Professional Documents
Culture Documents
and Implications
Definitions
• Band B1
– Frequency band, e.g. 2100 MHz, 900 MHz
– Possible to support within IBW of one Radio Unit B2
– Denomination B1, B2, B3, etc.
f1
• Carrier
– One 5 MHz slot of the frequency band f2
– Denomination f1, f2, f3, etc.
• Cell-carrier f1
– One carrier in one physical direction
f2
S1
• Sector (Logical) S3 S2
– Cell-carriers in the same frequency band directed in f1
the same physical direction – with or without MIMO
– Denomination S1, S2, S3, etc. f2
S1 S4
• Sector (Physical) S3 S2
– All logical sectors in the same physical direction B1
B2
S6 S5
Configuration types
• Basic Configuration
– Configurations according to the original rules
• Advanced Configuration
– New alternative configurations
• Flexible Configuration
– Free mapping of carriers in RBS 6000
Configuration Roadmap
Í Basic ÎÍ
RBS3000 & RBS6000
Advanced ÎÍ Flexible Î
3x2
Advanced
Single Band Up to
Up to 6x2
in 2 BB pools 3x2+3x2 RBS3000
with MC/EUL
Up to Dual Band
3x2+3x2 With
Dual Band Single
Band
MC / EUL DUW in RBS3000
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of
2 DUW.
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
5. Dual Band shall always be seen as a 6-sector with or sub equipped 6-sector
configuration, i.e. at least one of sector 4, 5 or 6 is used. Maximum 2 carriers per
sector are allowed.
PrerequisiteS
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of
2 DUW.
Î No support of 1xDUW 1x3, 1x4, 3+1+1+1, or 2xDUW 3+3+2+2 or 4+3+2+1
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
Î No support of 1xDUW 2+1+1+1, or 1xDUW 2x2 + 2x1
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
Î No support of 4+1+4+3 (4+3 sector-carriers not possible to fit in to one DUW)
5. Dual Band shall always be seen as a 6-sector with or sub equipped 6-sector
configuration, i.e. at least one of sector 4, 5 or 6 is used. Maximum 2 carriers per
sector are allowed.
Î No support of 2xDUW 3x3 + 3x1 Dual band
Multi carrier (DC) – One RBS
node
3x2 DC 4x2 DC
DualCarrier- DualCarrier- DualCarrier- 4x2 are 8 CCs (more than 6) and would therefore need 2
Sector 1 Sector 2 Sector 3 BB-Pools, but:
Carrier 1
Two cells forming a Dual Carrier-
Sector must belong to the same
Carrier 2 BB-Pool. DC-
Sectors: 1 2 3 4
The requirement
3x2 are 6 CCs, ok with 1 BB-Pool conflicts with a BB-Pool 1
Baseband-Pool- BB-Pool 2
configuration like this:
RBS 6000:
The dual BB pool configurations 4x2 (and 5x2, 6x2) are EUL-supported by W10B
feature ’FAJ 121 1518, EUL for large RBS configurations’:
The EUL supported dual baseband pool configurations based on DUW/RUW
(RBS 6000) are: 3x3, 3x4, 6x2, 3x2+3x2 (dual band).
DC ...Dual Carrier Therefore, a BB-pool configuration over
CC ...Cell-Carrier BB-Pool 1
4 sectors like this is ok with RBS 6000
BB-Pool ...Baseband-Pool since 9th of Nov 2010: BB-Pool 2
& EUL
WITH two RBS NODES
4x2 by 2 logical RBSs Issues to consider with this solution:
DualCarrier- DualCarrier- DualCarrier- DualCarrier- • Softer HO only between sectors 1/2 and 3/4
Sector 1 Sector 2 Sector 3 & 4 Sector 4 • Soft HO between sectors 2/3 and 4/1
SoHO SoHO
(f1), 6x1
+ IFHO IFHO
(f2), 6x1
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of 2
DUW.
Î No support of 1xDUW 1x3, 1x4, 3+1+1+1, or 2xDUW 3+3+2+2 or 4+3+2+1
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
Î No support of 1xDUW 2+1+1+1, or 1xDUW 2x2 + 2x1
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
Î No support of 4+1+4+3 (4+3 sector-carriers not possible to fit in to one DUW)
5. Dual Band shall always be seen as a 6-sector with or sub equipped 6-sector
configuration, i.e. at least one of sector 4, 5 or 6 is used. Maximum 2 carriers per
sector are allowed.
Î No support of 2xDUW 3x3 + 3x1 Dual band
Current solution with one
DUW 2100MHz
1x 1x 1x 1x 1x
2100MHz RRUW
0 1 2 3 4
900MHz
1x O O No No
IP Iub
CPRI --
0 K K k k
900MHz RRUS
1x O O O No No
1 K K K k k
O configuration
1xFlexible O O No for No
2 1xDUW
K Kfor up K to 1x4:
k k
One BB pool can handle 6 cell-carriers
1x No No No No No
3 RBSk6000kCandidate
¾ k for k W12Bk
More than 2 carriers in Sector
2+1+1+1 3+1+1+1
Carrier 1 Carrier 1
Carrier 2 Carrier 2
Carrier 3
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of 2
DUW.
Î No support of 1xDUW 1x3, 1x4, 3+1+1+1, or 2xDUW 3+3+2+2 or 4+3+2+1
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
Î No support of 1xDUW 2+1+1+1, or 1xDUW 2x2 + 2x1
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
Î No support of 4+1+4+3 (4+3 sector-carriers not possible to fit in to one DUW)
5. Dual Band shall always be seen as a 6-sector with or sub equipped 6-sector
configuration, i.e. at least one of sector 4, 5 or 6 is used. Maximum 2 carriers per
sector are allowed.
Î No support of 2xDUW 3x3 + 3x1 Dual band
Current solution with one
DUW
2100MHz
2100MHz RRUW
2x 2x 2x 2x
900MHz
IP Iub
CPRI 0 1 2 3
2x O O O No
900MHz RRUS
0 K K K k
2x O configuration
Flexible O No for No
In Dual Band configurations, 1 1xDUW
K Kfor upk to: k
sectors for the frequency bands are
counted separately
2x2x1O+ 2x2No
Dual Band
No No
and then added together 2 K ork2x3 k k
(Logical sectors) ¾ RBS 6000 Candidate for W12B
2x No No No No
3 k k k k
ConFig Rule 4
1. More than 3 sectors Î 6-sector or sub equipped 6-sector configuration.
Î No support of 4x2 or 6x2 in combination with Multi-Carrier
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of 2
DUW.
Î No support of 1xDUW 1x3, 1x4, 3+1+1+1, or 2xDUW 3+3+2+2 or 4+3+2+1
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
Î No support of 1xDUW 2+1+1+1, or 1xDUW 2x2 + 2x1
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
Î No support of 4+1+4+3 (4+3 sector-carriers not possible to fit in to one DUW)
5. Dual Band shall always be seen as a 6-sector with or sub equipped 6-sector
configuration, i.e. at least one of sector 4, 5 or 6 is used. Maximum 2 carriers per
sector are allowed.
Î No support of 2xDUW 3x3 + 3x1 Dual band
Carriers can not be splitted
4+2+4 4+2+4+1
Carrier 1 Carrier 1
Carrier 2 Carrier 2
Carrier 3
Carrier 3
Carrier 4
Carrier 4
Flexible configuration:
¾ RBS 6000 Candidate for W12B
DC ...DualCarrier
CC ...Cell-Carrier
BB-Pool ...Baseband-Pool
4/10/2015
ConFig Rule 5
1. More than 3 sectors Î 6-sector or sub equipped 6-sector configuration.
Î No support of 4x2 or 6x2 in combination with Multi-Carrier
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of
2 DUW.
Î No support of 1xDUW 1x3, 1x4, 3+1+1+1, or 2xDUW 3+3+2+2 or 4+3+2+1
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
Î No support of 1xDUW 2+1+1+1, or 1xDUW 2x2 + 2x1
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
Î No support of 4+1+4+3 (4+3 sector-carriers not possible to fit in to one DUW)
5. Dual Band shall always be seen as a 6-sector with or sub equipped 6-sector
configuration, i.e. at least one of sector 4, 5 or 6 is used. Maximum 2 carriers per
sector are allowed.
Î No support of 2xDUW 3x3 + 3x1 Dual band
rakesh bhayanaxzcxcx
DUAL Band configuration
(no MIMO) – Single node
3x2 + 3x1 3x3 + 3x1
2 DUW + 3 RUS2100 + 3 RUS850
2100 f3
2100 f2 850 f1 W850 3x1
W850 3x1 2nd f4 20W
2nd f3 20W DUW
DUW f4
f3
f4
f3
DBB21_02
DBB21_02 RBB12_1A
RBB12_1A
Advanced configuration:
f1 f2to consider with this solution:
Issues ¾ Candidate for W12A
• Multi-Carrier within band not supported
• EUL in 2 BB pools supported
See next slide for interim 2 RBS Node solutions
DUAL Band configuration
(no MIMO) – Single node
3x3 + 3x1
2100 f3
850 f1 W850 3x1
2nd f4 20W
DUW f4
f4
DBB21_02
RBB12_1A
Advanced configuration:
¾ Candidate for W12A
Dual Band configuration
(no MIMO) – Two RBS nodes
3x3 + 3x1 Two nodes 3x3 + 3x1 Two nodes
3 DUW + 3 RUS2100 + 3 RUS850 2 DUW + 6 RUS2100 + 3 RUS850
f3
f3
W850 3x1 W2100 3x1
2nd f4 40W* 2nd 20W*
DUW DUW f3
f4
f4
DBB21_01
2100MHz RRUW 1x 1x 1x 1x
1 2 3 4
900MHz
IP Iub
CPRI
1x O O O O
IDL
1 K K K K 2100MHz
900MHz RRUS
1x O O O O
2 2x K 2x K 2x K 2x K
900MHz
1 2 3 4
Two BB pools can handle 12 cell-carriers 1x O O O O
2x
3 O K O K No K No K
1Flexible
K configuration
K k kfor
2xDUW for up to 2x3 + 2x3:
2x O O No No
2 K K k k
¾ RBS 6000 Candidate for W12B
2x No No No -
Rephrased ConFig Rule 5
1. More than 3 sectors Î 6-sector or sub equipped 6-sector configuration.
Î No support of 4x2 or 6x2 in combination with Multi-Carrier
2. More than 2 carriers in any sector = max 3-sectors to be used and requires use of
2 DUW.
Î No support of 1xDUW 1x3, 1x4, 3+1+1+1, or 2xDUW 3+3+2+2 or 4+3+2+1
3. More than 1 carrier in any sector and more than 3 sectors = use of 2 DUW.
Î No support of 1xDUW 2+1+1+1, or 1xDUW 2x2 + 2x1
4. One carrier shall not be splitted between DUWs, for ex. f1 shall be only handled by
DUW1 and f2 only by DUW2.
Î No support of 4+1+4+3 (4+3 sector-carriers not possible to fit in to one DUW)
5. Dual Band is always built up as separate sectors per band, i.e. 3x2+3x2 require use
of 6-sectors. Maximum 2 carriers per sector are allowed if more than 3-sectors are
used.
Î Support of 2xDUW 1x3 + 1x1 Dual band
Dual Band configuration
(no MIMO)
1x3 + 1x1 1x3 + 1x1
2 DUW + 1 RUS2100 + 1 RUS850 1 DUW + 1 RUS2100 + 1 RUS850
RBB12_1A
DBB21_01
MIMO
f1 f1
MIMO
f2 f2
DBB21_01
f2 f2
¾ Support in RBS 6000
RBB22_1A from April 21, 2011 in
W10B Maintenance, W10.1.3.4
W11A Maintenance, W11.0.2.2
#2: 3x2
for High power & High Capacity
Up to 3x2 Single band
in 2 Baseband pools
Issues
f1 f2to consider with this solution:
f1 f2
Advanced Configuration:
RBB22_1A for up to 3x2 Single Band
in 2 baseband pools
f1 f1
MIMO
f1 f1 MIMO
2nd DUW
B2, f1 Advanced Configuration:
f1 f1 for up to 3x1+3x1 Dual Band
MIMO in 2 baseband pools
RBB12_1A RBB12_1A
Issues to consider with this solution: Issues to consider with this solution:
f1 f2 f1 f2
• Multi-Carrier Dual Band supported • Multi-Carrier within band supported
• Multi-Carrier within band not supported • Multi-Carrier Dual Band not supported
• EUL in 2 BB pools supported in RBS 6000 • EUL in 2 BB pools supported in RBS 3000 & 6000
#3: DUAL band 3x2 + 3x2,
one RBS NODE - Multi CARRIER
Up to 3x2 + 3x2 Dual Band Issues to consider with this solution:
MIMO
with f1 f2
• Multi-Carrier within band not supported
Basic Configuration MIMO • Multi-Carrier Dual Band supported
f1 f1
f2 f2 • EUL in 2 BB pools supported in RBS 6000
1st DUW
B1, f1
B2, f1 f1 f1 MIMO
f2 f2
f1 f1
f2 f2
MIMO
f1 f1 MIMO
2nd DUW f2 f2
B1, f2
B2, f2 f1 f1
f2 f2 MIMO ¾ 12 RU/RRU Support in RBS 6000
from April 21, 2011 in
DBB21_01
f1 f1 W10B Maintenance, W10.1.3.4
f2 f2 W11A Maintenance, W11.0.2.2
RBB22_1A
¾ Dual Band Multi Carrier,
up to 3x2 + 3x2:
Support from W11B
one RBS NODE - Multi
CARRIER
Issues to consider with this solution:
Up to 3x2 + 3x2 Dual Band
• Multi Carrier Dual Band supported
with • Multi Carrier within Band not supported
Basic Configuration • EUL in 2 BB pools supported in RBS 6000
Freq Band 2
DualCarrier- DualCarrier- DualCarrier- DualCarrier- DualCarrier- DualCarrier-
Sector 1 Sector 2 Sector 3 Sector 4 Sector 3 Sector 4
First carriers, 3x2 to first BB-pool with MC Second carriers, 3x2 to second BB-pool with MC
Carrier 1 Carrier 1
Carrier 2 Carrier 2
Band 1, 3x2 to first BB-pool with MC Band 2, 3x2 to second BB-pool with MC
1 RF A
TX A / RX A
TX
1
TX
RF A
TX A / RX A
MC SB = f1+f2,f3+f4 Data 1 RF B
MC SB = f1+f3,f2+f4 Data 1 RF B
Data 2 RXA I/O RBB 11 1a
Data 2 RXA I/O 3x3/3x4 configured RXA Out
3x3/3x4 configured RX
RXA Out
RXB I/O
as Adv 6-sector
RX RXB I/O
Sector 1+4
as Normal 3-sector RBB 22 1a Sector 1
2 RF A
DUW 1 f1 B1 f2 B1 2
TX
RF A
RF B
TX B / RX B
DUW 1 f1 B1 f3 B1
Data 1
TX
TX B / RX B
Data 1 RF B
DUW 2 f3 B1 f4 B1 Data 2 RXA I/O
RBB 11 1a
DUW 2 f2 B1 f4 B1
RXA Out
Data 2 RXA I/O
RX RXB I/O
RXA Out
RX RXB I/O
DBB 2 1
Conf 01
DBB 2 1
f1 Conf 01
f1 S1 RI A
1 RF A
S1
S2
RI A
RI B
1
Data 1
TX
RF A
RF B
TX A / RX A
S2 RI B TX A / RX A S3 RI C
RBB 11 1a
f2
TX
RF B Data 2 RXA I/O
Data 1
- RI D
S3 RI C RXA Out
f3 - RI D
Data 2 RXA I/O
RXA Out
-
DU-DU
RI E RX RXB I/O
Sector 2+5
- RI E RX RXB I/O
RBS Node #1 RI F
S4 RI A
Data 1 RF B
S5 RI B
Data 2 RXA I/O
RXA Out
RBB 11 1a
Data 2 RXA I/O RX RXB I/O
f2
S5
S6
RI B
RI C
RX
RXA Out
RXB I/O f3 S6
-
-
RI C
RI D
RI E
- RI D
DU-DU RI F
f4
- RI E
1 RF A
TX A / RX A
f4
TX
DU-DU RI F Data 1 RF B
1 RF A
Data 1
TX
RF B
TX A / RX A
Data 2 RXA I/O
RXA Out
RBB 11 1a
Data 2 RXA I/O RX RXB I/O
RX
RXA Out
RXB I/O
Sector 3+6
2 RF A
2 RF A
TX B / RX B
Data 1
TX
RF B
Data 2 RXA I/O
RXA Out
RBB 11 1a
RX RXB I/O
Data 2 RXA I/O
RXA Out
RX RXB I/O
Data 1 RF B
RXA Out
RBB 22 1a
RX RXB I/O
1 RF A
TX A / RX A
TX
Data 1 RF B
RXA I/O
2 RF A
TX B / RX B
Data 2 TX
RX RXB I/O
MC SB = f1+f2 Data 2 RXA I/O
RXA Out
Sector 1+4
3x3 configured RX RXB I/O
MC SB = f1+f3 2
TX
RF A
TX B / RX B
Data 1 RF B
as Adv 6-sector
3x3 configured Data 2 RXA I/O
RBB 32 1a Sector 1
3
TX
RF A
TX C
RXA Out
DUW 1 f1 B1 f2 B1 Data 1 RF B
DUW 1 f1 B1 f3 B1 3 RF A
TX C
RX RXB I/O
TX
DUW 2 f2 B1 Data 1 RF B
RBB 22 1a
RX
Conf 01 1 RF A
TX A / RX A - RI D
TX
Data 1 RF B
S1 RI A - RI E 2 RF A
TX B / RX B
TX
RXA I/O
Data 2
DU-DU
S2
S3
RI B
RI C RX
RXA Out
RXB I/O
RBS Node #1 RI F Data 1
Data 2
RF B
-
S4 RI A
RI E 2 RF A
TX
TX B / RX B
S5 RI B
RBS Node #1 DU-DU RI F Data 1 RF B
S6 RI C 3 RF A
TX C
Data 2 RXA I/O
S4 RI A
RX RXB I/O
- RI E
Data 2 RXA I/O
RXA Out
RBB 10 1a
S5 RI B DU-DU RI F RX RXB I/O
S6 RI C 3 RF A
TX C
TX
Data 1 RF B
- RI D
Data 2 RXA I/O
- RI E
RXA Out 1 RF A
TX A / RX A
TX
DU-DU RI F RXB I/O
RX Data 1 RF B
RXA Out
1 RF A
TX A / RX A
RX RXB I/O
RBB 22 1a
TX
Data 1 RF B
2 RF A
TX B / RX B
TX
RX
RXA Out
RXB I/O
Data 2 RXA I/O Sector 3+6
RXA Out
RX RXB I/O
2 RF A
TX B / RX B
TX
Data 1 RF B
3 RF A
TX C
TX
Data 2 RXA I/O
RX
RXA Out
RXB I/O
Data 2 RXA I/O RBB 10 1a
RXA Out
RX RXB I/O
3 RF A
TX C
TX
Data 1 RF B
RXA Out
RX RXB I/O
¾ Flexible configuration candidate for W12B ¾ Support in RBS 6000 from June 1, 2011.
W11A Maintenance, W11.0.3.0
#6: 3x4 HP as 3x2+3x2
Translation Table 1
Data 1
TX
RF A
RF B
TX A / RX A
DB SB Data 2
RX
RXA I/O
RXA Out
RXB I/O
f1 B1 f1 B1 2
Data 1
TX
RF A
RF B
TX B / RX B RBB 22 1a
f2 B1 f2 B1 Data 2
RX
RXA I/O
RXA Out
RXB I/O
Sector 1+4
f1 B2 f3 B1 1
Data 1
TX
RF A
RF B
TX C / RX C
f2 B2 f4 B1 Data 2
RX
RXA I/O
RXA Out
RXB I/O
2 RF A
TX D / RX D
RBB 22 1a
TX
Data 1 RF B
RXA Out
RX RXB I/O
1 RF A
TX A / RX A
TX
Data 1 RF B
RX RXB I/O
S1 RI A
S2 RI B
S3 RI C 2
TX
RF A
TX B / RX B RBB 22 1a
Data 1 RF B
- RI D
Data 2 RXA I/O
- RI E
RXA Out
DU-DU
RBS Node #1 RI F RX RXB I/O
Sector 2+5
1 RF A
TX C / RX C
S4 RI A TX
Data 1 RF B
S5 RI B
RXA I/O
MC SB = Not OK MC SB = OK
Data 2
S6 RI C RXA Out
- RI D RX RXB I/O
MC DB = OK MC DB = not OK MC SB = not OK MC SB = OK -
DU-DU
RI E
RI F 2
TX
RF A
TX D / RX D
RBB 22 1a
Basic Advanced "3x4" based "3x4" based Data 1 RF B
RXA Out
DUW 1 f1 B1 f1 B2 f1 B1 f2 B1 f1 B1 f3 B1 f1 B1 f2 B1 1
TX
RF A
TX A / RX A
Data 1 RF B
RXA Out
RX RXB I/O
2
TX
RF A
TX B / RX B RBB 22 1a
Data 1 RF B
RXA Out
RX RXB I/O
Sector 3+6
1 RF A
TX C / RX C
TX
Data 1 RF B
RXA Out
RX RXB I/O
2 RF A
TX D / RX D
RBB 22 1a
TX
Data 1 RF B
RXA Out
RX RXB I/O