Professional Documents
Culture Documents
Features:
- foil capsule vs. glass
- flexibly to fit in irregular holes HVU-TZ capsule
Anchor size M10 M12 M16 M16L M20 M10 M12 M16 M16L M20
Tensile NRec 15.6 19.1 25.8 33.6 53.2 9.5 15.9 18.4 23.9 38.0
Shear VRec 10.3 15.4 29.1 29.1 50.3 10.3 15.4 29.1 29.1 50.3
Anchor size M10 M12 M16 M16L M20 M10 M12 M16 M16L M20
Tensile NRd 21.8 26.7 36.2 47.0 74.5 13.3 22.2 25..8 33.5 53.2
Shear VRd 16.0 24.0 44.8 44.8 78.4 16.0 24.0 44.8 44.8 78.4
Setting details
df
d0
HVZ ...
HAS-TZ HAS-E-TZ
hef t fix
h1
hmin
Anchor rod HAS-(E-)TZ M.. 10x75/ tfix 12x95/ tfix 16x105/ tfix 16Lx125/tfix 20x170/ 40
Installation equipment
A rotary hammer (TE5, TE6, TE15, TE-15C, TE-18M, TE35, TE55, TE76); max. setting speed of 850 r.p.m
(rotary hammering action); a drill bit, a blow out pump and a setting tool: TE-C HEX (M10-M16), TE-Y HEX
(M20);
Setting operations
1 2 3 HVU-TZ 4
TE-C HEX
® ® ®
5 6 7 Tinst
trel
tcure
Allow rel time to pass Wait for curing Apply tightening torque.
Sw
dk
dp
Caution: In view of the high loads transferable with HVZ, it must be verified by the user that the load on the
concrete structure including the loads introduced by the anchorage do not cause failure (e.g. cracking) of the
concrete structure.
TENSION
The tensile design resistance of a single anchor Nrec,c/s
is the lower of,
NRd,c : concrete cone/pull-out resistance s
c
NRd,s : steel resistance
h
o
NRd,c NRd,c fB,N f A,N fR,N
3
C25/30 25 30 1.1
C30/37 30 37 1.22 fck,cube
C35/45 35 45 1.34 fB,N
C40/50 40 50 1.41
25
C45/55 45 55 1.48 Limits: 25 N/mm2 d fck,cube d 60 N/mm2
C50/60 50 60 1.55
Concrete cylinder: Concrete cube:
height 30cm, 15cm side length 15cm
diameter
Concrete test specimen geometry
s
f A,N 0 .5 Limits: smin d s d scr,N
6h ef
distance
, M10 M12 M16 M16L M20
c [mm]
50 0.58
60 0.65
65 0.68
70 0.72 0.62
75 0.75 0.64
80 0.78 0.67 0.49
85 0.82 0.70 0.65 0.59 0.50
90 0.85 0.72 0.68 0.61 0.51
95 0.88 0.75 0.70 0.63 0.53
100 0.92 0.78 0.73 0.65 0.54
105 0.95 0.80 0.75 0.67 0.56
110 0.98 0.83 0.77 0.69 0.57
115 1.00 0.86 0.80 0.71 0.59
125 0.91 0.85 0.75 0.62
135 0.96 0.89 0.79 0.65
145 1.00 0.94 0.83 0.68
155 1.00 0.87 0.71
165 0.91 0.74
175 0.95 0.76
185 1.00 0.79
205 0.85
230 0.93
255 1.00
c
fR,N 0.25 0.50 Limits: cmin d c d ccr,N
h ef
Note: If more than 3 edge distances are smaller than ccr,N, please contact your Hilti technical service.
Combined loading: Only if tensile load and shear load applied (See page 31 and section 4 “Examples”).
0
VRd,c VRd,c f B,V f E,V f AR,V
fAR.V c/cmin
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0
Single anchor with
edge influence 1.00 1.31 1.66 2.02 2.41 2.83 3.26 3.72 4.19 4.69 5.20 5.72 6.27 6.83 7.41 8.00
s/cmin 1.0 0.67 0.84 1.03 1.22 1.43 1.65 1.88 2.12 2.36 2.62 2.89 3.16 3.44 3.73 4.03 4.33
1.5 0.75 0.93 1.12 1.33 1.54 1.77 2.00 2.25 2.50 2.76 3.03 3.31 3.60 3.89 4.19 4.50
2.0 0.83 1.02 1.22 1.43 1.65 1.89 2.13 2.38 2.63 2.90 3.18 3.46 3.75 4.05 4.35 4.67
2.5 0.92 1.11 1.32 1.54 1.77 2.00 2.25 2.50 2.77 3.04 3.32 3.61 3.90 4.21 4.52 4.83
3.0 1.00 1.20 1.42 1.64 1.88 2.12 2.37 2.63 2.90 3.18 3.46 3.76 4.06 4.36 4.68 5.00
3.5 1.30 1.52 1.75 1.99 2.24 2.50 2.76 3.04 3.32 3.61 3.91 4.21 4.52 4.84 5.17
4.0 1.62 1.86 2.10 2.36 2.62 2.89 3.17 3.46 3.75 4.05 4.36 4.68 5.00 5.33
4.5 1.96 2.21 2.47 2.74 3.02 3.31 3.60 3.90 4.20 4.52 4.84 5.17 5.50
5.0 2.33 2.59 2.87 3.15 3.44 3.74 4.04 4.35 4.67 5.00 5.33 5.67
5.5 2.71 2.99 3.28 3.57 3.88 4.19 4.50 4.82 5.15 5.49 5.83
6.0 2.83 3.11 3.41 3.71 4.02 4.33 4.65 4.98 5.31 5.65 6.00
6.5 3.24 3.54 3.84 4.16 4.47 4.80 5.13 5.47 5.82 6.17
7.0 3.67 3.98 4.29 4.62 4.95 5.29 5.63 5.98 6.33
7.5 4.11 4.43 4.76 5.10 5.44 5.79 6.14 6.50
8.0 These results are for a two-. 4.57 4.91 5.25 5.59 5.95 6.30 6.67
8.5 Anchor fastening. 5.05 5.40 5.75 6.10 6.47 6.83
9.0 5.20 5.55 5.90 6.26 6.63 7.00
9.5 For fastening made with more 5.69 6.05 6.42 6.79 7.17
10.0 than 2 anchors, use the 6.21 6.58 6.95 7.33
10.5 general formulae for n 6.74 7.12 7.50
11.0 anchors. 7.28 7.67
11.5 7.83
12.0 8.00
3
VRd,s : Steel design shear resistance
Combined loading: Only if tensile load and shear load applied (See page 31 and section 4 “Examples”).