Professional Documents
Culture Documents
User Manual
Do not install by users, installation should be
done by dealer or the authorized Installation
Company, or it will affect machine
Warning performance.
We reserve the rights for our products improvement without prior notice! Before using, please read the user manual carefully and keep it for future reference!
WIRE DIAGRAM
Catalogue
*** For circulation type heat pump,no need connect water pressure switch,thermostat and water output temperature meter
User Guide...........................................................................2
Installation............................................................................5
Cover
Introduction Diagram...........................................................10
*** All power output can not connect to big machine,electric heater needs add A/C connector
Error Code Table.................................................................11
Public point
High pressure
Low pressure
*** The public point between water level and high-low pressure is forbidden to connect.
Public point
Crank heater
To wire controller
Thermostat
Electric heater
4-way valve
Output 2(Blue)
Wire Diagram......................................................................19
4-way valve
Defrosting temperature
Output 1(Blue)
White
Suction temperature
Blue
Return water temperature
Input(Red)
TR
Ambient temperature
Current
N
NC
NC
A1
A2
Compressor
White
L3
Red
L3
C
L2
L2
L1
Blue
S
L1
Yellow/Green
AC Connector R
(220V/50Hz coil)
Fan
Capacitor
Black White
M
Yellow/Green
Terminal-1
Yellow/Green
GND
N
L
220V/50-60HZ ~
21
WIRE DIAGRAM INTRODUCTION OF PRODUCTS
Air-source pump water heater apply the air source pump theory, The refrigerant absorb the
Terminal-2
heat from air ,and compress into the gas with a high pressure and temperature by
N
compressor, then transmit the heat to water by heating exchanger, it is a effective way to heat
For circulation type heat pump,no need connect water pressure switch,thermostat and water output temperature meter
ⅠThe advantages of recycle commercial HPWH
1-Temperature of water is easy to adjust ,and have a wider apply even in all kinds of projects
2-Having a high stability in water yield.
High pressure switch 1
Public point
Anti frozen switch
All power output can not connect to big machine,electric heater needs add A/C connector
To wire controller
Fan 2 3-The heating exchange system have a constant water recycle ,it will make a adequate water
The public point between water level and high-low pressure is forbidden to connect.
Fan 1
Electronic expansion valve 2
exchange.
Crank heater
Compressor 2
Discharge temperature 2
Water output
Compressor 1
Discharge temperature 1
ⅡThe Applicable scope
Defrosting temperature 2
Anti frozen
Suction temperature 2
This product can work in all reasons all-day, without the effect of weather, using in the
temperature of -7~43(-25~43 is available), applied in residential area, villa, public bathing room,
Thermostat
Suction temperature 1 swimming pool, hotel, school, hospital ,factory ,and so on.
4-way valve
CN3
CN2
Output 2(Blue)
Water pump
Input(Red)
2#AWY
1#AWY
ⅢThe feature of products
Electric heater
B phase
Three
C check
TR
1-Energy saving:The energy consumption is only 25% of same capacity electricity heater
A
2-Security:The heat of air-source pump water heater come from air ,not the electricity or other
fuel, avoid a danger from electricity leakage ,dry-burning explosion, poisoning.
Brown
Blue
Red
Fan 2
Black White
Capacitor
M
3-Environment protection: There are no polluted gas for using the air sources heating, belong to
Yellow/Green
Capacitor
M
Yellow/Green
4-High Tech: adapt the microcomputer control system ,melt the frost intelligently, with a strong
To low pressure switch 1
2
Compressor 1 Yellow/Green Compressor
adaptability
NC
NC
A2
A1
White
T3 T1
Red Red
T2
Brown Brown
Blue Blue
To low pressure switch 1
Relay
AC Connector
T3 T1
Red Red
M
T2
Brown Brown
Blue
Blue
AC Connector
Relay
Yellow/Green
Yellow/Green
(2)Double system
Terminal-1
380-440V/50-60Hz~
20 1
USER GUIDE WIRE DIAGRAM
Notice:
Terminal-2
4-Tthe flashlight and other electromagnetic radiation source will affect the machine, if it occurs
Cover
For circulation type heat pump,no need connect water pressure switch,thermostat and water output temperature meter
, pls cut off the power,and restart it when the phenomenon disappears.
5-Do not stock or cover the exhaust exit or the space of machine.
Public point
Public point
Crank heater
Safety Notices
Water supply pump
All power output can not connect to big machine,electric heater needs add A/C connector
Please make sure you have read this guidance before using, pls operate it according this
Thermostat
To wire controller
Electric heater
The public point between water level and high-low pressure is forbidden to connect.
Water input valve
Water pump
Output water temperature
Wrong to operate this machine will cause the accident of death, injure, harmfulness
Fan Discharge temperature 1
4-way valve
Output 2(Blue)
Defrosting temperature
Output 1(Blue)
Notices Suction temperature
White
Improper to use machine will result accident, the harm of machine ,and degrade the
Blue
Return water temperature
performance of machine ,please read the label of mainframe . any abnormal condition ,l ike
Input(Red)
TR
Ambient temperature
phase
Three
check
abnormal noisy, oder,smog ,rising temperature, electricity leakage, visible fire, please cut off
C
A
B
Current
N
the electricity ,call the dealer or provider ,if need ,please call the apparatus ,
Brown
Red
Blue
Warnings
NC
NC
A1
A2
1-Do not install by user himself, installation should be done by dealer or the authorized White
Compressor
T1
Red Red
M
Installation Company, or it will affect machine performance.
T2
Brown Brown
T3
Blue Blue
2-Except the professional direction, any unprofessional persons are not allow to open the
Yellow/Green
Relay
AC Connector
machine, or which will damage the machine. If the electricity wire is broken ,please call the
appointed maintenance center or professional engineer to change.\
Capacitor
Black White
Fan 1
3-Do not use the flammable substance, like oil, alcohol, paint, petrol, which can cause fire.
4- Put the main power switch in the place out of touch of child in case of any danger.
(1)Single system
Yellow/Green
5-Do not sprinkle any water or liquid on machine in case of the electric shock
GND
Yellow/Green
R
N
S
T
6-Do not touch machine with wed hand in case electric shock
7- Switch off in stormy weather in case flashlight shock
8-Please cut it off when stopping using . 380-440V/50-60Hz~
2 19
INTRODUCTION FOR PARAMETER USER GUIDE
Using notice
1- Do not open or cut off the machine frequently to avoiding any harmfulness to machine
2-The machine' operating parameter and the settings of protection device is ready after
factory, please do not change it casually, and protect the protection units from short circuit ,
or it will damage the machine
3-The refrigerant used in the machine non-poisonous and non-flammable, due to it is heavier
than air, the refrigerant will cover on floor when leakage. so please keep a good air fluency to
avoid choke.
4- When cleaning the machine, to wipe it with neutral water, do not using acidic material or
alkaline material which can cause a color-fade and malfunction the button
5-If having the leakage of refrigerant, please contact with the maintenance center, and notice,
do not have any visible fire in working site ,because the refrigerant will decompose the
poisonous gas when meeting the fire
6-Stop the machine and keep the connection with electricity under the 0℃ weather for
protecting the water system pipe from frost freezing, if customer will stop using for a long
time ,please cut off the power source and exhaust the water.
18 3
安装说明书
USER GUIDE INTRODUCTION FOR DISPLAY BOARD
7 -The water switch have a great protect importance to the cooling water system ,so the Timer setting:
machine should attach a standardized switch and import the protection signal into output Touch this key to enter to set main unit Timer ON/Timer OFF. At the beginning, adjust
block of water switch, as for the exterior connection system of water pump, please input the
the first phase Timer ON, press to adjust Hour, Touch timer key again, press to
signal into corresponding terminals, and should keep the electric-control board a good
adjust Minute. Touch timer key again, adjust the first phase Timer OFF, press to adjust
sensibility to water pump
Hour, Touch timer key again, press to adjust Minute.
8-Do not start the compressor frequently for extending the longevity of machine (no more
Touch timer key again to enter to, second phase Timer ON/Timer OFF.
than 5 times in one hour),
All Timer ON/OFF finish to quit, the marks will show on the display.
9- DO not pull or distort the electricity wire for avoiding any shock case
10 In case of any accidents, please do not touch any electricity units or buttons when Show it is the timer for first phase
Set Out
11 If there are any problems about machine , please do not mend it by yourself ,and call the
serviceman or sales center , any unprofessional mend will arouse the damage of machine or
even people safety events
Timer on for first phase ON
12- please maintain the machine according to the direction book for keeping a good state of
machine
4 17
INTRODUCTION FOR DISPLAY BOARD INSTALLATION
16 5
INSTALLATION INTRODUCTION FOR DISPLAY BOARD
Remarks: before installation, please check the components, and make sure everything is
ready, Setting Temp. Water Temp.
4 Take the records of inspection c.Water temperature set:Under ON, press the COLD/HEAT CMP ON
Accessories name
processing, the symbols of ″set temperature″
1-outside packing will flash and the set water temperature will
Machines examination
2-whole unit examination change.
ON
3- PCB examination
4-fan and motors examination d.Parameter check: Under On, press the key of
5-others
Function to check running parameter.
1-User Manual
Technical Docs
2-Warranty Card
examination
3-Others Timer Function
6 15
FUNCTION DESCRIPTION INSTALLATION
14 7
INSTALLATION FUNCTION DESCRIPTION
Ⅳ the inspection of power source After 60 seconds ,if return water temperature < 5℃, the compressor will be working. The
machine will be off when the temperature of water tank reaches 15℃, otherwise, it is off until 60
1 Before installation ,please check the capacity ,wire, switch of power source ,and maek sure seconds after enter first anti-frozen.
they can support the running of machine. 5.Four-way valves: When cooling power off, heating power on. The compressor is working for 20
2-The power source of machine should extend the electricity wire from power switch , and seconds at the beginning , the four-way valves will power off after 10 seconds.
make sure the power source and voltage reach the standards 6.Crankshaft heating: If environment temperature < 8℃ and compressor was off over 1 minute,
then crankshaft heating will working. Before 1 minute of the compressor reaches the starting
condition and environment temperature > 10℃,crankshaft heating off. And it off when
Ⅴ- Important notices environment sensor default.
1-safety notices : 7.Auxiliary Electric heater: When environment temperature ≤ 10℃, it starts. When
environment temperature ≥ 12℃, it off.
It will cause safety problem in below install situation
A-The installation site with mineral oil ,like the oil of cutting machine 8.Water pump mode: Normal mode: the return water temperature reaches the set temperature
not stopping. Special mode: the return water temperature reaches the set temperature stopping.
B-The installation site with a lot of salts in the air ,like seaside
C-The installation site with erosion gas ,like the sulfur in spring 9.Defrosting electric heating control: On only defrosting.
D-The installation site with a heavy fluctuation in voltage and current ,like the factory 10.Safety valve control: When environment temperature > 5℃ and discharge temperature >
E-The car or cabin ,some place similarly 105℃, it starts. When environment temperature < 5℃ and discharge temperature >5 ℃ return
F-The kitchen with a lot of oil gas water temperature, it starts. When discharge temperature < 2 ℃ return water temperature, it
closes.
G-The installation site with a strong fluctuation of electromagnetic wave
H-The installation site with flammable gas and material 11.Anti cold wind relay: On cooling starts. On heating, if return water temperature ≤35℃ ,it
closes. But > 37℃, it starts.
I-The installation site with the existence of acidic gas or alkaline gas.
J-The installation site with other special conditions Protection function
2-The cautions before installation 1. The compressor have 3 minutes delay protection, the shortest operation time of same
compressor is 90 seconds, the interval for start/ stop of different compressor is 10 seconds.
A-Choose the right carrying way
2. When the circulating water pump running, if the water flow switch off for 10 seconds, the
B-Carry machine at the original package
compressor and water pump will power off. After 3 minutes automatically reset and unlock.
C-If the machine will be installed on metal base , insulate issue must be considered ,and
3. Anti-frozen switch: When anti-frozen switch continued to off for 2 seconds, the compressor
obey the corresponding standards immediately stop. After the anti-frozen switch on, it will automatically resume operation.
4. High pressure protection:( high pressure switch power off ) In 3 times/hour, the display board is
Ⅵ-The key-point of installation not shows ″pressure protection″. After pressure recovery, the compressor re-start after 3
minutes; Over 3 times/hour, the controller will lock this default. The compressor can not re-start
1-Installation Confirm the model ,serial number ,name before installation whether or not pressure switch reset. The display board shows error code.
2- Electricity lines allocation: 5. Low pressure protection: In defrosting not detect the low pressure switch. It will be detect on
A-The power capacity and the route of electricity wire should heating and cooling working after 3 minutes. Then ( high pressure switch power off ) in 3
times/hour,the display board is not shows ″pressure protection ″. After pressure recovery, the
be chose according to design manual ,the diameter of compressor re-start after 3 minutes; Over 3 times/hour, the controller will lock this default. The
machine electricity wire should be larger than the ordinary one compressor can not re-start whether or not pressure switch reset. The display board shows error
B-And make sure whether the earth wire is effective code.
3-Trial running: Only the machine connect the power more 6. Sensor fault:
than 12 h ,can user take a test run a. Environment sensor fault: Stop and the display board shows error code. The machine is
running properly after recover.
4-The connection and installation of machine pipe : when
b. Coil sensor fault: Stop and the display board shows error code. The machine is running
connecting the water inlet pipe and water outlet pipe of properly after recover.
machine , please use two pliers on these two joints ,and
c. Out put water sensor fault: The machine is stop.
make sure the pipes no moving .(refer to following picture)
8 13
FUNCTION DESCRIPTION INSTALLATION
1.Cooling operation: When the mode set cooling, the display board shows ″cooling″.
Operation methods:after turn on the machine, press the + button for 5 seconds to enter. Lifting &Packing Instruction.
Symbols explain: Tw - Return water temperature . Ts - user set temperature.
(1), It should be consider the weight of unit when lifting, the lifting rope load must be more
Compressor ON condition: when Tw = Ts+3℃,turn on two compressors.
2.5 times than the unit weight, the protection pad and wooden bearing should be put on the
Compressor OFF condition: when Tw = Ts-2℃,turn off two compressors.
surface of unit to avoid the scratch and deformation of metal plate surface.
Cooling on process : Turn on → water pump on→ water flow switch detect → fan on →
(2).Keep level position when the units are moved and lifted; heeling more than 20 degree is
compressor 1 on →compressor 2 on
prohibited.
Cooling off process: compressors off → fan off → water pump off( according to the specific
parameter set ) (3).The lifting should be handled with care; the unit must be bear the force equally. It should
be meet the safety regulations of local construction plant when lifting and transportation, it
2.Heating operation: When the mode set heating ,the display board shows″heating″.
Operation methods:after turn on the machine, press the + button for 5 seconds to enter. should be operated by qualified workers with precautionary measures to guarantee the safety
a. Compressor ON condition: when Tw = Ts+3℃,turn on two compressors. of people and equipment.
12 9
INSTALLATION DIAGRAM ERROR CODE TABLE
Warm notice:If fault happens, the display shows error code and flashes.
10 11