Professional Documents
Culture Documents
p
tK
u
lo
a
c
d
M
s
n
m
ie
S
SOMATOM Sensation
CT
Replacements of Parts
syngo Aquisition Workplace
© Siemens AG 2003
The reproduction, transmission or use
of this document or its contents is not
permitted without express written
authority. Offenders will be liable for
damages. All rights, including rights
created by patent grant or registration
of a utility model or design, are
reserved.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise
authorized by Siemens or one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated
with or authorized by Siemens or one of its affiliates are directed to contact one of the
local offices of Siemens or one of its affiliates before attempting installation or service pro-
cedures.
Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Notice for this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2 _______ ICS___________________________________________________________ 11
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ICS towers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Options of ICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Field replaceable units of ICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Prerequisites for replacements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tools and auxiliary equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Documentation references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tower 7 - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Opening the casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Closing the casing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tower 8 - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Opening the casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Closing the casing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ICS tower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CD/ DVD recorder (Tower 5, 6 and 7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DVD recorder Tower 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Battery on motherbord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Dongle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Active cooling for console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installing the cooling unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Optional components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Ethernet switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Keyboard change for Towers 1, 2, 3, 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Keyboard change for Towers 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Keyboard change for Towers 6 and 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Keyboard change for Tower 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Create the BIOS CD / CD, DVD Firmware update CD. . . . . . . . . . . . . . . . . . . . . . . . 40
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Install BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
CD/DVD Firmware installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Correcting the drive letter of CD/DVD drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Computer equipment of IRS 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Field replaceable units of IRS 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cabinet overview and labeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Prerequisites for replacements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Tools and auxiliary equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Opening covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Acquisition, Image Reformatting and Recon Computer . . . . . . . . . . . . . . . . . . . . . . . . . 49
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
100MBit-, 1GBit-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
News: 1GBit-Switch kit from January 2004 onwards. . . . . . . . . . . . . . . . . . . . . . . . . 52
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
KVM switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Computer equipment of IRS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Field replaceable units of IRS 2, IRS 2c and IRS2F . . . . . . . . . . . . . . . . . . . . . . . . . 58
Location of components and labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Prerequisites for replacements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Tools and auxiliary equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Opening covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
AQP -, TCR -, REC1/2 - Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Installing correct BIOS and CMOS- settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Installing IRS Software, TCR tables and update GREC-FPGA version (if applicable)61
1GBit-Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Service Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
KVM switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Final steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Computer equipment of IRS 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Field replaceable units of IRS 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Location of components and labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Prerequisites for replacements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Tools and auxiliary equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Opening covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
TCR -, REC1/2/3 - Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Installing correct BIOS and CMOS- settings (only for IRS REC 1, 2 and 3) . . . . . . . 67
Installing IRS Software (and TCR- tables if applicable). . . . . . . . . . . . . . . . . . . . . . . 68
1GBit-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Service Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
KVM switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Final steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
WARNING [ hz_serdoc_F13G01U12M02 ]
Avoid accident and injury or damage of parts.
Risk of accident and injury!
¹ Read and observe the “General safety notes” and the
“Product-specific safety notes”.
WARNING [ hz_serdoc_F13G01U05M08 ]
Dangerous voltages may be present. The ON/OFF switch does not
disconnect the ICS/IES from the line voltage.
Risk of electric shock!
¹ Remove the power plug from the grounded power outlet.
WARNING [ hz_serdoc_F12G02U07M02 ]
The UPS contains its own energy source (batteries). The parts
supplied with UPS power (ICS/IES/IRS) may still have power even
when the UPS is not connected to an AC supply (power off sta-
tus).
Risk of electrical shock from the UPS!
¹ Switch off UPS power by switching off the relevant circuit
brakers.
¹ Secure the system against unintended switch-on (e.g.
block breaker against switching on and/or mark breaker
against switch on).
CAUTION [ hz_serdoc_F13G08U01M01 ]
CE conformity of system will no longer be valid when using other
parts than itemized in the spare parts catalogue.
Risk of damage or data loss!
¹ Only components itemized as assemblies in the spare
parts catalogue will be used.
WARNING [ hz_serdoc_F13G01U14M01 ]
Non-permissible or faulty manipulations or changes to the hard-
ware or software can cause system malfunctions. This can cause
injury and/or damage to the equipment.
Risk of accident and injury or damage!
¹ Do not manipulate or modify hardware.
¹ Use only original spare parts shown the spare parts cata-
logue.
¹ The use or installation of software not approved by Sie-
mens is strictly prohibited.
WARNING [ hz_serdoc_F13G01U12M01 ]
Failure to observe the guidelines specified in this document may
lead to serious injury or loss of life.
Risk of accident and/or injury!
¹ The guidelines contained in this document have to be
strictly followed.
CAUTION [ hz_serdoc_F13G01U02M01 ]
Only approved service tools should be used during replacement
and troubleshooting.
Risk of injury!
¹ Use only approved tools.
Overview 1.2
1 3 4
6
5
This document only describes the replacement of major parts of the Navigator. Compo-
nents such as keyboard, control box, mouse and connection cables are not covered.
Separate documentation is available for:
• Adjustment and Quality Assurance of the Monitors
• Installation of Options
ICS towers 0
Depending on the system and its delivery date, the following ICS towers can be found in
the field:
• 71 30 300 - ICS Tower 1
• 77 11 703 - ICS Tower 2
• 77 11 844 - ICS Tower 5A
• 88 79 418 - ICS Tower 6A
• 88 79 616 - ICS Tower 6S
• 88 79 566 - ICS Tower 7A
• 10 14 35 62 - ICS Tower 8A
Options of ICS 0
Depending on the system, the following options can be found in the field:
• Additional monitors
• MOD Dicom
• Desktop MOD
NOTE The field replaceable unit “ICS tower” does not contain any
optional component. When replacing the tower, the options from a
defective ICS have to be reinstalled to the new ICS tower.
Documentation references 0
NOTE Make sure, that the computer is switched off and that the power
plug and all other connections are removed.
1. Unscrew the two knurled screws (1) on the back of the casing.
1. Hook the side cover into the lower guide trail in the casing (1). Make sure that the side
cover is offset by approximately 2 cm (a).
Engage the top edge of the side cover on the casing.
Push the side cover as far as it will go in the direction of the arrow (2).
NOTE After replacing the parts and reattaching covers, make sure to
reconnect all ground cables!
NOTE Make sure, that the computer is switched off and that the power
plug and all other connections are removed.
1. Unscrew the locking bolt for the side cover on the rear panel of the casing.
NOTE After replacing the parts and reattaching covers, make sure to
reconnect all ground cables!
Preparation 0
• Supplementary documentation:
As there are differences for each individual tower (e.g. for opening the covers), please
refer to the detailed instructions and figures listed in “Installation of Options”.
In order to generate the backup and to install the software, refer to “Installation of Soft-
ware” (if requested).
Detailed cabling information (interconnections) can be found in “System Installation”.
• If possible, clarify whether patient data have to be saved.
• If possible, create an up-to-date software backup.
• If possible note data, e.g. host name, static SRS routes, auto reports, service key,
regional settings.
• Shut down the software and switch off the tower.
• Disconnect all cable connections at the rear.
• Remove the tower from its position and find an adequate working place for the follow-
ing steps:
• Remove the dongle.
• If installed, remove the optional components (refer to “Installation of Options”).
NOTE With the rollout of software version VB30 an upgrade kit for tower
6 and 7 is available. This upgrade kit include a memory extension
for the main memory from 2GB to 3GB. The following working
steps are necessary before you install the new tower.
For Tower 6: To deinstall the main memory extension kit perform the following working
steps.
• Remove the side cover of the tower according to (Opening the casing / p. 13)
• Remove the RAM memory (2 x 1GB modules) with the labeling 1GB. Both modules are
needed for the new tower.
• Take the old memory modules at the bottom inside of the computer housing and install
these two modules where the memory extension kit was installed.
• Close the side cover according to (Closing the casing / p. 14)
For Tower 7: To deinstall the main memory extension kit perform the following working
steps.
• Remove the side cover of the tower according to (Opening the casing / p. 13)
• Remove the RAM memory (2 x 512MB modules) with labeling 512MB. Both modules
are needed for the new tower.
Installing 0
For Tower 6: To install the main memory extension kit perform the following working steps.
• Only if all memory slots are equipped, remove two of the installed memory modules
(2x512 MB) starting from the left see (1 and 2/Fig. 11 / p. 19).
• Plug in the two previously deinstalled 1GB memory modules next to the modules
already installed.
• Put the removed modules into anti-static packing and sticky-tape the bag to the bottom
inside of the computer housing. The modules have to be returned with the tower, if it is
exchanged in future.
For Tower 7: To install the main memory extension kit perform the following working steps.
• Plug in the two deinstalled 512MB memory modules next to the modules already
installed (1 and 2/Fig. 12 / p. 20).
• Put the removed modules into anti-static packing and sticky-tape the bag to the bottom
inside of the computer housing. The modules have to be returned with the tower, if it is
exchanged in future.
NOTE After replacing the parts and reattaching all covers, make sure to
reconnect all ground cables!
• Power on.
• ICS tower 1 only: Perform the BIOS setup according to “Installation of Options”. Set
“Clear Chassis Intrusion” from [No] to [Yes].
NOTICE As a safety mechanism, the ICS tower 1 senses (and stores the
information) whether the covers have been opened as well as the
time when the computer was switched off.
¹ If you attempt to perform the procedure without the cov-
ers installed, the following message appears “Warn-
ing!! Your computer chassis has been opened”
and the bootup sequence is stoppe
• ICS tower 6 with VB30 only: Perform a BIOS installation according to chapter (BIOS
installation / p. 40)
• Reboot the system.
• Install the software according to the current “Installation of Software”.
• Restore the backup (this will also restore the available licenses)
Final steps 0
Prerequisites 0
Preliminary steps 0
NOTE The cable length of the LCD panel is long enough so that you can
carefully place it to one side with the front panel. you do not need
to unplug the cable before removing the front panel.
Removing 0
Installing 0
1. Check the jumpers of the new CD/ DVD drive. It must be jumpered as “Master”. Cor-
rect, if required.
2. Lay the rails onto the new CD/ DVD recorder such that the holes in them align with the
screw holes (1).
3. Fasten the rails with the screws (2).
Start up 0
2. Close the right side cover according to (Closing the casing / p. 14)
Final steps 0
1. Power on.
2. Reboot the system.
3. Perform the firmware update according to (CD/DVD Firmware installation / p. 42) to
ensure that the DVD recorder has the current firmware version.
4. Execute Tune CD Burning:
- Go to Local Service -> Utilities -> Tune CD Burning.
- Select Tune CD Burning for current hardware and click Go.
¹ A message is displayed: “Tune CD Burning for current hardware was selected.
This may take some minutes.”
- Click Yes.
¹ After Tune CD Burning is finished the message “Driver has been successfully
installed” is displayed.
- Select Home and reboot the system.
5. Test the DVD recorder by storing and reading data within the application software.
Prerequisites 0
Preliminary steps 0
NOTE The cable length of the LCD panel is long enough so that you can
carefully place it to one side with the front panel. you do not need
to unplug the cable before removing the front panel.
- Detach the three lockking tabs on the left side of the front panel (1).
- Fold open the front in the direction of the arrow (2).
- If necessary, detach the hinge on the right-hand side of the front panel from the cas-
ing and carefully remove the front panel.
Removing 0
Installing 0
1. Check the jumpers of the new DVD. It must be jumpered as “Master”. Correct, if
required.
1. Slide the new DVD recorder into the casing until it locks in position (1).
2. Connect all cables to the DVD recorder
3. Fasten the drive with the screws (2).
Start up 0
Final steps 0
1. Power on.
2. Reboot the system.
3. Perform the firmware update according to (CD/DVD Firmware installation / p. 42), to
make sure that the DVD recorder has the current firmware version.
4. Execute Tune CD Burning:
- Go to Local Service -> Utilities -> Tune CD Burning.
- Select Tune CD Burning for current hardware and click Go.
¹ A message pops up “Tune CD Burning for current hardware was selected. This
may take some minutes.”
- Click Yes.
¹ After Tune CD Burning is finished the message “Driver has been successfully
installed” appears.
NOTE This replacement of the battery is valid for ICS Tower 7 upwards.
Prerequisites 0
Preliminary steps 0
Removing 0
NOTE The lithium battery holder exists in different designs that function
in the same way.
Installing 0
• Push the new lithium battery into the holder (3) and press it downward until it engages
(4).
Start up 0
1. Power on.
2. Perform the BIOS installation according to (BIOS installation / p. 40)
Final steps 0
Dongle 2.8
Preparation 0
• When replacing the dongle, the corresponding new licenses have to be created and
implemented as well.
Installing 0
Final steps 0
Overview 0
For Tower 7 onward in combination with the console furniture an active cooling is neces-
sary because of the heat development.
Preparation
• Shut down and switch off the computers.
• Remove the metal covers.
• Deinstall the spacers. Take care not to drop the nut and washer when doing this.
• Connect the PE wire to an unused ground bolt at the multiple socket strip´s cover.
Concluding steps
• Install the metal covers.
• For information about replacing the Ethernet switch, refer to “System Installation”
and/or to “Installation of Options”.
• Short summary of BIOS installation process: Insert CD- ROM, power up the PC, wait
some minutes.
For a detailed description, see section “Installation of BIOS”
• Disconnect the old keyboard
• Connect the new keyboard.
Download the necessary BIOS file from the intranet. Navigate to “http://cs.med.sie-
mens.de/cms/en/home/default.asp“ and follow path “For Service > Product Information >
CT Systems > Software download“.
(Software download, https://cs.med.siemens.de/cms/productinfo/default.asp?start-
folder=8bd95977e70107fde60d2a5aeebc0049)
Download the BIOS / CD, DVD Firmware file:
• In the “CT-Software Update Page“, left-click the file to be downloaded.
• Save the file to the hard drive c:\temp. When finished, close the window.
Label a blank CD-R/FD with the file name of the downloaded file:
• For ICS and IES Tower 5, e.g., “10141460 VA01A Tower5 CS”
• For ICS and IES Tower 6, e.g., “10142438 VA01A Tower6 CS”
• For ICS and IES Tower 7, e.g., “10142439 VA01B Tower7 CS“
• For ICS and IES Tower 8, e.g., “10143567 VA01D Tower8 CS“
NOTE Once the files are extracted to the CD, they must not be copied to
another CD for distribution (e.g. no CD-to-CD copies, as it cannot
be verified that the SW is virus-free).
Virus Check
After the CD is burned successfully, perform a virus scan of the CD after having updated
the virus scanning software with the latest versions of the virus patterns.
After you have performed the virus scan without any problems, the CD is ready and the
Bios update can be performed on the customer system.
Summary 0
Install BIOS 0
Worksteps:
• Insert the BIOS setup- CD, power the computer off, the power it up to reboot from CD.
Make sure to use the correct CD, see above for partnumbers.
• The computer boots from the setup-CD.
NOTE If the computer does not boot from CD, check the boot sequence in
the BIOS.
NOTE If the CD inserted is not designed for the computer type (e.g., a
Tower 5 CD is inserted into a Tower 6 model), the message “CD
not designed for this computer” appears.
• First, the screen shows the booting process of Windows 98, next the progress of the
hardware detection is displayed and then the BIOS is flashed.
If the system BIOS is already the current version, the installer will directly go to loading
the BIOS settings.
¹ The message "BIOS xxx flashed” indicates the success (xxx = version of the
BIOS, e.g.,”107” for “BIOS version 1.07”)
• The computer reboots from CDROM.
Next, the System BIOS Settings are loaded.
¹ The message “Operation completed successfully” indicates the
success.
• Then, the SCSI BIOS Settings are set.
¹ The message “Update of ***5* successful” indicates the success.
¹ The BIOS update is complete.
Worksteps:
• Insert the Firmware update CD, power the computer off, then power it up to reboot from
CD. To create the CD refer to (Create the BIOS CD / CD, DVD Firmware update
CD / p. 40).
Make sure to use the correct CD, see above for part numbers.
• A menu appears:
1 Leave Version<old#>
2 Update to version <new#> -Please check drive letter (see
"replacement of parts")
Select “1 ↵ ” to keep the prior firmware on the drive
or select “2 ↵ ” to update.
NOTE If the CD/DVD drive FW is updated, the drive letter has to be cor-
rected after the reboot.
“Windows plug and play” tries to assign the next free drive letter
instead of the letter R
See the following instructions.
The IRS 1 (73 94 617) cabinet comprises the following single computers
• 73 95 259 - AQP - Acquisition computer -CPU 1
• 73 95 275 - TCR - Image reformatting computer - CPU 2
• 73 95 267 - REC1,2 - Recon computer 1 and 2 - CPU 3 and CPU 4
NOTE The field replacable units of the IRS1 can be used with Windows
NT based SW- Versions (e.g., VA70) as well as with Windows XP
based SW- Versions (e.g., VB10) without modifying the BIOS of
the indivitual Computers (That step is exclusive for IRS2/IRS2c).
The cabinet is organized in rows from A to K and in columns from Mk to LA3. A schematic
drawing of the layout is located on the back of the front door.
According to the labeling, connectors refer to the physical location (refer to example
A-LA3 in (Fig. 26 / p. 45))
A-LA3
1
10
3
8 9
1
5
6
2
Cabling 0
From To
Location Component Location Switch
A-LA1 Recon Comp. 2 Row J Control, Port 1
B-LA1 Recon Comp. 1 Row J Control, Port 2
E-LA1 Image Reform. Comp. Row J Control, Port 3
F-LA1 Acquisition Comp. Row J Control, Port 4
E-LA3 Image Reform. Comp. Row J Control, Port 5
ICS Row J Control, Port 8
F-LA2 Acquisition Comp. Row G ACQ2RECON, Port 1
A-LA2 Recon Comp. 2 Row G ACQ2RECON, Port 2
B-LA2 Recon Comp. 1 Row G ACQ2RECON, Port 3
E-LA2 Image Reform. Comp. Row H RECON2REFORM, Port 1
A-LA3 Recon Comp. 2 Row H RECON2REFORM, Port 2
B-LA3 Recon Comp. 1 Row H RECON2REFORM, Port 3
From To
Location Component Location Component
A-KVM Recon Comp. 2 Row K KVM Switch, CPU 4
B-KVM Recon Comp. 1 Row K KVM Switch, CPU 3
E-KVM Image Reform. Comp. Row K KVM Switch, CPU 2
F-KVM Acquisition Comp. Row K KVM Switch, CPU 1
K-KVM KVM switch Row D Service Console
Opening covers 0
Most service activities can be performed from the front side of the cabinet.
Only the components of the current limiting are located at the back of the cabinet.
In some cases, opening back and/or side covers may ensure better access to parts and
components. It is especially useful to open the side cover when replacing cables.
Side covers
The side covers can be opened by pressing the red lever down (at the top) and up (at the
bottom) with a screwdriver.
NOTE Please note the ground connection inside the side covers.
Preliminary steps 0
Removing 0
1. Remove the four Phillips-head screws (shown in (1/Fig. 28 / p. 49) for Recon Com-
puter 2) and pull out computer system to provide access to the power plug in the back.
1 1
Installing 0
Final steps 0
From approx. January 2004 onwards the 1GBit-Switch, part no. 7395283, will not be avail-
able any more.
The 1GBit-Switch, part no. 7395283, will be replaced by the 1GBit-Switch kit, part no.
7541829.
Preliminary steps 0
2. Switch off system using the on-site ON/OFF switch or F5 within the PDC.
3. Disconnect all cables at the front side of the corresponding switch.
Removing 0
1. Remove the Phillips-head screws ((1/Fig. 30 / p. 53) for the 1GBit switch and
(2/Fig. 30 / p. 53) for the 100MBit switch) and pull out the switch to obtain access to the
power cable.
NOTE In case you have to replace one of the 1GBit switches, you have to
remove both switches.
1
1
2 2
Installing 0
1. Move new switch into the rack to obtain access to the power connection at the back side
of the switch.
2. Insert the power cable.
3. Move switch completely into rack.
4. Secure switch with the Phillips-head screws.
Final steps 0
Console 5.4
Preliminary steps 0
2. Switch off system using the on-site ON/OFF switch or F5 within the PDC.
Removing 0
Installing 0
1. Secure the new console with six Phillips-head screws at the guides.
2. Connect the monitor and power cables at the console.
3. Guide the keyboard and mouse cables back into position and connect them at the left
side of the IRS cabinet. Secure cables with cable ties.
4. Push console back into the cabinet.
Final steps 0
Preliminary steps 0
2. Switch off system using the on-site ON/OFF switch or F5 within the PDC.
Removing 0
1. Remove the four Phillips-head screws (1/Fig. 32 / p. 56) and pull out the KVM switch to
provide access to the power cable in the back.
1 1
Installing 0
1. Check the power-on switch at the back side of the KVM switch. Make sure that it is
switched to the ON position.
2. Move the new KVM switch into the rack to obtain access to the power connection at the
back side of the switch.
3. Insert the power cable.
4. Move the KVM switch completely into the rack.
5. Secure the KVM switch with four Phillips-head screws (1/Fig. 32 / p. 56).
Final steps 0
The IRS 2 (73 94 641) and IRS 2c (7542603) cabinet comprises the following single com-
puters:
• 73 94 658 - AQP - Acquisition computer - CPU 1
• 73 94 682 - TCR - Image reformatting computer - CPU 2
• 73 94 666 - REC1,2 - Recon computer 1/2 - CPU 3 and CPU 4
NOTE The IRS2c differs from the IRS2 only in the number of REC comput-
ers: IRS2 has 2 RECs, the IRS2c is only used for newer Sensation
10 and has 1 REC computer.
If the system has an IRS2 with 2 RECs, it is not possible to run it
with only 1 REC.
The IRS 2F cabinet (83 78 353) comprises the following single computers
• 83 78 361 - AQP
• 83 78 387 - TCR
• 83 78 379 - REC 1, REC 2
The cabinet is organized in rows from A to K and in columns from Mk to LA3. Find a sche-
matic drawing of the layout on the open front door.
All data cables are labeled with the connection points.
Opening covers 0
Most service activities can be performed from the front side of the cabinet.
Only the components of the current limiting are located at the back of the cabinet.
In some cases, opening back and/or side covers may ensure better access to parts and
components. It is especially useful to open the side cover when replacing cables.
Side covers
The side covers can be opened by pressing the red lever down (at the top) and up (at the
bottom) with a screwdriver.
NOTE Please note the ground connection inside the side covers.
Preparation 0
Removing 0
1. Remove the four Phillips-head screws and pull out the computer system to access the
rear.
2. Disconnect the power cable.
3. Remove the computer system from the cabinet.
Installing 0
Installing IRS Software, TCR tables and update GREC-FPGA version (if applica-
ble) 0
1. Install the IRS software of the corresponding computer according to “Installation of Soft-
ware”.
2. For IRS 2F and IRS AQP with SW version VB20 only:
Install GREC-FPGA version 3.7:
a) Insert the update CD into the CD drive on the IRS AQP.
b) An autostart is performed. Wait until the Command window pops up.
c) Press any key to continue
d) Wait until the update is finished
e) Remove update CD from the drive
3. Switch off the system at the control box.
4. Switch on the system again to synchronize ICS with IRS.
5. For Reformatting Computer TCR only:
Perform a restore of the IRS tables according to “Installation of Software”.
6. Perform test scans.
1GBit-Switch 6.3
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
2. Switch off the system using the on-site ON/OFF switch or F5 within the PDC.
3. Disconnect all cables at the front side of the corresponding switch.
Removing 0
1. Remove the Phillips-head screws and pull out the switch to obtain access to the rear.
2. Disconnect the power cables on the back side of the switch.
3. Remove the switch from the cabinet.
4. Exchange the angle brackets from the old switch with the new ones.
Installing 0
1. Move the new switch into the rack to obtain access to the power connection on the back
side of the switch.
2. Insert the power cable.
3. Move switch completely into rack.
4. Secure switch with the Phillips-head screws.
5. Connect all cables at the front side of the switch according to the labels.
Final steps 0
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
2. Switch off the system using the on-site ON/OFF switch or F5 within the PDC.
Removing 0
Installing 0
1. Secure the new console with six Phillips-head screws at the guides.
2. Connect the monitor and power cables at the console.
3. Guide the keyboard and mouse cables back into position and connect them at the left
side of the IRS cabinet. Secure the cables with cable ties.
4. Push the console back into the cabinet.
Final steps 0
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
2. Switch off the system using the on-site ON/OFF switch or F5 within the PDC.
Removing 0
1. Remove the four Phillips-head screws and pull out the KVM switch to access the rear.
2. Disconnect the power cable.
3. Remove the KVM switch from the cabinet.
Installing 0
1. Check the power-on switch at the back side of the KVM switch. Make sure that it is
switched to the ON position.
2. Move the new KVM switch into the rack to obtain access to the power connection on the
back side of the switch.
3. Insert the power cable.
4. Move the KVM switch completely into the rack.
5. Secure the KVM switch with four Phillips-head screws.
Final steps 0
The IRS 3 (83 77 785) cabinet comprises the following single computers:
• 83 77 793 - TCR - Image reformatting computer
• 83 77 694 - REC1,2,3 - Recon computer 1, 2 and 3
The cabinet is organized in rows from A to K and in columns from Mk to LA3. Find a sche-
matic drawing of the layout on the blanking plate.
All data cables are labeled with the connection points.
Opening covers 0
Most service activities can be performed from the front side of the cabinet.
Only the components of the current limiting are located in back of the cabinet.
In some cases, opening back and/or side covers may ensure better access to parts and
components. It is especially useful to open the side cover when replacing cables.
Side covers
The side covers can be opened with a coin or a large screwdriver.
NOTE Please note the ground connection inside the side covers.
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter.”
Removing 0
1. Remove the four Phillips head screws and pull out the computer system to access the
back.
2. Disconnect the power cable.
3. Remove the computer system from the cabinet.
Installation 0
Installing correct BIOS and CMOS- settings (only for IRS REC 1, 2 and 3) 0
1. Install the IRS software of the corresponding computer according to the “Installation of
Software.”
2. Switch off the system at the control box.
3. Switch on the system again to synchronize ICS with IRS.
4. For Reformatting Computer TCR only:
Perform a restore of the IRS tables according to the “Installation of Software.”
5. Perform test scans.
1GBit-Switch 7.3
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
Removing 0
1. Remove the Phillips-head screws and pull out the switch to obtain access to the rear.
2. Disconnect the power cables in back of the switch.
3. Remove the switch from the cabinet.
4. Replace the angle brackets from the old switch with the new ones.
Installation 0
1. Move the new switch into the rack to obtain access to the power connection in back of
the switch.
2. Insert the power cable.
3. Move switch completely into rack.
4. Secure switch with the Phillips-head screws.
5. Connect all cables at the front side of the switch according to the labels.
Final steps 0
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
Removing 0
Installation 0
1. Secure the new console with six Phillips-head screws at the guides.
2. Connect the monitor and power cables at the console.
3. Guide the keyboard and mouse cables back into position and connect them at the left
side of the IRS cabinet. Secure the cables with cable ties.
4. Push the console back into the cabinet.
Final steps 0
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
Removing 0
1. Remove the four Phillips-head screws and pull out the KVM switch to access the rear.
2. Disconnect the power cable.
3. Remove the KVM switch from the cabinet.
Installation 0
1. Check the power-on switch at the back side of the KVM switch. Make sure that it is
switched to the ON position.
2. Move the new KVM switch into the rack to obtain access to the power connection in
back of the switch.
3. Insert the power cable.
4. Move the KVM switch completely into the rack.
5. Secure the KVM switch with four Phillips-head screws.
Final steps 0
Fan 7.6
Preparation 0
1. Shut down the software application for the Wizard and the Navigator.
Click SYSTEM and select END in the main user menu.
Wait until the following message appears “It’s now safe to turn off the com-
puter”.
Removing 0
NOTE In the near future, each fan is attached with two screws.
Installation 0
NOTE The air flow is from the front to the back. Make sure that the cor-
rect fan is installed (refer to the labeling on the fan for air flow
direction).
Final steps 0
H
9Index
hz_serdoc_F12G02U07M02 . . . . . . . . .7
hz_serdoc_F13G01U02M01 . . . . . . . . .8
hz_serdoc_F13G01U05M08 . . . . . . . . .7
hz_serdoc_F13G01U12M01 . . . . . . . . .8
hz_serdoc_F13G01U12M02 . . . . . . . . .7
hz_serdoc_F13G01U14M01 . . . . . . . . .8
hz_serdoc_F13G08U01M01 . . . . . . . . .7