Professional Documents
Culture Documents
Parameter Settings
T-code Valid from serial number
483,484,657,658,793,794 709569-
Date Order number
2004-09-20 217166-040
1- 84 © BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Anders-
Electronic card – 5710
Parameter Settings
Valid from serial number T-code
709569- 483,484,657,658,793,794
Order number Date
217166-040 2004-09-20
© BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Andersson 1- 85
Electronic card – 5710
Parameter Settings
T-code Valid from serial number
483,484,657,658,793,794 709569-
Date Order number
2004-09-20 217166-040
1.5.1 Parameter 1
The higher the number you program, the less number of turns of the
steering wheel required to turn the drive wheel. With a value of 6, steer-
ing is non-progressive, less sensitive at higher speeds.
1.5.2 Parameter 2
This parameter sets the maximum permitted driving speed.
1.5.3 Parameter 3
The lower the number you program, the longer the truck will require to
come up to maximum speed.
1- 86 © BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Anders-
Electronic card – 5710
Parameter Settings
Valid from serial number T-code
709569- 483,484,657,658,793,794
Order number Date
217166-040 2004-09-20
1.5.4 Parameter 4
This parameter determines the force at which the truck will stop when
you release the accelerator pedal.
Note 1: Driver 1 has 20%, drivers 2-10 have 50% as the default value.
1.5.5 Parameter 5
With this parameter, you determine the force at which the truck will stop
when you change directions and use the drive motor to stop the truck.
1.5.6 Parameter 10
Value 0000 means that three drivers are chosen. The table below
shows the combinations for the first six PIN codes. These values are
attained by stepping up and down with the switches I and II.
1.5.7 Parameter 11
This parameter sets the maximum permitted driving speed when switch
S31 is activated.
1.5.8 Parameter 12
With this parameter you can adjust the speed of the mast’s in and out
movement.
1.5.9 Parameters 13 to 14
With this parameter you can adjust the oil flow for the two extra func-
tions.
© BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Andersson 1- 87
Electronic card – 5710
Parameter Settings
T-code Valid from serial number
483,484,657,658,793,794 709569-
Date Order number
2004-09-20 217166-040
1.5.12 Parameter 19
Lift height Coarse setting
M 16 mast with integrated side shift
4400 1,42
4600 1,50
4800 1,56
5400 1,75
5700 1,85
6300 2,07
6750 2,22
7000 2,42
7500 2,56
8000 2,74
8500 2,93
9000 3,09
9500 3,19
10000
10500
10800
1.5.13 Parameter 20
This parameter specifies the time A-d or S that will be displayed when
the driver uses the truck.
1- 88 © BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Anders-
Electronic card – 5710
Parameter Settings
Valid from serial number T-code
709569- 483,484,657,658,793,794
Order number Date
217166-040 2004-09-20
1.5.14 Parameter 21
With this parameter you specify the battery the truck is equipped with.
You may also compensate for different ways of driving.
For setting the battery monitor’s break point, measure as set out below:
• Acid density for fully charged battery. To check battery quality.
• When battery indicator shows 80% discharge, min. acid density 1.14.
The acid density can vary depending on the battery type.
15 480, 450
16
17 360
18
19
20
WARNING !
Correct parameter setting.
Battery can be destroyed.
If the parameters are set to values higher than those recommended,
battery discharge will be excessive and the batteries destroyed.
© BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Andersson 1- 89
Electronic card – 5710
Parameter Settings
T-code Valid from serial number
483,484,657,658,793,794 709569-
Date Order number
2004-09-20 217166-040
1.5.15 Parameter 23
When the parameter is set to 1 this defines that a valve is fitted to the
fork plank and is used as a switching valve between two functions.
Direction is handled by the valve in the large valve assembly.
1.5.16 Parameter 24
Set the parameter to 1 and you can stop the truck with the drive motor
but you cannot continue to drive, if the safety pedal is not depressed.
1.5.17 Parameter 25
With this parameter, you specify the truck’s service interval. The buzzer
sounds and C029 is shown on the display when the service counter is
at zero. The counter will show the time that has passed since the truck
was last serviced.
If the previous service time is to be used, only the parameter is activa-
ted the time is not changed.
1.5.18 Parameter 26
This parameter is used to set the maximum speed for the mast tilting.
1.5.19 Parameter 27
When the parameter is set to 1 this removes the lift function’s priority,
i.e. the hydraulic function being used will continue irrespective of
whether the lift is activated.
1.5.20 Parameter 28
This parameter allows information on the outputs 202 and 208 to be
switched between two different functions. 0 is for TLS and 1 is used to
start the warning light/buzzer when the truck is driven, an intermediate
relay must be used.
1.5.21 Parameter 29
When the truck is equipped with a height meter, you can specify the
maximum lifting height using this parameter. No bypass is possible. For
other information, see parameter 17 and 18.
1- 90 © BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Anders-
Electronic card – 5710
Parameter Settings
Valid from serial number T-code
709569- 483,484,657,658,793,794
Order number Date
217166-040 2004-09-20
1.5.22 Parameter 38
• Set the parameter to 1.
• Turn the ignition on and off once.
The acceleration and braking potentiometers will now be calibrated.
NOTE!
Calibration error.
Incorrect calibration value.
Do not move the lever when calibration begins.
• Retract the reach carriage towards the inner stop, battery partition.
• Move the reach carriage out to the outer stop.
The reach cylinder’s end position and lowering distance are now cali-
brated. The reach carriage’s movement will run at a reduced speed dur-
ing calibration.
1.5.23 Parameter 39
Set the parameter to 1 or 2 if only three drivers/truck profiles are to be
programmed. If up to ten drivers/truck profiles are to be programmed,
set the value to 3 or 4. With up to ten drivers, the value must be pro-
grammed for each driver. See parameter 10.
Show/programming choices with parameter 39.
Parame- Key S17 switched on, then Switch I and key S17 switched on
ter switch I simultaneously
P39- Clock Parameter Driver Clock Parameter Driver
-1 U. CAN Reprgm. See See selected Not reprgm. Reprgm. Selected
reprgm.
-1 M. CAN Reprgm. See See selected Not reprgm. Reprgm. All reprgm.
-2 U. CAN Reprgm. See See selected Not reprgm. Not reprgm. See
selected
-2 M. CAN Reprgm. See See selected Not reprgm. Reprgm. All reprgm.
-3 U. CAN Reprgm. See See selected Not reprgm. Reprgm. Selected
reprgm.
-3 M. CAN Reprgm. See See selected Not reprgm. Reprgm. All reprgm.
-4 U. CAN Reprgm. See See selected Not reprgm. Not reprgm. See
selected
-4 M. CAN Reprgm. See See selected Not reprgm. Reprgm. All reprgm.
© BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Andersson 1- 91
Electronic card – 5710
Parameter Settings
T-code Valid from serial number
483,484,657,658,793,794 709569-
Date Order number
2004-09-20 217166-040
1.5.24 Parameters 40 to 42
With these parameters you can set the year, day and month for error
code logging.
1- 92 © BT Europe AB Service Manual REFLEX RR M12, M14, M16Approved by: K-G Anders-