
• 3.3 V power supply: external or through
STEVAL-IPE023V1 isolated USB board
• IEC61000 standard compliant
• RoHS compliant
1 Schematic diagrams
1 RXD
2 TXD
3 +3.3VDC
4 GND
NOTE: always provide supply
for both RS232 and UART
1
5
J2
J1 RS-232 DB9
UART I/O
Vcc
6
4
3
2
1
C6 C7
C1 1 Vcc 10K
C1+
100n 3
C1-
C2 4
C2+
100n 5
C2-
C3 2
V+
2
100n 6
V-
C4 J3
100n 16 15 RS-232 enable
VCC GND
1
MAX3232/SO
C5
100n
GALVANIC ISOLATION
GIPG25032014DI1530
1
3
5
7
9
6 SCL
DL2 LED2 C11 150p 7 NC
R6
SPI 8 SYN
4.7K
J6 9 NC
C12 150p
R5 10 Vcc
10
2
4
6
8
4.7K
C13 150p Vcc J7
DC Supply
C18
J5 C19 C20
C14 150p
R11
2 1 RXD 100n 4.7u
150p
Vref1
4 3 C15 150p
1
2
100R
TXD
6 5
8 7
C21
C22 C23
Vcc
2
100n 100u 10V J11
150p
DIGITAL I/O
32
31
30
29
28
27
26
25
Vref 1-2
C16 Ex
Ex
1 Int1 15p
1
GNDD
GNDD-NC
VDDD
Y1
SYN
MISO
MOSI
SCS
SCL
2 Int2
3 Led2 R4 1 24
CKout/ZCR NC Vref2
4 En/Rst 1M 2 23
16MHz XTAL2 VCC
5 Led1 C17 3 22
6 Gnd CKin/XTAL1 U3 GNDreg
15p 4 21
LED1 VDDA
C28
C29
C30
7 Ckin 5 STPM33/34 20
8 Ckout/ZCR LED2 GNDA
6 19 Vref2
INT1 VREF2
C31
C32
7 18
1u
150p
100n
INT2 GNDref
8 17 Vref1
VN2/NC
EN VREF1
VP2/NC
C26
C27
150p
100n
VN1
VP1
IN1
IN2
IP1
IP2
150p
100n
100R R3
10
11
12
13
14
15
16
9
3 Vcc
3 C8 C9
R2 R14 Vp1 Vp2 R25
J4 2 270K 270K
2 100n 150p
22K R13 C24 R15 R26 C34 R24
1 270K
1
270K 22n 470R 470R 22n
Vn1
Vn2
Enable/RST Do not assemble in case STPM33
R12 R23
270K
J9 J10
270K
1 line2 1
L1 L7
1500ohm 1500ohm
L1 L2
R17 Ip1 Ip2 R20
L3 L5
VAC 4626-X002 1K 1K T2
1500ohm 1500ohm
J8
RS1 R16
C25 C33
1 BKW-M-R0003-5.0 R21
L2
6R 6R
10n 10n
1500ohm T1 VAC 4626-X002
N
R19 R18 In1 In2 R22
L4 L6
0R 1K 1K
1500ohm 1500ohm
GIPG25032014DI1535
2 Revision history
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
www.DatasheetCatalog.com