Professional Documents
Culture Documents
JIS H 3100-2012-Unlocked PDF
JIS H 3100-2012-Unlocked PDF
INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association
(JCBA/JSA)
Copper and copper alloy sheets,
plates and strips
ICS 77.150.30
Reference number: JIS H 3100 : 2012 (E)
PROTECTED BY COPYRIGHT 23 S
H 3100 : 2012
© JSA 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or
utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
Printed in Japan
KAIAT
PROTECTED BY COPYRIGHT
H 3100: 2012
Contents
Page
(i)
PROTECTED BY COPYRIGHT
H 3100: 2012
Foreword
This translation has been made based on the original Japanese Industrial Standard
revised by the Minister of Economy, Trade and Industry through deliberations at
the Japanese Industrial Standards Committee as the result of proposal for revision
of Japanese Industrial Standard submitted by Japan Copper and Brass Association
(JCBA)/Japanese Standards Association (JSA) with the draft being attached, based
on the provision of Article 12 Clause 1 of the Industrial Standardization Law applicable
to the case of revision by the provision of Article 14.
Consequently JIS H 3100: 2006 is replaced with this Standard.
However, JIS H 3100: 2006 may be applied in the JIS mark certification based on
the relevant provisions of Article 19 Clause 1, etc. of the Industrial Standardization
Law until October 21, 2013.
This JIS document is protected by the Copyright Law.
Attention is drawn to the possibility that some parts of this Standard may conflict
with a patent right, application for a patent after opening to the public or utility
model right. The relevant Minister and the Japanese Industrial Standards Committee
are not responsible for identifying the patent right, application for a patent after
opening to the public or the utility model right.
(ii)
PROTECTED BY COPYRIGHT
JAPANESE INDUSTRIAL STANDARD JIS H 3100 : 2012
1 Scope
This Japanese Industrial Standard specifies the rolled copper and copper alloy sheets
and plates (hereafter referred to as "plates") and strips (hereafter referred to as "strips")
(excluding the copper and copper alloy plates and strips specified in JIS H 3110, JIS
H 3130 and JIS H 3510).
NOTE: Circular plates which are machined, punched or sheared from plates and
strips are included.
2 Normative references
The following standards contain provisions which, through reference in this text,
constitute provisions of this Standard. The most recent editions of the standards
(including amendments) indicated below shall be applied.
JIS H 0321 General rules for inspection of non-ferrous metal materials
JIS H 0500 Glossary of terms used in wrought copper and copper alloys
JIS H 0501 Methods for estimating average grain size of wrought copper and cop-
per alloys
JIS H 0505 Measuring methods for electrical resistivity and conductivity of non-
ferrous materials
JIS H 1051 Methods for determination of copper in copper and copper alloys
JIS H 1052 Methods for determination of tin in copper and copper alloys
JIS H 1053 Methods for determination of lead in copper and copper alloys
JIS H 1054 Methods for determination of iron in copper and copper alloys
JIS H 1055 Methods for determination of manganese in copper and copper alloys
JIS H 1056 Methods for determination of nickel in copper and copper alloys
JIS H 1057 Methods for determination of aluminium in copper and copper alloys
JIS H 1058 Methods for determination of phosphorus in copper and copper alloys
JIS H 1062 Methods for determination of zinc in copper and copper alloys
JIS H 1074 Copper and copper alloys-Determination of zirconium content
JIS H 1292 Methods for X-ray fluorescence spectrometric analysis of copper alloys
JIS Z 2241 Metallic materials-Tensile testing-Method of test at room tempera-
ture
JIS Z 2244 Vickers hardness test-Test method
JIS Z 2248 Metallic materials-Bend test
PROTECTED BY COPYRIGHT
2
H 3100 : 2012
PROTECTED BY COPYRIGHT
3
H 3100: 2012
Table 1 (continued)
Grade Class Designa- Informative
tion
Alloy Shape Name Characteristics and application examples
No.
C 2051 Strip Common C 2051 R Copper for Excellent drawability.
detonator Applicable to detonators.
C 2100 Plate Common C 2100 P Red brass Fine gloss, good workability, drawability and
weathering resistance.
Strip Common C 2100 R
Applicable to buildings, personal accessories,
Special C 2100 RS cosmetic cases, etc.
C 2200 Plate Common C 2200 P
Strip Common C 2200 R
Special C 2200 RS
C 2300 Plate Common C 2300 P
Strip Common C 2300 R
Special C 2300 RS
C 2400 Plate Common C 2400 P
Strip Common C 2400 R
Special C 2400 RS
C 2600 Plate Common C 2600 pal Brass Excellent workability and drawability, and good
a properties on plating.
Strip Common C 2600 R )
Applicable to terminal connectors, etc.
Special C 2600 RS a )
C 2680 Plate Common C 2680 pal Good workability, drawability and good proper-
a ties on plating.
Strip Common C 2680 R )
Intended for use in deep drawing work such as
Special C 2680 RS a ) snap buttons, cameras, thermos bottles.
Applicable to terminal connectors and wiring
appliances, etc.
C 2720 Plate Common C 2720 P Good workability and drawability.
Strip Common C 2720 R Intended for use in shallow drawing work, etc.
Special C 2720 RS
C 2801 Plate Common C 2801 pal High strength and moderate workability.
Strip Common C 2801 R a
)
Applicable to parts of wiring appliances used as
punched or in a bent state, name plates, instru-
Special C 2801 RS a ) ment panels, etc.
C 3710 Plate Common C 3710 P Free cutting Excellent punchability, and good machinability.
brass Applicable to clock parts, gears, etc.
Strip Common C 3710 R
C 3713 Plate Common C 3713 P
Strip Common C 3713 R
C 4250 Plate Common C 4250 P Tin- Good stress corrosion cracking resistance, wear
containing resistance and spring behaviours.
Strip Common C 4250 R
brass Applicable to switches, relays, connectors and
Special C 4250 RS various spring parts, etc.
PROTECTED BY COPYRIGHT
4
H 3100 : 2012
5 Quality
5.1 Appearance
Plates and strips shall have a workmanlike finish, homogeneity, and shall be free
from defects detrimental to practical use. The judgement of the defects detrimental
to practical use shall be subject to the agreement between the purchaser and the manu-
facturer.
PROTECTED BY COPYRIGHT
5
H 3100: 2012
0.15 0.050
e 1940 Residual 0.03 2.1 to - 0.05 to - - - 0.015 to For analysis
max. 2.6 0.20 0.150 ofeu:
eu+Pb+Fe+
Zn+P
99.8 min.
e 2051 98.0 to 0.05 0.05 - Residual - - - - -
PROTECTED BY COPYRIGHT
6
H 3100 : 2012
PROTECTED BY COPYRIGHT
7
H 3100: 2012
The hardness test shall be performed only when requested by the purchaser, and
the obtained result shall be reported as an informative value.
The proof stress of plates and strips to be used for pressure vessels shall be tested
by 7.2 and the results shall satisfy the requirements in table 4.
PROTECTED BY COPYRIGHT
8
H 3100 : 2012
Table 3 (continued)
Alloy Tem- Product Tensile test Bend test a) Hardness test
No. per designation (informative)
grade
Thickness Tensile Elon- Thick- Bend Inter- Thick- Vickers
strength gation ness angle nal ness hard-
radius ness b)
mm N/mm 2 % mm mm HV
0
C 1020 H C 1020 P-H 0.10 or over up 275 - 2.0 180 Thick- 0.20 80
C 1020 PS-H to and incl. 10 min. max. ness min. min. e)
X 1.5
C 1020 R-H 0.10 or over up
C 1020 RS-H to and incl. 4.0
PROTECTED BY COPYRIGHT
9
H 3100: 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
10
H 3100 : 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
11
H 3100: 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
12
H 3100 : 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
13
H 3100: 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
14
H 3100 : 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
15
H 3100: 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
16
H 3100 : 2012
Table 3 (continued)
H C 2720 P-H 0.30 or over up 410 - 2.0 180 0 Thick- 0.30 105
to and incl. 10 min. max. ness min. min.
x 1.5
C 2720 R-H 0.30 or over up
C 2720 RS-H to and incl. 3.0
PROTECTED BY COPYRIGHT
17
H 3100: 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
18
H 3100 : 2012
Table 3 (continued)
%H C 4250 P-%H 0.30 or over up 390 to 15 1.6 180 0 Thick- 0.30 110 to
to and incl. 20 480 min. max. ness min. 170
x2
C 4250 R-%H 0.30 or over up
C 4250 RS-%H to and incl. 3.0
:Y4H C 4250 P-:Y4 H 0.30 or over up 420 to 5 1.6 180 0 Thick- 0.30 140 to
to and incl. 20 510 min. max. ness min. 180
x 2.5
C 4250 R_3/4 H 0.30 or over up
C 4250 RS-:Y4 H to and incl. 3.0
H C 4250 P-H 0.30 or over up 480 to - 1.6 180 0 Thick- 0.30 140 to
to and incl. 10 570 max. ness min. 200
x3
C 4250 R-H 0.30 or over up
C 4250 RS-H to and incl. 3.0
PROTECTED BY COPYRIGHT
19
H 3100: 2012
Table 3 (continued)
PROTECTED BY COPYRIGHT
20
H 3100 : 2012
%H C 7250 PS-%H 0.10 or over up 410 to 5 1.0 180 0 Thick- 0.10 115 to
C 7250 RS-%H to and incl. 550 min. max. orW ness min. 180 c)
0.15 x 1
Over 0.15 up 9
to and incl. 1. 0 min.
H C 7250 PS-H 0.10 or over up 465 to 5 1.0 180 0 Thick- 0.10 140 to
C 7250 RS-H to and incl. 625 min. max. orW ness min. 210 c )
0.15 x 1
Over 0.15 up 7
to and incl. 1. 0 min.
EH C 7250 PS-EH 0.10 or over up 515 to 5 1.0 180 0 Thick- 0.10 160 to
C 7250 RS-EH to and incl. 1.0 655 min. max. orW ness min. 220 c )
x 1.5
EH C 7250 PS-SH 0.10 or over up 550 to 5 1.0 180 0 Thick- 0.10 170 to
C 7250 RS-SH to and incl. 1. 0 690 min. max. orW ness min. 230 c )
x 1.5
d)
Type of annealing
e)
Given greater tensile strength than SH by work-hardening.
f)
Given greater tensile strength than ESH by work-hardening.
PROTECTED BY COPYRIGHT
21
H 3100: 2012
PROTECTED BY COPYRIGHT
22
H 3100 : 2012
0.120
C 2680 P-O
0.050 0.035 0.070
C 2680 R-O, C 2680 RS-O
0.035 0.025 0.050
0.025 0.015 0.035
0.015 0.010 0.025
0.010 - 0.015
PROTECTED BY COPYRIGHT
23
H 3100: 2012
C 1020 0 C 1020 PC-O, C 1020 PSC-O 0.10 or over up to an d incl. 0.30 98 min.
C 1100 C 1020 RC-O, C 1020 RSC-O
Over 0.30 up to and incl. 0.50 99 min.
C 1100 PC-O, C 1100 PSC-O
C 1100 RC-O, C 1100 RSC-O Over 0.50 100 min.
%H C 1020 PC-%H, C 1020 PSC-%H 0.10 or over up to and incl. 2.0 97 min.
C 1020 RC-%H, C 1020 RSC-%H
C 1100 PC-%H, C 1100 PSC-%H Over 2.0 98 min.
C 1100 RC-%H, C 1100 RSC-%H
%H C 1020 PC-% H, C 1020 PSC-% H 0.10 or over up to and incl. 2.0 97 min.
C 1020 RC-% H, C 1020 RSC-% H
C 1100 PC-%H, C 1100 PSC-%H Over 2.0 98 min.
C 1100 RC-%H, C 1100 RSC-%H
H C 1020 PC-H, C 1020 PSC-H 0.10 or over up to and incl. 2.0 96 min.
C 1020 RC-H, C 1020 RSC-H
C 1100 PC-H, C 1100 PSC-H Over 2.0 97 min.
C 1100 RC-H, C 1100 RSC-H
C 1441 0 C 1441 PSC-O, C 1441 RSC-O 0.10 or over up to and incl. 3.0 78 min.
%H C 1441 PSC-%H, C 1441 RSC-%H
%H C 1441 PSC-% H, C 1441 RSC-% H
H C 1441 PSC-H, C 1441 RSC-H
C 1510 %H C 1510 PSC-%H, C 1510 RSC-%H 0.10 or over up to and incl. 3.0 90 min.
%H C 1510 PSC-%H, C 1510 RSC-%H
3/4 H C 1510 PSC_3/4H, C 1510 RSC-o/'4H
H C 1510 PSC-H, C 1510 RSC-H
EH C 1510 PSC-EH, C 1510 RSC-EH
SH C 1510 PSC-SH, C 1510 RSC-SH
C 1921 0 C 1921 PSC-O, C 1921 RSC-O 0.10 or over up to and incl. 3.0 85 min.
%H C 1921 PSC-%H, C 1921 RSC-%H
%H C 1921 PSC-%H, C 1921 RSC-%H
H C 1921 PSC-H, C 1921 RSC-H
SH C 1921 PSC-SH, C 1921 RSC-SH 0.10 or over up to and incl. 3.0 83 min.
C 1940 03 C 1940 PSC-03, C 1940 RSC-03 0.10 or over up to and incl. 3.0 60 min.
02 C 1940 PSC-02, C 1940 RSC-02
01 C 1940 PSC-01, C 1940 RSC-01
%H C 1940 PSC-% H, C 1940 RSC-% H
H C 1940 PSC-H, C 1940 RSC-H
EH C 1940 PSC-EH, C 1940 RSC-EH
SH C 1940 PSC-SH, C 1940 RSC-SH
ESH C 1940 PSC-ESH, C 1940 RSC-ESH
SSH C 1940 PSC-SSH, C 1940 RSC-SSH 0.10 or over up to and incl. 3.0 50 min.
Note a) lACS is the international annealed copper standard, of which the electric conductivity
is defined as being 100 %IACS.
PROTECTED BY COPYRIGHT
24
H 3100 : 2012
PROTECTED BY COPYRIGHT
25
H 3100: 2012
PROTECTED BY COPYRIGHT
26
H 3100 : 2012
Over 0.50 up to and incl. 0.80 ±0.04 ±0.06 ±0.08 ±0.10 ±0.15 - - - - -
Over 0.80 up to and incl. 1.2 ±0.05 ±0.08 ±0.10 ±0.12 ±0.16 - - - - -
Over 1.2 up to and incl. 2.0 ±0.06 ±0.10 ±0.12 ±0.15 ±0.18 ±0.28 ±0.35 - - -
Over 2.0 up to and incl. 3.2 ±0.08 ±0.12 ±0.15 ±0.18 ±0.22 ±0.33 ±OAO ±0.50 - -
Over 3.2 up to and incl. 5 ±0.10 ±0.15 ±0.18 ±0.22 ±0.28 ±OAO ±OA5 ±0.60 - -
Over 5 up to and incl. 8 ±0.13 ±0.18 ±0.23 ±0.26 ±0.34 ±OA5 ±0.55 ±0.80 - -
Over 8 up to and incl. 12 ±0.18 ±0.25 ±0.28 ±0.33 ±OAO ±0.60 ±0.70 ± 1.0 ± 1.3 ± 1.5
Over 12 up to and incl. 20 ±0.23 ±0.32 ±0.35 ±OAO ±0.50 ±0.75 ±0.85 ± 1.2 ± 1.5 ± 1.7
Over 20 up to and incl. 125 ±1.3 % ±1.8% ±2.2% ±2.5% ±3.3% ±3.8% ±4.3% ±6.0% ±7.5% ±8.5%
a) a) a) a) a) a) a) a) a) a)
PROTECTED BY COPYRIGHT
27
H 3100: 2012
Over 1.2 up to and incl. 2.0 ±0.12 ±0.17 ±0.20 ±0.24 ±0.30 - -
Over 2.0 up to and incl. 3.2 ±0.15 ±0.21 ±0.25 ±0.2S ±0.35 - -
Over S up to and incl. 12 ±0.50 ±0.50 ±0.60 ±0.70 ±0.70 ± 1.0 ± 1.2
Over 12 up to and incl. 20 ±0.70 ±0.70 ±O.SO ±O.SO ±O.SO ± 1.0 ± 1.2
Over 20 up to and incl. 35 ±0.90 ±0.90 ± 1.0 ± 1.0 ± 1.0 ± 1.2 ± 1.2
Over 35 up to and incl. 50 ± 1.1 ± 1.1 ± 1.2 ± 104 ± 104 ±1.6 ± 1.7
Over 50 up to and incl. 75 ± 1.3 ± 1.3 ± 104 ± 1.6 ± 1.6 ±3.5%aJ ±4.5 %a)
Over 75 up to and incl. 125 ± 1.5 ±1.5 ± 1.5 ± 1.6 ± 1.6 ±3.5%aJ ±4.5 %a)
Note a) The percentage values indicate the ratio to the thickness.
PROTECTED BY COPYRIGHT
28
H 3100 : 2012
[ Designations C 1020 RS, C 1100 RS, C 1201 RS, C 1220 RS, C 1441 RS,]
C 1510 RS, C 1921 RS, C 1940 RS, C 2100 RS, C 2200 RS,
C 2300 RS, C 2400 RS, C 2600 RS, C 2680 RS, C 2720 RS,
C 2801 RS, C 4250 RS, C 7250 RS
Unit: mm
Thickness Width
100 or under Over 100 up to Over 300 up to
and incl. 300 and incl. 700
0.10 or over up to and incl. 0.15 ±O.OOS ±0.010 ±0.015
Over 0.15 up to and incl. 0.25 ±0.010 ±0.015 ±0.020
Over 0.25 up to and incl. 0.35 ±0.015 ±0.020 ±0.025
Over 0.35 up to and incl. 0.50 ±0.020 ±0.025 ±0.030
Over 0.50 up to and incl. O.SO ±0.025 ±0.030 ±0.035
Over O.SO up to and incl. 1.2 ±0.030 ±0.035 ±0.040
Over 1.2 up to and incl. 2.0 ±0.040 ±0.045 ±0.050
Over 2.0 up to and incl. 3.0 ±0.050 ±0.055 ±0.060
PROTECTED BY COPYRIGHT
29
H 3100: 2012
PROTECTED BY COPYRIGHT
30
H 3100 : 2012
PROTECTED BY COPYRIGHT
31
H 3100: 2012
PROTECTED BY COPYRIGHT
32
H 3100 : 2012
0 0
Over 0.80 up to and incl. 8 +10 +15 - -
0 0
Over 8 up to and incl. 125 +15 +15 +20 +25
0 0 0 0
Camber (maximum
permissible value)
1000 mm
PROTECTED BY COPYRIGHT
33
H 3100: 2012
Flatness (maximum
permissible value)
Flat surface
PROTECTED BY COPYRIGHT
34
H 3100 : 2012
7 Tests
PROTECTED BY COPYRIGHT
35
H 3100: 2012
PROTECTED BY COPYRIGHT
36
H 3100 : 2012
Unit: mm
o (Upper-die)
N
o
N
35
2) The W bend test shall be performed by using the test jig of which the radius
does not exceed the internal radius of bend test specified in 5.4.
3) The test piece shall be placed on the under die of the test jig, and then with the
upper die applied onto the under die, pressed by hand or hydraulic pressure to
the specified form. In this case, the top surface of the upper die and the lower
bottom surface of the under die of the test jig shall be parallel to each other.
PROTECTED BY COPYRIGHT
37
H 3100: 2012
8 Inspection
The inspection shall be as follows.
a) General requirements shall be as specified in JIS H 0321.
b) Appearance shall comply with the specifications given in 5.1.
c) Chemical composition shall comply with the specifications given in 5.2.
d) Mechanical properties and other properties (grain size, electric conductivity and
volume resistivity, and hydrogen embrittlement) shall comply with the specifica-
tions given in 5.4 to 5.7.
e) Dimensions and dimensional tolerances shall comply with the specifications given
in clause 6.
9 Marking
Each package, coil or product of plates and strips shall be marked by a suitable
means such as labelling with the following information.
a) Number of this Standard and product designation (designation symbol and tem-
per grade)
Example: JIS H 3100 C 1020 PS-Y2H
b) Dimensions
Example 1 For plates 0.5 mm x 365 mm x 1 200 mm (thickness x width x
length)
Example 2 For strips 0.25 mm x 25.0 mm (thickness x width)
c) Manufacturing number
d) Manufacturer's name or its identifying brand
10 Report
The manufacturer shall submit, when requested at the time of order from the pur-
chaser, the report (certificate) containing the results of the test and/or inspection agreed
upon between the purchaser and the manufacturer.
PROTECTED BY COPYRIGHT
38
H 3100 : 2012
Annex A (informative)
Requirements of mechanical properties and
other properties
C 1201 0 -
0 6 D 6 - 6
C 1220 0 (*) 0 6 D 6 - -
C 1441 0 -
0 6 D - 6 -
C 1510 0 -
0 - D - 6 -
C 1921 0 -
0 6 D - 6 -
C 1940 0 -
0 - D - 6 -
C 2051 0 -
0 - - - - -
C 2100 0 -
0 6 - 6 - -
C 2200 0 -
0 6 - 6 - -
C 2300 0 -
0 6 - 6 - -
C 2400 0 -
0 6 - 6 - -
C 2600 0 -
0 6 D 6 6 -
C 2680 0 -
0 6 D 6 6 -
C 2720 0 -
0 6 D - - -
C 2801 0 -
0 6 D - 6 -
C 3710 0 -
0 - - - - -
C 3713 0 -
0 - - - - -
C 4250 0 -
0 6 D - - -
C 4450 0 -
0 - - - - -
C 4621 0 -
0 - - - - -
C 4640 0 (*) 0 - - - - -
C 6140 0 (*) 0 - - - - -
C 6161 0 -
0 6 - - - -
C 6280 0 -
0 - - - - -
C 7060 0 (*) 0 - - - - -
C 7150 0 (*) 0 - - - - -
C 7250 0 -
0 6 D - - -
PROTECTED BY COPYRIGHT
39
H 3100: 2012
Notes a) For the proof stress test for materials marked with (*), if requested by the purchaser,
JIS B 8265 or JIS B 8266 may be applied.
b) If the grain size requirement is applied, the tensile strength and elongation require-
ments need not be applied if so agreed between the purchaser and the manufacturer.
PROTECTED BY COPYRIGHT
40.
H 3100 : 2012
Annex B (informative)
Representative dimensions of plates and representative
internal diameters of coil of strips
The representative dimensions of plates are shown in table B.1, and the represen-
tative internal diameters of standard coil of strips are shown in table B.2 for reference.
Bibliography
JIS B 8265 Construction of pressure vessel-General principles
JIS B 8266 Alternative standard for construction of pressure vessels
PROTECTED BY COPYRIGHT
Errata for JIS (English edition) are printed in Standardization and Quality Control, published
monthly by the Japanese Standards Association, and also provided to subscribers of JIS
(English edition) in Monthly Information.
Errata will be provided upon request, please contact:
Standards Publishing Department, Japanese Standards Association
4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN
TEL. 03-3583-8002 FAX. 03-3583-0462
PROTECTED BY COPYRIGHT