Professional Documents
Culture Documents
Wang2012 PDF
Wang2012 PDF
Micro-forming as a kind of metal forming process is very suitable for massive produc-
tion of micro-parts with high mechanical properties. To eliminate the scaling effects
of friction in micro-forming, diamond-like carbon (DLC) film of nano-thickness was
deposited on the micro mould with plasma based ion implantation and deposition
(PBII&D) method for its excellent tribological behaviors. The effects of mould cavity
dimensions were investigated, for example distribution of thickness, surface topogra-
phy and microstructure of DLC film. The result shows that the thickness of DLC film
decreases from 554 nm to 47 nm with the increasing of depth into mould cavity. And
ripple topography appears when the cavity dimension is small. The ratio between ID
and IG increases with the increasing of cavity dimension, which means that the amount
of SP3 bonds becomes smaller. With the DLC film deposited female die, micro-cups of
1.1 mm in diameter were manufactured successfully using copper thin sheet of 0.04 mm
in thickness with a blanking-deep drawing process. And the surface quality and dimen-
sion accuracy of micro-cup were analyzed in details. The results show that DLC film is
feasible alternative to micro-forming.
Keywords Micro-forming; thin solid film; DLC film; scaling effect; micro-cup
1. Introduction
Micro-forming is an appropriate massive production technology for very small metal parts
with at least two dimensions in the sub-millimeter range. During the miniaturization of parts,
scaling effects occurs clearly, and the traditional knowledge of macro metal forming can
not be transferred into micro-forming directly. One of the scaling effects is the coefficient
of friction for the increasing of ratio between surface and volume of micro-parts when a
liquid lubricant is applied [1, 2]. For low friction and wear rate, diamond-like carbon (DLC)
film attracts more attentions in recent decade. Lackner employed a pulsed laser deposition
method and investigated the structural, mechanical and tribological properties of DLC film
coated on several kinds of steel substrates for industrial applications [3]. A metal coaxial
radio-frequency (RF) electrode was utilized to produce plasma and deposit film onto the
inner wall of the tubes. The non-uniformity of thickness of deposited films and plasma
[205]/35
36/[206] Chunju Wang et al.
density in the bore were investigated with tubes of different lengths and inner diameters
[4]. To deposit on the inner surface of micro-hole, the effect of argon gas was discussed and
a micro-coating method was discovered [5]. In micro-forming process, DLC film on surface
of the die was deposited by Yang to improve wear-resistance and reduce friction, and a
micro single-side bending test was carried out for evaluation of wear-resistance of the DLC
film [6, 7]. When the micro-extrusion mould was deposited by DLC film, the maximum
extrusion force decreased from 32kN for uncoated die to 25 kN [8]. In our research group,
DLC film was applied to micro-deep drawing, and the micro-cup of large limit drawing
ratio was deep drawn successfully [9].
In the paper, a nano-thickness of DLC film was deposited on the inner surface of micro-
cavity. The effect of die cavity dimension was investigated. With DLC coated mould, the
micro-cup of 1.1 mm in diameter was deep drawn successfully with 0.04 mm copper thin
sheet.
2. Foundation of Experiment
A serial of two-body moulds with micro-channel were manufactured with the tool steel
JIS-SKD11. The widths t of micro-channel are different from 0.6 mm to 1.2 mm, and the
radius R of edge corner at opening side is 0.3 mm as shown in Fig. 1. To improve the
adhesion between DLC film and mould, the surface of cavity was polished to Ra 0.1µm.
The DLC film was deposited on surface of mould by the plasma based ion implantation
and deposition (PBII&D) process. Before the deposition of DLC film, a very thin nitrogen
layer as buffer film was formed at the base pressure of 0.3 Pa and pulse voltage of 15 kv.
Then, the DLC film was deposited with pulse voltage of 15 kv, and radio-frequency power
was selected as 200 w.
The surface topography and cross section of DLC film were observed by a SEM
(HITACHI, S-4300), and the thickness of film was calculated using the comparing rule.
The microstructure was analyzed with Raman spectra (JY, HR800) with excitation laser
wavelength of 532 nm at power of 0.1 mw.
To locate small specimen accurately, a complex blanking-deep drawing multiple oper-
ation mould was developed as shown in reference 9. The first step is preparing a thin sheet
specimen of 2.0 mm in diameter using blanking method. Then, the specimen was deep
drawn to a micro-cup of 1.1 mm in the inner diameter with the limit deep drawing ratio of
1.8. The pure copper thin sheet of 0.04 mm in thickness was selected in the investigation.
To analyze the quality of micro-cup, the SEM and confocal laser scanning microscope
(Olympus, OLS3000) was applied.
Table 1
Thickness of DLC film at points of different depth
Figure 2. Surface topography of film coated on micro-mould (t = 0.6 mm) for (a) Top surface, (b)
Inner surface at depth of 0.5mm, (c) Inner surface at depth of 1.0 mm, (d) Inner surface at depth of
1.5 mm.
Figure 3. Surface topography of DLC film coated on micro-mould (t = 0.8 mm) for (a) Inner surface
at depth of 0.5 mm, (b) Inner surface at depth of 1.0 mm.
Properties of DLC Film [209]/39
ID/IG G
25000
0.6mm 2.86
0.8mm 2.94 D
20000 1.0mm 2.57
1.2mm 2.49
1.4mm 2.31
Intensity (a.u.)
15000
10000
5000
0
800 1000 1200 1400 1600 1800 2000
To analyze the results in details, two kinds of measurement points, which depths into
micro-cavity from the top surface are 0.5 mm and 1.0 mm, are selected. The ratio between
ID and IG are calculated using the Gauss fitting curves to analyze the relative amount
of SP3 bonds and SP2 bonds. The results show that the ratio of ID/IG decreases with the
increase of channel width, which means that the amount of SP3 bonds becomes larger. So,
the mechanical properties of DLC film on micro-cavity of big width are better than that of
small width. When the width of channel is 1.4 mm, the ratio of ID/IG is close to 2.23 of top
surface. It indicates that the properties of DLC film on inner surface near to the top surface
are almost the same as that of top surface. It is very suitable for application in micro-deep
drawing.
11000
ID/IG G
10000
0.5mm 2.86
9000 1.0mm 2.89
1.5mm 3.01 D
8000
Intensity (a.u.)
7000
6000
5000
4000
3000
2000
The effect of depths into micro-cavity is shown in Fig. 5. When the depth is small,
the ratio of ID/IG is almost the same. However, when the depth increases to 1.5 mm, the
ratio of ID/IG becomes big. The reason is that the energy of ion decreases quickly with the
increasing of depth into micro-cavity.
55
PE Film
DLC Film
50
Thickness (P)
45
40
35
30
0 2 4 6 8 10 12 14 16 18 20
Measure points
the rim as shown in Fig. 6. The result is compared with that obtained on lubrication of PE
film which possesses very lower coefficient of friction as a solid lubricant. The fact that
the punch load is almost the same means that DLC film owns super tribological properties.
And the surface quality is better than that using PE film. The reason is that PE film is easily
broken and accumulated at the corner of female die, and it leads to wrinkles in the rim of
micro-cup.
The thickness of wall was measured at different corner points of micro-cup as shown
in Fig. 7. From point 6 to 14, the results show the reduction of thickness at the bottom
corner of micro-up. When the PE film is applied, the reduction of thickness is much bigger
than that of DLC film. The micro-cup obtained with PE film becomes easily broken for
the small strength induced by the big reduction of thickness. The comparison between
DLC film and PE film indicates that the DLC film is very suitable for the micro-deep
drawing.
4. Conclusions
DLC film was deposited on micro mould used in micro-forming with PBII&D. With
the increasing of depth into micro-cavity, the thickness of DLC film decreases quickly.
Fortunately, the thickness of DLC film is big at the corner of opening side. The width of
channel and depth into micro-cavity have obvious effects on the forming of ripple on the
inner surface of micro-cavity. The ratio ID/IG decreases with the increasing of the channel
width and depth into micro-cavity, which means that the amount of SP3 bonds becomes
larger. With DLC coated mould, the micro-cup was successfully deep drawn with smooth
surface in rim and small reduction of thickness at bottom corner.
Acknowledgments
The authors gratefully acknowledge the financial support of the National Science Founda-
tion of China (No. 50835002 and No. 50805035), the Foundation for Innovation Scholars
of Harbin (2008RFQXG041) and Key Laboratory Opening Funding of Micro-systems and
Micro-structures Manufacturing (Ministry of Education) (HIT. KLOF. 2009008). Authors
would like to thank Prof. Xiubo Tian for the help of DLC film deposition.
References
1. F. Vollertsen, Z. Hu, H. S. Niehoff, and C. Theiler, State of the art in micro forming and investi-
gations into micro deep drawing. J. Mater. Process. Tech. 151, 70–79 (2004).
2. J. Jeswiet, M. Geiger, U. Engel, et al., Metal forming progress since 2000. CIRP J. Manu. Sci.
Techolo. 1, 2–17 (2008).
3. J. M. Lackner, C. Stotter, W. Waldhauser, R. Ebner, W. Lenz, and M. Beutl. Pulsed laser deposi-
tion of diamond-like carbon coatings for industrial tribological applications. Sur. Coat. Tecnolo.
174–175, 402–407 (2003).
4. J. T. Cui, X. B. Tian, S. Q. et al., Plasma distribution in the slender bore excited by coaxial rf
electrode. Sur. Coat. Tecnolo. 201, 6651–6654 (2007).
5. X. D. Yang, T. Saito, Y. Nakamura, Y. Kondo, N. Ohtake, Mechanical properties of DLC
films prepared inside of micro-holes by pulse plasma CVD. Dia. Relat. Mater. 13, 1984–1988
(2004).
6. K. Fujimoto, M. Yang, M. Hotta, H. Koyama, S. Nakano, K. Morikawa, and J. Cairney, Fabrication
of dies in micro-scale for micro-sheet metal forming. J. Mater. Process. Tech. 177, 639–643 (2006).
42/[212] Chunju Wang et al.
7. M. Yang, K. Manabe, and K. Ito, Micro press forming and assembling of micro parts in a
progressive die. J. Mech. Sci. Technol. 21, 1338–1343 (2007).
8. N. Takatsuji, K. Dohda, et al., “Friction behavior in aluminum micro-extrusion” in International
Conference on Tribology in Manufacture Processes-2007, pp. 157–162.
9. F. Gong, B. Guo, C. J. Wang, D. B. Shan, Micro deep drawing of micro cups by using DLC film
coated blank holders and dies. Dia. Relat. Mater. 20, 196–200 (2010).
Copyright of Integrated Ferroelectrics is the property of Taylor & Francis Ltd and its content may not be copied
or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission.
However, users may print, download, or email articles for individual use.