Professional Documents
Culture Documents
6
PolyЯRon BONDIT SBR
Built to last
HPI/TDS/1912-6.6A
HP INDUSTRIES W.L.L
Street no.1,New Industrial Zone,Doha-Qatar, IAS0310Q1101
209
Dosage Mixing
The dosage rate of PolyЯRon BONDIT SBR will Small quantities may be mixed with a drill and "jiffy" mixer.
depend on kind of application. Use a paddle type mortar mixer for large jobs. Add the
appropriate amount of latex for the batch size and then
Additive for repair add the dry material. If using PolyЯRon BONDIT SBR with
15-20% by weight of cement
mortar a pre-packaged product, reduce the amount of water
Additive for hard added to compensate for the latex addition. Mix for a
16-18% by weight of cement
floor toping minimum of 3 minutes. The mixed product should be
Slurry coat 23% by weight of cement quickly transported to the repair area and placed
immediately.
Indicative mix design:
Note: This just an indicative design. Final Slurry application
design to be reached through trial and error Spread the slurry with a stiff bristle broom until the
depending on the availability of sand and suggested coverage rate has been achieved.
aggregates.
Application instructions Bond Coating Application
Surface preparation spread the slurry with a stiff bristle broom until the
Clean the surface to make it free from dust, oil, suggested coverage rate is achieved. When used for
loosely adhered particles, paint stains, bonding application slurry should be wet or tacky for the
efflorescence and other contaminations. The successive applications.
surface should be abraded or sanded
If PolyЯRon BONDIT SBR is used as a slurry Mix unit Cement mortar Topping
bond coat, ensure that concrete is 3 days old. slurry
Do not place slurry coat on standing water. cement kg 50 50 50
Ensure that the concrete is clean and rough. sand kg 125- 90
Remove all oil, dirt, debris, paint and unsound 150
concrete. The surface must be prepared 5mm kg 60
mechanically using a scabbler, bush hammer, aggregate
shot blast or scarifier which will give a surface Polyrron L 11.5 7.5-10 8-9
Built to last
profile of a minimum 3 mm and expose the large BONDIT
aggregate of the concrete. Use vacuum cleaner SBR
or pressure washing to ensure thorough water L 8-10 8-10 10-13
cleaning and removal of all residue. Ensure all
concrete possess an open surface texture with Topping Application
all curing compounds and sealers removed. For patching/topping, spread with a trowel, come-a-long,
Pre-wet all areas to reduce moisture loss or a square tipped shovel to a thickness that matches the
surrounding concrete. Finish by hand trowelling. On large
Bonding floor areas, use screed strips as guides in combination
For bonding toppings and other repair with vibratory screeding to level. Compact and finish by
mortars,we prefer to use the product in slurry hand or machine trowel.The topping should be placed
form rather than using the product itself as over the primed slurry coat to enhance the adhession
primer. After the surface has been prepared
prime all the areas using slurry coat and place Repair Mortar
the toppings /render/ mortar before the slurry The mixed material shall be applied on the primed area
dries out. using trowel and must be well compacted. In case of
Follow the individual mixing and placement repair applications, the repair thickness shall not be more
procedures listed below for applications. than 40mm. For larger thickness, apply in two lifts to build
up the thickness. Keep trowel clean and wet to prevent
sticking of material. Do not over trowel.
HPI/TDS/1912-6.6A
HP INDUSTRIES W.L.L
Street no.1,New Industrial Zone,Doha-Qatar, IAS0310Q1101
210
Finishing Fire
Finish the repair material to the desired texture. Non Flammable
Typical texture is a broom or sponge float finish.
Do not add additional water to the surface Health & safety
during the finishing operation. PolyЯRon BONDIT SBR should not come in contact with
skin. In case of contact with skin rinse with plenty of
Curing water, then cleanse thoroughly with soap and water. In
Proper curing procedures are important to case of contact with eyes rinse immediately with plenty of
ensure the durability and quality of the repair or clean water and seek medical advice. If swallowed seek
overlayment. To prevent surface cracking, a medical advice immediately-do not induce vomiting.
moist cure should be maintained for 24 hours Refer Material Safety Data Sheet for further details.
followed by use of a curing compound such as
PolyЯRon CURE AC. Do not use a solvent More from our product Range
based curing compound on latex modified
A Broad range of construction chemical products are
mortars.
manufactured by HP Industries under PolyЯRon brand
which include:
Cleaning • Concrete admixtures
Clean the equipments using water immediately
• Waterproofing and dampproof coatings
after use.Hardened material can be removed
• Bituminous coatings and Primers
only through Mechanical ways
• Surface treatments and releasing agents
• Floorings ,toppings and coatings
Packaging
• Protective coatings& sealers
PolyЯRon BONDIT SBR is available in 20 litre
• Tile glues ,block fixing agents & grouts
pails and 200 litre drums.
• Structural Grouts &Anchors
• Adhesives and bonding agents
Shelf life
• Concrete repair materials
PolyЯRon BONDIT SBR has a shelf life of 12
months in un-opened pack and if stored in • Joint sealants & Moulding compounds
• XPS Thermal Insulation boards
Built to last
accordance with our instructions.
Storage
PolyЯRon BONDIT SBR should be stored under
enclosed shaded area at temperatures between
5 – 350C.
Precautions/Limitations
• No heavy traffic until the repair has
cured.
• PolyЯRon BONDIT SBR should not be
used at temperatures below 50 C
HPI/TDS/1912-6.6A
HP INDUSTRIES W.L.L
Street no.1,New Industrial Zone,Doha-Qatar, IAS0310Q1101
211
212