Professional Documents
Culture Documents
GOVERNMENT OF INDIA
CENTRAL FARM MACHINERY TRAINING & TESTING INSTITUTE
TRACTOR NAGAR, BUDNI (MADHYA PRADESH) 466445, INDIA
Email: fmti-mp@nic.in
Web site: cfmtti-dacnet.nic.in
i) The results reported in this report are observed values and no corrections have
been applied for atmospheric and site conditions.
ii) The data given in this report pertain to the particular machine submitted by the
applicant for test.
iii) The results presented in this report do not in any way attribute to the durability of
the machine.
iv) This report should not be reproduced in part or full without prior permission of
the Director, Central Farm Machinery Training and Testing Institute, Budni
(M.P.).
v) This is a Variant test report and, should be read in conjunction with the Test
Report of base model i.e. “Kubota MU5501 Tractor” bearing No. T-
978/1502/2015, August, 2015.
Sl.
Units Conversion Factor
No
1 Force: As per applicant apa
1 kgf 9.80665 N Top Dead Centre TDC
2.20462 lbf Indian Standard IS
2 Power: Left Hand Side/ LHS/RHS
Right Hand Side
1 hp 1.01387metric hp (Ps) Mercury Hg.
745.7 W Temperature Temp.
1 Ps 735.5 W Not recorded N.R.
1 kW 1.35962 Ps Revolutions per minute rpm
3 Pressure: Outer diameter/ O.D/I.D
Inner diameter
1 psi 6.895 kPa Not available/ N.A.
Not applicable
2
1 kgf/cm 98.067 kPa = 735.56 Power take-off PTO
mm of Hg
2
1 bar 100 kPa = 10 N/cm Relative Humidity R.H.
1 mm of Hg 1.3332 m-bar
1 2 3 4 5 6
h) Front wheel: Various configuration in base & variant Changed
models (refer para 3.18.1).
i) Differential
Reduction through crown NA 2.3:1 (23/10T)
Changed
wheel and bevel pinion
j) Front final drive
Type NA Crown wheel & bevel
Changed
pinion
Reduction through final drive NA 5.1:1 (51/10T) Changed
k) Sheet metal:
Style of bonnet & Fender
- Colour Orange Orange No change
-Decals (Sticker) KUBOTA KUBOTA MU5501
Changed
MU5501 4WD
l) Unballasted mass of tractor, 2215 2440
Changed
(kg)
On the basis of test conducted the performance results have been summarized as
evaluative (mandatory) and non – evaluative (not mandatory) parameters applicable for
qualifying Minimum Performance Criteria as per clause-4 table-1 of Indian Standard
12207: 2014 for acceptance of tractor for the purpose of subsidies/NABARD financing for
the applicable features for this tractor model.
6.1 Evaluative & Non Evaluative Parameters:
Values Whether
declared by As observed Variant
Category model
Sl. (Evaluative /
Requirements the meets
Characteristic as per IS: applicant/ the
No. Non 12207-2014
Evaluative) requirement require-
Base Variant Base Variant ments
model Model model model (Yes/No)
1 2 3 4 5a 5b 6a 6b 7
5.1.1 PTO Performance :
a) - Max. power Declared value
under 2 h test, Evaluative to be achieved
(kW ) with a
tolerance of: -5
(Natural ambient
/ +10% for PTO
condition) power >26 kW.
–7.5/+10% for
PTO power 35 35 34.5 36.4 Yes
26 kW or-5 /
+10% for
engine power
>26 kW. –
7.5/+10% for
engine power
26 kW
b) Specific fuel
consumption Non 5%
corresponding to Evaluative 249 249 247 243 Yes
maximum power,
(g/kWh)
1 2 3 4 5a 5b 6a 6b 7
6.1.2 Drawbar performance :
a) Maximum drawbar 20.08 21.45
pull with ballast Non Minimum 65% (R) (R)
corresponding to 15 Evaluative of static mass Minimum Minimum
22.86 31.42 Yes
percent wheel slip, with ballast 24.6(D) 30.2(D)
(kN)
6.5.2 The literature should also be brought out as per IS: 8132-1999 (Reaffirmed in March,
2009) for the guidance of users and service personnel in national as well as regional
languages for this model of tractor.
ANNEXURE-I
ANNEXURE-II