Professional Documents
Culture Documents
Description
Two-pack chromate free, fast drying, multi-substrate, high build, dark grey epoxy primer.
Can be used over abrasive blasted steel to provide optimal corrosion protection and adhesion to the subsequently
applied coatings. Provides excellent adhesion to steel and galvanized steel substrates.
Good moisture and chemical resistance.
Suitable Substrates
Existing finishes OEM Electro-coat Nax polyester bodyfillers & putties
Steel, Galvanized steel Glass reinforced laminates
Application
Flash-off
Dry to sand 20°C (70°F) 30°C (86°F) 40°C (100°F) 60°C (140°F)
7 - 8 hours 5 - 6 hours ±2 hours ±45 min.
Re – coatable with:
All Nax Superio preparatory products
All Nax Superio topcoats
Re-coating
Nippon Paint Automotive Refinishes recommends the use of fresh air supply respirator.
PPE For detailed information read the entire TDS
Global
Nax Superio Epoxy Primer
S.AR.03.002 /050616
Professional Use Only
Description
Two-pack chromate free, fast drying, multi-substrate, high build, dark grey epoxy primer.
Can be used over abrasive blasted steel to provide optimal corrosion protection and adhesion to the subsequently
applied coatings. Provides excellent adhesion to steel and galvanized steel substrates.
Good moisture and chemical resistance.
Suitable Substrates
Existing finishes OEM Electro-coat (ED) Nax polyester bodyfillers & putties
Steel, Galvanized Steel Glass reinforced laminates
Mixing
► Mixing Machine ► Product Mix
For best performance, stir primer on mixing Stir well, after each added component.
machine twice a day for 15 minutes
By volume Products
100 2 Nax Superior Epoxy Primer
50 1 Nax Superior Epoxy Primer Hardener
10 - 30 10 - 30% Nax Superio 400 Thinners
Notes:
Pot Life
Application 20°C(70°F) 30°C(86°F) 40°C(100°F)
► Spraying 4 - 5 hours 3 - 4 hours ±2 hours
Application
Application Number of coats
► By spraying Depending on desired film build 2 coats
► Apply one medium coat over the sanded repair area, then allow to flash for 5-10 minutes
► Apply a 2nd wet coat within the previous coat.
Notes: Allow each coat to flash-off naturally, do not force-dry by air support
Flash-off time depends on ambient temperature, applied layer thickness and airflow.
Recommended application criteria: 15-38 °C and 20-85% relative humidity
Drying time
20°C(70°F) 30°C(86°F) >40°C(100°F) 60°C(140°F)
► Dust dry ±20 min. ±15 min. ±10 min. -
► Dry to sand 7 - 8 hours 5 - 6 hours ±2 hours 45 min.
Notes: Allow a minimum of 10 minutes flash off at 20°C (70°F) before moving the car into a pre-heated 60°C (140°F) drying oven. All
drying times relate to standard application and object temperature. Consider the time required for the spraybooth to reach an
acceptable air temperature to enable the heat transfer of 60°C (140°F) to the object. Following the drying cycle at 60°C (140°F)
object temperature, allow product to completely cool down to ambient temperature.
Film thickness
Application
► Spraying Using the recommended application technique ±25 µm/coat
Re-coatable
► All Nax Superio preparatory products
► All Nax Superio topcoats
Coverage
By using the recommended application, the theoretical material coverage is:
► ± 07 m²/liter RTS mixture at ±45µm
► ± 80 ft²/liter RTS mixture at ±45µm
Notes: The practical material usage depends on many factors i.e. shape of the object, roughness of the surface, application
techniques, pressure and application circumstances.
Equipment cleaning
Solvent borne guncleaners
Solvent Content
► The VOC content of this product in ready to use form is max xxx g/liter
(lb/gallon)
Product storage
Minimum storage 5°C (41°F) Maximum storage 40°C (100°F)
temperature: temperature:
Notes: Product shelf-life is determined when products are stored unopened at 20°C (70°F).
Avoid extreme temperature fluctuation.