Professional Documents
Culture Documents
Lokfix E75 TDS 8072020
Lokfix E75 TDS 8072020
Description
■ Does not apply expansive force to the substrate ■ Émissions dans l’air intérieur : A+
■ Fixings can be spaced closer together than mechanical ■ LEED compliant VOC Level
anchors
■ Low VOC
■ Tested with diamond drilled bore holes
+5ºC 120 50
+10 ºC 90 30
+20 ºC 30 10
+30 ºC 20 6
+40ºC 12 4
Material Properties
Chemical resistance
Page 2
Fosroc® Lokfix E75
Design Criteria
Edge Distance Ccr,N 97 121 139 170 180 219 274 298 330 372 413
Min. Edge Distance 5xd Cmin 40 50 60 70 80 100 125 140 160 180 200
Axial Distance Scr,N 194 242 277 339 360 438 548 596 661 744 826
Min. Axial Distance 5xd Smin 40 50 60 70 80 100 125 140 160 180 200
mm
Embedment Depth hef 80 90 110 115 125 170 210 250 280 340 360
Drill Diameter d0 12 14 16 18 20 24 32 35 40 46 50
Brush Diameter 14 16 18 20 22 26 34 37 42 48 52
6 7 10 12 15 24 66 88 128 220 256
Material Consumption ml
Edge Distance Ccr,N 113 135 165 188 255 304 342 379 400 436 472
Min. Edge Distance 5xd Cmin 40 50 60 80 100 120 135 150 165 180 195
Axial Distance Scr,N 226 270 330 375 510 607 683 759 799 872 945
Min. Axial Distance 5xd Smin 40 50 60 80 100 120 135 150 165 180 195
mm
Embedment Depth hef 80 90 110 125 170 210 250 280 320 350 380
Drill Diameter d0 10 12 14 18 24 28 32 35 37 42 46
Brush Diameter 12 14 16 20 26 30 34 37 39 44 48
Installation Torque Tinst. Nm 10 20 40 60 120 150 200 250 350 500 700
3 4 5 7 24 35 58 72 71 130 180
Material Consumption ml
Note tables 3 and 4 are for dry un-cracked concrete only. For relevant method statement, EAD document or use the design
all other conditions including fixings into solid masonry types, software www.lokfix.com, also available through your local
fixings into cracked concrete, fixings subject to seismic condi- technical office.
tions and post installation of reinforcement, then refer to the
Page 3
Fosroc® Lokfix E75
Clean holes immediately prior to installation of fixings to the hole which indicates that there is full embedment.
avoid them becoming re-contaminated. Do not load or apply tension to the fixing until the product
Standing water in the hole shall be removed prior to prepara- fixing time has been observed, see table 2 .
tion. Using a hand pump or compressed air insert the nozzle Do not over-tighten fixings. Observe maximum installation
to the back of the hole and blow out 2 times. torque as stated in tables 3 & 4.
Insert a wire cleaning brush to the bottom of the hole and If the cartridge is to be re-used, remove the mixing nozzle
brush out 2 times and re-apply the cap. When using again a new mixing noz-
Using a hand pump or compressed air insert the nozzle to zle will be required.
the back of the hole and blow out an additional 2 times. Cleaning
If dust is still present, repeat the process until no further dust Wet resin should be removed from tools and equipment us-
is visible. ing Fosroc Solvent 102 immediately after use.
Ensure the drill bit and the cleaning brush are of suitable Estimating
diameter for the fixing used. Consult tables 3 and 4 for spe-
Supply
cific diameters.
Lokfix E75 supplied in boxes of 12 no. 385ml cartridges,
Fixings Preparation
each supplied with a single mixer nozzle.
Fixings shall be free from rust, paint, grease and contami-
Fosroc may also supply:
nants which will interfere with the bond.
■ Lokfix E75 application gun, one size.
Mark the required depth on the fixing.
■ Steel cleaning brushes, in various diameter to clean the
Installation
hole.
Lokfix E75 requires a special 3:1 application gun.
■ Dust blower pump, one size, hand held to clean the hole.
Unscrew the fixing cap. Remove the plastic stopper.
■ Hollow block sleeves, in a variety of diameters and em-
Screw the static mixer nozzle onto the cartridge. Place the bedded lengths for hollow bricks and blocks, can be
cartridge into the application gun. used for solid brick.
Page 4
Fosroc® Lokfix E75
■ Spare mixer nozzles, required if a cartridge is to be re- Lokfix E75 may stain natural or decorative stone. Suitability
used. must be checked before using for such applications.
Storage
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply
of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recommendation,
specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control over where or how its
products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or not in accordance with any
advice, specification, recommendation of information given by it.
Fosroc Limited
Drayton Manor Business Park telephone: fax: email:
Coleshill Road, Tamworth, +44 (0)1827 262222 +44 (0)1827 262444 enquiryuk@fosroc.com
Staffordshire B78 3XN. UK
www.fosroc.com
Page 5