Professional Documents
Culture Documents
Main Contractor:
TENAGA SWITCHGEAR SDN BHD – TOSHIBA TRANSMISSION & DISTRIBUTION SYSTEMS ASIA SDN BHD JV
Lot 3, Jalan Teknologi 3/6, Taman Sains Selangor 1, Kota Damansara, 47810 Petaling Jaya,
Selangor Darul Ehsan
Tel: 03-6140 6520 Fax: 03-6140 6530
No. Description
7. Contingency Plan
9. List of Appendix
1. Company background information
COMPANY DETAILS TENAGA SWITCHGEAR SDN BHD – TOSHIBA
TRANSMISSION & DISTRIBUTION SYSTEMS ASIA SDN
BHD JV
Lot 3, Jalan Teknologi 3/6, Taman Sains Selangor 1,
Kota Damansara, 47810 Petaling Jaya
No. Tel : 03-6140 6520
No. Fax : 03-6140 6530
SITE ADDRESS PMU 275/132KV Kangkar Tebrau GIS, Johor
• PRELIMINARY:
• Before any works start, TNB Permit to Work (PTW) must be obtained for the bays involved.
TNB shall also have their own authorized personnel to supervise the works throughout the
jobs at site. Any necessary clearance from NLDC must be arranged through TNB internal
procedure and area of work should be barricade.
• Before climbing on any equipment he has to ensure that the bay is completely isolated. If
he has any doubts he has to get clarified from the competent engineer and also the TNB
site supervisor.
• The works specified in the scope of works has to complete as per the given schedule with
full safety compliance.
• CONSTRAINTS:
• Work duration shall be extended due to bad weather i.e heavy rain, thunderstorm, etc
• There must be sufficient work space and /or clearance as directed by Superintending
Officer, No work shall be allowed to continue if contractor fail to provide adequate safe
working space and/or clearance on existing LIVE switchyard area.
• No work shall be done without the personnel of TNB or Competent Engineer
• Work area shall be barricaded with plastic chain (yellow)
• Proper signage indication the working area shall be made visible
• All work will do in “LIVE CONDITION” so please make sure all tools used must be fully
insulated and insulation glove must be worn during the work
2. SCOPE OF WORK / JOB SCOPE
3. METHOD OF STATEMENT.
The person in charge of a working party shall ensure that at all times the members of his party
thoroughly understand the work they have to do and the safety precautions required.
Safety Equipment
Safety equipment such as safety helmets, safety belts and harnesses, safety ropes must be
checked that it is in good condition before and after use
Objections
A person receiving an instruction regarding work on or the operation of High Voltage equipment
shall be report any objection he may have to carrying out instruction to the person issuing them
Safety Equipment
1. All apparatus, equipment and conductors shall be regarded as being LIVE until isolated and
proven DEAD; a DEAD apparatus is NOT SAFE until it is isolated and earthed
2. Earthed means connected to the general mass of earth in such manner as will ensure at all
time immediate discharge of electrical energy without danger, when applied to apparatus,
equipment, and conductors. All phase short circuited and efficiently connected to earth
3. Earthing bond for use at generating station and transmission substation shall have a cross
section of not less than 65sqmm
4. Earthing rod shall be insulated suitable for the system voltage which it is used
3. All spout shutters other than those made subject of a Permit to Work shall be locked shut
4. A High Voltage Zone under Permit to Work (PTW) shall be barricaded and all work by
contractors and their employees shall be confined within the zone and be in immediate
charge of a qualified person provided for under the Electricity Regulations 1994
5. Portable ladders (except of an approved typed) and tong objects are not allowed with the
High Voltage Zone. The use of such objects shall be under the direct supervision of the person in
charge of the work and when moved at ground level they shall be carried only in a horizontal
position as near to the ground as practicable
6. No person shall climb any structure in a High Voltage Zone unless the safe nature of the climb is
checked by a second person in the immediate vicinity. In every case one of the above two
person must be a competent engineer / person
7. No vehicle is allowed to move about, load or unload in a High Voltage Zone except as
approved by this person in charge
8. Cranes or other equipment shall be taken into or out of a substation via predetermined route
approved by the Authorized Person
General Precautions
Before carrying out any work on any part of High Voltage Apparatus / Zone made subject of a
Permit to Work it is good practice to verify that:-
D. Zone on with work may be carried out is properly barricaded and Danger Notices are
attached on or an adjacent to live apparatus at the limits of the zone
E. Caution Notices is fixed on all switchgears or apparatus which had been dead and on
which work is to proceed
F. All circuit main earth and additional earth are properly installed
Likelihood 1 2 3 4 5
Severity
5 5 10 15 20 25
4 4 8 12 16 20
3 3 6 9 12 15
2 2 4 6 8 10
1 1 2 3 4 5
JOB TITLE : replacement of the indication lamp and to retrieved AVR setting
works
OEM to follow
tripping and
guideline with
Download Software crash software failed to TNB AP
R operate. System 4 1 4 (L) NIL - TNB supervisor
software supervision. OEM
Shutdown &
personal
failure.
6. LIST OF MANPOWER
No. Name Position CIDB No. Expiry NTSP No. Expiry date
date
1 Lidya Ahmad Project W511B042012001 07/2025 TNB020083N 30.05.2022
manager
2 Muhammad engineer J91270120060001 28.12.2021 TNB000360N 25.07.2022
Nizam
3 Khairul Fatah engineer D81080420090023 23.10.2022 TNB034335N 30/05/2022
4 Ahmad Syazwan engineer T11280920030055 13.09.2021 TNB003413N 14/03/2022
5 Abu Bakar manager W21231120010020 12.06.2022 TNB001570N 30/05/2022
6 Mohd saiful tech 1870925KN1800246116 RENEW TNB034508N 25.07.2022
7 WAN SIEMENS tbc 28.07.2021 TNB002362896 14.10.2022
ZAINORHAZWAN SPECIALIST
7. CONTIGENCY PLAN
B. Action taken when non tripping fault or hazard occurs during does any unloading equipment
• TSG-TTDA JV supervisor will investigated location of fault happen
• Asked all workers who at fault location
• Discuss the outcome with the TNB personnel at site
• Any conclusion TNB personnel at site will decide
8. Propose Work Program
Period
Description
9am 10am 11am 12am 1pm 2pm 3pm
Safety Briefing and PTW issuance by GM
Barricade the working area.
ø22mm
YW Series Control Units
EP1140-0_YW Page 2 Tuesday, August 8, 2006 9:40 AM
10 10 10
CB
Reliable
30
15 15
30
Heavy-Duty Rugged Construction
Retained Locking Lever The YW series control units are designed to withstand
harsh operating conditions in factory environments. The
Lock Unlock rugged mechanical design provides reliability in critical
➀
➂ ➁ switching applications.
Save Safety
YW
series
ontacts Reliable
replace item,
Safety
Integrated Finger-safe
Terminal Cover
le
uction
Degree of Protection: IP20
The new YW contact blocks, full-voltage
adapter, and pilot light terminals feature
integrated finger-safe terminal covers to
prevent electrical shocks and ensure a
to withstand high degree of safety during wiring and
ronments. The maintenance.
bility in critical
n Contacts
e Emergency Stop Switches
Scored Surface
Satisfy International Standards
• Safety Lock Mechanism
If any part of the body inadvertently touches the
pushbutton, the contacts will not open until the operator
mechanism is locked. This feature prevents unintentional
operation of the emergency switch (compliant to EN418).
movable • Direct Opening Function
tact surfaces. Even if the contacts become welded together, an
operating force applied to the pushbutton forces the NC
contacts to open and ensures a break in the circuit
(compliant to IEC 60947-5-1, Annex K).
• Safe Pushbutton Design
The mushroom pushbutton is designed to ensure that an
object cannot become trapped between the mushroom
button and the panel, disabling the button operation. In
addition, the pushbutton is designed to prevent any
(3) Fully Depressed tampering from the front of the panel.
EP1140-0_YW Page 4 Tuesday, August 8, 2006 9:40 AM
4
EP1140-0_YW Page 5 Tuesday, August 8, 2006 9:40 AM
2NC YW1B-V4E02R
3NC YW1B-V4E03R
Pushlock
Red only
Pull/Turn Reset
1NO-1NC YW1B-V4E11R
1NO-2NC YW1B-V4E12R
2NO-1NC YW1B-V4E21R
Dimensions
Panel Thickness 0.8 to 6
Note: When pressed, the button is locked in
the depressed position, and is reset
10 10 10
41.4
0
ø4
45.8 32.5 30
Dimensions
M3.5 Terminal Screw Panel Thickness 0.8 to 6 Note: When pressed, the button is locked in
Full-Voltage Adapter
the depressed position, and is reset
when either pulled or turned clockwise.
10 10
10
41.4
0
ø4
45.8 32.5 30 All dimensions in mm.
5
EP1140-0_YW Page 6 Tuesday, August 8, 2006 9:40 AM
Pushbuttons
1NC YW1B-M1E01➀
2NO YW1B-M1E20➀
2NC YW1B-M1E02➀
1NO YW1B-A1E10➀
1NC YW1B-A1E01➀
2NC YW1B-A1E02➀
1NO-1NC YW1B-A1E11➀
Extended 1NO YW1B-M2E10➀
1NC YW1B-M2E01➀
2NC YW1B-A2E02➀
1NO-1NC YW1B-A2E11➀
Mushroom ø40mm 1NO YW1B-M4E10➀
1NC YW1B-M4E01➀
2NC YW1B-A4E02➀
1NO-1NC YW1B-A4E11➀
6
EP1140-0_YW Page 7 Tuesday, August 8, 2006 9:40 AM
0.5
M3.5 Terminal Screw
Contact Block Lock
Locking Ring
• Flush
(Button Diameter)
28.6
ø23.6
41.4
9
ø2
45.8 11 30
• Extended
(Button Diameter)
28.6
ø23.6
41.4
9
ø2
11
45.8 19 30
• Mushroom
(Button Diameter)
28.6
41.4
ø40
11
45.8 20.5 30
7
EP1140-0_YW Page 8 Tuesday, August 8, 2006 9:40 AM
Pilot Lights
Style Illumination Type Operating Voltage Type No. ➁ Lens Color Code
Flush A (amber), C (clear),
Full Voltage Without Lamp 250V AC/DC max. YW1P-1EQ0➁ G (green), R (red), S (blue),
W (white), Y (yellow)
6V AC/DC YW1P-1EQ2➁
12V AC/DC YW1P-1EQ3➁ A (amber), G (green),
PW (pure white), R (red),
LED 24V AC/DC YW1P-1EQ4➁
S (blue), W (white), Y (yellow)
110V AC/DC YW1P-1EQH➁ Built-in LED lamp: LSED-➂➁
100/110V AC YW1P-1EH5➁
A (amber), C (clear),
200/220V AC YW1P-1EM5➁ G (green), R (red), S (blue),
Incandescent W (white), Y (yellow)
115/120V AC YW1P-1EH25➁
Built-in incandescent lamp: LS-T6
230/240V AC YW1P-1EM45➁
Flush Marking Type A (amber), G (green), R (red),
Without Lamp 250V AC/DC max. YW1P-1BEQ0➁
Full Voltage S (blue), W (white), Y (yellow)
6V AC/DC YW1P-1BEQ2➁
12V AC/DC YW1P-1BEQ3➁ A (amber), G (green),
PW (pure white), R (red),
LED 24V AC/DC YW1P-1BEQ4➁ S (blue), W (white), Y (yellow)
Built-in LED lamp:
110V AC/DC YW1P-1BEQH➁ LSED-➂➁
230/240V AC/DC YW1P-1BEQM3➁
6V AC/DC YW1P-1BEQ5➁
A (amber), G (green), R (red),
Incandescent 12V AC/DC YW1P-1BEQ6➁ S (blue), W (white), Y (yellow)
Built-in incandescent lamp: LS-T➂
24V AC/DC YW1P-1BEQ7➁
Flush Marking Type 100/110V AC YW1P-1BEH2➁
Transformer Type A (amber), G (green),
200/220V AC YW1P-1BEM2➁ PW (pure white), R (red),
LED S (blue), W (white), Y (yellow)
115/120V AC YW1P-1BEH22➁ Built-in LED lamp:
LSED-6➁
230/240V AC YW1P-1BEM42➁
100/110V AC YW1P-1BEH5➁
8
EP1140-0_YW Page 9 Tuesday, August 8, 2006 9:40 AM
Style Illumination Type Operating Voltage Type No. ➁ Lens Color Code
Extended A (amber), C (clear),
Full Voltage Without Lamp 250V AC/DC max. YW1P-2TEQ0➁ G (green), R (red), S (blue),
W (white), Y (yellow)
6V AC/DC YW1P-2TEQ2➁
12V AC/DC YW1P-2TEQ3➁ A (amber), G (green),
PW (pure white), R (red),
LED 24V AC/DC YW1P-2TEQ4➁
S (blue), W (white), Y (yellow)
110V AC/DC YW1P-2TEQH➁ Built-in LED lamp: LSED-➂➁
100/110V AC YW1P-2TEH5➁
A (amber), C (clear),
200/220V AC YW1P-2TEM5➁ G (green), R (red), S (blue),
Incandescent W (white), Y (yellow)
115/120V AC YW1P-2TEH25➁
Built-in incandescent lamp: LS-T6
230/240V AC YW1P-2TEM45➁
Dome A (amber), C (clear),
Full Voltage Without Lamp 250V AC/DC max. YW1P-2EQ0➁ G (green), R (red), S (blue),
W (white), Y (yellow)
6V AC/DC YW1P-2EQ2➁
12V AC/DC YW1P-2EQ3➁ A (amber), G (green),
PW (pure white), R (red),
LED 24V AC/DC YW1P-2EQ4➁
S (blue), W (white), Y (yellow)
110V AC/DC YW1P-2EQH➁ Built-in LED lamp: LSED-➂➁
100/110V AC YW1P-2EH5➁
A (amber), C (clear),
200/220V AC YW1P-2EM5➁ G (green), R (red), S (blue),
Incandescent W (white), Y (yellow)
115/120V AC YW1P-2EH25➁
Built-in incandescent lamp: LS-T6
230/240V AC YW1P-2EM45➁
9
EP1140-0_YW Page 10 Tuesday, August 8, 2006 9:40 AM
8
9.
9.
ø2
ø2
24
24
46.2 9.5 29.6 46.2 10 29.6
Gasket Gasket
M3.5 Terminal Screw M3.5 Terminal Screw
Locking Ring Locking Ring
8
8
9.
9.
ø2
ø2
24
24
63.3 9.5 29.6 63.3 10 29.6
• Extended • Dome
Full Voltage Panel Thickness 0.8 to 6 Full Voltage Panel Thickness 0.8 to 6
Gasket Gasket
M3.5 Terminal Screw M3.5 Terminal Screw
Locking Ring Locking Ring
8
8
9.
9.
ø2
ø2
24
24
Gasket Gasket
M3.5 Terminal Screw M3.5 Terminal Screw
Locking Ring Locking Ring
8
8
9.
9.
ø2
ø2
24
24
10
EP1140-0_YW Page 11 Tuesday, August 8, 2006 9:40 AM
Illuminated Pushbuttons
Illumination ➂ Operating
Style Operation Contacts Type No. ➁ Lens Color Code
Type Voltage Code
Extended 1NO YW1L-M2E10Q0➁
1NC YW1L-M2E01Q0➁
Momentary 2NO YW1L-M2E20Q0➁
A (amber)
2NC YW1L-M2E02Q0➁
G (green)
1NO-1NC YW1L-M2E11Q0➁ 0 (without lamp) R (red)
Without Lamp
1NO YW1L-A2E10Q0➁ 250V AC/DC max. S (blue)
W (white)
1NC YW1L-A2E01Q0➁
Y (yellow)
Maintained 2NO YW1L-A2E20Q0➁
2NC YW1L-A2E02Q0➁
1NO-1NC YW1L-A2E11Q0➁
1NO YW1L-M2E10Q➂➁
1NC YW1L-M2E01Q➂➁
A (amber)
Momentary 2NO YW1L-M2E20Q➂➁ G (green)
2NC YW1L-M2E02Q➂➁ 2 (6V AC/DC) PW (pure white)
3 (12V AC/DC) R (red)
1NO-1NC YW1L-M2E11Q➂➁
LED 4 (24V AC/DC) S (blue)
1NO YW1L-A2E10Q➂➁ H (110V AC/DC) W (white)
1NC YW1L-A2E01Q➂➁ M3 (230/240V AC/DC) Y (yellow)
Maintained 2NO YW1L-A2E20Q➂➁ Built-in LED lamp:
LSED-➂➁
2NC YW1L-A2E02Q➂➁
1NO-1NC YW1L-A2E11Q➂➁
1NO YW1L-M2E10Q➂➁
1NC YW1L-M2E01Q➂➁
Momentary 2NO YW1L-M2E20Q➂➁ A (amber)
G (green)
2NC YW1L-M2E02Q➂➁ R (red)
1NO-1NC YW1L-M2E11Q➂➁ 5 (6V AC/DC) S (blue)
Incandescent 6 (12V AC/DC) W (white)
1NO YW1L-A2E10Q➂➁ 7 (24V AC/DC) Y (yellow)
1NC YW1L-A2E01Q➂➁
Built-in incandescent lamp:
Maintained 2NO YW1L-A2E20Q➂➁ LS-T➂
2NC YW1L-A2E02Q➂➁
1NO-1NC YW1L-A2E11Q➂➁
Extended with 1NO YW1L-MF2E10Q0➁
Full Shroud 1NC YW1L-MF2E01Q0➁
Momentary 2NO YW1L-MF2E20Q0➁
A (amber)
2NC YW1L-MF2E02Q0➁
G (green)
1NO-1NC YW1L-MF2E11Q0➁ 0 (without lamp) R (red)
Without Lamp
1NO YW1L-AF2E10Q0➁ 250V AC/DC max. S (blue)
W (white)
1NC YW1L-AF2E01Q0➁
Y (yellow)
Maintained 2NO YW1L-AF2E20Q0➁
2NC YW1L-AF2E02Q0➁
1NO-1NC YW1L-AF2E11Q0➁
1NO YW1L-MF2E10Q➂➁
1NC YW1L-MF2E01Q➂➁
A (amber)
Momentary 2NO YW1L-MF2E20Q➂➁ G (green)
2NC YW1L-MF2E02Q➂➁ 2 (6V AC/DC) PW (pure white)
3 (12V AC/DC) R (red)
1NO-1NC YW1L-MF2E11Q➂➁
LED 4 (24V AC/DC) S (blue)
1NO YW1L-AF2E10Q➂➁ H (110V AC/DC) W (white)
1NC YW1L-AF2E01Q➂➁ M3 (230/240V AC/DC) Y (yellow)
Maintained 2NO YW1L-AF2E20Q➂➁ Built-in LED lamp:
LSED-➂➁
2NC YW1L-AF2E02Q➂➁
1NO-1NC YW1L-AF2E11Q➂➁
1NO YW1L-MF2E10Q➂➁
1NC YW1L-MF2E01Q➂➁
Momentary 2NO YW1L-MF2E20Q➂➁ A (amber)
G (green)
2NC YW1L-MF2E02Q➂➁ R (red)
1NO-1NC YW1L-MF2E11Q➂➁ 5 (6V AC/DC) S (blue)
Incandescent 6 (12V AC/DC) W (white)
1NO YW1L-AF2E10Q➂➁ 7 (24V AC/DC) Y (yellow)
1NC YW1L-AF2E01Q➂➁
Built-in incandescent lamp:
Maintained 2NO YW1L-AF2E20Q➂➁ LS-T➂
2NC YW1L-AF2E02Q➂➁
1NO-1NC YW1L-AF2E11Q➂➁
Note: Specify a lens color code in place of ➁ in the Type No.
Specify an operating voltage code in place of ➂ in the Type No.
11
EP1140-0_YW Page 12 Tuesday, August 8, 2006 9:40 AM
Illumination ➂ Operating
Style Operation Contacts Type No. ➁ Lens Color Code
Type Voltage Code
Mushroom ø40mm 1NO YW1L-M4E10Q0➁
1NC YW1L-M4E01Q0➁
Momentary 2NO YW1L-M4E20Q0➁
A (amber)
2NC YW1L-M4E02Q0➁
G (green)
1NO-1NC YW1L-M4E11Q0➁ 0 (without lamp) R (red)
Without Lamp
1NO YW1L-A4E10Q0➁ 250V AC/DC max. S (blue)
W (white)
1NC YW1L-A4E01Q0➁
Y (yellow)
Maintained 2NO YW1L-A4E20Q0➁
2NC YW1L-A4E02Q0➁
1NO-1NC YW1L-A4E11Q0➁
1NO YW1L-M4E10Q➂➁
1NC YW1L-M4E01Q➂➁
A (amber)
Momentary 2NO YW1L-M4E20Q➂➁ G (green)
2NC YW1L-M4E02Q➂➁ 2 (6V AC/DC) PW (pure white)
3 (12V AC/DC) R (red)
1NO-1NC YW1L-M4E11Q➂➁
LED 4 (24V AC/DC) S (blue)
1NO YW1L-A4E10Q➂➁ H (110V AC/DC) W (white)
1NC YW1L-A4E01Q➂➁ M3 (230/240V AC/DC) Y (yellow)
Maintained 2NO YW1L-A4E20Q➂➁ Built-in LED lamp:
LSED-➂➁
2NC YW1L-A4E02Q➂➁
1NO-1NC YW1L-A4E11Q➂➁
1NO YW1L-M4E10Q➂➁
1NC YW1L-M4E01Q➂➁
Momentary 2NO YW1L-M4E20Q➂➁ A (amber)
2NC YW1L-M4E02Q➂➁ G (green)
5 (6V AC/DC) R (red)
1NO-1NC YW1L-M4E11Q➂➁
Incandescent 6 (12V AC/DC) S (blue)
1NO YW1L-A4E10Q➂➁ 7 (24V AC/DC) W (white)
1NC YW1L-A4E01Q➂➁ Built-in incandescent lamp:
Maintained 2NO YW1L-A4E20Q➂➁ LS-T➂
2NC YW1L-A4E02Q➂➁
1NO-1NC YW1L-A4E11Q➂➁
Note: Specify a lens color code in place of ➁ in the Type No.
Specify an operating voltage code in place of ➂ in the Type No.
0.5
M3.5 Terminal Screw
Contact Block
• Extended • Extended with Full Shroud
28.6
(Button Diameter)
28.6
ø23.6
41.4
41.4
9
ø2 8.2
ø2
11 30 45.8 19 30
45.8 19
• Mushroom
(Button Diameter)
28.6
41.4
ø40
11
45.8 20.5 30 All dimensions in mm.
12
EP1140-0_YW Page 13 Tuesday, August 8, 2006 9:40 AM
Selector Switches
Knob Type
Style
13
EP1140-0_YW Page 14 Tuesday, August 8, 2006 9:40 AM
10
10
0.5
C M3.5 Terminal Screw
L R Contact Block 45°
Locking Ring 45°
LOCK
Operator Position
28.6
41.4
3-Position
9
ø2
ø2
11 Kn 7.6
45.8 24 30 Di ob
am
ete
r
90°
2-Position
Accessories
Package
Name & Shape Type No. Description & Dimensions (mm)
Quantity
Locking Ring Wrench Metallic tool used to tighten the
110
plastic locking ring when installing 8
ø2
the YW series control unit on a
MW9Z-T1 panel. 1
OR-55 1
ø11.6
59
Rubber Mounting Hole Plug Used for plugging unused mounting holes in the panel. ø29
Color: Black
OB-31PN05 5
3.5
ø25
3.5
Metallic Mounting Hole Plug Used for plugging unused mounting holes in the ø25.8
panel.
3
Locking Ring
14
EP1140-0_YW Page 15 Tuesday, August 8, 2006 9:40 AM
R6
6.5
93
HW9Z-KL1 1
30
70
24
0
ø5
ø2
2
.2
Waterproof Gasket
29.5 Thickness 0.5
Pad Lock Hole ø8
30
23 ±1 LS-T3P 30V, 1W
10
M3.5 Terminal Screw
YW-E01P Contact: 1NC 41.4
41.4
15
EP1140-0_YW Page 16 Tuesday, August 8, 2006 9:40 AM
ø23.6
Mushroom Y (yellow)
YW9Z-B14➀PN10
ø40mm
6
10.8
Lens A (amber)
8
(for pilot lights) C (clear) 9.
ø2
G (green)
Flush YW9Z-PL11➁PN10 R (red) 10
S (blue)
W (white) 8.5
Y (yellow)
A (amber) 8
9.
C (clear) ø2
Flush G (green)
YW9Z-PL11B➁PN10 10
Marking R (red)
S (blue)
Y (yellow) 9
8
9.
ø2
14.5
Lens 6
3.
(for illuminated pushbuttons) ø2
Extended YW9Z-L12➁PN10
A (amber)
C (clear) 9.3
G (green) 0
ø4
10
R (red)
S (blue)
ø23.6
Mushroom Y (yellow)
YW9Z-L14➁PN10
ø40mm
6
10.8
Marking Plate
7
2.
ø2
— YW9Z-PP12PN10 — 10
21 2
4.4
Marking Plate
2
7.
ø16
— YW9Z-P12PN10 — 10
15.2 1.4
5
16
EP1140-0_YW Page 17 Tuesday, August 8, 2006 9:40 AM
ERGENCY 0
EM ø6
Blank HWAV-0 HWAV-0 1
Plastic (yellow)
HWAV ø2
2
1.5 mm thick
STOP
1.6 0.9
EMERGENCY STOP HWAV-27 HWAV-27 1
• Legend “Emergency Stop”
is indicated outside a ø44mm circle.
25
2
47 22
ø2
2
ø66
ø74
52
ø66.8
ø80
32
42
EMO Switch Guard EMO Switch Guard
SEMI S2 compliant (Note 1) SEMI S2 compliant
HW9Z-KG2 HW9Z-KG4
35
36.5 25
ø2
2.
2
ø2
2
ø75
ø90
67
ø76.1
ø90
50
EMO Switch Guard EMO Switch Guard
SEMI S2 compliant (Note 1) SEMI S2 compliant
SEMATECH compliant (Note 2) SEMATECH compliant (Note 2)
Material: Polyamide (PA6) • Degree of protection IP65 applies to the combination of an emergency stop
Color: Yellow, Munsell 2.5Y 8/10 equivalent switch and an EMO switch guard.
Degree of protection: IP65
2-ø3.5 40
. Mounting Holes 48
Primary Voltage
Type No. Applicable Lamp Rating
(50/60 Hz)
52
110V AC TWR516 One full voltage type illuminated
115V AC TWR5116 unit containing LED lamp LSED-6
120V AC TWR5126 (6V AC/DC) or incandescent lamp
LS-T6 (6.3V)
220V AC TWR526
41
40
230V AC TWR5236
240V AC TWR5246
380V AC TWR5386
440V AC TWR546
480V AC TWR5486 Note: Finger-safe terminal cover is supplied with the transformer.
17
EP1140-0_YW Page 18 Tuesday, August 8, 2006 9:40 AM
Safety Precautions
• Turn off the power to the YW series control units before starting in- ing lamps.
stallation, removal, wiring, maintenance, and inspection of the • For wiring, use wires of a proper size to meet the voltage and cur-
products. Failure to turn power off may cause electrical shocks or rent requirements. Tighten the M3.5 terminal screws to a tighten-
fire hazard. ing torque of 1.0 to 1.3 N·m. Failure to tighten the terminal screws
• To avoid burning your hand, use the lamp holder tool when replac- may cause overheating and fire.
Instructions
Panel Mounting 1. To remove the full voltage unit, squeeze the full voltage unit from
both sides to disengage the latch as shown, and pull it out. Like
• Remove the contact block from the operator (for pilot lights, re- the transformer unit, the full voltage unit can also be pulled out by
move the transformer or full voltage unit from the pilot light). Re- inserting a flat screwdriver into the latch hole as shown.
move the locking ring from the operator. Insert the operator into the
panel cut-out from the front, tighten the locking ring from the back, 2. To reinstall, place the TOP markings on the operator and the latch
then install the contact block to the operator. on the full voltage unit in the same direction, and insert the oper-
ator into the full voltage unit.
• Removing and Installing the Contact Block
• Notes for Panel Mounting
➁
1. Use the optional locking ring wrench (MW9Z-T1) to mount the op-
➀
erator onto a panel. Tightening torque must not exceed 2.0 N · m.
Do not use pliers. Excessive tightening will damage the locking
ring.
➂
2. For the contact blocks and transformers housing LED and incan-
descent lamps, make sure not to press the lamps too hard, other-
wise the lamp socket may be impaired.
Marking Plate
Marking Plate
Lens
Lens
Full Shroud
• Removing and Installing the Transformer Unit
1. Insert a flat screwdriver (5 mm wide at maximum) into the latch
hole on the transformer unit as shown in the photo below, and dis- Mushroom
engage the latch. Then pull out the operator.
2. To reinstall, place the TOP marking on the operator and the latch
in the same direction, and push the operator into the transformer
unit.
Marking Plate
➀
Lens
Marking
For YW series pilot lights and illuminated pushbuttons, legends and
➁ symbols can be engraved on the built-in marking plates, or printed
mylar film can be inserted under the lens for labeling purposes.
Mylar film is not supplied with the control units and must be sup-
• Removing the Full Voltage Unit plied by the end user.
➁
18
EP1140-0_YW Page 19 Tuesday, August 8, 2006 9:40 AM
ø1
➀
Engraving Area Engraving Area
1.2
1.0
-0.2
ø22.7 -0.2
0
0
ø17.2
➁ ➁
0
20.8 -0.2
0
15.0 -0.2 Tightening Torque for Terminal Screws
Tighten terminal screws to a torque between 1.0 and 1.3 N·m.
0.1-mm-thick × 2 sheets or 0.2-mm-thick × 1 sheet
Film material: Mylar (recommended) Anti-rotation Ring and Mounting Panel
Note: Marking film is not supplied with the pilot light or illu- Turn the TOP marking on the operator and the ▲ mark on the anti-
minated pushbutton. rotation ring to the recess on the mounting panel.
• Replacement (LED and incandescent lamps) Projections (▲ mark)
Lamps can be replaced using the lamp holder tool (OR-55) from the
front of the panel, or by removing the contact block from the opera-
tor unit.
• Removing the Lamp from the Front of the Panel
To remove, gently insert the lamp holder tool onto the lamp head.
Then push slightly, and turn the lamp holder tool to the left.
Anti-rotation Ring Locking Ring
Contact Bounce
When the button is reset by pulling or turning, the NC main contacts
will bounce. When pressing the button, the NO monitor contacts will
bounce.
When designing a control circuit, take the contact bounce time into
consideration (reference value: 20 ms).
Projection
Pilot Light Illuminated Pushbutton
Nameplate
When anti-rotation is not required, remove
Removing Contact Blocks the projection from the nameplate using
pliers.
and Full Voltage Adapter Nameplate
Insert a flat screwdriver between the Handling
latch and contact block mounting
Do not expose the switch to excessive
adapter, and disengage the latch.
shock and vibration, otherwise the switch
may be deformed or damaged, causing
malfunction or operation failure.
19
EP1140-0_YW Page 20 Tuesday, August 8, 2006 9:40 AM
Instructions
LED Illumination [Protection Example 1] For AC circuit
LED lamps consist of semiconductors. If the applied voltage
exceeds the rated voltage, LED elements deteriorate due to over- LED with
heat, resulting in significant decrease in luminance, hue change, or transformer
Ordering Information
• When ordering, specify the Type No. and quantity. • Replacement contact blocks are supplied in a package containing
10 pieces.
Specifications and other descriptions in this catalog are subject to change without notice.
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: +81-6-6398-2571, Fax: +81-6-6392-9731
E-mail: products@idec.co.jp
IDEC CORPORATION (USA) IDEC ELEKTROTECHNIK GmbH IDEC IZUMI (H.K.) CO., LTD.
1175 Elko Drive, Sunnyvale, CA 94089-2209, USA Wendenstrasse 331, 20537 Hamburg, Germany Unit 1505-07, DCH Commercial Centre No. 25,
Tel: +1-408-747-0550 / (800) 262-IDEC (4332)
T Tel: +49-40-25 30 54 - 0, Fax: +49-40-25 30 54 - 24 Westlands Road, Quarry Bay, Hong Kong
Fax: +1-408-744-9055 / (800) 635-6246 E-mail: service@idec.de Tel: +852-2803-8989, Fax: +852-2565-0171
E-mail: opencontact@idec.com IDEC (SHANGHAI) CORPORATION E-mail: info@hk.idec.com
IDEC CANADA LIMITED Room 608-609, 6F, Gangtai Plaza, No. 700, IDEC TAIWAN CORPORATION
Unit 22-151, Brunel Road, Mississauga, Ontario, Yan'an East Road, Shanghai 200001, P.R.C. 8F-1, No. 79, Hsin Tai Wu Road, Sec. 1,
L4Z 1X3, Canada Tel: +86-21-5353-1000, Fax: +86-21-5353-1263 Hsi-Chih, Taipei County, Taiwan
Tel: +1-905-890-8561, Toll Free: (888) 317-4332 E-mail: idec@cn.idec.com Tel: +886-2-2698-3929, Fax: +886-2-2698-3931
Fax: +1-905-890-8562 IDEC (SHANGHAI) CORPORATION E-mail: service@idectwn.com.tw
E-mail: sales@ca.idec.com Beijing Office IDEC IZUMI ASIA PTE. LTD.
IDEC AUSTRALIA PTY. LTD. Unit 1002, No. 10 Kuntai Building, Zhaowai Dajie, No. 31, Tannery Lane #05-01, Dragon Land
2/3 Macro Court, Rowville, Victoria 3178, Australia Zhao Yang District, Beijing, 100020, P.R.C. Building, Singapore 347788
Tel: +61-3-9763-3244, Toll Free: 1800-68-4332 Tel: +86-10-6599-5541, Fax: +86-10-6599-5540 Tel: +65-6746-1155, Fax: +65-6844-5995
Fax: +61-3-9763-3255 E-mail: info@sg.idec.com
IDEC (SHENZHEN) CORPORATION
E-mail: sales@au.idec.com Unit AB-3B2, Tian Xiang Building, Tian’an Cyber Park,
IDEC ELECTRONICS LIMITED Fu Tian District, Shenzhen, Guang Dong 518040, P.R.C.
Unit 2, Beechwood, Chineham Business Park, Tel: +86-755-8356-2977, Fax: +86-755-8356-2944
Basingstoke, Hampshire RG24 8WA, UK
Tel: +44-1256-321000, Fax: +44-1256-327755
www.idec.com E-mail: sales@uk.idec.com
4. Read one group of settings from the device into a Settings Editor Window
The user will be prompted to enter the group required.
5. Save Settings.
6. Click file > save
7. A dialog box is displayed for the user to choose a directory to save the files.
The current path is shown at the top of the box. Underneath is a control to
select the target disk drive, then a list of the directories available on that
drive. Double click on a name in the list to enter a sub-directory. If
necessary you can create a directory by typing a name into the control in
the Create Directory area and pressing Create.
8. Click ‘Save’
800
B B
-F87BBHI/M1 -F96BBHI/M1 -X87BBHI/M1 TEST TERMINAL BLOCK
-F87BBHI/M1 MAIN 1 ZONE HIGH IMPEDANCE DIFFERENTIAL RELAY
-F96BBHI/M1 MAIN 1 ZONE BBP CT SUPERVISION RELAY
-X87BBHI/M2 TEST TERMINAL BLOCK
-F87BBHI/M2 MAIN 2 ZONE HIGH IMPEDANCE DIFFERENTIAL RELAY
-X87BBHI/M2
-F72/1
-F52/1
-H1
-XPS
E -SH E
=D00+RBB1
75
275-BBH/RP
F CLIENT: CONTRACTOR: TENAGA SWITCHGEAR SDN. BHD.- TITLE: = D00 + RBB1 / A11 F
DATE 17.11.15 TENAGA TOSHIBA TRANSMISSION & 275kV SCHEMATIC DRAWING
DRAWN MAR NASIONAL BERHAD (200866-W) DISTRIBUTION SYSTEM ASIA SDN. BHD. JV 275kVHIGH IMPEDANCE BUSBAR PROTECTION
SUPPLIER: DRAWING NO.: REV.: THIS SHEET: 13
AS-BUILT 11.03.20 MAR/FAUZI/EHSAN/ABU CHECKED FAUZI/EHSAN CONTRACT NO.: TNB 99/2015 TOSHIBA TRANSMISSION & PANEL NO.1 FRONT VIEW & PART LIST
REV. DATE DRN/CHK/REVIEWED REVIEWED ABU TENDER NO.: TNBT 808814 DISTRIBUTION SYSTEM ASIA SDN. BHD. SUBSTATION: PMU KANGKAR TEBRAU 275/132kV GIS TTDA KTRU 808814 275 S 11-BBHI AS-BUILT NEXT SHEET: 14
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
MAIN 1 ZONE MAIN 1 ZONE MAIN 2 ZONE MAIN 2 ZONE RESERVE ZONE RESERVE ZONE
LAMP TEST IN SERVICE OUT SERVICE IN SERVICE OUT SERVICE IN SERVICE OUT SERVICE
A A
L101 L101
SH.31/D7
13 6 8 6 8 6 8
-SLT -S87M1 IN -S87M2 IN -S87R IN
SH.84 OUT SH.84 OUT SH.84 OUT
SH.84
14 5 7 5 7 5 7
B B
L21
A A A A A A
-D1 -D2 -D3 -D4 -D5 -D6
SH.84 K SH.84 K SH.84 K SH.84 K SH.84 K SH.84 K
C C
D X1 X1 X1 X1 X1 X1 D
-H2 -H3 -H4 -H5 -H6 -H7
SH.84 SH.84 SH.84 SH.84 SH.84 SH.84
X2 X2 X2 X2 X2 X2
L102 L102
SH.31/D7
E E
:to replace
PUSH BUTTON 13 23
A MANUFACTURER : IDEC IZUMI A
TYPE : YW1B-M1E20B
COLOR : BLACK 14 24
CONTACT : 2 N/O
DIODE A
MANUFACTURER : PHOENIX
TYPE : UT4-MTD
RATING : 1300V, 0.5A K
AUXILIARY RELAY
c/w FRONT CONNECTED BASE 2 4 5 6 7 9 8
MANUFACTURER : OMRON
TYPE : MKS3P c/w BASE PF113A-E 10
ORDERING CODE : MKS3P-I 110 VDC 1 3 11
E E
RATED VOLTAGE : 110V DC
POWER CONSUMPTION : 2.7 VA +RBB1 -K52/X1 SH.49/D2 SH.77/C7 SH.75/C3
TYPICAL PICK-UP TIME VALUE : 30ms
+RBB1 -K87BBHI/M1X SH.47/D3 SH.77/C2 SH.75/C2
(MAKE/BREAK CONTACTS)
TYPICAL DROP-OUT TIME : 20ms +RBB1 -K87BBHI/M2X SH.47/D5 SH.77/C3 SH.75/C2
(MAKE/BREAK CONTACTS) +RBB1 -K87BBHI/RX SH.47/D7 SH.77/C4 SH.75/C3
+RBB2 -K87BBHI/CX SH.48/D3 SH.77/C8 SH.75/C8
F CLIENT: CONTRACTOR: TENAGA SWITCHGEAR SDN. BHD.- TITLE: = D00 + RBB1 & RBB2 / X4 F
DATE 17.11.15 TENAGA TOSHIBA TRANSMISSION & 275kV SCHEMATIC DRAWING
DRAWN MAR NASIONAL BERHAD (200866-W) DISTRIBUTION SYSTEM ASIA SDN. BHD. JV 275kV HIGH IMPEDANCE BUSBAR PROTECTION
SUPPLIER: DRAWING NO.: REV.: THIS SHEET: 84
AS-BUILT 11.03.20 MAR/FAUZI/EHSAN/ABU CHECKED FAUZI/EHSAN CONTRACT NO.: TNB 99/2015 TOSHIBA TRANSMISSION & APPARATUS LIST
REV. DATE DRN/CHK/REVIEWED REVIEWED ABU TENDER NO.: TNBT 808814 DISTRIBUTION SYSTEM ASIA SDN. BHD. SUBSTATION: PMU KANGKAR TEBRAU 275/132kV GIS TTDA KTRU 808814 275 S 11-BBHI AS-BUILT NEXT SHEET: 85
1 2 3 4 5 6 7 8