Professional Documents
Culture Documents
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 1 of 40
1001202808
MONOFLANGE VALVE, SS316, CL150, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 2 of 40
1001202809
MONOFLANGE VALVE, SS316, CL300-600, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 3 of 40
1001202810
MONOFLANGE VALVE, SS316, CL150-600, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 4 of 40
1001202781
MONOFLANGE VALVE, SS316, CL900-1500, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 5 of 40
1001202782
MONOFLANGE VALVE, SS316, CL150, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 6 of 40
1001202813
MONOFLANGE VALVE, SS316, CL300-600, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
1001202814
Page 7 of 40
MONOFLANGE VALVE, SS316, CL900-1500, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
1001202815
MONOFLANGE VALVE, DSS, CL150-600, SBB, DN15X15
Page 8 of 40
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 9 of 40
1001202816
MONOFLANGE VALVE, DSS, CL150, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 10 of 40
1001202817
MONOFLANGE VALVE, DSS, CL300-600, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 11 of 40
1001202818
MONOFLANGE VALVE, DSS, CL150-600, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 12 of 40
1001202819
MONOFLANGE VALVE, DSS, CL900-1500, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 13 of 40
1001202820
MONOFLANGE VALVE, DSS, CL150, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 14 of 40
1001202822
MONOFLANGE VALVE, DSS, CL300-600, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 15 of 40
1001202823
MONOFLANGE VALVE, DSS, CL900-1500, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 16 of 40
1001202824
MONOFLANGE VALVE, SDSS, CL150-600, SBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 17 of 40
1001202825
MONOFLANGE VALVE, SDSS, CL150, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 18 of 40
1001202826
MONOFLANGE VALVE, SDSS, CL300-600, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 19 of 40
1001202827
MONOFLANGE VALVE, SDSS, CL150-600, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 20 of 40
1001202828
MONOFLANGE VALVE, SDSS, CL900-1500, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 21 of 40
1001202829
MONOFLANGE VALVE, SDSS, CL150, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 22 of 40
1001202830
MONOFLANGE VALVE, SDSS, CL300-600, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 23 of 40
1001202831
MONOFLANGE VALVE, SDSS, CL900-1500, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 24 of 40
1001202832
MONOFLANGE VALVE, ALLOY 625, CL150-600, SBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 25 of 40
1001202833
MONOFLANGE VALVE, ALLOY 625, CL150, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 26 of 40
1001202834
MONOFLANGE VALVE, ALLOY 625, CL300-600, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 27 of 40
1001202835
MONOFLANGE VALVE, ALLOY 625, CL150-600, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 28 of 40
1001202836
MONOFLANGE VALVE, ALLOY 625, CL900-1500, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 29 of 40
1001202837
MONOFLANGE VALVE, ALLOY 625, CL150, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 30 of 40
1001202838
MONOFLANGE VALVE, ALLOY 625, CL300-600, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 31 of 40
1001202839
MONOFLANGE VALVE, ALLOY 625, CL900-1500, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 32 of 40
1001202840
MONOFLANGE VALVE, ALLOY 825, CL150-600, SBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 33 of 40
1001202841
MONOFLANGE VALVE, ALLOY 825, CL150, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 34 of 40
1001202842
MONOFLANGE VALVE, ALLOY 825, CL300-600, SBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 35 of 40
1001202843
MONOFLANGE VALVE, ALLOY 825, CL150-600, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 36 of 40
1001202844
MONOFLANGE VALVE, ALLOY 825, CL900-1500, DBB, DN15X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 37 of 40
1001202845
MONOFLANGE VALVE, ALLOY 825, CL150, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 38 of 40
1001202846
MONOFLANGE VALVE, ALLOY 825, CL300-600, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 39 of 40
1001202847
MONOFLANGE VALVE, ALLOY 825, CL900-1500, DBB, DN50X15
Valves
Notes:
1. Pressure / temperature rating shall confirm to ASME B16.34
2. Hardness value to comply with ISO-15156 on all wetted
parts
3. Valves shall have anti-blow out stems (Pinned locked
bonnet, where applicable, to prevent inadvertent
disengagement)
4. All o-rings and seals to be resistant to explosive
decompression
5. Weld repairs are not allowed
6. Valve to be supplied with permanently attached
stainless steel tag plate stamped with requisition/item
number and tag number
7. Valve to be supplied with a locking device to allow the
valve to be locked in open or closed position
8. Threaded end: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape
9. Bleed outlet: To be fitted with swagelok compression
fitting to 3/8 in outer diameter tubing, properly fitted with
PTFE sealant tape. Bleed valve shall be fitted with 5 mm
square anti-tamper facility
10. The swagelok compression fitting mentioned above shall be
supplied by vendor
11. Hexagonal headed plug for bleed outlet of 1/4 in size
shall also be supplied by vendor
Page 40 of 40