Professional Documents
Culture Documents
Now in theaters
© 2019 Disney
Olaf Decoration Instructions
To begin, print out the templates onto regular paper. Overlay the freezer paper with
the shiny side down and trace the shapes onto the matte side of the freezer paper.
Write the felt color onto the shape. TIP: If more than one shape is the same colored
felt, gang those together as you trace the shapes.
Lay the freezer paper, shiny side down onto the felt. Use a warm iron to temporarily
adhere the freezer paper onto the felt. Press down for about 6 seconds or until the
paper adheres to the felt. Trim out the shapes with a sharp scissor.
TIP: Before removing the freezer paper from the shapes, read through the step-
by-step instructions on the next page and temporarily layer the shapes onto the
outline of Olaf to be sure all of the shapes are in order. Keep the freezer paper on
the delicate shapes while gluing for easier handling. Gently remove the freezer
paper when the glue has dried.
eyes
black white
black
black
black
center snowball
buttons
tooth
feet snowballs nose
back outline
white
front outline
white
© 2019 Disney
Olaf Decoration Instructions
Flat Instructions:
1. Cut out the front and back outline and shapes.
2. Using the chenille stems, make Olaf’s arms, hands and hair.
Follow the instructions shown to assemble. Set aside.
3. Using the front outline shape, begin layering and gluing
on shapes. Start with the center snowball first, and then his
buttons and feet.
4. Use the embroidery thread to stitch on Olaf’s eyebrows and
mouth. Glue on his nose, eyes and tooth as shown. Set the front
outline shape aside.
5. Using the back outline shape, glue Olaf’s hairs and waving arm
into place. brown chenille stems
6. Make a loop from the gold cord and tie a knot. Glue the cord to
the top of the back outline shape.
7. Apply glue to the front outline and press onto the back of the
decoration. Make a loop to create Olaf’s
8. Apply glue to Olaf’s remaining arm and glue into place. Your hands. Insert fingers through
decoration is complete! the loop and secure.
Puffy Instructions:
1. Follow the flat instructions, except do not glue the front and
the back outlines together.
2. Begin to blanket stitch the front and back pieces together.
Pause the blanket stitch to create an opening to insert filler.
Use a stick or pencil to push the filler into the decoration.
When filled, finish stitching to create a puffy decoration. Glue
into place his remaining arm and your decoration is complete!
© 2019 Disney
Sven Decoration
Instructions
brown To begin, print out the templates onto
regular paper. Overlay the freezer paper
with the shiny side down and trace the
shapes onto the matte side of the freezer
cheek hair paper. Write the felt color onto the shape.
TIP: If more than one shape is the same
colored felt, gang those together as you
trace the shapes.
brown Lay the freezer paper, shiny side down onto
the felt. Use a warm iron to temporarily
adhere the freezer paper onto the felt.
stirrup
Press down for about 6 seconds or until
the paper adheres to the felt. Trim out the
shapes with a sharp scissor.
TIP: Before removing the freezer paper
from the shapes, read through the step-
by-step instructions on the next page
and temporarily layer the shapes onto the
outline of Sven to be sure all of the shapes
are in order. Keep the freezer paper on
the delicate shapes while gluing for easier
handling. Gently remove the freezer paper
when the glue has dried.
nostrils
black stirrup
black
pupils
black
black
hooves
© 2019 Disney
Sven Decoration Instructions
Flat Instructions: Puffy Instructions:
1. Cut out the front and back outline and shapes. 1. Follow the flat instructions, except do not glue
the front and the back outlines together.
2. Using the front outline shape, begin layering and gluing on
shapes. Start with the belly shape, then the harness, and 2. Begin to blanket stitch the front and back pieces
then the stirrup. Move onto the bottom mane, layering on together. Change to a chain stitch across Sven’s
the top mane. tail, ear and antlers. Pause the blanket stitch to
create an opening to insert filler. Use a stick or
3. Use the embroidery thread to stitch on Sven’s mouth. Next,
pencil to push the filler into the decoration. When
glue on the nose shape, eyes, nostrils and top hair and then
filled, finish stitching to create a puffy decoration.
the cheek hair. Glue on the tail, hooves and space between
Sven’s legs. Set the front outline shape aside. 3. Glue the antlers, tail and ear together. Your
decoration is complete!
4. Cut off approximately 5" of craft wire. Make a “V” from the
wire. Using the back outline shape, glue the craft wire onto
Sven’s antlers.
5. Make a loop from the gold cord and tie a knot. Glue the
cord to the top of the back outline shape.
6. Apply glue to the front outline shape and press onto the
back of the decoration.
7. Apply glue to the light brown antler shapes and apply
to the front outline shape antlers. Your decoration is
complete!
eye whites
white
own
t br
eye area
ligh
light brown
top mane
light brown
antlers
light brown
dark brown
bottom mane
light brown
hair
tail
light brown
harness
burgundy
belly dark brown
light brown
nose
© 2019 Disney