Professional Documents
Culture Documents
ICS 93.030
English version
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15229:2005: E
worldwide for CEN national Members.
prEN 15229:2005 (E)
Contents Page
Foreword................................................................................................................................................ 3
1 Scope.............................................................................................................................................. 4
2 Normative references ................................................................................................................... 4
3 Terms and definitions................................................................................................................... 5
4 Performance requirements .......................................................................................................... 6
4.1 Loading ........................................................................................................................................ 6
4.1.1 Maximum load for admissible deformation ................................................................................ 6
4.1.2 Mechanical stability of risers ...................................................................................................... 6
4.1.3 Mechanical stability of base components .................................................................................. 6
4.2 Dimensions .................................................................................................................................. 6
4.2.1 Internal dimensions .................................................................................................................... 6
4.2.2 Dimensional tolerances relating to jointing surfaces.................................................................. 6
4.3 Leaktightness ............................................................................................................................... 7
4.3.1 General ...................................................................................................................................... 7
4.3.2 Chamber components................................................................................................................ 7
4.3.3 Pipe connections........................................................................................................................ 7
4.3.4 Leaktightness of joints made by using adhesive bonding or fusion techniques ........................ 7
4.4 Durability ...................................................................................................................................... 7
4.4.1 Durability of manhole and inspection chamber bases ............................................................... 7
4.4.2 Durability of thermoplastics risers and thermoplastics near surface components..................... 7
4.4.3 Durability of elastomeric sealing joints....................................................................................... 8
4.5 Release of dangerous substances .............................................................................................. 8
5 Test methods................................................................................................................................. 8
5.1 Loading ........................................................................................................................................ 8
5.1.1 Surface and traffic loading ......................................................................................................... 8
5.1.2 Stiffness of riser shaft................................................................................................................. 8
5.1.3 Mechanical stability and durability of base components............................................................ 8
5.2 Dimensions and dimensional tolerances ..................................................................................... 8
5.3 Tightness...................................................................................................................................... 8
5.3.1 Riser joints ................................................................................................................................. 8
5.3.2 Joints to pipework ...................................................................................................................... 8
6 Evaluation of conformity .............................................................................................................. 8
6.1 General ........................................................................................................................................ 8
6.2 Initial type testing ......................................................................................................................... 9
6.3 Factory production control by the manufacturer ........................................................................ 10
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directives..................................................................................................... 11
ZA.1 Scope and relevant characteristics ............................................................................................ 11
ZA.2 Procedure for the attestation of conformity of manholes and inspection chambers.................. 12
ZA.3 CE marking and labelling ........................................................................................................... 14
Bibliography ........................................................................................................................................ 16
2
prEN 15229:2005 (E)
Foreword
This document (prEN 15229:2005) has been prepared by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting system”, the secretariat of which is held by NEN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This document includes the following:
— Annex ZA, which is informative, details the aspects of performance to be examined in order to satisfy the
Essential Requirements of the Construction Products Directive 89/106/EEC and amplified by the
appropriate Interpretative Document. Although informative, compliance with the annex is compulsory for
products sold within the EEA;
— Bibliography.
3
prEN 15229:2005 (E)
1 Scope
This document specifies performance requirements for thermoplastics manholes and inspection chambers
and their joints intended to be used for non-pressure underground drainage and sewerage applications and
gives associated test methods for verification and evaluation of conformity with this document. This document
includes separate tests for the near surface components, the riser shaft and the base unit, all of which can be
supplied either individually or as a kit for site assembly. It does not include the testing requirements for the
cover and frame. It includes suggested classification levels but allows the manufacturer to declare his
individual test results.
Products conforming to this document may be used internally within a building or externally and may also be
used in renovation and replacement.
This document also applies to manholes and inspection chambers used in highway, railway or other surface
water drainage systems but covers only those characteristics subject to regulatory requirements.
This document neither includes catch pots and gullies nor does it include covers or frames these being
specified in EN 124 [1].
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 476:1997, General requirements for components used in discharge pipes, drains and sewers for gravity
systems
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 3: Cellular materials of vulcanised rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 763:1994, Plastics piping and ducting systems — Injection moulded thermoplastics fittings — Test
method for visually assessing the effects of heating
EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized
poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene
(PP) — Part 1: Specifications for pipes, fittings and the system
prEN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
prEN 13476-1, Thermoplastics plastics piping systems for non-pressure underground drainage and sewerage
— Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
4
prEN 15229:2005 (E)
EN 13598-1:2003, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: Specifications
for ancillary fittings including shallow inspection chambers
prEN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene with mineral modifiers (PP-M) — Part 1: Specifications for pipes, fittings and the system
prEN 14802, Plastics piping systems — Plastics shafts or risers for inspection chambers and manholes —
Determination of resistance against surface and traffic loading
prEN 14830, Thermoplastics inspection chambers and manhole bases — Test methods for buckling
resistance
prEN 14982, Thermoplastics piping systems — Plastics shafts or risers for inspection chambers and
manholes — Determination of ring stiffness
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
(ISO 3126:2005)
3.5
manhole
drainage or sewerage fitting used to connect drainage or sewerage installations and/or to change the direction
of drainage or sewerage runs, which terminates at ground level and has a riser shaft with a minimum inner
diameter of 800 mm (see also EN 476:1997 for non circular manholes)
5
prEN 15229:2005 (E)
NOTE The termination at ground level permits the introduction of cleaning, inspection and test equipment and the
removal of debris and provides access for personnel.
4 Performance requirements
4.1 Loading
4.2 Dimensions
6
prEN 15229:2005 (E)
c) stating the values of his own specification and associated jointing method.
Dimensions shall be measured in accordance with 5.2 and shall be within the declared tolerances.
4.3 Leaktightness
4.3.1 General
In order to enable the declaration of leaktightness of both the riser assembly and the elastomeric sealing ring
joints, the requirements of 4.3.2 and 4.3.3 shall apply.
For systems with a joint design not intended to meet the tightness requirements of 4.3.2 and/or 4.3.3, the
declaration “Non-watertight joints” shall be used.
4.4 Durability
7
prEN 15229:2005 (E)
5 Test methods
5.1 Loading
5.3 Tightness
6 Evaluation of conformity
6.1 General
The conformity of the products to the requirements of this document and to the stated values (including
classes) shall be demonstrated by:
— initial type testing;
— factory production control by the manufacturer, including product assessment.
8
prEN 15229:2005 (E)
For the purposes of ITT products may be grouped into families per characteristic where it is considered that
the test results for that characteristic from any one product within the family is representative of all other
products within the family.
Material modifications within certain limits are not considered a change of material. Guidance for these limits
can be found in ENV 1401-2 [2] for PVC-U, ENV 1852-2 [3] for PP, prCEN/TS 12666-2 [4] for PE and
prCEN/TS 13476-2 [5] for structured wall components of PVC-U, PP and PE.
For tests previously performed in accordance with the provisions of EN 1401-1, EN 1852-1, prEN 12666-1,
prEN 13476-1, EN 13598-1, or prEN 14758-1 where they relate to the characteristics of this document and
where carried out on products of the same design, the results may be taken into account.
Where sealing rings have already been shown to comply with EN 681-1, EN 681-2, EN 681-3 or EN 681-4, no
further testing is required to demonstrate conformity with the requirements of this document.
Test reports shall be kept by the manufacturer for at least 10 years after the date of last production of the
product to which they apply.
9
prEN 15229:2005 (E)
Table 3 — Characteristics of chambers and manholes and minimum sampling frequencies for FPC
10
prEN 15229:2005 (E)
Annex ZA
(informative)
This annex has the same scope as Clause 1 of this standard with regard to the products covered. It
establishes the conditions for the CE marking of manholes and inspection chambers for use as indicated and
shows the relevant clauses applicable (see Table ZA.1).
Intended use: Access to buried drain or sewer systems intended for conveyance under gravity
or occasionally at low head of pressure and installed in areas subjected to
pedestrian and/or vehicular traffic.
11
prEN 15229:2005 (E)
The requirement on a certain characteristic is not applicable in those Member States where there are no
regulatory requirements on that characteristic for the intended end use of the product. In this case,
manufacturers placing their products on the market of these Member States are not obliged to determine nor
declare the performance of their products with regard to this characteristic and the option “No performance
determined” (NPD) in the information accompanying the CE marking (see ZA.3) may be used. The NPD
option may not be used, however, where the characteristic is subject to a threshold level.
12
prEN 15229:2005 (E)
Attestation of
Product Intended use Level or class conformity
system
Access to buried drain or sewer systems intended
Manholes and
for conveyance under gravity or occasionally at
inspection None 4a
low head of pressure and installed in areas
chambers
subjected to pedestrian and/or vehicular traffic.
a
System 4: See Directive 89/106/EEC (CPD) Annex III.2.(ii), third possibility.
The attestation of conformity of manholes and inspection chambers indicated in Table ZA.1 shall be based on
the evaluation of conformity procedures indicated in Table ZA.3 resulting from application of the clauses of
this standard indicated therein.
Table ZA.3 — Assignment of evaluation of conformity tasks for manholes and inspection chambers
Evaluation of conformity
Tasks Content of task
clauses to apply
Factory production Parameters related to all relevant
6.3
Tasks for the control (F.P.C.) characteristics of Table ZA.1
manufacturer All relevant characteristics of
Initial type testing 6.2
Table ZA.1
— provisions to which the product conforms (i.e. Annex ZA of this EN), and a reference to the ITT report(s)
and factory production control reports (if appropriate);
— particular conditions applicable to the use of the product e.g. maximum recommended depth in ground
and the maximum recommended level of ground water;
— name of, and position held by, the person empowered to sign the declaration on behalf of the
manufacturer or his authorised representative.
The above mentioned declaration shall be presented in the official language or languages accepted in the
Member State in which the product is to be used.
13
prEN 15229:2005 (E)
14
prEN 15229:2005 (E)
AnyCo Ltd, P.O. Box 21, B-1050 Name or identifying mark and
registered address of the producer
06 Last two digits of the year in which the
marking was affixed
EN 15229 Number of this European Standard
In addition to any specific information relating to dangerous substances shown above, the product should also
be accompanied, when and where required and in the appropriate form, by documentation listing and any
other legislation on dangerous substances for which compliance is claimed, together with any information
required by that legislation.
NOTE European legislation without national derogations need not be mentioned.
15
prEN 15229:2005 (E)
Bibliography
[1] EN 124, Gully tops and manhole tops for vehicular and pedestrian areas — Design requirements —
Type testing, marking
[2] ENV 1401-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U) — Part 2: Guidance for assessment of conformity
[3] ENV 1852-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene (PP) — Part 2: Guidance for the assessment of conformity
[4] prCEN/TS 12666-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Polyethylene (PE) — Part 2: Guidance for the assessment of conformity
[5] prCEN/TS 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE) — Part 2: Assessment of conformity
[6] EN ISO 9001:2000, Quality management systems — Requirements (ISO 9001:2000)
16