Professional Documents
Culture Documents
Parking Brake Actuator - Remove and Install PDF
Parking Brake Actuator - Remove and Install PDF
Page 1 of 5
Shutdown SIS
Previous Screen
i02343632
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-5230 Hand Hydraulic Pump 1
B 155-3597 Wheel Chock 4
Start By:
A. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock -
Separate and Connect".
B. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure -
Release".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 4/4/2020
962H WHEEL LOADER J6J00001-UP (MACHINE) POWERED BY C7 ENGINE(XEB... Page 2 of 5
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g01169584
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 4/4/2020
962H WHEEL LOADER J6J00001-UP (MACHINE) POWERED BY C7 ENGINE(XEB... Page 3 of 5
Illustration 2 g01169585
3. Install Tooling (A) onto parking brake actuator (2). Use Tooling (A) to release the tension on
the reaction arm of the parking brake.
Illustration 3 g01169587
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-5230 Hand Hydraulic Pump 1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 4/4/2020
962H WHEEL LOADER J6J00001-UP (MACHINE) POWERED BY C7 ENGINE(XEB... Page 4 of 5
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint
may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement.
Illustration 4 g01169585
Illustration 5 g01169587
3. Use Tooling (A) to extend the yoke of parking brake actuator (2) and install pin (4) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 4/4/2020
962H WHEEL LOADER J6J00001-UP (MACHINE) POWERED BY C7 ENGINE(XEB... Page 5 of 5
Illustration 6 g01169584
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame
Lock - Separate and Connect".
Copyright 1993 - 2020 Caterpillar Inc. Sat Apr 4 08:39:33 EST 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 4/4/2020