Professional Documents
Culture Documents
A Report On Structural Analysis of Roof Truss: 1. General Data and Load Calculation
A Report On Structural Analysis of Roof Truss: 1. General Data and Load Calculation
1.1 Introduction
This report has been prepared as a part of the structural engineering analysis and design of
the Commercial building.
The planned building is 1 story tall building with roof truss. The functional parameters relevant to
the design of the facilities would comprise those related to the user’s requirement and guided by
the design standards via the standard norms, standards bye -laws and municipal bye - laws.
Architectural and Planning design criteria has been made with the consultation of different
experts such as Architect, Planner and Structural Engineer etc.
The massive data inputs, design analysis, calculations and outputs of the result are computer
aided by the Structural analysis and design software called Etabs Version 18.0.2 It provides the
Structural Engineer with all the tools necessary to create, modify, analyze, design, and optimize
the structural elements in a building model.
Based on the final results, the designs have been performed and drawings were prepared using
AutoCAD.
The characteristic compressive strength for concrete of 20 N/mm2 (M20) was used in all structural
members and characteristic strength of 500 N/mm2 (Fe500) was used for reinforcing steel. And
Fe 250 MS steel is used as the steel structures members.
Page 1 of 15
29/12/2020
Design Parameters
ARCHITECTURAL AND FUNCTIONAL REQUIREMENTS
CONSTRUCTION SITE
LOCATION Pepsicola Kathmandu
Soil type Type II (Medium Soil)
Bearing capacity 90KN/m2
DIMENSIONS AND MATERIALS
Slab thickness No Slab
METHOD OF ANALYSIS
Analysis method adopted for EQ resistant design : Seismic coefficient
Level of design : Professionally engineered structure
Total number of design load cases considered : As Per IS 456:2000, IS 800:2007
Page 2 of 15
29/12/2020
Design Parameters
Height of truss : 3’
No of truss : 10 nos.
The truss was analyzed using structural analysis software ETABS 16.02 ver 2016. First the truss was
modelled and the material was defined as Fe 250. Then the Load patterns were defined as
Then the load patterns were automatically generated by the software Etabs ver 18.0.2 as per IS 875 Part
3. Then the wind loads were applied on the purlins as distributed load and the lateral wind loads were
applied by the software on 0 and 90 deg angle.
Then the model was analyzed, then designed and finally verified whether all members passed or not.
Page 3 of 15
29/12/2020
List of Figures
1. Truss Model
Page 4 of 15
29/12/2020
2. Loads applied
Page 5 of 15
29/12/2020
3. Deformed Shape
Page 6 of 15
29/12/2020
4. Structural Output
Page 7 of 15
29/12/2020
Wx Leeward Wx Windward
Page 8 of 15
29/12/2020
Wy Leeward Wy Windward
Page 9 of 15
29/12/2020
Page 10 of 15
29/12/2020
Page 11 of 15
29/12/2020
Direction = X + Eccentricity Y
Seismic Response
S
ZI
Seismic Coefficient, Ah [IS 6.4.2] g
A =
2R
Period Used W Vb
Direction
(sec) (kN) (kN)
X + Ecc. Y 0.542 216.5916 18.9518
Page 12 of 15
29/12/2020
Page 13 of 15
23/12/2020
Direction = Y + Eccentricity X
Seismic Response
S
ZI
Seismic Coefficient, Ah [IS 6.4.2] g
A =
2R
Period Used W Vb
Direction
(sec) (kN) (kN)
Y + Ecc. X 0.661 216.5916 15.5881
Page 14 of 15
23/12/2020
Page 15 of 15
LOAD CALCULATIONS
Job No. : Rev. No. :
Project : Date :
Clint : Designed by :
Description : LOADS APPLIED ON THE MAIN FRAME-1 Checked by :
Building Type =
Length (o/o) = 31.45 m
Width (o/o) = 11.23 m
Width module =
Bay spacing = 3.49 m
Clear eave height = 3.66 m
Max. eave height = 4.57 m
Roof slope (θ) = 9.25 ˚
DEAD LOAD (DL)
Wt. of sheet & purline = 20.00 Kg/m²
Dead Load (DL) = 0.200 KN/m²
COLLATERAL LOAD
Collateral Load on Rafter = 0.00 Kg/m² Other Collateral Load = 0.00 Kg/m²
= 0.00 KN/m = 0.00 KN/m
PRESURE COEFFICIENTS:~
Encloser condition of the building = Enclosed
Internal pressure coeff.(Cpi) = 0.20
h/w = 0.41
= h/w<=1/2
l/w = 2.80
= 3/2<=l/w<4
External pressure coeff.(Cpe) : Table 4 Table 5
Wind Angle
Coeff. For Wall Coeff. For Roof
(ө)
Left Right Left Right
0 degree 0.70 -0.50 -1.20 -0.40
90 degree -0.60 0.70 -0.80 -0.60
Wind Across the Ridge (With -Ve Cpi) Wind Across the Ridge (With +Ve Cpi) KN/m
-1.00 -3.83 KN/m -0.20 -0.77KN/m -1.40 -5.368 KN/m -0.60 -2.30
KN/m KN/m
-3.07 1.92
-0.80 0.50
KN/m KN/m
-1.53 0.00
-0.40 0.90
Note:
1) Values within the circles are the UDL
2) -Ve value means, load applied
away from structure.
Current Date: 29/12/2020 16:05
Units system: SI
File name: C:\Users\ASUS\Desktop\d drive\pepsi mart truss\new works\BasePlate.rcnx\
Steel connections
Detailed report
______________________________________________________________________________________________________________________
________________________________________________________________________________
GENERAL INFORMATION
Connector
MEMBERS
Column
Section : IS_SHS 113X113X4.5
Material : E 250 A
Longitudinal offset : 0 mm
CONNECTOR
Base plate
Connection type : Unstiffened
Position on the support : Center
N: Depth : 450 mm
D: Gross width : 450 mm
tp: Thickness : 18 mm
Material : E 250 A
Column weld : E 41
s: Column weld size : 3 mm
Override A1/A2 ratio : No
Shear key type : None
Support
With pedestal : No
Longitudinal dimension : 450 mm
Transversal dimension : 450 mm
Thickness : 400 mm
Material : M40
Include grouting : No
Cover : 70 mm
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 2
Longitudinal edge distance on the plate : 75 mm
Transverse edge distance on the plate : 75 mm
Head type : Hexagonal
Include lock nut : Yes
Anchor : M-20
Effective embedment depth : 92 mm
Total length : 154.4 mm
Material : Class_4.8
Fy : 340 N/mm2
Fu : 400 N/mm2
Splitting Failure : No
Cracked concrete : No
Non-ductile steel : No
Fasteners welded to base plate : No
Lever arm : No
Anchor supplementary reinforcement
Tension reinforcement : No
Shear reinforcement : No
DEMANDS
Description Pu Mu22 Mu33 Vu2 Vu3
[KN] [KN*m] [KN*m] [KN] [KN]
-------------------------------------------------------------------------------
CM 53.53 8.02 -3.00 11.75 1.28
-------------------------------------------------------------------------------
Ratio 0.69
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Concrete base bearing [KN/mm2] 0.02 0.00 CM 0.00 IS 456 Cl. 34.4;
Base plate
Yielding at bearing interface [KN*m/m] 14.73 0.00 CM 0.00 Cl. 7.4.3.1
Yielding at tension interface [KN*m/m] 14.73 10.20 CM 0.69 Cl. 7.4.3.1
Column
Weld resistance [KN/m] 397.68 144.73 CM 0.36 Cl. 10.5.7.1.1
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Fasteners
Dimensions
Dimensions Unit Value Min. value Max. value Sta. References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fasteners
Spacing [mm] 300.00 80.00 -- [EC2-4] Sec. 7.2.2.5
Concrete cover [mm] 65.00 35.00 -- [EC2-1] Table 4.4N
Effective length [mm] 92.00 -- 387.00
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Steel failure of fastener in tension [KN] 85.21 18.38 CM 0.22 [3],
[EC2-4] Table 7.1
Pull-out failure of single fastener [KN] 109.96 18.38 CM 0.17 [EC2-4] Table 7.1
Concrete cone failure of single fastener [KN] 23.32 18.38 CM 0.79 [EC2-4] Eq. 7.13,
[EC2-4] Table 7.1
Concrete cone failure of group of fasteners [KN] 23.32 18.38 CM 0.79 [EC2-4] Eq. 7.13,
[EC2-4] Table 7.1
Steel failure of fastener in shear [KN] 51.12 2.94 CM 0.06 [EC2-4] Sec. 7.2.2.3.1
Pry-out failure of single fastener [KN] 46.63 2.94 CM 0.06 [EC2-4] Eq. 7.13,
[EC2-4] Table 7.1
Pry-out failure of group of fasteners [KN] 46.63 2.94 CM 0.06 [EC2-4] Eq. 7.13,
[EC2-4] Table 7.1
Concrete edge failure of single fastener [KN] 9.72 2.94 CM 0.30 [EC2-4] Eq. 7.39,
[EC2-4] Table 7.2
Concrete edge failure of group of fasteners [KN] 29.39 11.75 CM 0.40 [EC2-4] Eq. 7.39,
[EC2-4] Table 7.2
Combined tension and shear interaction for steel failure 1.00 0.05 CM 0.05 [EC2-4] Eq. 7.53
Combined tension and shear interaction for other modes 1.00 0.95 CM 0.95 [EC2-4] Eq. 7.54
Combined tension and shear interaction for other modes 1.20 1.19 CM 0.99 [EC2-4] Eq. 7.55
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.99
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (CM)
-----------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 18.38 [KN]
Minimum anchor tension 8.38 [KN]
Neutral axis angle 0.00
Bearing length -176.61 [mm]
-----------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [KN] [KN]
-----------------------------------------------------------------------------
1 -150.00 -150.00 2.94 18.38
2 -150.00 150.00 2.94 8.38
3 150.00 150.00 2.94 8.38
4 150.00 -150.00 2.94 18.38
-----------------------------------------------------------------------------
Major axis
Results for tensile breakout (CM)
REFERENCES
[EC2-4] EN 1992-4 (2013) Eurocode 2: Design of concrete structures - Part 4: Design of fastenings for use in concrete.
[EC2-1] EN 1992-1-1 (2004) Eurocode 2. Design of concrete structures - Part 1-1: General rules and rules for buildings
[3] International Federation for Structural Concrete (2011). Design of Anchorages in Concrete. CEP-FIP. Lousanne, Switzerland.
REINFORCED CONCRETE
Project
COUNCIL
Client Made by Date Page
Location Corner Footing A1 C1 A10 C10 Single column
base Checked Revision Job No
-
DIMENSIONS mm
BASE COLUMN
L = 1500 h = 450
B = 1500 b = 450
depth H = 1500
ex = 225 ey = 225
v yy 0%
REINFORCEMENT . .
Mxx = 3.9 kNm Myy = 3.9 kNm
b = 1500 mm b = 1500 mm
d = 1437.5 mm d = 1412.5 mm
As = 6 mm² As = 6 mm²
PROVIDE 6 T25 @ 275 B1 PROVIDE 6 T25 @ 275 B2
As prov = 2945 mm² As prov = 2945 mm²
. .
BEAM SHEAR . .
Vxx = 0.0 kN at d from col face Vyy = 0.0 kN at d from col face
v = 0.000 N/mm² v= 0.000 N/mm²
or Vxx = 0.0 kN at 2d from col face or Vyy = 0.0 kN at 2d from col face
v = 0.000 N/mm² v= 0.000 N/mm²
vc = 0.325 N/mm² vc = 0.327 N/mm²
PUNCHING SHEAR . .
d ave = 1425 mm u crit = 0 mm
As prov = 0.138 % v max = 0.047 N/mm² at col face
v = 0.000 N/mm² vc = 0.326 N/mm²
REINFORCED CONCRETE
Project
COUNCIL
Client Made by Date Page
Location Footing A2 to A9, C2 ,C3 Single column
base Checked Revision Job No
-
DIMENSIONS mm
BASE COLUMN
L = 1500 h = 450
B = 1500 b = 450
depth H = 1500
ex = 525 ey = 0
v yy 0%
REINFORCEMENT . .
Mxx = 193.3 kNm Myy = 4.1 kNm
b = 1500 mm b = 1500 mm
d = 1437.5 mm d = 1412.5 mm
As = 297 mm² As = 6 mm²
PROVIDE 6 T25 @ 275 B1 PROVIDE 6 T25 @ 275 B2
As prov = 2945 mm² As prov = 2945 mm²
. .
BEAM SHEAR . .
Vxx = 149.1 kN at d from col face Vyy = 0.0 kN at d from col face
v = 0.069 N/mm² v= 0.000 N/mm²
or Vxx = 149.1 kN at 2d from col face or Vyy = 0.0 kN at 2d from col face
v = 0.069 N/mm² v= 0.000 N/mm²
vc = 0.325 N/mm² vc = 0.327 N/mm²
PUNCHING SHEAR . .
d ave = 1425 mm u crit = 0 mm
As prov = 0.138 % v max = 0.054 N/mm² at col face
v = 0.000 N/mm² vc = 0.326 N/mm²
REINFORCED CONCRETE
Project
COUNCIL
Client Made by Date Page
Location Footing C4 to C9 Single column
base Checked Revision Job No
-
DIMENSIONS mm
BASE COLUMN
L = 1500 h = 450
B = 1500 b = 450
depth H = 1500
ex = 0 ey = 0
v yy 0%
REINFORCEMENT . .
Mxx = 4.0 kNm Myy = 4.0 kNm
b = 1500 mm b = 1500 mm
d = 1437.5 mm d = 1412.5 mm
As = 6 mm² As = 6 mm²
PROVIDE 6 T25 @ 275 B1 PROVIDE 6 T25 @ 275 B2
As prov = 2945 mm² As prov = 2945 mm²
. .
BEAM SHEAR . .
Vxx = 0.0 kN at d from col face Vyy = 0.0 kN at d from col face
v = 0.000 N/mm² v= 0.000 N/mm²
or Vxx = 0.0 kN at 2d from col face or Vyy = 0.0 kN at 2d from col face
v = 0.000 N/mm² v= 0.000 N/mm²
vc = 0.325 N/mm² vc = 0.327 N/mm²
PUNCHING SHEAR . .
d ave = 1425 mm u crit = 0 mm
As prov = 0.138 % v max = 0.053 N/mm² at col face
v = 0.000 N/mm² vc = 0.326 N/mm²
ETABS 18.0.2 License #*12KLFLD63HHJXJ7
Section Properties
A (cm²) Izz (cm⁴) rzz (mm) Ze,zz (cm³) Av,z (cm²) Zp,zz (cm³) Iyz (cm⁴) It (cm⁴)
6.3 21.4 18.5 8.7 3.1 8.7 0 35.8
J (cm⁴) Iyy (cm⁴) ryy (mm) Ze,yy (cm³) Av,y (cm²) Zp,yy (cm³) Iw (cm⁶) h (mm)
35.8 21.4 18.5 8.7 3.1 8.7 49.5
Material Properties
J (cm⁴) Iyy (cm⁴) ryy (mm)
35.8 21.4 18.5
Basic Factors
Buckling Mode K Factor L Factor L Length (mm) KL/r
Major (z-z) 1.454 0.932 851.8 67.076
Major Braced 0.655 0.932 851.8 30.21
Minor (y-y) 2.54 0.932 851.8 117.139
Minor Braced 0.817 0.932 851.8 37.682
LTB 2.54 0.932 851.8 117.139
α2
1.661
Shear Design
V Force (kN) Vd Capacity (kN) To Capacity (kN-m) Stress Ratio Status Check
Major (y) 2.385E-05 41.2018 4.205E-06 0 OK
Minor (z) 0.1111 41.2018 4.205E-06 0.003 OK
Shear Design
Vp (kN) kv (Unitless) ΛW (Unitless) Τb (MPa)
Reduction 41.2018 0 0 1
Section Properties
A (cm²) Izz (cm⁴) rzz (mm) Ze,zz (cm³) Av,z (cm²) Zp,zz (cm³) Iyz (cm⁴) It (cm⁴)
6.3 21.4 18.5 8.7 3.1 8.7 0 35.8
J (cm⁴) Iyy (cm⁴) ryy (mm) Ze,yy (cm³) Av,y (cm²) Zp,yy (cm³) Iw (cm⁶) h (mm)
35.8 21.4 18.5 8.7 3.1 8.7 49.5
Material Properties
J (cm⁴) Iyy (cm⁴) ryy (mm)
35.8 21.4 18.5
Basic Factors
Buckling Mode K Factor L Factor L Length (mm) KL/r
Major (z-z) 1 0.986 3444.1 186.486
Major Braced 1 0.986 3444.1 186.486
Minor (y-y) 1 0.986 3444.1 186.486
Minor Braced 1 0.986 3444.1 186.486
LTB 1 0.986 3444.1 186.486
Moment Designs
M Moment Mspan Moment Md(yield) Capacity Mdv Capacity Mnd Capacity Md(LTB) Capacity
kN-m kN-m kN-m kN-m kN-m kN-m
Major (z-z) -0.0973 -0.0973 1.9659 1.9659 1.9659 1.9659
Minor (y-y) 0.0036 0.0046 1.9659 1.9659 1.9659
Shear Design
V Force (kN) Vd Capacity (kN) To Capacity (kN-m) Stress Ratio Status Check
Major (y) 0.1254 41.2018 6.1E-07 0.003 OK
Minor (z) 0.0003 41.2018 6.1E-07 6.946E-06 OK
Shear Design
Vp (kN) kv (Unitless) ΛW (Unitless) Τb (MPa)
Reduction 41.2018 0 0 1
Section Properties
A (cm²) Izz (cm⁴) rzz (mm) Ze,zz (cm³) Av,z (cm²) Zp,zz (cm³) Iyz (cm⁴) It (cm⁴)
22.6 432.6 43.8 76.2 11.3 76.2 0 700.5
J (cm⁴) Iyy (cm⁴) ryy (mm) Ze,yy (cm³) Av,y (cm²) Zp,yy (cm³) Iw (cm⁶) h (mm)
700.5 432.6 43.8 76.2 11.3 76.2 113.5
Material Properties
J (cm⁴) Iyy (cm⁴) ryy (mm)
700.5 432.6 43.8
Basic Factors
Buckling Mode K Factor L Factor L Length (mm) KL/r
Major (z-z) 1 0.99 5556.1 126.997
Major Braced 1 0.99 5556.1 126.997
Minor (y-y) 1 1.98 11112.3 253.994
Minor Braced 1 1.98 11112.3 253.994
LTB 1 1.98 11112.3 253.994
α2
1.679
Shear Design
V Force (kN) Vd Capacity (kN) To Capacity (kN-m) Stress Ratio Status Check
Major (y) 0.1671 148.274 0.0078 0.001 OK
Minor (z) 0.0323 148.274 0.0078 2.18E-04 OK
Shear Design
Vp (kN) kv (Unitless) ΛW (Unitless) Τb (MPa)
Reduction 148.274 0 0 1
Section Properties
A (cm²) Izz (cm⁴) rzz (mm) Ze,zz (cm³) Av,z (cm²) Zp,zz (cm³) Iyz (cm⁴) It (cm⁴)
4.7 25.2 23.1 7.6 1.6 7.6 0 21
J (cm⁴) Iyy (cm⁴) ryy (mm) Ze,yy (cm³) Av,y (cm²) Zp,yy (cm³) Iw (cm⁶) h (mm)
21 8.4 13.4 5.1 3.1 5.1 66
Material Properties
J (cm⁴) Iyy (cm⁴) ryy (mm)
21 8.4 13.4
Basic Factors
Buckling Mode K Factor L Factor L Length (mm) KL/r
Major (z-z) 1 0.2 1137.4 49.168
Major Braced 1 0.2 1137.4 49.168
Minor (y-y) 1 0.2 1137.4 84.926
Minor Braced 1 0.2 1137.4 84.926
LTB 1 0.2 1137.4 84.926
Moment Designs
M Moment Mspan Moment Md(yield) Capacity Mdv Capacity Mnd Capacity Md(LTB) Capacity
kN-m kN-m kN-m kN-m kN-m kN-m
Major (z-z) 0.2987 0.2987 1.7318 1.7318 1.4053 1.7318
Minor (y-y) -4.628E-05 -0.0001 1.1614 1.1614 0.8451
Shear Design
V Force (kN) Vd Capacity (kN) To Capacity (kN-m) Stress Ratio Status Check
Major (y) 0.3402 41.1143 0.0027 0.008 OK
Minor (z) 0.0001 20.5572 0.0027 0 OK
Shear Design
Vp (kN) kv (Unitless) ΛW (Unitless) Τb (MPa)
Reduction 41.1143 0 0 1
Section Properties
A (cm²) Izz (cm⁴) rzz (mm) Ze,zz (cm³) Av,z (cm²) Zp,zz (cm³) Iyz (cm⁴) It (cm⁴)
20.3 393.3 44 69.3 10.1 69.3 0 631.1
J (cm⁴) Iyy (cm⁴) ryy (mm) Ze,yy (cm³) Av,y (cm²) Zp,yy (cm³) Iw (cm⁶) h (mm)
631.1 393.3 44 69.3 10.1 69.3 113.5
Material Properties
J (cm⁴) Iyy (cm⁴) ryy (mm)
631.1 393.3 44
Basic Factors
Buckling Mode K Factor L Factor L Length (mm) KL/r
Major (z-z) 1.542 0.969 3544.1 124.114
Major Braced 0.7 0.969 3544.1 56.363
Minor (y-y) 1.993 0.969 3544.1 160.416
Minor Braced 0.774 0.969 3544.1 62.313
LTB 1.993 0.969 3544.1 160.416
α2
1.679
Shear Design
V Force (kN) Vd Capacity (kN) To Capacity (kN-m) Stress Ratio Status Check
Major (y) 3.2202 133.0529 0.0222 0.024 OK
Minor (z) 0.0157 133.0529 0.0222 1.177E-04 OK
Shear Design
Vp (kN) kv (Unitless) ΛW (Unitless) Τb (MPa)
Reduction 133.0529 0 0 1
1 Structure Data
This chapter provides model geometry information, including items such as story levels, point coordinates, and
element connectivity.
Page 2 of 20
Loads 29/12/2020
2 Loads
This chapter provides loading information as applied to the model.
2.1 Functions
2.1.1 Response Spectrum Functions
Page 3 of 20
Analysis Results 29/12/2020
3 Analysis Results
This chapter provides analysis results.
Page 4 of 20
Analysis Results 29/12/2020
Page 6 of 20
Analysis Results 29/12/2020
Page 8 of 20
Analysis Results 29/12/2020
Page 9 of 20
Analysis Results 29/12/2020
Page 10 of 20
Analysis Results 29/12/2020
Page 13 of 20
Analysis Results 29/12/2020
Page 14 of 20
Analysis Results 29/12/2020
Page 16 of 20
Analysis Results 29/12/2020
Page 17 of 20
Analysis Results 29/12/2020
Page 18 of 20
Analysis Results 29/12/2020
Frequenc Eigenvalu
Period CircFreq
Case Mode y e
sec rad/sec
cyc/sec rad2/sec2
Modal 2 0.542 1.846 11.598 134.5131
Modal 3 0.497 2.011 12.6345 159.6315
Modal 4 0.081 12.361 77.6693 6032.5269
Modal 5 0.08 12.434 78.1226 6103.1344
Modal 6 0.079 12.584 79.0681 6251.7631
Modal 7 0.078 12.787 80.341 6454.6795
Modal 8 0.077 12.971 81.5022 6642.6107
Modal 9 0.073 13.771 86.5235 7486.3158
Modal 10 0.072 13.82 86.8335 7540.0625
Modal 11 0.072 13.944 87.6118 7675.835
Modal 12 0.072 13.971 87.7845 7706.1158
Page 19 of 20
Analysis Results 29/12/2020
Period
Case Mode UX UY UZ RZ
sec
Modal 7 0.078 0 0.654 0 0.346
Modal 8 0.077 0 0.026 0 0.974
Modal 9 0.073 0 0.579 0 0.421
Modal 10 0.072 0 0.02 0 0.98
Modal 11 0.072 0 0.999 0 0.001
Modal 12 0.072 0 0.387 0 0.613
Page 20 of 20