Professional Documents
Culture Documents
I 100 .. 400 A AC/DC Current Transducer DHR-C420: Electrical Data
I 100 .. 400 A AC/DC Current Transducer DHR-C420: Electrical Data
400 A
The transducer for the electronic measurement of DC & distorted AC
waveform currents, with galvanic isolation between the primary circuit
(power) and the secondary circuit (measurement). True RMS 4-20 mA
current output.
Electrical data
Page 1/4
120426/21 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com
Current Transducer DHR-C420
Isolation characteristics
Notes :3) Between primary conductor voltage and ground. The voltage category
could be improved according to the insulation characteristic given by
the cable manufacturer. The UL 508 Standard for Safety for Industrial
Control Equipment requires that only insulated conductors are used as
primary circuit with this transducer.
4)
Between primary (completely filling the aperture) and secondary.
Transfer characteristics
Output in mA
20
4
-Ipn +Ipn
Page 2/4
120426/21 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com
Current Transducer DHR-C420
In order to guarantee safe operation of the transducer and to be able to make proper use of all features and functions,
please read these instructions thoroughly!
Safe operation can only be guaranteed if the transducer is used for the purpose it has been designed for and within the
limits of the technical specifications.
Ensure you get up-to-date technical information that can be found in the latest associated datasheet under www.lem.com.
Ignoring the warnings can lead to serious injury and/or cause damage!
The electric measuring transducer may only be installed and put into operation by qualified personnel
that have received an appropriate training.
The corresponding national regulations shall be observed during installation and operation of the
transducer and any electrical conductor.
The transducer shall be used in electric/electronic equipment with respect to applicable standards and
safety requirements and in accordance with all the related systems and components manufacturers’
operating instructions.
When operating the transducer, certain parts of the module may carry hazardous live voltage (e.g.
primary conductor, power supply).
The user shall ensure to take all measures necessary to protect against electrical shock.
The transducer is a built-in device containing conducting parts that shall not be accessible after
installation.
A protective enclosure or additional insulation barrier may be necessary.
The transducer shall not be put into operation if the jaw opening is open (split core version) or the
installation is not completed.
Installation and maintenance shall be done with the main power supply disconnected except if there
are no hazardous live parts in or in close proximity to the system and if the applicable national
regulations are fully observed.
Safe and trouble-free operation of this transducer can only be guaranteed if transport, storage and installation are carried
out correctly and operation and maintenance are carried out with care.
Page 3/4
120426/21 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com
Dimensions DHR-C420 (in mm. 1 mm = 0.0394 inch)
25
70
Dimensions DHR-C420 (in mm.
60 1 mm = 0.0394 inch)
25
60
70
4.
60
32
70
6.80
60
40
4.
6.80
32
15
25
70
10
6.80
40
8.30
22.28
8.30
4
6.80
90
15
25
20.34
10
22.28 2.50
15
90
4
2.50
33.80
25.60
15
4.60
8.30
33.80
25.60
4.60
7
6 78
8.30
6 78 Plug
Plugin in
connector:
connector:
FKC2.5/4-ST-5.08
FKC 2.5/4-ST-5.08-RF
(Phoenix
(Phoenix Contact)
Contact)
DHR-C420 Connections
Connections
●● Wires up to Ø 2 mm
DHR • Wires
●● up to ∅ 2connector
Female mm provided (spring terminal blocks)
• Female connector provided
●● User-friendly (springconnection
spring-cage terminal blocks)
for no-tool direct
• User-friendly spring-cage
conductor connection for no-tool
connection
Output Connector direct conductor connection
1(Vcc) 2(Iout) 3(NC) 4(GND)
Mechanical characteristics
24 VDC Power
●● General
Mechanical tolerance
characteristics ±1 mm
(+) ●● Primary aperture Ø 32.0 mm
• General tolerance
●● Panel mounting ±1 mm 4 holes Ø 4.6 mm
(-) • Primary aperturebetween holes
●● Distance ∅ 32.0 mm 70.0 mm & 78 mm
• Panel mounting
(see above dimensions)4 holes ∅ 4.6 mm
• Distance
Forbetween holes
panel mounting, 70 M4
use mm screws
& 78 mm (not supplied) with
(see above drawings)
appropriate length to panel´s thickness, and tighten to
(-) (+)
For panel0.75Nm
mounting, replace
+/-20% M4 screws by new one (not supplied)
torque.
Load
with appropriate length to panel´s thickness.
(Controller, meter etc)
Remarks
●● The temperature of the primary busbar can not exceed
Remarks
90 °C.
+24VDC • The ●temperature of the primary conductor
● Dynamic performances are the bestcanwith
not a
exceed 90 °C.
primary
OUT Is
• Dynamic performances
busbar arefilling
completely the bestthe with a primary
primary conductor
aperture.
Ip
completely
●● Thisfilling the primary
is a standard aperture.
model. For different versions
• This is (supply
a standard model. For different
voltages, different versions
outputs, (supply voltages,
bidirectional
GND differentmeasurements...),
outputs, bidirectional
please contact us. please
measurement,...),
contact us. Page 4/4
120426/21 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com
Page 4/4
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.
080725/16 www.lem.com