Professional Documents
Culture Documents
Programming Instructions Timing Diagrams Timing Diagrams Timing Diagrams Functional Description
Programming Instructions Timing Diagrams Timing Diagrams Timing Diagrams Functional Description
Functional Description
Programming Instructions
1. ON DELAY [ ]
1.
1. ON DELAY ( )
T t T The Timer starts when both Power (P) and Signal (S)
Apply power & hold the SET key for > 3 sec.
8 functions A1- A2 are applied.The relay is energized at the end of
OR P :
Wide operating voltage : 24 to 240 V AC/DC Preset Time (T) and remains ON till Power is removed.
Press both ADJ & SET key for > 3 sec. After power ON. B1 2. CYCLIC OFF/ON {OFF Start, (Sym, Asym)} [
S : ]
Multi Range : 0.1 sec to 999 hrs. Now follow the steps given below T T-ON and T-OFF can be same or different. The relay
Up / Down counting modes R : keeps on changing its status till the power is removed.
3 Digit LCD for Preset Time and Run Time KEY DISPLAY RESULT 3. CYCLIC ON/OFF {ON Start, (Sym, Asym)} [ ]
Clear LED indication of Relay status 2. CYCLIC OFF/ON {OFF Start, (Sym, Asym)} [ ]
This function is quite similar to the function ‘ ‘ but initially
Key lock Function Press ADJ key to select P : A1- A2 T T t T T T t
the relay is ON for period T-ON after the Power is applied.
Conforms to IEC standards of EMI/EMC F 5:39 desired function (e.g. F)
B1
4. SIGNAL ON/OFF [ ]
Compact size (17.5 mm single width ADJ
HM S : The output relay is turned ON for Preset Time (T) whenever
module) T OFF T ON T OFF T ON the Signal(S) is applied or removed. (Refer Note: 2)
R : 5. SIGNAL OFF DELAY [ ]
Confirms function Output relay becomes ON when Signal (S) is applied. The Timer
F 5:39 Then Range indicator blinks 3. CYCLIC ON/OFF {ON Start, (Sym, Asym)} [ ] Duration(T) starts when Signal (S) is removed. At the end of
SET HM
A1- A2 T T t T T T t Timer Duration (T)the output relay goes OFF. Signal (S),
P :
if applied during the Timer Duration(T) will re-trigger the Timer
Press ADJ key to select range S : B1 and the total duration will be extended
UP / DN F 5:39 (e.g. HM range ‘ HM ‘) T ON T OFF T ON T OFF 6. INTERVAL [ ]
SET ADJ ADJ HM When Signal (S) is applied, the Timer starts and the output
R :
LED INDICATION relay is energized. The output relay becomes OFF at the end
FOR 4. SIGNAL ON/OFF [ ] T T T t T t of Timer Duration (T).
RELAY STATUS Confirms range selection. 7. SIGNAL OFF / ON [ ]
P : A1- A2
F 5:39 1st digit of Preset time blinks. When Signal (S) is applied or removed, the relay changes
SET HM (For modes ‘B’ & ‘C’ two preset times S : B1 its state after Timer Duration (T) (Refer Note : 2)
‘On’ & ‘Off’ to be set ) T T T T 8. ONE SHOT OUTPUT [ ]
R : When Signal (S) is applied, the Timer Duration (T) starts.
1. PRESET TIME: The Timer Duration selected by the user. Press ADJ key to adjust desired
F 8:39 preset time digit (e.g.from 5 to 8)
At the end of Timer duration (T), the relay gets energized
HM T : PRESET TIME t : PERIOD < T P : POWER S : SIGNAL R : RELAY for approximately 1 sec.(Refer Note : 2)
ADJ
2. RUN TIME: In Down counting ( ) mode it indicates the
remaining time while in Up counting ( ) mode
it indicates the elapsed time. 1. For Power-ON operation the terminal B1 and A1 must
Press Set to confirm 1st digit 5.
5. SIGNAL OFF DELAY [ ]
T t t T t
be permanently connected.
3. Up/Down ( ) blinks during the Timer Duration (T) SET
F 8:39 selection, now 2nd digit blinks
P : A1- A2 2. In case of all modes except mode G a change in
HM
Signal(s) status during the Timing Duration (T), does
S : B1 not affect output status but resets timing and
THE KEYS Change with ADJ Key T re-triggers timing.
ADJ
F 8:09 (e.g.from 3 to 0) R :
HM 3. Output de-energises when device enters PROGRAM
6. INTERVAL [ ]
KEY OPERATION RESULT T T t t T
MODE and starts new cycle after coming out of
Confirms 2nd digit selection, PROGRAM MODE.
P : A1- A2
SET
Apply Power & Hold Program Mode
SET
F 8:09 now 3rd digit of Preset Time
B1
4. Loads which have current requirement > 1mA, can
the key for >3 sec. HM blinks. S : only be used as Optional Load. For e.g. Contactor
T
OR R : Coil, AC Relay Coil, etc.
Press both > 3 sec Program Mode Change with ADJ Key
ADJ SET
after power on ADJ
F 8:06 (e.g. from 9 to 6) 7. SIGNAL OFF / ON [ ]
T T t T T t T t
HM
CONNECTIONS
P : A1- A2
Press in Program mode Select, Edit parameter
SET
Now UP / DOWN Indicator blinks S : B1 Supply DPST Relay SPDT Relay
Press in Program mode Edit blinking parameter SET
F 8:06 T T T T
Connection Connection Connection
ADJ HM R : 15
Press for > 3 sec. Reset Timer 8. ONE SHOT OUTPUT [ ] T T t t T
SET
during Timer operation Change with ADJ Key
F 8:06 (e.g.from DOWN to UP) P : A1- A2 24 -240 V 18
ADJ HM AC/DC
Press for > 3 sec. Lock / Unlock Preset Time S :
B1
ADJ
during Timer operation Confirms counting mode. T 1 SEC. 16
00.0 Program Over.
R :
Press during Timer Edit Preset Time
F
8:06 OPTIONAL 8A, 240 V AC 8A, 240 V AC
SET
SET HM Timer starts working normally. T : PRESET TIME t : PERIOD < T P : POWER S : SIGNAL R : RELAY LOAD > 1 mA 24V DC 24V DC
operation during Timer operation
SERIES : DIGICON
TECHNICAL SPECIFICATIONS MULTI - FUNCTION DIGITAL TIMER
CAT.No. V0DDTS V0DDTD
SUPPLY CHARACTERISTICS
Nominal Supply (Un) 24 - 240 VAC / DC (50 - 60 Hz, +/-2 Hz) CAT. NOS.:
V0DDTS
Limits -15 % to +10% of Un
V0DDTD RoHS
Power Consumption (Max.) ~ 10 VA
RELAY OUTPUT CHARACTERISTICS Caution :
1. Always follow instructions stated in this
Contact Arrangement 1 C/O 2 NO product leaflet.
2. Before installation, check to ensure that
Contact Rating 240 VAC / 24 VDC @ 8A (resistive) 240 VAC / 24 VDC @ 8A (resistive) the specifications agree with the intended
application.
Contact Material Ag Ni 3. Installation to be done by skilled electrician.
7 4. Automation & Control devices must
Mechanical Life Expectancy 2 x 10
be properly installed so that they are
5
Electrical Life Expectancy 1 x 10 protected against any risk of involuntary
actuations.
Switching Frequency (Max.) 1800 Operations / hr. @ rated load
Status Indication on panel Red LED - Relay ON OVERALL DIMENSIONS
35 - mm-SYMMETRICAL
BASE MOUNTING 76.0
Modes Available 1. ON Delay ( ) 2. Cyclic OFF/ON (Sym, Asym) ( ) 3. Cyclic ON/OFF(Sym, Asym) ( ) 4. Signal
DIN RAIL
ON/OFF ( ) 5. Signal Off Delay ( ) 6. Interval ( ) 7. Signal OFF/ON ( ) 8. One Shot Output ( )
h:m m:s hr min sec
100.0 C/C
Timing Ranges
67.0
89.0
45.0
9:59 9:59 999 999 999
99.9 99.9 99.9
Repeat Accuracy +/-0.5% of selected range
Variation in timing due to voltage change +/-2% ALL DIMENSIONS ARE IN mm