Professional Documents
Culture Documents
0 GTC-400EX LOAD CHART, With 4m Track Position, ISO, 3B6 PDF
0 GTC-400EX LOAD CHART, With 4m Track Position, ISO, 3B6 PDF
TABLE OF CONTENTS
LOAD CHART SELECTION & LOAD MOMENT INDICATOR SETTING INFORMATION ...................... 7
7. Boom positions without rated loads in the charts are prohibited. These areas are indicated by an “*” and are
susceptible to instability either in the forward direction or the backwards direction. Even without a load, the
boom should not be positioned in these specific configurations of the load chart to avoid tipping the crane.
8. Deductions from rated capacities must be made for the weight of the hook block, hook/ball, slings, spreader
bar, or other suspended equipment. This includes lifting accessories stowed on the boom such as jib,
extension, and auger
WINCHES/HOISTS
1. The Main (1) hoist is rated for a maximum 66.7 kN of line pull. Allowable line pull capacities must not be
exceeded under any circumstances. Therefore the minimum number of line reevings should be selected
based on the load to be lifted and entered in the RCI system.
2. The Optional Auxiliary (2) hoist is rated for a maximum 66.7 kN of line pull. Allowable line pull capacities
must not be exceeded under any circumstances. Therefore the minimum number of line reevings should be
selected based on the load to be lifted and entered in the RCI system.
3. Slack in the load rope should be avoided. Slack in the load rope can result in rope entanglement on the
hoist drum severely damaging the rope.
4. When retracting the boom telescopic sections, make sure the hook block does not come in contact with the
ground causing slack in the load rope.
6. Recommended reeving based on rated capacity; winch performance, wire rope length, and maximum
allowable rope tension are given at the bottom of each chart.
2. If the maximum rated capacity of the crane is exceeded by either exceeding the rated load or the rated load
radius, the RCI will shut down the following functions:
a. Boom Hoist DOWN
b. Boom Telescope EXTEND
c. Winch Hoist UP
Functions remaining operable are:
a. Boom Hoist UP
b. Boom telescope RETRACT
c. Winch Hoist DOWN
Correct operation of these shut downs should be verified before each instance of crane operation.
3. In order to ensure correct operation of the RCI system, the correct load chart (operating mode) must
selected in the RCI system, based upon counterweight configuration, tracks extended/ retracted condition,
and presence of other optional equipment.
4. The presence of the RCI system in no way removes the responsibility for safe lifting conditions from the
operator.
TMC# 99600147780 -5- Rev 0 12192016
MANTIS Model GTC-400EX LOAD CHART 32.0m BOOM
5. In order to provide the operator with an overview of the crane’s utilization and operating conditions, the RCI
system displays the following information:
a. Working radius
b. Maximum allowable lift capacity
c. Hook load
d. Boom height
e. Boom length
f. Boom Angle
g. Parts of line
h. Degree of load utilization
i. Selected load chart
j. Crane inclination
6. Limit switches are provide with the RCI system to prevent the hook block from coming in contact with the
boom head. Correct operation of these switches should be verified before each instance of crane operation.
7. Verification of correct operation of the RCI system is the responsibility of the crane operator and should be
performed before each instance of crane operation. Mantis Cranes will not accept liability for damage to the
crane and/or any consequential damage resulting from a non-functioning RCI system or deactivation of the
RCI system.
TRAVEL ALLOWED
COUNTER WEIGHT
TRACK POSITION
CONFIGURATION
(UP TO 1.0km/hr)
RCI OPERATION
PARTS OF LINE
LOAD CHART
OPERATING
(REEVING)
NUMBER
CRANE
LEVEL
MODE
Fully MAX. 8
1 Main Boom 6.8t NO 0° - 1° 1
Extended MIN. 1
Fully MAX. 8
1 Main Boom 6.8t NO 1° - 4° 2
Extended MIN. 1
Fully MAX. 8
1 Main Boom 6.8t YES 0° - 1° 3
Extended MIN. 1
Fully MAX. 8
1 Main Boom 6.8t YES 1° - 4° 4
Extended MIN. 1
Fully MAX. 8
2 Main Boom 0t NO 0° - 1° 5
Extended MIN. 1
Fully MAX. 8
2 Main Boom 0t NO 1° - 4° 6
Extended MIN. 1
Fully MAX. 8
2 Main Boom 0t YES 0° - 1° 7
Extended MIN. 1
Fully MAX. 8
2 Main Boom 0t YES 1° - 4° 8
Extended MIN. 1
MAX. 8
3 Main Boom 6.8t Retracted NO 0° - 1° 9
MIN. 1
MAX. 8
3 Main Boom 6.8t Retracted YES 0° - 1° 10
MIN. 1
Partial
MAX. 8
17 Main Boom 6.8t Extension NO 0° - 1° 11
MIN. 1
(4m)
Partial
MAX. 8
17 Main Boom 6.8t Extension NO 1° - 4° 12
MIN. 1
(4m)
Partial
MAX. 8
17 Main Boom 6.8t Extension YES 0° - 1° 13
MIN. 1
(4m)
Partial
MAX. 8
17 Main Boom 6.8t Extension YES 1° - 4° 14
MIN. 1
(4m)
Auxiliary
Fully
18 Boom Nose 6.8t MAX. 1 NO 0° - 1° 15
Extended
Sheave
TRAVEL ALLOWED
COUNTER WEIGHT
TRACK POSITION
CONFIGURATION
(UP TO 1.0km/hr)
RCI OPERATION
PARTS OF LINE
LOAD CHART
OPERATING
(REEVING)
NUMBER
CRANE
LEVEL
MODE
Auxiliary
Fully
18 Boom Nose 6.8t MAX. 1 NO 1° - 4° 16
Extended
Sheave
Auxiliary
Fully
18 Boom Nose 6.8t MAX. 1 YES 0° - 1° 17
Extended
Sheave
Auxiliary
Fully
18 Boom Nose 6.8t MAX. 1 YES 1° - 4° 18
Extended
Sheave
Auxiliary
Fully
19 Boom Nose 0t MAX. 1 NO 0° - 1° 19
Extended
Sheave
Auxiliary
Fully
19 Boom Nose 0t MAX. 1 NO 1° - 4° 20
Extended
Sheave
Auxiliary
Fully
19 Boom Nose 0t MAX. 1 YES 0° - 1° 21
Extended
Sheave
Auxiliary
Fully
19 Boom Nose 0t MAX. 1 YES 1° - 4° 22
Extended
Sheave
Auxiliary
32 Boom Nose 6.8t Retracted MAX. 1 NO 0° - 1° 23
Sheave
Auxiliary
32 Boom Nose 6.8t Retracted MAX. 1 YES 0° - 1° 24
Sheave
Auxiliary Partial
33 Boom Nose 6.8t Extension MAX. 1 NO 0° - 1° 25
Sheave (4m)
Auxiliary Partial
33 Boom Nose 6.8t Extension MAX. 1 NO 1° - 4° 26
Sheave (4m)
Auxiliary Partial
33 Boom Nose 6.8t Extension MAX. 1 YES 0° - 1° 27
Sheave (4m)
Auxiliary Partial
33 Boom Nose 6.8t Extension MAX. 1 YES 1° - 4° 28
Sheave (4m)
9.1m
Fully MAX. 2
34 Lattice 6.8t NO 0° - 1° 29
Extended MIN. 1
Extension
TRAVEL ALLOWED
COUNTER WEIGHT
TRACK POSITION
CONFIGURATION
(UP TO 1.0km/hr)
RCI OPERATION
PARTS OF LINE
LOAD CHART
OPERATING
(REEVING)
NUMBER
CRANE
LEVEL
MODE
6.1m Jib
+9.1m
Fully
35 Lattice 6.8t MAX. 1 NO 0° - 1° 30
Extended
Extension
0° Offset
6.1m Jib
+9.1m
Fully
49 Lattice 6.8t MAX. 1 NO 0° - 1° 30
Extended
Extension
15° Offset
6.1m Jib
+9.1m
Fully
50 Lattice 6.8t MAX. 1 NO 0° - 1° 30
Extended
Extension
30° Offset
9.1m
Fully MAX. 2
34 Lattice 6.8t YES 0° - 1° 31
Extended MIN. 1
Extension
6.1m Jib
+9.1m
Fully
35 Lattice 6.8t MAX. 1 YES 0° - 1° 32
Extended
Extension
0° Offset
6.1m Jib
+9.1m
Fully
49 Lattice 6.8t MAX. 1 YES 0° - 1° 32
Extended
Extension
15° Offset
6.1m Jib
+9.1m
Fully
50 Lattice 6.8t MAX. 1 YES 0° - 1° 32
Extended
Extension
30° Offset
Hookblocks
40.8 t - 4 Sheave 495 kg
10.9 t Overhaul Ball w/Swivel 180 kg
NOTE:
All values shown apply to original equipment as supplied by
Tadano Mantis Corporation. Deductions should be taken into
account when calculating the load to be lifted. Always use actual
weight for any rigging.
A properly calibrated and maintained Rated Capacity Indicator
(RCI) system will indicate boom mounted and other suspended
equipment.
CHART #2
NO TRAVEL – LEVEL 1°TO 4°
MAIN BOOM with TRACKS FULLY EXTENDED
6.8t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #3
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0°TO 1°
CHART #4
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 1°TO 4°
CHART #5
NO TRAVEL – LEVEL 0°TO 1°
MAIN BOOM with TRACKS FULLY EXTENDED
0t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #6
NO TRAVEL – LEVEL 1° TO 4°
MAIN BOOM with TRACKS FULLY EXTENDED
0t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #7
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0° TO 1°
MAIN BOOM with TRACKS FULLY EXTENDED
0t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #8
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 1° TO 4°
CHART #9
NO TRAVEL – LEVEL 0° TO 1°
MAIN BOOM with TRACKS RETRACTED
6.8t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #10
TRAVEL SPEEDS UP TO 1.4 km/h– LEVEL 1° TO 0°
MAIN BOOM with TRACKS RETRACTED
6.8t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #11
NO TRAVEL – LEVEL 0°TO 1°
MAIN BOOM with TRACKS PARTIALLY EXTENDED (4m)
6.8t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #12
NO TRAVEL – LEVEL 1°TO 4°
MAIN BOOM with TRACKS PARTIALLY EXTENDED (4m)
6.8t COUNTERWEIGHT
RADIUS MAIN BOOM LENGTH (m) RADIUS
(m) 10.4 12.8 15.2 17.6 21.2 24.8 28.4 32.0 (m)
CHART #13
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0°TO 1°
CHART #14
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 1°TO 4°
CHART #15
NO TRAVEL – LEVEL 0° TO 1°
CHART #16
NO TRAVEL – LEVEL 1° TO 4°
CHART #17
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0° TO 1°
CHART #18
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 1° TO 4°
CHART #19
NO TRAVEL – LEVEL 0° TO 1°
CHART #20
NO TRAVEL – LEVEL 1° TO 4°
CHART #21
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0° TO 1°
CHART #22
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 1° TO 4°
CHART #23
NO TRAVEL – LEVEL 0° TO 1°
CHART #24
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0° TO 1°
CHART #25
NO TRAVEL – LEVEL 0° TO 1°
CHART #26
NO TRAVEL – LEVEL 1° TO 4°
CHART #27
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 0° TO 1°
CHART #28
TRAVEL SPEEDS UP TO 1.4 km/h – LEVEL 1° TO 4°
RANGE CHART
MANTIS Model GTC-400EX
as originally manufactured and equipped by Tadano Mantis Corporation.
51
30° 15°
48
45
42
39
36
33
30
Lifting Height (m)
27
24
21
18
15
12
3
36 33 30 9 6