Professional Documents
Culture Documents
Design Truss Tower R2 PDF
Design Truss Tower R2 PDF
PERFORMED FOR;
DOCUMENT TITLE:
www.alpineburj.comcommerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
Reference Drawings
© Copyright
This document is the property of alpine burj and may contain confidential and proprietary information. It may not be used for
any purpose other than that for which it is supplied. This document may not be wholly or partly disclosed, copied, duplicated or
in any way made use of without prior written approval of Alpine Burj Consultancy.
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
TABLE OF CONTENTS
1.0 INTRODUCTION 5
2.0 REFERENCES 6
2.1 Codes and Standards 6
2.2 Drawings 6
2.3 Materials 6
3.0 EXECUTIVE SUMMARY 7
4.0 Modeling 7
4.1 Structural Modeling 7
4.2Boundary Conditions 8
4.3 Loading 8
4.3.1 Dead Load (Load Case-1) 8
4.3.2 Other Dead Loads (Load Case-2) 8
4.3.3 Live Load (Load Case-3) 8
4.3.4 Wind Load (Load Case-4) 8
4.4 Load Combinations 8
5 Design and Conclusion 9
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
1.0 INTRODUCTION
The Scope of this document is the structural analysis and design of roof truss for Customs
building. The building L shaped with dimension 47.90m x 27.60m as dimension of the roof.
The roof structure has two parts, one part is with mono slope truss spanning 10.60m end to
end. The other part is having duo pitch roof truss spanning 17.10m. The entire roof
structure is modelled in STAAD PRO software in order to verify its stability and design
strength of the structural framing for loading conditions encountered such as Dead load,
Live load and Wind load. The load calculations are done using BS 6399- Part 1,2 and 3. The
detailed load calculations are attached in Annexure A.
The STAAD models is generated and design check is performed for all members using BS
5950-2000 edition. The steel structure connection is designed as a combination of welded
and bolted connection. All truss members are directly welded and truss is connected to
concrete beam using anchor bolts. The following load combinations are generated in STAAD
for check.
Structural framing is checked for worst case combination of all above load conditions and all
members are found satisfactory.
1.1 CONFIGURATION OF Steel structure- ROOF TRUSS
Length = 47.90m
Width = 27.60m
10.60 Truss
Part 2
Truss
Part 1
17.10
Figure 1: ROOF STRUCTURE - GEOMETRY
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
2.0 REFERENCES
2.2 Drawings
Please refer Custom Building drawing showing the structural arrangement of roof truss.
2.3 Materials
All RHS and SHS structural steel members are considered as S275 JR grade
All bolts and anchor bolts are considered as Gr 8.8 grade.
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
4.0 Modeling
1.26m
0.41m
17.00m
Y
Z X
Load 1
Figure 3: TRUSS TYPE 1
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
1.45m
0.41m
10.50m
Y
Z X
Load 1
4.2Boundary Conditions
Truss is considered as pinned at both ends.
4.3 Loading
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 30-11-2016
www.alpineburj.com commerce@alpineburj.com
Project No: ABCC078-16-XXX-XX-XXXX Date: 26-11-2016
APPENDIX: A
1. Loading Calculations
2. STAAD Inputs
3. Loads Applied
4. Member Forces and Utilisation Ratio
5. Design of Connections
www.alpineburj.com commerce@alpineburj.com
Project : Rev 01
Date : 11/24/16
Design of Truss Tower Job No:
Date : 11/24/16
LOADING CALCULATIONS RT1
4.2
LT1 LT2 LT3 LT4 LT5 LT6
LT-7 RT-2
PART 2 6.2
RT-4
PART 1 5.1
4.8 RT-5
LOADING CALCULATIONS
1 DEAD LOAD :
Total DL 17 kg/m
Say 20 kg/m
0.2 kN/m2
(non accessible roofs)
2 LIVE LOAD : As per clause 6.2 of BS 6399 - Part 1 0.75 kN/m2
A E
7
Zone Pressure (kN/m2)
Wind along Short AREA A -6.71
dir'n 27.6 AREA B -4.63
C AREA C -2.56
B F G 27600 AREA E -2.52
13.6 AREA F -1.82
X -Axis 1.4 AREA G -1.68
1.4
A E
7
C 10.6
A B A
5.3 5.3
Pressure
Zone Cpe Cpi (Cpe-Cpi) kN/m2 bL/10 bL/2
A -1.75 -0.3 -2.05 -6.56 1.06 5.3
B -1.16 -0.3 -1.46 -4.672 1.06 5.3
C -0.57 -0.3 -0.87 -2.784 9.54 0
Project : Rev 01
Date : 11/24/16
Design of Truss Tower Job No:
Date : 11/24/16
Summary ofLOADING
PressureCALCULATIONS
applied - WIND on Truss 1
UDL (kN/m)
Truss ZONE A ZONE B ZONE C ZONE E ZONE F ZONE G
RT-1 -14.091 -5.376 -5.292 -3.528
RT-2 -34.892 -13.312 -13.104 -8.736
RT-3 -30.558 -16.896 -12.012 -11.088
RT-4 -28.012 -15.488 -11.011 -10.164
RT-5 -33.21 -12.672 -12.474 -8.316
RT-6 -13.42 -5.12 -5.04 -3.36
IV غ
II
III
Wind Direction
I II III IV
Wind direction غ 180 270 360 90
Direction factor Sd 0.965 1.000 0.865 0.765
Site Wind Speed (m/s) Vs 22.50 23.32 20.17 17.84 equ (8)
Job Information
Engineer Checked Approved
Name: PPH
Date: 24-Nov-16
1 DEAD LOAD
2 IMPOSED LOAD
3 LIVE LOAD
4 WIND LOAD TRUSS
Job No Sheet No Rev
2
Part
Software licensed to
Job Title Custom Buildings Ref
3D Rendered View
Job No Sheet No Rev
3
Part
Software licensed to
Job Title Custom Buildings Ref
1.26m
0.41m
17.00m
Y
Z X
Load 1
Truss Type 1
Y
Z X
Load 1
TUB2002006.3
TUB2002006.3
TUB2002006.3
TUB2002006.3
TUB1001006.0
TUB2002006.3
TUB2002006.3
TUB1001006.0
TUB1001006.0
TUB1001006.0
TUB1001006.0
TU 0
TUB2002006.3 6. TUB2002006.3
TUB1001006.0
TUB1001006.0
TU B1
100 06.0
TUB1001006.0
TUB1001006.0
TUB B10 00 TUB2002006.3
TUB2002006.3 10 00 010 6.0
TUB160805.0
TUB160805.0
010 06. B1
TUB 100 06.0 B10 100 006.0
TUB12 1001 100
6.0
0 TU TU 100 1001 0
01208. 006.0 TUB TUB 01208.
0 TUB12
TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0 TUB1201208.0
Y
Truss Type 1- Section sizes
Y
Truss Type 1* Loads 0.7kN:1m 2 IMPOSED LOAD
Job No Sheet No Rev
5
Part
Software licensed to
Job Title Custom Buildings Ref
Y
Z X
Load 3
-14.090 kN/m
-5.370 kN/m -5.300 kN/m
-5.370 kN/m -5.300 kN/m
-5.370 kN/m -5.300 kN/m
-5.370 kN/m -5.300 kN/m
-3.528 kN/m
Y
Z X
Load 4
1.45m
0.41m
10.50m
Y
Z X
Load 1
Truss Type 2
-1.150 kN/m
-1.150 kN/m
-1.150 kN/m
-1.150 kN/m
-1.150 kN/m
-1.150 kN/m
-1.150 kN/m
Y
Z X
Load 2
-4.290 kN/m
-4.290 kN/m
-4.290 kN/m
-4.290 kN/m
-4.290 kN/m
-4.290 kN/m
-4.290 kN/m
Y
Z X
Load 3
-26.750 kN/m
-15.940 kN/m
-15.940 kN/m
-15.940 kN/m
-15.940 kN/m
-15.940 kN/m
-15.940 kN/m
Y
Z X
Load 4
TUB160805.0
TUB160805.0
TUB160805.0
TUB160805.0
TUB160805.0
TUB80805.0
5.0
TUB80805.0
TUB160805.0
TUB80805.0
80 .0
05
TUB80805.0
.0 TUB160805.0
80 08 05
TUB80805.0
0
UB 08 05.
TUB80805.0
B8 TUB160805.0
TUB160805.0
B8 .0
T TU TU 808 80 805 5.0
UB 8080
T TUB TUB 0805.0
T UB8
TUB1001005.0 TUB1001005.0 TUB1001005.0 TUB1001005.0 TUB1001005.0 TUB1001005.0 TUB1001005.0
Y
Z X Load 1
Truss Type 2
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (mm2) (mm4) (mm4) (mm4)
1 TUB1201208.0TUB1201208.0 0.251 1.000 0.251 BS-4.7 (C) 203 3.52E+3 7.26E+6 7.26E+6 11.6E+6
2 TUB160805.0 TUB160805.0 0.155 1.000 0.155 BS-4.7 (C) 203 2.27E+3 7.44E+6 2.49E+6 6E+6
3 TUB2002006.3TUB2002006.3 0.183 1.000 0.183 BS-4.7 (C) 203 4.84E+3 30.1E+6 30.1E+6 46.5E+6
4 TUB1001006.0TUB1001006.0 0.067 1.000 0.067 BS-4.6 (T) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
5 TUB1201208.0TUB1201208.0 0.010 1.000 0.010 BS-4.6 (T) 202 3.52E+3 7.26E+6 7.26E+6 11.6E+6
6 TUB1201208.0TUB1201208.0 0.081 1.000 0.081 BS-4.6 (T) 203 3.52E+3 7.26E+6 7.26E+6 11.6E+6
7 TUB1201208.0TUB1201208.0 0.097 1.000 0.097 BS-4.6 (T) 203 3.52E+3 7.26E+6 7.26E+6 11.6E+6
8 TUB1201208.0TUB1201208.0 0.082 1.000 0.082 BS-4.6 (T) 203 3.52E+3 7.26E+6 7.26E+6 11.6E+6
9 TUB2002006.3TUB2002006.3 0.237 1.000 0.237 BS-4.7 (C) 203 4.84E+3 30.1E+6 30.1E+6 46.5E+6
10 TUB2002006.3TUB2002006.3 0.249 1.000 0.249 BS-4.7 (C) 203 4.84E+3 30.1E+6 30.1E+6 46.5E+6
11 TUB2002006.3TUB2002006.3 0.238 1.000 0.238 BS-4.7 (C) 203 4.84E+3 30.1E+6 30.1E+6 46.5E+6
12 TUB2002006.3TUB2002006.3 0.213 1.000 0.213 BS-4.7 (C) 203 4.84E+3 30.1E+6 30.1E+6 46.5E+6
13 TUB1001006.0TUB1001006.0 0.091 1.000 0.091 BS-4.7 (C) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
14 TUB1001006.0TUB1001006.0 0.039 1.000 0.039 BS-4.7 (C) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
15 TUB1001006.0TUB1001006.0 0.010 1.000 0.010 BS-4.7 (C) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
16 TUB1001006.0TUB1001006.0 0.015 1.000 0.015 BS-4.6 (T) 202 2.22E+3 3.23E+6 3.23E+6 5.13E+6
17 TUB1201208.0TUB1201208.0 0.253 1.000 0.253 BS-4.6 (T) 203 3.52E+3 7.26E+6 7.26E+6 11.6E+6
18 TUB1001006.0TUB1001006.0 0.126 1.000 0.126 BS-4.6 (T) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
19 TUB1001006.0TUB1001006.0 0.028 1.000 0.028 BS-4.6 (T) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
20 TUB1001006.0TUB1001006.0 0.030 1.000 0.030 BS-4.7 (C) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
21 TUB1001006.0TUB1001006.0 0.071 1.000 0.071 BS-4.7 (C) 203 2.22E+3 3.23E+6 3.23E+6 5.13E+6
22 TUB1201208.0TUB1201208.0 0.251 1.000 0.251 BS-4.7 (C) 203 3.52E+3 7.26E+6 7.26E+6 11.6E+6
23 TUB160805.0 TUB160805.0 0.125 1.000 0.125 BS-4.7 (C) 203 2.27E+3 7.44E+6 2.49E+6 6E+6
24 TUB2002006.3TUB2002006.3 0.163 1.000 0.163 BS-4.7 (C) 203 4.84E+3 30.1E+6 30.1E+6 46.5E+6
Job No Sheet No Rev
9
Part
Software licensed to
Job Title Custom Buildings Ref
Pu = 169.83 kN
Pu
Vu = 473.15 kN
Vu
300
Pu = 108.75 kN
Pu
Vu = 217.35 kN
Vu
250
Pu = 34.52 kN
Vu = 80.414 kN
Mu = 473.15 kN-m
Pu
Vu
500
500
APPENDIX: B
REFERENCE DRAWINGS
www.alpineburj.com commerce@alpineburj.com