Professional Documents
Culture Documents
Additional actuator constructions that do not have FS 10. No dynamic instability due to negative gradients.
number designations can be selected by using a more
complicated and more exact force method found in
Section B of this catalog. These tables are arranged by unbalanced or balanced
valve construction and then by increasing port diameter
for each actuator type. (The trim parts in a balanced
These pressure drop tables provide sizing information for
design minimize the net fluid flow forces creating static
FS numbered actuators used on the general valve
unbalance, making possible the selection of a smaller
construction and application conditions described below.
actuator.)
(The Design GX control valve and actuator follow a
different actuator selection process than other Fisher
sliding-stem products. Please refer to the following The valve designs included in this section are listed in
section entitled, “Design GX”). the following table.
EFisher Controls International LLC 1987, 2003; All Rights Reserved Printed in USA
Actuator Sizing
For Sliding-Stem Valves
nP Method Catalog 14
December 2004 - Page A-2
4. The maximum allowable pressure drops are equal to an actuator construction that will allow the required
the maximum inlet pressure. The Catalog 14 allowable pressure drop. Proceed to larger actuator sizes or to a
pressure drops are the maximum pressure differentials greater air supply pressure as necessary.
at which the actuator can still close the valve and
provide seating load. 5. To order the actuator, specify the FS number printed in
the box for the actuator construction selected. (For Type
5. Unlike the easy-e, CP, and other sliding-stem valves, 585C [sizes 60 - 130] and the Design GX, these tables
the Design GX does not use the Group 1 actuator may be used as an actuator size selection guide. No FS
mounting. Instead, the GX uses a trapped bonnet that is numbers have been provided. Refer to Catalog 14,
clamped between the actuator and the valve body. The Section B for additional detail on the Type 585C.)
GX actuator is not used on any other sliding stem valve.
Balanced and Unbalanced Valves by Design Letter
Style Design Letter ANSI Shutoff Class
6. The required actuator air supply pressures are ED and EWD
Class II
indicated in the charts. For most constructions, the (ANSI Class 125 thru 2500)
Balanced
Design GX requires a minimum of 4 barg (58 psig) air ET and EWT Class IV—metal seats
supply, with a maximum allowable air supply of 6 barg (ANSI Class 125 thru 2500) Class V—PTFE seats
(87 psig). In the case of alloy constructions, the CP (only with System 9000)
D
maximum allowable air supply pressure to the actuator ES and EWS
Class IV
Unbalanced
has been limited in certain cases. When supplied with a EZ
3582i I/P positioner, maximum allowable air supply is CP (only with System 9000) Class VI
3.44 barg (50 psig); this may be further limited in the
case of alloy constructions.
Major topics covered in Section A are:
1. Locate the appropriate tables for the desired actuator Type 529 Spring-and-Diaphragm Actuator
type. The tables for a System 9000 actuator are Unbalanced Valve Bodies . . . . . . . . . . . . . . . . . A-3/A-4
appropriate for the valves shown in the tables. The Type 585C Piston Actuator
tables for all other actuator types are appropriate for the Unbalanced Valve Bodies . . . . . . . . . . . . . . . . . . . . A-5
balanced or unbalanced valve body designs listed Balanced Valve Bodies . . . . . . . . . . . . . . . . . . . . . . . A-7
above. Type 657 Spring-and-Diaphragm Actuator
Unbalanced Valve Bodies . . . . . . . . . . . . . . . . . . . A-11
Balanced Valve Bodies . . . . . . . . . . . . . . . . . . . . . . A-17
2. Enter the table for the given port diameter and travel. Type 667 Spring-and-Diaphragm Actuator
Unbalanced Valve Bodies . . . . . . . . . . . . . . . . . . . A-25
3. For all designs, find the yoke boss diameter that Balanced Valve Bodies . . . . . . . . . . . . . . . . . . . . . . A-31
matches the yoke boss on the given valve body. FloVuet System 9000 Actuator
Unbalanced Valves with Metal Seat . . . . . . . . . . . A-41
Unbalanced Valves with PTFE Seat . . . . . . . . . . . A-43
4. Begin with the smallest actuator size listed in the Balanced Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . A-45
actuator size column, and read from left to right to find Design GX Control Valve and Actuator . . . . . . . . . . A-49
Fisher is a mark owned by Fisher Controls International LLC, a member of the Emerson Process Manage-
ment business division of Emerson Electric Co. The Emerson logo is a trademark and service mark of Emer-
son Electric Co. All other marks are the property of their respective owners.
www.Fisher.com
EFisher Controls International LLC 1987, 2004; All Rights Reserved Printed in USA
Type 529
Unbalanced Valve Bodies
Class VI Shutoff (Fail Open or Fail Closed)
Design CP Valve
VALVE SIZE, YOKE BOSS PORT DIAMETER, FAIL CLOSED(1) FAIL OPEN(1)
ACTUATOR SIZE TRAVEL, INCHES
INCHES DIAMETER, INCHES INCHES nP, psi nP, psi
Air Diaphragm Pressure, psig " 5-15 3-13
1/2 3/8 569 750
10 1/2 1 1/8
1-1/8
3/4 9/16 158 416
1. Assumes 20 psi supply from positioner.
2-Inch Port
1-1/8 3-9/16 60 691 850 1168 1486
3- Inch Port
60 289 360 501 642
1-1/2 3-9/16
68 499 612 --- ---
4-Inch Port
60 152 192 271 357
1-1/2 3-9/16
68 270 334 --- ---
60 152 192 271 357
3-9/16
68 270 334 --- ---
2 80 (1) 268 332 458 585
5 100 (2) 417 511 697 884
130 (2) 743 902 --- ---
6-Inch Port
60 31 49 83 118
3-9/16
68 83 110 --- ---
2 80 (1) 82 110 165 220
5 100 (2) 147 188 269 351
130 (2) 289 358 --- ---
7-Inch Port
60 17 30 56 82
3-9/16
68 55 76 117 158
2 80 (1) 55 75 117 158
5 100 (2) 103 134 195 256
130 (2) 210 261 --- ---
8-Inch Port
60 8 18 38 57
3-9/16
68 37 53 --- ---
2 80 (1) 37 53 84 116
5 100 (2) 74 97 144 191
130 (2) 155 195 --- ---
1. 1-inch stem.
2. 1-1/4 inch stem.
Catalog 14
September 2000 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1992, 2000;
Page A-6 All Rights Reserved
Type 585C
Size 60-130
Balanced Valve Bodies
2-7/8—5-3/8-Inch Ports
4--3/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
2 3-9/16 60 1440 1440 1440 1440
Catalog 14
September 2000 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1992, 2000;
Page A-8 through A-10 All Rights Reserved
Type 657
Unbalanced Valve Bodies
Class IV Leakage
1/4—1/2 Inch Ports
3/8-Inch Port
485 2158 2995 485 2158 3831
30
(657-3) (657-50)(2) (657-51)(3) (657-83) (657-84) (657-85)
2 1/8
2-1/8
1113 3622 4876 1113 3622 6000
34
(657-7) (657-59)(2) (657-58)(3) (657-97) (657-98) (657-99)
999 3508 4763 999 3508 6000
40
(657-11) (657-100) (2) (657-101) (3) (657-102) (657-103) (657-104)
3/4 2 13/16
2-13/16
1981 4845 6000 1981 5799 6000
45
(657-16) (657-111) (657-112) (657-113) (657-114) (657-115)
1754 4617 6000 1754 5572 6000
50
(657-315) (657-316) (657-317) (657-318) (657-319) (657-320)
3 9/16
3-9/16
3145 6000 6000 3145 6000 6000
60
(657-321) (657-322) (657-323) (657-324) (657-325) (657-326)
1/2-Inch Port
192 1131 1600 192 1131 2070
30
(657-3) (657-50)(2) (657-51)(3) (657-83) (657-84) (657-85)
2 1/8
2-1/8
544 1952 2656 544 1952 3360
34
(657-7) (657-59)(2) (657-58)(3) (657-97) (657-98) (657-99)
480 1888 2592 480 1888 3297
40
(657-11) (657-100) (2) (657-101) (3) (657-102) (657-103) (657-104)
3/4 2 13/16
2-13/16
1031 2638 3710 1031 3174 5317
45
(657-16) (657-111) (657-112) (657-113) (657-114) (657-115)
904 2511 3582 904 3047 5189
50
(657-315) (657-316) (657-317) (657-318) (657-319) (657-320)
3 9/16
3-9/16
1684 4702 5664 1684 4868 6000
60
(657-321) (657-322) (657-323) (657-324) (657-325) (657-326)
1. The pressure drops shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal
signal. Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3 - 11 psig range.
3. 3 - 9 psig range.
1-Inch Port
--- 202 261 --- 202 437
30
--- (657-50)(2) (657-51)(3) --- (657-84) (657-85)
2 1/8
2-1/8
56 408 495 56 408 759
34
(657-7) (657-59)(2) (657-58)(3) (657-97) (657-98) (657-99)
40 392 479 40 392 743
40
(657-11) (657-100) (2) (657-101) (3) (657-102) (657-103) (657-104)
3/4 2 13/16
2-13/16
178 579 846 178 713 1248
45
(657-16) (657-111) (657-112) (657-113) (657-114) (657-115)
146 547 815 146 681 1216
50
(657-315) (657-316) (657-317) (657-318) (657-319) (657-320)
3 9/16
3-9/16
341 937 1334 341 1136 1930
60
(657-321) (657-322) (657-323) (657-324) (657-325) (657-326)
40 392 479 40 392 743
40
(657-12) (657-62) (657-63) (657-105) (657-106) (657-107)
1 1/8
1-1/8 2 13/16
2-13/16
178 579 846 178 713 1248
45
(657-17) (657-116) (657-69) (657-117) (657-118) (657-119)
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1978, 1998;
Page AĆ12 All Rights Reserved
Type 657
Unbalanced Valve Bodies
Class IV Leakage
1-5/16—1-7/8 Inch Ports
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ14 All Rights Reserved
Type 657
Unbalanced Valve Bodies
Class IV Leakage
3—4-Inch Ports
4-Inch Port
--- 4 20 --- 12 46
50
--- (657-124) (657-125) --- (657-127) (657-128)
--- 28 65 --- 41 90
1-1/2 3-9/16 60
--- (657-133) (657-134) (3) --- (657-136) (657-137)
6 59 --- 6 --- 146
70
(657-141) (657-142) --- (657-143) --- (657-145)
--- 6 31 --- 14 47
2-13/16 45
--- (657-279) (657-280) (3) --- (657-282) (657-283)
--- 4 29 --- 12 45
50
--- (657-73) (657-72)(3) --- (657-130) (657-131)
--- 40 65 --- 40 90
3-9/16 60
--- (657-75)(2) (657-74)(3) --- (657-139) (657-140)
2
6 --- 94 6 76 146
70
(657-146) --- (657-147) (657-148) (657-149) (657-150)
4 --- 92 4 74 144
87
(657-155) --- (657-156) (657-157) (657-158) (657-159)
5
19 --- 132 19 --- 200
80
(657-164) --- (657-165) (657-166) --- (657-167)
1. The pressure drops as shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig diaphragm loading for a 6 to
30 psig nominal signal. Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig.
3. 3-9 psig range.
6 Inch Port
––– ––– ––– ––– ––– 4
60
––– ––– ––– ––– ––– (657-140)
3-9/16
––– ––– 6 ––– ––– 29
70
––– ––– (657-147) ––– ––– (657-150)
2
––– ––– 5 ––– ––– 28
87
––– ––– (657-156) ––– ––– (657-159)
5
––– ––– 23 ––– ––– 52
80
––– ––– (657-165) ––– ––– (657-167)
7 Inch Port
––– ––– ––– ––– ––– 15
3-9/16 70
––– ––– ––– ––– ––– (657-149)
––– ––– ––– ––– ––– 14
2 87
––– ––– ––– ––– ––– (657-159)
5
––– ––– 10 ––– ––– 32
80
––– ––– (657-165) ––– ––– (657-167)
8 Inch Port
––– ––– ––– ––– ––– 6
3-9/16 70
––– ––– ––– ––– ––– (657-150)
––– ––– ––– ––– ––– 6
2 87
––– ––– ––– ––– ––– (657-159)
5
––– ––– 3 ––– ––– 20
80
––– ––– (657-165) ––– ––– (657-167)
1. The pressure drops shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig diaphragm loading for a 6 to 30
psig nominal signal. Any positioner, controller,, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig range.
3. 3-9 psig range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ16 All Rights Reserved
Type 657
Balanced Valve Bodies
1-5/16 Inch Ports
1-5/16 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 750 1184 ––– 750 1440
30
––– (657-50)(2) (657-51)(3) ––– (657-84) (657-85)
2 1/8
2-1/8
207 1440 1440 207 1440 1440
34
(657-7) (657-59)(2) (657-58)(3) (657-97) (657-98) (657-99)
3/4
––– 1440 1440 ––– 1440 1440
2-13/16 40
––– (657-100(2)) (657-101(3)) ––– (657-103) (657-104)
542 1440 1440 542 1440 1440
3-9/16 50
(657-315) (657-316) (657-317) (657-318) (657-319) (657-320)
1. The pressure drops shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig diaphragm loading for a 6 to 30
psig nominal signal. Any positioner, controller,, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig range.
3. 3-9 psig range.
1-7/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
--- 361 673 --- 361 986
30
--- (657-50)(2) (657-51)(3) --- (657-84) (657-85)
2 1/8
2-1/8
--- 908 1378 --- 908 1440
34
--- (657-59)(2) (657-58)(3) --- (657-98) (657-99)
--- 867 1337 --- 867 1440
3/4 40
--- (657-100) (2) (657-101) (3) --- (657-103) (657-104)
2 13/16
2-13/16
296 1367 1440 296 1440 1440
45
(657-16) (657-111) (657-112) (657-113) (657-114) (657-115)
211 1282 1440 211 1440 1440
3-9/16 50
(657-315) (657-316) (657-317) (657-318) (657-319) (657-320)
1. The pressure drops as shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig diaphragm loading for a 6 to
30 psig nominal signal. Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig.
3. 3-9 psig range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ18 All Rights Reserved
Type 657
Balanced Valve Bodies
2-5/16—2-7/8 Inch Ports
2-5/16 Inch Port (Design ET, Class V Leakage) Soft Seat Only
--- 402 784 --- 593 1548
40
--- (657-62) (657-63) --- (657-106) (657-107) (4)
1 1/8
1-1/8 2 13/16
2-13/16
127 1000 1440 127 1291 1440
45
(657-17) (657-116) (657-69) (657-117) (657-118) (657-119)
2-7/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
--- 355 659 --- 355 ---
40
--- (657-66)(2) (657-67)(3) --- (657-109) ---
2 13/16
2-13/16
--- 678 1141 --- 910 1440
45
--- (657-70) (657-71) --- (657-121) (657-122)
1 1/2
1-1/2
--- 623 1086 --- 855 1440
50
--- (657-124) (657-125) --- (657-127) (657-128)
3 9/16
3-9/16
267 1297 1440 267 1440 1440
60
(657-132) (657-133) (657-134) (3) (657-135) (657-136) (657-137)
1. The pressure drops as shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig diaphragm loading for a 6 to
30 psig nominal signal. Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig.
3. 3-9 psig range.
4. 6-21 psig range.
3-7/16 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 201 459 ––– 201 –––
40
––– (657-66)(2) (657-67))3) ––– (657-109) –––
2 13/16
2-13/16
––– 475 868 ––– 672 1440
45
––– (657-70) (657-71) ––– (657-121) (657-122)
1 1/2
1-1/2
––– 429 821 ––– 625 1408
50
––– (657-124) (657-125) ––– (657-127) (657-128)
3 9/16
3-9/16
127 1000 1440 127 1291 1440
60
(657-132) (657-133) (657-134) )3) (657-135) (657-136) (657-137)
1. The pressure drops shown assume a supply pressure to the actuator of 0 to 18 psig for a 3 to 15 nominal psig signal and a 0 to 33 psig supply for a 6 to 30 nominal psig signal. A
positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig range.
3. 3-9 psig range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ20 All Rights Reserved
Type 657
Balanced Valve Bodies
4-3/8 Inch Ports
4-3/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 243 705 ––– 397 1013
2-13/16 45
––– (657-279) (657-280) (3) ––– (657-282) (657-283)
––– 207 669 ––– 361 977
50
––– (657-73) (657-72)(3) ––– (657-130) (657-131)
––– 884 1342 ––– 884 1799
2 3-9/16 60
––– (657-75)(2) (657-74)(3) ––– (657-139) (657-140)
251 ––– 1440 251 1440 1440
70
(657-146) ––– (657-147) (657-148) (657-149) (657-150)
214 ––– 1440 214 1440 1440
5 87
(657-155) ––– (657-156) (657-157) (657-158) (657-159)
1. The pressure drops shown assume a supply pressure to the actuator of 0 to 18 psig for a 3 to 15 nominal psig signal and a 0 to 33 psig supply for a 6 to 30 nominal psig signal. A
positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig range.
3. 3-9 psig range.
5-3/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 56 430 ––– 180 679
50
––– (657-73) (657-72)(3) ––– (657-130) (657-131)
––– 605 975 ––– 604 1345
3-9/16 60
––– (657-75)(2) (657-74)(3) ––– (657-139) (657-140)
91 ––– 1398 91 1136 1440
2 70
(657-146) ––– (657-147) (657-148) (657-149) (657-150)
62 ––– 1368 62 1106 1440
87
(657-155) ––– (657-156) (657-157) (657-158) (657-159)
5
382 ––– 1440 382 ––– 1440
80
(657-164) ––– (657-165) (657-166) ––– (657-167)
91 ––– ––– 91 ––– 1440
3-9/16 70
(657-151) ––– ––– (657-153) ––– (657-154)
62 ––– ––– 62 ––– 1440
3 87
(657-160) ––– ––– (657-162) ––– (657-163)
5
382 ––– ––– 382 1440 –––
80
(657-168) ––– ––– (657-169) (657-170) –––
1. The pressure drops shown assume a supply pressure to the actuator of 0 to 18 psig for a 3 to 15 nominal psig signal and a 0 to 33 psig supply for a 6 to 30 nominal psig signal. A
positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 3-11 psig range.
3. 3-9 psig range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ22 All Rights Reserved
Type 657
Balanced Valve Bodies
7 Inch Ports
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1991, 1998;
Page AĆ24 All Rights Reserved
Type 667
Unbalanced Valve Bodies
Class IV Leakage
Catalog 14
September 2002 - Page A-25 1/4—1/2 Inch Ports
EFisher Controls International, Inc. 1991, 2002; All Rights Reserved Printed in USA
Type 667
Unbalanced Valve Bodies
Class IV Leakage Catalog 14
3/4—1-1/4 Inch Ports June 1998 - Page A-26
1-Inch Port
-- -- -- 202 319 143 378 612
30
-- -- -- (667-31)(2) (667-85)(3) (667-86) (667-87) (667-88)
2 1/8
2-1/8
56 407 583 319 671 1022
34
(667-7) (667-33)(2) (667-100)(3) (667-101) (667-102) (667-103)
40 391 567 303 655 1006
40
(667-10) (667-104)(2) (667-105)(3) (667-106) (667-107) (667-108)
3/4 2 13/16
2-13/16
177 578 846 578 1113 1649
45
(667-15) (667-66) (667-119) (667-120) (667-121) (667-122)
145 547 814 547 1082 1617
50
(667-197) (667-198) (667-199) (667-200) (667-201) (667-202)
3 9/16
3-9/16
340 936 1334 936 1731 2526
60
(667-203) (667-204) (667-205) (667-206) (667-207) (667-208)
40 303 479 303 671 -- -- --
40
(667-11) (667-35) (667-61) (667-111) (667-112) -- -- --
1 1/8
1-1/8 2 13/16
2-13/16
177 578 846 578 1113 1649
45
(667-18) (667-67) (667-124) (667-125) (667-126) (667-127)
Fisher is a mark owned by Fisher Controls International, Inc., a business of Emerson Process Management.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
All other marks are the property of their respective owners.
www.Fisher.com
EFisher Controls International, Inc. 1990, 2002; All Rights Reserved Printed in USA
Type 667
Unbalanced Valve Bodies
Class IV Leakage
1-5/16—1-1/2 Inch Ports
2-Inch Port
––– 10 40 ––– 54 113
30
––– (667-31)(2) (667-85)(3) ––– (667-87) (667-88)
2 1/8
2-1/8
––– 61 105 40 127 215
34
––– (667-33)(2) (667-100) (3) (667-101) (667-102) (667-103)
––– 58 101 36 123 211
40
––– (667-104) (2) (667-105) (3) (667-106) (667-107) (667-108)
3/4 2 13/16
2-13/16
4 104 171 104 238 372
45
(667-15) (667-66) (667-119) (667-120) (667-121) (667-122)
––– 96 163 96 230 364
50
––– (667-198) (667-199) (667-200) (667-201) (667-202)
3 9/16
3-9/16
45 194 293 194 393 591
60
(667-203) (667-204) (667-205) (667-206) (667-207) (667-208)
––– 36 79 36 123 –––
40
––– (667-35) (667-61) (667-111) (667-112) –––
1 1/8
1-1/8 2 13/16
2-13/16
4 104 171 104 238 372
45
(667-18) (667-67) (667-124) (667-125) (667-126) (667-127)
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ28 All Rights Reserved
Type 667
Unbalanced Valve Bodies
Class IV Leakage
2-7/8—4 Inch Ports
3-Inch Port
––– 7 ––– ––– ––– –––
40
––– (667-64)(2) ––– ––– ––– –––
2 13/16
2-13/16
––– 28 58 28 88 147
45
––– (667-37) (667-129) (667-36) (667-131) (667-132)
––– 25 54 25 84 144
1-1/2 50
––– (667-133) (667-134) (667-135) (667-136) (667-137)
2 68 ––– 68 156 –––
3-9/16 60
(667-143) (667-144) ––– (667-146) (667-147) –––
29 122 ––– 122 ––– 371
70
(667-152) (667-153) ––– (667-154) ––– (667-156)
4-Inch Port
––– 4 20 4 37 71
50
––– (667-133) (667-134) (667-135) (667-136) (667-137)
––– 28 ––– 28 78 –––
1-1/2 3-9/16 60
––– (667-144) ––– (667-146) (667-147) –––
6 59 ––– 59 ––– 199
70
(667-152) (667-153) ––– (667-154) ––– (667-156)
––– 6 ––– 6 39 –––
2-13/16 45
––– (667-182) ––– (667-183) (667-184) –––
––– 4 ––– 4 37 –––
50
––– (667-70) ––– (667-140) (667-141) –––
3 9/16
3-9/16
6 ––– 94 59 129 199
2 70
(667-157) ––– (667-158) (667-159) (667-160) (667-161)
4 ––– 92 57 127 197
87
(667-166) ––– (667-167) (667-168) (667-169) (667-170)
5
19 ––– 132 87 ––– 268
80
(667-175) ––– (667-176) (667-177) ––– (667-178)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 7–15 psig range.
6-Inch Port
––– ––– 6 ––– 21 52
3-9/16 70
––– ––– (667-158) ––– (667-160) (667-161)
––– ––– 5 ––– 20 51
2 87
––– ––– (667-167) ––– (667-169) (667-170)
5
––– ––– 23 3 ––– 82
80
––– ––– (667-176) (667-177) ––– (667-178)
7-Inch Port
––– ––– ––– ––– 9 32
3-9/16 70
––– ––– ––– ––– (667-160) (667-161)
––– ––– ––– ––– 8 31
2 87
––– ––– ––– ––– (667-169) (667-170)
5
––– ––– 10 ––– ––– 55
80
––– ––– (667-176) ––– ––– (667-178)
8-Inch Port
––– ––– ––– ––– 2 19
3-9/16 70
––– ––– ––– ––– (667-160) (667-161)
––– ––– ––– ––– 1 19
2 87
––– ––– ––– ––– (667-169) (667-170)
5
––– ––– 3 ––– ––– 37
80
––– ––– (667-176) ––– ––– (667-178)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ30 All Rights Reserved
Type 667
Balanced Valve Bodies
1-5/16 Inch Ports
1-5/16 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 750 1184 533 1401 1440
30
––– (667-31)(2) (667-85)(3) (667-86) (667-87) (667-88)
2 1/8
2-1/8
207 1440 1440 1184 1440 1440
34
(667-7) (667-33)(2) (667-100) (3) (667-101) (667-102) (667-103)
3/4
151 1440 1440 1127 1440 1440
2-13/16 40
(667-10) (667-104) (2) (667-105) (3) (667-106) (667-107) (667-108)
542 1440 1440 1440 1440 1440
3-9/16 50
(667-197) (667-198) (667-199) (667-200) (667-201) (667-202)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 7-15 psig range.
3. 9-15 psig range.
1-7/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
--- 360 673 204 830 1440
30
--- (667-31)(2) (667-85)(3) (667-86) (667-87) (667-88)
2 1/8
2-1/8
--- 908 1377 673 1440 1440
34
--- (667-33)(2) (667-100) (3) (667-101) (667-102) (667-103)
--- 867 1337 633 1440 1440
3/4 40
--- (667-104) (2) (667-105) (3) (667-106) (667-107) (667-108)
2 13/16
2-13/16
295 1367 1440 1367 1440 1440
45
(667-15) (667-66) (667-119) (667-120) (667-121) (667-122)
211 1282 1440 1282 1440 1440
3-9/16 50
(667-197) (667-198) (667-199) (667-200) (667-201) (667-202)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate extended range.
2. 7-15 psig range.
3. 9-15 psig range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ32 All Rights Reserved
Type 667
Balanced Valve Bodies
2-5/16—2-7/8 Inch Ports
2-5/16 Inch Port (Design ET, Class V Leakage) Soft Seal Only
--- 402 784 402 1166 ---
40
--- (667-35) (667-61) (667-111) (667-112) ---
1 1/8
1-1/8 2 13/16
2-13/16
127 1000 1440 1000 1440 1440
45
(667-18) (667-67) (667-124) (667-125) (667-126) (667-127)
2-7/8 Inch Port (Design ET, Class V Leakage) Soft Seal Only
--- 355 --- 202 --- ---
40
--- (667-64)(2) --- (667-115) --- ---
2 13/16
2-13/16
--- 678 1141 678 1440 1440
45
--- (667-37) (667-129) (667-36) (667-131) (667-132)
--- 623 1086 623 1440 1440
1-1/2 50
--- (667-133) (667-134) (667-135) (667-136) (667-137)
266 1297 --- 1297 1440 ---
3-9/16 60
(667-143) (667-144) --- (667-146) (667-147) ---
689 1440 --- 1440 --- 1440
70
(667-152) (667-153) --- (667-154) --- (667-156)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate extended range.
2. 7-15 psig range.
3. 9-15 psig range.
Fisher, Fisher-Rosemount, and Managing The Process Better are marks
owned by Fisher Controls International, Inc. or Fisher-Rosemount Sys-
tems, Inc. All other marks are the property of their respective owners. Catalog 14
Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
June 1998
All Rights Reserved Page AĆ33
Type 667
Balanced Valve Bodies
3-7/16 Inch Ports
3-7/16 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 201 ––– 72 ––– –––
40
––– (667-64)(2) ––– (667-115) ––– –––
2 13/16
2-13/16
––– 475 868 475 1259 1440
45
––– (667-37) (667-129) (667-36) (667-131) (667-132)
––– 429 821 429 1213 1440
1-1/2 50
––– (667-133) (667-134) (667-135) (667-136) (667-137)
127 1000 ––– 1000 1440 –––
3-9/16 60
(667-143) (667-144) ––– (667-146) (667-147) –––
485 1440 ––– 1440 ––– 1440
70
(667-152) (667-153) ––– (667-)154 ––– (667-156)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
2. 7-15 psig range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1990, 1998;
Page AĆ34 All Rights Reserved
Type 667
Balanced Valve Bodies
4-3/8 Inch Ports
4-3/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
––– 243 ––– 243 859 –––
2-13/16 45
––– (667-182) ––– (667-183) (667-184) –––
––– 207 ––– 207 823 –––
50
––– (667-70) ––– (667-140) (667-141) –––
––– ––– ––– 655 ––– –––
2 3-9/16 60
––– ––– ––– (667-151) ––– –––
250 ––– 1440 1218 1440 1440
70
(667-157) ––– (667-158) (667-159) (667-160) (667-161)
214 ––– 1440 1182 1440 1440
5 87
(667-166) ––– (667-167) (667-168) (667-169) (667-170)
1. The pressure drops shown assume a diaphragm pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal signal.
Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
5-3/8 Inch Port (Design ET, Class V Leakage) Soft Seat Only
--- 56 --- 56 555 ---
50
--- (667-70) --- (667-140) (667-141) ---
--- --- --- 419 --- ---
3-9/16 60
--- --- --- (667-151) --- ---
91 --- 1398 875 1440 1440
2 70
(667-157) --- (667-158) (667-159) (667-160) (667-161)
62 --- 1368 845 1440 1440
87
(667-166) --- (667-167) (667-168) (667-169) (667-170)
5
382 --- 1440 1440 --- 1440
80
(667-175) --- (667-176) (667-177) --- (667-178)
91 --- --- 875 --- ---
3-9/16 70
(667-162) --- --- (667-164) --- ---
62 --- --- 845 --- ---
3 87
(667-171) --- --- (667-173) --- ---
5
382 --- --- 1440 --- ---
80
(667-179) --- --- (667-180) --- ---
1. The pressure drops shown assume a diaphragm loading pressure to the actuator of 0 to 18 psig for a 3 to 15 psig nominal signal and a 0 to 33 psig supply for a 6 to 30 psig nominal
signal. Any positioner, controller, or transducer used with these actuators must be capable of delivering the appropriate slightly extended range.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1991, 1998;
Page AĆ36 All Rights Reserved
Type 667
Balanced Valve Bodies
Catalog 14 7 Inch Ports
June 1988 - Page A-37
EFisher Controls International LLC 1991, 1998; All Rights Reserved Printed in USA
Type 667
Balanced Valve Bodies
8-Inch Ports Catalog 14
December 2004 - Page A-38 through A-40
Fisher is a mark owned by Fisher Controls International LLC, a member of the Emerson Process Manage-
ment business division of Emerson Electric Co. The Emerson logo is a trademark and service mark of Emer-
son Electric Co. All other marks are the property of their respective owners.
www.Fisher.com
EFisher Controls International LLC 1978, 2004; All Rights Reserved Printed in USA
FloVuet System 9000
Unbalanced Valves with Metal Seat
Class IV Shutoff (Fail Open or Fail Closed)(1)
Design CP Valve
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
PORT (FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
VALVE SIZE, TRAVEL,
DIAMETER
DIAMETER,
INCHES INCHES Yoke Boss Size, Actuator
INCHES nP, psi nP, psi nP, psi nP, psi
Inches Size
20 --- 750 750 750
1/4 1, 1-1/2 3/4 2-1/8
25 750 750 750 750
1/2 1/2 1-1/8 12 --- 750 750 750
3/8 20 --- 750 750 750
1, 1-1/2
25 750 750 750 750
3/4 2 1/8
2-1/8
20 --- 750 750 750
1/2 1, 1-1/2
25 750 750 750 750
9/16 3/4 1/2 1-1/8 12 --- 620 750 750
20 --- 260 590 750
1, 1-1/2
25 680 750 750 750
3/4
20 --- 215 545 750
2
25 635 750 750 750
2 1/8
2-1/8
20 --- 65 215 360
1-1/2
3/4 25 255 750 750 750
1-1/8 20 --- 45 195 340
2
25 235 740 750 750
3 2-13/16 50 --- 275 565 750
20 --- --- 80 165
2 2-1/8
25 105 390 665 750
1 1/2
1-1/2
50 --- 110 275 435
4 1-1/8
80 160 385 685 985
50 --- 65 170 270
1-7/8 3
80 95 240 430 625
2-13/16 50 --- 20 80 135
3 1-1/2
80 35 120 225 335
2 1/2
2-1/2
50 --- 10 70 130
4
80 30 110 220 325
3-1/4 4 2 80 --- 55 120 180
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
Design ES or EZ Valve
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
PORT (FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL,
TRAVEL
DIAMETER, Yoke Boss
INCHES
INCHES Size, Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
20 --- 1500 1500 1500
3/4 2-1/8
25 1500 1500 1500 1500
1/4
50 --- 1500 1500 1500
1-1/8 2-13/16
80 1500 1500 1500 1500
20 --- 1500 1500 1500
3/4 2-1/8
25 1500 1500 1500 1500
3/8
50 --- 1500 1500 1500
1-1/8 2-13/16
80 1500 1500 1500 1500
20 --- 935 1500 1500
3/4 2-1/8
25 1500 1500 1500 1500
1/2
50 --- 1500 1500 1500
1-1/8 2-13/16
80 1500 1500 1500 1500
20 --- 345 670 1000
3/4 2-1/8
25 765 1500 1500 1500
3/4
50 --- 950 1500 1500
1-1/8 2-13/16
80 1155 1500 1500 1500
20 --- 150 335 520
3/4 2-1/8
25 390 1030 1500 1500
1
50 --- 495 865 1225
1-1/8 2-13/16
80 610 1120 1500 1500
20 --- 60 165 275
2-1/8
1-5/16
1 5/16 3/4 25 195 570 910 1215
2-13/16 50 --- 255 470 680
20 --- 30 115 195
1-1/2 3/4 2-1/8
25 135 420 695 930
20 --- --- 55 105
2-1/8
1-7/8
1 7/8 3/4 25 70 250 430 595
2-13/16 50 --- 100 205 305
50 --- 80 175 265
1-1/8
80 110 240 405 575
2 2-13/16 50 --- 80 175 265
1-1/2
80 110 240 405 575
2 80 110 240 405 575
50 --- 50 120 190
2-5/16 1-1/8 2-13/16
80 75 170 295 420
50 --- 20 65 110
2-7/8 1-1/2 2-13/16
80 35 95 180 260
50 --- 20 60 100
3 1-1/2 2-13/16
80 30 85 160 235
50 --- --- 40 70
3-7/16 1-1/2 2-13/16
80 15 60 115 175
4 2 2-13/16 80 --- 40 80 120
4-3/8 2 2-13/16 80 --- 30 65 100
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1996, 1998;
Page AĆ42 All Rights Reserved
FloVuet System 9000
Unbalanced Valves with PTFE Seat
Class VI Shutoff (Fail Open or Fail Closed)(1)
Design CP Valve
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
PORT (FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
VALVE SIZE, TRAVEL,
DIAMETER
DIAMETER,
INCHES INCHES Yoke Boss Size, Actuator
INCHES nP, psi nP, psi nP, psi nP, psi
Inches Size
20 --- 750 750 750
1/4 1
25 750 750 750 750
20 --- 750 750 750
3/8 1
25 750 750 750 750
20 --- 750 750 750
1/2 1, 1-1/2
25 750 750 750 750
20 --- 260 590 750
1, 1-1/2 2-1/8
25 680 750 750 750
3/4
3/4 20 --- 215 545 750
2
25 635 750 750 750
20 --- 65 215 360
1-1/2
25 255 750 750 750
1-1/8 20 --- 45 195 340
2
25 235 740 750 750
3 2-13/16 50 --- 275 565 750
20 --- 25 105 185
2 2-1/8
25 125 405 670 750
1 1/2
1-1/2
50 --- 130 290 445
4 1-1/8
80 180 400 685 750
50 --- 80 185 285
1-7/8 3
80 115 255 440 625
2-13/16 50 --- 35 90 150
3 1-1/2
80 50 130 235 345
2 1/2
2-1/2
50 --- 30 85 145
4
80 45 125 230 335
3-1/4 4 2 80 20 65 130 190
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
Design ES or EZ Valve
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
PORT (FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL,
TRAVEL
DIAMETER, Yoke Boss
INCHES
INCHES Size, Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
20 --- 1500 1500 1500
3/4 2-1/8
25 1500 1500 1500 1500
1/4
50 --- 1500 1500 1500
1-1/8 2-13/16
80 1500 1500 1500 1500
20 --- 1500 1500 1500
3/4 2-1/8
25 1500 1500 1500 1500
3/8
50 --- 1500 1500 1500
1-1/8 2-13/16
80 1500 1500 1500 1500
20 --- 935 1500 1500
3/4 2-1/8
25 1500 1500 1500 1500
1/2
50 --- 1500 1500 1500
1-1/8 2-13/16
80 1500 1500 1500 1500
20 --- 345 670 1000
3/4 2-1/8
25 765 1500 1500 1500
3/4
50 --- 950 1500 1500
1-1/8 2-13/16
80 1155 1500 1500 1500
20 --- 150 335 520
3/4 2-1/8
25 390 1030 1500 1500
1
50 --- 495 865 1225
1-1/8 2-13/16
80 610 1120 1500 1500
20 --- 85 190 290
2-1/8
1-5/16
1 5/16 3/4 25 215 575 910 1215
2-13/16 50 --- 275 480 685
20 --- 55 135 215
1-1/2 3/4 2-1/8
25 155 435 695 930
20 --- 20 75 125
2-1/8
1-7/8
1 7/8 3/4 25 90 265 440 595
2-13/16 50 --- 115 220 320
50 --- 100 190 280
1-1/8
80 125 250 415 580
2 2-13/16 50 --- 100 190 280
1-1/2
80 125 250 415 580
2 80 125 250 415 580
50 --- 65 135 200
2-5/16 1-1/8 2-13/16
80 90 180 305 425
50 --- 35 80 120
2-7/8 1-1/2 2-13/16
80 50 110 190 270
50 --- 30 70 110
3 1-1/2 2-13/16
80 45 100 170 245
50 --- 20 50 80
3-7/16 1-1/2 2-13/16
80 30 70 125 180
4 2 2-13/16 80 15 45 90 130
4-3/8 2 2-13/16 80 10 35 70 105
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1996, 1998;
Page AĆ44 All Rights Reserved
FloVuet System 9000
Balanced Valves
Fail Open or Fail Closed(1)
1–5/16 Inch Port (Design ET, Class V Shutoff) Soft Seat Only
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
(FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL
Yoke Boss Size,
Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
20 --- 575 1255 1500
2-1/8
3/4 25 1445 1500 1500 1500
2-13/16 50 --- 1500 1500 1500
1–7/8 Inch Port (Design ET, Class V Shutoff) Soft Seat Only
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
(FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL
Yoke Boss Size,
Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
20 --- 235 725 1220
2-1/8
3/4 25 860 1500 1500 1500
2-13/16 50 --- 1145 1500 1500
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
2–5/16 Inch Port (Design ET, Class V Shutoff) Soft Seat Only
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
(FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL
Yoke Boss Size,
Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
50 --- 820 1500 1500
1-1/8 2-13/16
80 1065 1500 1500 1500
2–7/8 Inch Port (Design ET, Class V Shutoff) Soft Seat Only
AIR SUPPLY PRESSURE, PSIG 25 40 60 80
(FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL
Yoke Boss Size,
Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
50 --- 535 1170 1500
1-1/2 2-13/16
80 730 1500 1500 1500
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
Catalog 14
June 1998 Printed in U.S.A. on recycled paper.
©Fisher Controls International, Inc., 1996, 1998;
Page AĆ46 All Rights Reserved
FloVuet System 9000
Balanced Valves
Fail Open or Fail Closed(1)
3-- 7/16 Inch Port (Design ET, Class V Shutoff) Soft Seat Only
AIR SUPPLY PRESSURE, PSIG 40 60 80
25
(FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL
Yoke Boss Size,
Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
50 --- 350 895 1425
1-1/2 2-13/16
80 520 1265 1500 1500
4-- 3/8 Inch Port (Design ET, Class V Shutoff) Soft Seat Only
AIR SUPPLY PRESSURE, PSIG 40 60 80
25
(FS NUMBER) (9000-BB4) (9000-BB6) (9000-BB8)
TRAVEL
Yoke Boss Size,
Actuator Size nP, psi nP, psi nP, psi nP, psi
Inches
2 2-13/16 80 280 865 1500 1500
1. Base FS Number is for Fail Open configuration. Fail Closed configuration requires an option number added to the FS Number.
The Design GX control valve and actuator system require no actuator sizing - there is only one actuator possibility for each
valve size and port diameter. See the section entitled “Design GX” on page A-1 of this catalog for further information.
Table 1. Maximum Allowable Valve Pressure Drops (1.6019/WCC and 1.4409/CF3M with PTFE or Graphite ULF Packing)
MAXIMUM PORT SUPPLY PRESSURE OF 4 BARG (58 PSIG)(5)
VALVE SIZE ACTUATOR
TRAVEL DIAMETER Air-to-Open Air-to-Close
SIZE
DN Inches mm mm Bar psi Bar psi
9.5 225 51.7 750 51.7 750
25 1 20 14 225 51.7 750 51.7 750
22 225 51.7 750 51.7 750
14 225 51.7 750 51.7 750
40 1-1/2 20 22 225 51.7 750 51.7 750
36 750(3) 51.7 750 51.7 750
22 225 51.7 750 51.7 750
50 2 20 36 750(3) 51.7 750 51.7 750
46 750(3) 51.7 750 51.7 750
36 750 51.7 750 51.7 750
20 46 750 50.6 734 51.7 750
80 3 70(1) 750 51.7 750 51.7 750
40 70 1200(4) 36.2 525 42.6 618
20 46 750 51.7 750 51.7 750
40 70 1200(4) 36.2 525 42.6 618
100 4 90(2) 750 51.7 750 51.7 750
20
90(1) 750 51.7 750 51.7 750
40 90 1200(4) 21.9 318 25.8 374
1. Balanced trim design.
2. Balanced trim with restricted capacity plug.
3. Supply pressure limited to 4 to 4.8 barg (58 to 70 psig) for air-to-close (spring-to-open) actuator action.
4. Supply pressure limited to 4 to 5.6 barg (58 to 81 psig) for air-to-close (spring-to-open) actuator action.
5. Maximum supply pressure of 6.0 barg (87 psig) unless otherwise noted.
Table 2. Maximum Allowable Valve Pressure Drops (Alloy Constructions with PTFE Packing)
SUPPLY PRESSURE OF 4 BARG (58 PSIG) UNLESS
MAXIMUM PORT OTHERWISE NOTED(6)
VALVE SIZE ACTUATOR
TRAVEL DIAMETER
SIZE Air-to-Open Air-to-Close
DN Inches mm mm Bar psi Bar psi
9.5 225 51.7 750 51.7 750
25 1 20 14 225 51.7 750 51.7 750
22 225 51.7 750 51.7 750
14 225 51.7 750 51.7 750
40 1-1/2 20 22 225 51.7 750 51.7 750
36 750(3) 32.3 468 51.7 750
22 225 51.7 750 51.7 750
50 2 20 36 750(3) 32.3 468 51.7 750
46 750(3) 19.8 287 40.8 592
36 750(5) 29.4 426 51.7 750
20 46 750(5) 18.0 261 40.8 592
80 3 70(1) 750(5) 51.7 750 51.7 750
40 70 1200(4) 19.1 277 41.5 602
20 46 750(5) 18.0 261 40.8 592
40 70 1200(4) 19.1 277 41.5 602
100 4 90(2) 750(5) 51.7 750 51.7 750
20
90(1) 750(5) 51.7 750 51.7 750
40 90 1200(4) 11.6 168 25.1 364
1. Balanced trim design.
2. Balanced trim with restricted capacity plug.
3. Supply pressure limited to 1.5 to 2 barg (22 to 29 psig) for air-to-close (spring-to-open) actuator action.
4. Supply pressure limited to 2.1 to 2.8 barg (30 to 40 psig) for air-to-close (spring-to-open) actuator action.
5. Supply pressure limited to 1.5 to 3.2 barg (22 to 46 psig) for air-to-close (spring-to-open) actuator action.
6. Maximum supply pressure of 6.0 barg (87 psig) unless otherwise noted.
EFisher Controls International LLC 2003; All Rights Reserved Printed in USA
Design GX
PN 10 - 40 (Classes 150 and 300)
Equal Percentage and Linear Cages Catalog 14
Flow Up through the Port October 2003 - Page A-50
The Design GX control valve and actuator system require no actuator sizing - there is only one actuator possibility for each
valve size and port diameter. See the section entitled “Design GX” on page A-1 of this catalog for further information.
Table 3. Maximum Allowable Valve Pressure Drops When Using the Type 3582i I/P Positioner (1.6019/WCC and 1.4409/CF3M with
PTFE or Graphite ULF Packing)
MAXIMUM PORT SUPPLY PRESSURE OF 3.44 BARG (50 PSIG)(3)
VALVE SIZE ACTUATOR
TRAVEL DIAMETER Air-to-Open Air-to-Close
SIZE
DN Inches mm mm Bar psi Bar psi
9.5 225 51.7 750 51.7 750
25 1 20 14 225 51.7 750 51.7 750
22 225 51.7 750 30.9 448
14 225 51.7 750 51.7 750
40 1-1/2 20 22 225 51.7 750 30.9 448
36 750 51.7 750 51.7 750
22 225 51.7 750 30.9 448
50 2 20 36 750 51.7 750 51.7 750
46 750 51.7 750 35.9 521
36 750 51.7 750 51.7 750
20 46 750 50.6 734 34.8 505
80 3 70(1) 750 51.7 750 25.4 368
40 70 1200 36.2 525 42.6 618
20 46 750 51.7 750 34.8 505
40 70 1200 36.2 525 25.4 368
100 4 90(2) 750 51.7 750 51.7 750
20
90(1) 750 51.7 750 51.7 750
40 90 1200 21.9 318 15.4 223
1. Balanced trim design.
2. Balanced trim with restricted capacity plug.
3. Maximum supply pressure of 3.44 barg (50 psig).
Table 4. Maximum Allowable Valve Pressure Drops When Using the Type 3582i I/P Positioner (Alloy Constructions with PTFE
Packing)
SUPPLY PRESSURE OF 3.44 BARG (50 PSIG) UNLESS
MAXIMUM PORT OTHERWISE NOTED(6)
VALVE SIZE ACTUATOR
TRAVEL DIAMETER
SIZE Air-to-Open Air-to-Close
DN Inches mm mm Bar psi Bar psi
9.5 225 51.7 750 51.7 750
25 1 20 14 225 51.7 750 51.7 750
22 225 51.7 750 39.7 576
14 225 51.7 750 51.7 750
40 1-1/2 20 22 225 51.7 750 39.7 576
36 750(3) 32.3 468 51.7 750
22 225 51.7 750 39.7 576
50 2 20 36 750(3) 32.3 468 51.7 750
46 750(3) 19.8 287 40.8 592
36 750(5) 29.4 426 51.7 750
20 46 750(5) 18.0 261 51.7 750
80 3 70(1) 750(5) 51.7 750 51.7 750
40 70 1200(4) 19.1 277 41.5 602
20 46 750(5) 18.0 261 51.7 750
40 70 1200(4) 19.1 277 41.5 602
100 4 90(2) 750(5) 51.7 750 51.7 750
20
90(1) 750(5) 51.7 750 51.7 750
40 90 1200(4) 11.6 168 25.1 364
1. Balanced trim design.
2. Balanced trim with restricted capacity plug.
3. Supply pressure limited to 1.5 to 2 barg (22 to 29 psig) for air-to-close (spring-to-open) actuator action.
4. Supply pressure limited to 2.1 to 2.8 barg (30 to 40 psig) for air-to-close (spring-to-open) actuator action.
5. Supply pressure limited to 1.5 to 3.2 barg (22 to 46 psig) for air-to-close (spring-to-open) actuator action.
6. Maximum supply pressure of 3.44 barg (50 psig) unless otherwise noted.
Fisher is a mark owned by Fisher Controls International LLC, a business of Emerson Process Management.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
All other marks are the property of their respective owners.
www.Fisher.com
EFisher Controls International LLC 2003; All Rights Reserved Printed in USA