Professional Documents
Culture Documents
OUTLINE
The RP130x Series are CMOS-based positive voltage regulator ICs with high ripple rejection, low dropout
voltage, high output voltage accuracy and extremely low supply current. Each of these ICs consists of a voltage
reference unit, an error amplifier, a resistor-net for voltage setting, a short current limit circuit and a chip enable
circuit.
These ICs have an excellent low supply current performed by CMOS process, moreover they perform with low
dropout voltage due to built-in low ON-resistance. A chip enable function prolongs the battery life.
The input transient response, the load transient response and the ripple rejection have been improved in the
RP130x Series compared with the conventional products. Besides achieving low supply current (Typ.38μA).
The range of the operation voltage is capable from 1.7V to 6.5V and the range of the output voltage is capable
from 1.2V to 5.3V for this product, which is wider range as our conventional product R1114x series.
The output voltage of these ICs is fixed with high accuracy. Since the packages for these ICs are
DFN(PLP)1010-4, SOT-23-5 and SC-82AB, therefore high density mounting of the ICs on boards is possible.
FEATURES
• Supply Current ........................................................... Typ. 38μA
• Supply Current (Standby Mode) .................................. Typ. 0.1 μA
• Ripple Rejection........................................................... Typ. 80dB (f=1kHz)
• Input Voltage Range .................................................... 1.7V to 6.5V
• Output Voltage Range ................................................. 1.2V to 5.3V (0.1V steps)
(For other voltages, please refer to MARK INFORMATIONS.)
• Output Voltage Accuracy ............................................. ±1.0% (VOUT>2.0V, Topt=25°C)
• Temperature-Drift Coefficient of Output Voltage .......... Typ. ±20ppm/°C
• Dropout Voltage ........................................................... Typ. 0.32V (IOUT=150mA, VOUT=2.8V)
• Line Regulation............................................................ Typ. 0.02%/V
• Packages ..................................................................... DFN(PLP)1010-4, SC-82AB, SOT-23-5
• Built-in Fold Back Protection Circuit ............................ Typ. 40mA
• Ceramic capacitors are recommended to be used with this IC .....0.47μF or more
APPLICATIONS
• Power source for battery-powered equipment.
• Power source for portable communication equipment.
• Power source for electrical appliances such as cameras, VCRs and camcorders.
• Power source for high stable reference voltage.
1
RP130x
NO.EA-173-131031
BLOCK DIAGRAMS
RP130xxx1A
VDD VOUT
Vref
Current Limit
CE GND
RP130xxx1B RP130xxx1D
Vref Vref
CE GND CE GND
2
RP130x
NO.EA-173-131031
SELECTION GUIDE
The output voltage, chip enable polarity, auto discharge function, and package, etc. for the ICs can be selected
at the user’s request.
∗ : CE pin polarity and auto discharge function at off state are options as follows.
A: active low, without auto discharge function at off state.
B: active high, without auto discharge function at off state.
D: active high, with auto discharge function at off state.
3
RP130x
NO.EA-173-131031
PIN CONFIGURATIONS
1 2 2 1 1 2 1 2 3
PIN DESCRIPTIONS
• DFN(PLP)1010-4
Pin No Symbol Pin Description
1 VOUT Output Pin
2 GND Ground Pin
3 CE / CE Chip Enable Pin ("L" Active / "H" Active)
4 VDD Input Pin
∗) Tab is GND level. (They are connected to the reverse side of this IC.)
The tab is better to be connected to the GND, but leaving it open is also acceptable.
• SC-82AB
Pin No Symbol Pin Description
1 CE / CE Chip Enable Pin ("L" Active / "H" Active)
2 GND Ground Pin
3 VOUT Output Pin
4 VDD Input Pin
• SOT-23-5
Pin No Symbol Pin Description
1 VDD Input Pin
2 GND Ground Pin
3 CE / CE Chip Enable Pin ("L" Active / "H" Active)
4 NC No Connection
5 VOUT Output Pin
4
RP130x
NO.EA-173-131031
Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the
permanent damages and may degrade the life time and safety for both device and system using the device
in the field.
The functional operation at or over these absolute maximum ratings is not assured.
5
RP130x
NO.EA-173-131031
ELECTRICAL CHARACTERISTICS
VIN=VSET+1V (VOUT>1.5V), VIN=2.5V (VOUT ≤1.5V), IOUT=1mA, CIN=COUT=0.47µF, unless otherwise noted.
The specifications surrounded by are guaranteed by Design Engineering at - 40ºC ≤ Ta ≤ 85ºC.
• RP130xxx1A (Ta=25°C)
6
RP130x
NO.EA-173-131031
VIN=VSET+1V (VOUT>1.5V), VIN=2.5V (VOUT ≤1.5V), IOUT=1mA, CIN=COUT=0.47µF, unless otherwise noted.
The specifications surrounded by are guaranteed by Design Engineering at - 40ºC ≤ Ta ≤ 85ºC.
• RP130xxx1B/D (Ta=25°C)
7
RP130x
NO.EA-173-131031
Dropout Voltage
Output Voltage VDIF (V)
VOUT (V)
Condition TYP. MAX.
1.2V ≤ VSET < 1.5V 0.67 1.00
1.5V ≤ VSET < 1.7V 0.54 0.81
1.7V ≤ VSET < 2.0V 0.46 0.68
IOUT = 150mA
2.0V ≤ VSET < 2.5V 0.41 0.60
2.5V ≤ VSET < 4.0V 0.32 0.51
4.0V ≤ VSET 0.24 0.37
8
RP130x
NO.EA-173-131031
TYPICAL APPLICATION
RP130x
C1 C2
Series
CE GND
(External Components)
Ceramic Capacitor C2 0.47μF MURATA GRM155B30J474KE18B
TECHNICAL NOTES
When using these ICs, consider the following points:
Phase Compensation
In these ICs, phase compensation is made for securing stable operation even if the load current is varied. For
this purpose, use a capacitor C2 with 0.47μF or more.
If a tantalum capacitor is used, and its ESR (Equivalent Series Resistance) of C2 is large, the loop oscillation
may result. Because of this, select C2 carefully considering its frequency characteristics.
PCB Layout
Make VDD and GND lines sufficient. If their impedance is high, noise pickup or unstable operation may result.
Connect a capacitor C1 with a capacitance value as much as 0.47μF or more between VDD and GND pin, and as
close as possible to the pins.
Set external components, especially the output capacitor C2, as close as possible to the ICs, and make wiring as
short as possible.
9
RP130x
NO.EA-173-131031
PACKAGE INFORMATION
• Power Dissipation (DFN(PLP)1010-4)
Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the
measurement at the condition below:
Measurement Conditions
Standard Test Land Pattern
Environment Mounting on Board (Wind velocity=0m/s)
Board Material Glass cloth epoxy plastic (Double sided)
Board Dimensions 40mm x 40mm x 1.6mm
Copper Ratio Top side: Approx. 50%, Back side: Approx. 50%
Through-holes φ 0.54mm x 24pcs
600 40
500
PD (mW)
500
400 400
Power Dissipation
300
40
200
100
0
85
0 25 50 75 100 125 150
Ambience Temperature (°C) Measurement Board Pattern
IC Mount Area (Unit:mm)
Power Dissipation
The above graph shows the Power Dissipation of the package based on Tjmax=125°C and Tjmax=150°C.
Operating the IC in the shaded area in the graph might have an influence it's lifetime.
Operating time must be within the time limit described in the table below, in case of operating in the shaded area.
Estimated years
Operating Time
(Operating four hours/day)
13,000 hours 9years
10
RP130x
NO.EA-173-131031
0.07±0.05
0.25±0.05
0.48
1.00 0.65 ±0.05
B
A
3 4
X4 ※
0.05
45°
0.25±0.05
1.00
INDEX
3-C0.18 2 1 0.48
0.32±0.05
±0.05
0.6MAX.
0.05MIN.
0.25±0.05
0.05 M S AB
cd: Product Code … Please refer to RP130K Series Mark Specification Table
ef: Lot Number … Alphanumeric Serial Number
①②
③④
11
RP130x
NO.EA-173-131031
12
RP130x
NO.EA-173-131031
Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the
measurement at the condition below:
Measurement Conditions
Standard Land Pattern
Environment Mounting on Board (Wind velocity=0m/s)
Board Material Glass cloth epoxy plastic (Double Layers)
Board Dimensions 40mm x 40mm x 1.6mm
Copper Ratio Top side: Approx. 50%, Back side: Approx. 50%
Through-hole φ0.5mm x 44pcs
40
600
475 On Board
500
Power Dissipation PD (mW)
400
Free Air
380
300
40
200
100 150
0
85 Measurement Board Pattern
0 25 50 75 100 125 150
Ambient Temperature (ºC)
IC Mount Area (Unit : mm)
Power Dissipation
The above graph shows the Power Dissipation of the package based on Tjmax=125°C and Tjmax=150°C.
Operating the IC in the shaded area in the graph might have an influence it's lifetime.
Operating time must be within the time limit described in the table below, in case of operating in the shaded area.
Estimated years
Operating Time
(Operating four hours/day)
13,000 hours 9years
13
RP130x
NO.EA-173-131031
+0.05
2±0.2 1.0 -0.2
1.3±0.2
0.3±0.2
0.9±0.1
0.3±0.1 0.3±0.1 (0.7)
4 3
1.25 -0.1
+0.2
2.10±0.3
0 to 0.1
1 2
0.4±0.1 +0.1
0.3±0.1 0.16 -0.06
0.05
Unit : mm
cd: Product Code … Please refer to RP130Q Series Mark Specification Table
ef: Lot Number … Alphanumeric Serial Number
4 3
cd
ef
1 2
14
RP130x
NO.EA-173-131031
15
RP130x
NO.EA-173-131031
Measurement Conditions
Standard Test Land Pattern
Environment Mounting on Board (Wind velocity=0m/s)
Board Material Glass cloth epoxy plastic (Double sided)
Board Dimensions 40mm x 40mm x 1.6mm
Copper Ratio Top side: Approx. 50%, Back side: Approx. 50%
Through-holes φ 0.5mm x 44pcs
600
525
PD (mW)
500 On Board
400 420
Power Dissipation
Free Air
300 250
200
100
0
0 25 50 75 85 100 125 150
Ambience Temperature (°C)
The above graph shows the Power Dissipation of the package based on Tjmax=125°C and Tjmax=150°C.
Operating the IC in the shaded area in the graph might have an influence it's lifetime.
Operating time must be within the time limit described in the table below, in case of operating in the shaded area.
Estimated years
Operating Time
(Operating four hours/day)
9,000 hours 6years
16
RP130x
NO.EA-173-131031
2.9±0.2 1.1±0.1
1.9±0.2
0.8±0.1
(0.95) (0.95)
5 4
0~0.1
1.6-0.1
+0.2
2.8±0.3
0.2min.
1 2 3
+0.1
0.4±0.1 0.15-0.05
Unit : mm
cde: Product Code … Please refer to RP130N Series Mark Specification Table
fg: Lot Number … Alphanumeric Serial Number
5 4
cdefg
1 2 3
17
RP130x
NO.EA-173-131031
18
RP130x
NO.EA-173-131031
TEST CIRCUITS
VDD VOUT
RP130x
C1 C2 V VOUT IOUT
Series
CE GND
C1=Ceramic 0.47μF
C2=Ceramic 0.47μF
Basic Test Circuit
RP130x
A ISS C1 Series C2
CE GND
C1=Ceramic 0.47μF
C2=Ceramic 0.47μF
CE GND
C2=Ceramic 0.47μF
Ripple Rejection Test Circuit
RP130x
C1 C2
Series
CE GND
IOUTa IOUTb
C1=Ceramic 0.47μF
C2=Ceramic 0.47μF
Load Transient Response Test Circuit
19
RP130x
NO.EA-173-131031
TYPICAL CHARACTERISTICS
1) Output Voltage vs. Output Current (C1=0.47μF, C2=0.47μF, Topt=25°C)
RP130x121x RP130x281x
1.4 3.0
1.2
Output Voltage VOUT (V)
RP130x501x
6
Output Voltage VOUT (V)
2
VIN=6.0V
1 VIN=6.5V
0
0 100 200 300 400 500
Output Current IOUT (mA)
1.2
Output Voltage VOUT (V)
2.5
1.0
2.0
0.8
1.5
0.6
1.0
0.4 IOUT=1mA IOUT=1mA
IOUT=30mA IOUT=30mA
0.2 0.5
IOUT=50mA IOUT=50mA
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
Input Voltage VIN (V) Input Voltage VIN (V)
20
RP130x
NO.EA-173-131031
RP130x501x
6
Output Voltage VOUT (V)
2
IOUT=1mA
IOUT=30mA
1
IOUT=50mA
0
0 1 2 3 4 5 6
Input Voltage VIN (V)
40 40
30 30
20 20
10 10
0 0
0 1 2 3 4 5 6 0 1 2 3 4 5 6
Input Voltage VIN (V) Input Voltage VIN (V)
RP130x501x
50
Supply Current ISS (μA)
40
30
20
10
0
0 1 2 3 4 5 6
Input Voltage VIN (V)
21
RP130x
NO.EA-173-131031
RP130x501x
VIN=6.0V
5.05
5.04
Output Voltage VOUT (V)
5.03
5.02
5.01
5.00
4.99
4.98
4.97
4.96
4.95
-40 -25 0 25 50 75 85
Temperature Topt (°C)
38 38
36 36
34 34
32 32
30 30
-40 -25 0 25 50 75 85 -40 -25 0 25 50 75 85
Temperature Topt (°C) Temperature Topt (°C)
22
RP130x
NO.EA-173-131031
RP130x501x
VIN=6.0V
40
Supply Current ISS (μA)
38
36
34
32
30
-40 -25 0 25 50 75 85
Temperature Topt (°C)
25°C 25°C
0.6 - 40°C 0.30 - 40°C
0.5 0.25
0.4 0.20
0.3 0.15
0.2 0.10
0.1 0.05
0 0
0 25 50 75 100 125 150 0 25 50 75 100 125 150
Output Current IOUT (mA) Output Current IOUT (mA)
RP130x501x
0.30
85°C
Dropout Voltage VDIF (V)
0.25 25°C
- 40°C
0.20
0.15
0.10
0.05
0
0 25 50 75 100 125 150
Output Current IOUT (mA)
23
RP130x
NO.EA-173-131031
IOUT=50mA
0.5 IOUT=30mA
IOUT=10mA
0.4
0.3
0.2
0.1
0
1 2 3 4 5
Set Output Voltage VREG (V)
8) Ripple Rejection vs. Input Bias Voltage (C1=none, C2=0.47μF, Ripple=0.2Vp-p, Topt=25°C)
RP130x281x RP130x281x
IOUT=1mA IOUT=30mA
100 100
90 90
Ripple Rejection RR (dB)
80 80
70 70
60 60
50 50
40 40
30 f=100Hz 30 f=100Hz
20 f=1kHz 20 f=1kHz
f=10kHz f=10kHz
10 f=100kHz 10 f=100kHz
0 0
2.8 3.3 3.8 4.3 4.8 5.3 5.8 6.3 2.8 3.3 3.8 4.3 4.8 5.3 5.8 6.3
Input Voltage VIN (V) Input Voltage VIN (V)
80 80
70 70
60 60
50 50
40 40
30 IOUT=1mA 30 IOUT=1mA
20 IOUT=30mA 20 IOUT=30mA
10 IOUT=150mA 10 IOUT=150mA
0 0
0.1 1 10 100 1000 0.1 1 10 100 1000
Frequency f (kHz) Frequency f (kHz)
24
RP130x
NO.EA-173-131031
RP130x501x
VIN=6.0V
100
90
Ripple Rejection RR (dB)
80
70
60
50
40
30 IOUT=1mA
20 IOUT=30mA
10 IOUT=150mA
0
0.1 1 10 100 1000
Frequency f (kHz)
3 5
Output Voltage VOUT (V)
1 3
1.205 2.805
1.200 2.800
Output Voltage Output Voltage
1.195 2.795
1.190 2.790
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
Time t (μs) Time t (μs)
RP130x501x
7
6
Output Voltage VOUT (V)
Input Voltage
Input Voltage VIN (V)
5.005
5.000
Output Voltage
4.995
4.990
0 10 20 30 40 50 60 70 80 90 100
Time t (μs)
25
RP130x
NO.EA-173-131031
1.21 2.81
1.20 2.80
1.18 2.78
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
Time t (μs) Time t (μs)
RP130x501x
150
Output Current IOUT (mA)
100
Output Voltage VOUT (V)
Output Current
50
50mA 100mA
5.01 0
5.00
4.99
4.97
0 10 20 30 40 50 60 70 80 90 100
Time t (μs)
Output Current
1mA 150mA 1mA 150mA 0
0
2.90
1.30
2.85
1.25
2.80
1.20
2.75
Output Voltage
1.15 Output Voltage 2.70
1.10 2.65
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
Time t (μs) Time t (μs)
26
RP130x
NO.EA-173-131031
RP130x501x
200
Output Current
1mA 150mA 0
5.05
5.00
4.95
Output Voltage
4.90
4.85
0 10 20 30 40 50 60 70 80 90 100
Time t (μs)
0 0
1.5 1.5
1.0 1.0
Output Voltage Output Voltage
0.5 0.5
0 0
0 4 8 12 16 20 24 28 32 36 0 4 8 12 16 20 24 28 32 36
Time t (μs) Time t (μs)
RP130x121x RP130x281x
IOUT=150mA IOUT=1mA
3 6
CE Input Voltage VCE (V)
2 4
Output Voltage VOUT (V)
0 0
1.5 3
1.0 2
Output Voltage Output Voltage
0.5 1
0 0
0 4 8 12 16 20 24 28 32 36 0 4 8 12 16 20 24 28 32 36
Time t (μs) Time t (μs)
27
RP130x
NO.EA-173-131031
RP130x281x RP130x281x
IOUT=30mA IOUT=150mA
6 6
0 0
3 3
2 2
Output Voltage Output Voltage
1 1
0 0
0 4 8 12 16 20 24 28 32 36 0 4 8 12 16 20 24 28 32 36
Time t (μs) Time t (μs)
RP130x501x RP130x501x
IOUT=1mA IOUT=30mA
9 9
CE Input Voltage VCE (V)
0 0
6 6
4 4
Output Voltage Output Voltage
2 2
0 0
0 10 20 30 40 50 60 70 80 90 0 10 20 30 40 50 60 70 80 90
Time t (μs) Time t (μs)
RP130x501x
IOUT=150mA
9
CE Input Voltage VCE (V)
6
Output Voltage VOUT (V)
CE Input Voltage 3
4
Output Voltage
2
0
0 10 20 30 40 50 60 70 80 90
Time t (μs)
28
RP130x
NO.EA-173-131031
14) Turn Off Speed with CE pin (D Version) (C1=0.47μF, C2=0.47μF, Topt=25°C)
RP130x121D RP130x121D
IOUT=1mA IOUT=30mA
3 3
0 0
1.5 1.5
1.0 1.0
0 0
0 20 40 60 80 100 120 140 160 180 0 20 40 60 80 100 120 140 160 180
Time t (μs) Time t (μs)
RP130x121D RP130x281D
IOUT=150mA IOUT=1mA
3 6
CE Input Voltage VCE (V)
0 0
1.5 3
1.0 2
Output Voltage
0.5 Output Voltage 1
0 0
0 20 40 60 80 100 120 140 160 180 0 10 20 30 40 50 60 70 80 90
Time t (μs) Time t (μs)
RP130x281D RP130x281D
IOUT=30mA IOUT=150mA
6 6
CE Input Voltage VCE (V)
4 4
Output Voltage VOUT (V)
0 0
3 3
2 2
Output Voltage Output Voltage
1 1
0 0
0 10 20 30 40 50 60 70 80 90 0 10 20 30 40 50 60 70 80 90
Time t (μs) Time t (μs)
29
RP130x
NO.EA-173-131031
RP130x501D RP130x501D
IOUT=1mA IOUT=30mA
9 9
0 0
6 6
4 4
Output Voltage Output Voltage
2 2
0 0
0 10 20 30 40 50 60 70 80 90 0 10 20 30 40 50 60 70 80 90
Time t (μs) Time t (μs)
RP130x501D
IOUT=150mA
9
CE Input Voltage VCE (V)
6
Output Voltage VOUT (V)
CE Input Voltage 3
4
Output Voltage
2
0
0 10 20 30 40 50 60 70 80 90
Time t (μs)
2.2
2.0
1.8
Input Voltage VIN (V)
1.6
1.4 Hatched area is available
1.2 for 1.2V output.
1.0
0.8
0.6
0.4
0.2
0
0 25 50 75 100 125 150
Output Current IOUT (mA)
30
RP130x
NO.EA-173-131031
The relations between IOUT (Output Current) and ESR of an output capacitor are shown below.
The conditions when the white noise level is under 40μV (Avg.) are marked as the hatched area in the graph.
Measurement conditions
Frequency Band : 10Hz to 3MHz
Temperature : −40°C to 85°C
C1, C2 : 0.47μF
RP130x121x RP130x281x
VIN=1.4V to 6.5V VIN=3.0V to 6.5V
100 100
Topt=85°C Topt=85°C
10 Topt=-40°C 10 Topt=-40°C
ESR (Ω)
ESR (Ω)
1 1
0.1 0.1
0.01 0.01
0 25 50 75 100 125 150 0 25 50 75 100 125 150
Output Current IOUT (mA) Output Current IOUT (mA)
RP130x501x
VIN=5.2V to 6.5V
100
Topt=85°C
10 Topt=-40°C
ESR (Ω)
0.1
0.01
0 25 50 75 100 125 150
Output Current IOUT (mA)
31
1. The products and the product specifications described in this document are subject to change or
discontinuation of production without notice for reasons such as improvement. Therefore, before
deciding to use the products, please refer to Ricoh sales representatives for the latest information
thereon.
2. The materials in this document may not be copied or otherwise reproduced in whole or in part without
prior written consent of Ricoh.
3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or
otherwise taking out of your country the products or the technical information described herein.
4. The technical information described in this document shows typical characteristics of and example
application circuits for the products. The release of such information is not to be construed as a
warranty of or a grant of license under Ricoh's or any third party's intellectual property rights or any
other rights.
5. The products listed in this document are intended and designed for use as general electronic
components in standard applications (office equipment, telecommunication equipment, measuring
instruments, consumer electronic products, amusement equipment etc.). Those customers intending to
use a product in an application requiring extreme quality and reliability, for example, in a highly specific
application where the failure or misoperation of the product could result in human injury or death
(aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and
transportation equipment, combustion equipment, safety devices, life support system etc.) should first
contact us.
6. We are making our continuous effort to improve the quality and reliability of our products, but
semiconductor products are likely to fail with certain probability. In order to prevent any injury to
persons or damages to property resulting from such failure, customers should be careful enough to
incorporate safety measures in their design, such as redundancy feature, fire containment feature and
fail-safe feature. We do not assume any liability or responsibility for any loss or damage arising from
misuse or inappropriate use of the products.
7. Anti-radiation design is not implemented in the products described in this document.
8. Please contact Ricoh sales representatives should you have any questions or comments concerning
the products or the technical information.
http://www.e-devices.ricoh.co.jp/en/