Professional Documents
Culture Documents
DSC1106032CE
B26
Colour
[DMC-G3K] [DMC-G3W]
(K)...........Black Type (K)...........Black Type
(R)...........Red Type (except GD/GT) (R)...........Red Type (except PP/EE/GD/GT)
(W)..........White Type (except PC/EG) (W)..........White Type (except PP/EB/EE/EG)
(T)...........Brown Type (only PP/EG/GC) (T)...........Brown Type (only EG/GC)
(KA).........Black Type (only EB)
[DMC-G3]
(K)...........Black Type
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3 7 Troubleshooting Guide --------------------------------------- 24
1.1. General Guidelines ----------------------------------------3 7.1. Checking Method of Body and
1.2. Leakage Current Cold Check ---------------------------3 Interchangeable Lens ---------------------------------- 24
1.3. Leakage Current Hot Check (See Figure 1.)--------3 8 Service Fixture & Tools--------------------------------------- 29
1.4. How to Discharge the E. Capacitor on Flash 8.1. Service Fixture and Tools------------------------------ 29
P.C.B.----------------------------------------------------------4 8.2. Clean Box-------------------------------------------------- 30
2 Warning --------------------------------------------------------------5 8.3. Service Position ------------------------------------------ 31
2.1. Prevention of Electrostatic Discharge (ESD) 9 Disassembly and Assembly Instructions -------------- 32
to Electrostatically Sensitive (ES) Devices ----------5 9.1. Camera Body Part--------------------------------------- 32
2.2. How to Recycle the Lithium Ion Battery (U.S. 9.2. Disassembly and Assemble Procedure for the
Only)-----------------------------------------------------------5 Lens (H-FS014042) ------------------------------------- 43
2.3. Caution for AC Cord (For EB/GC/GH) ----------------6 9.3. Disassembly and Assemble Procedure for the
2.4. How to Replace the Lithium Battery -------------------7 Lens (H-FS045200) ------------------------------------- 44
3 Service Navigation------------------------------------------------8 10 Measurements and Adjustments -------------------------- 45
3.1. Introduction --------------------------------------------------8 10.1. Matrix Chart for Replaced Part and Necessary
3.2. Important Notice --------------------------------------------8 Adjustment ------------------------------------------------ 45
3.3. General Description About Lead Free Solder 11 Maintenance------------------------------------------------------ 47
(PbF) -------------------------------------------------------- 12 11.1. Notice in external cleaning ---------------------------- 47
3.4. How to Define the Model Suffix (NTSC or PAL 11.2. General description (Lens cleaning:
model)------------------------------------------------------- 13 Interchangeable Lens/H-FS014042)---------------- 48
4 Specifications ---------------------------------------------------- 17 11.3. General description (Lens cleaning:
5 Location of Controls and Components------------------ 18 Interchangeable Lens/H-FS045200)---------------- 51
6 Service Mode ----------------------------------------------------- 22
6.1. Error Code Memory Function ------------------------- 22
2
1 Safety Precautions
1.1. General Guidelines 1.3. Leakage Current Hot Check
1. IMPORTANT SAFETY NOTICE (See Figure 1.)
There are special components used in this equipment
1. Plug the AC cord directly into the AC outlet. Do not use
which are important for safety. These parts are marked by
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
in the Schematic Diagrams, Circuit Board Layout,
capacitor, between each exposed metallic part on the set
Exploded Views and Replacement Parts List. It is essen-
and a good earth ground, as shown in Figure 1.
tial that these critical parts should be replaced with manu-
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
facturer’s specified parts to prevent X-RADIATION,
measure the potential across the resistor.
shock, fire, or other hazards. Do not modify the original
4. Check each exposed metallic part, and measure the volt-
design without permission of manufacturer.
age at each point.
2. An Isolation Transformer should always be used during
5. Reverse the AC plug in the AC outlet and repeat each of
the servicing of AC Adaptor whose chassis is not isolated
the above measurements.
from the AC power line. Use a transformer of adequate
6. The potential at any point should not exceed 0.75 V RMS.
power rating as this protects the technician from acci-
A leakage current tester (Simpson Model 229 or equiva-
dents resulting in personal injury from electrical shocks. It
lent) may be used to make the hot checks, leakage cur-
will also protect AC Adaptor from being damaged by acci-
rent must not exceed 1/2 mA. In case a measurement is
dental shorting that may occur during servicing.
outside of the limits specified, there is a possibility of a
3. When servicing, observe the original lead dress. If a short
shock hazard, and the equipment should be repaired and
circuit is found, replace all parts which have been over-
rechecked before it is returned to the customer.
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
3
1.4. How to Discharge the E. Capacitor on Flash P.C.B.
CAUTION:
1. Be sure to discharge the E. Capacitor on FLASH P.C.B..
2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1kΩ /5W).
(An equivalent type of resistor may be used.)
3. Put the resistor between both terminals of E. Capacitor on FLASH P.C.B. for approx. 5 seconds.
4. After discharging, confirm that the E. Capacitor voltage is lower than 10V by using a voltmeter.
Fig. F1
4
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
5
2.3. Caution for AC Cord 2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
(For EB/GC/GH) the following code:
2.3.1. Information for Your Safety
IMPORTANT Blue Neutral
Your attention is drawn to the fact that recording of pre- Brown Live
recorded tapes or discs or other published or broadcast
As the colours of the wires in the mains lead of this appliance
material may infringe copyright laws.
may not correspond with the coloured markings identifying the
WARNING
To reduce the risk of fire or shock hazard, do not expose terminals in your plug, proceed as follows:
this equipment to rain or moisture.
CAUTION The wire which is coloured BLUE must be connected to the ter-
To reduce the risk of fire or shock hazard and annoying minal in the plug which is marked with the letter N or coloured
interference, use the recommended accessories only. BLACK.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER The wire which is coloured BROWN must be connected to the
To prevent electric shock, do not remove the cover. No user terminal in the plug which is marked with the letter L or coloured
serviceable parts inside. Refer servicing to qualified service RED.
personnel.
Under no circumstances should either of these wires be con-
2.3.2. Caution for AC Mains Lead nected to the earth terminal of the three pin plug, marked with
For your safety, please read the following text carefully. the letter E or the Earth Symbol.
6
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the MAIN P.C.B.. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B9110” at foil side of MAIN P.C.B.) and
remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Type No. ML421 includes electric lead terminals.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML421 Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-G3K/G3W/G3 series, as well.
7
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
Fig. S1
8
3.2.1.2. About Mount Box Unit (Ref. 16)
1. This Service Manual does not contain the following repair service information for "MOUNT BOX UNIT"(Ref.16), because it
requires special facilities and equipment.
a. Schematic diagram, Block diagram and P.C.B. layout.
b. Parts list for individual parts.
2. If the "MOUNT BOX UNIT" is confirmed as defective, exchange the "MOUNT BOX UNIT" as a unit (supplied as service parts
size).
3. Before exchanging the "MOUNT BOX UNIT", the performances must be carefully checked, by following the "7.Troubleshoot-
ing Guide" section of this service manual.
Important:
1. After replacing the MOUNT BOX UNIT, the mount box data has to be stored to the unit.
The mount box unit supplied as service parts has affix the label of own configure data.
By inputting these data into the adjustment software and writting these data to VENUS FHD (IC6001), the shutter adjustment
becomes needless.
In addition, the adjustment software can read data encoded to QR code by using WEB camera with a close-up function.
Refer to the adjustment instruction in the adjustment software for details.
Fig. S2
2. The full adjustment must be performed after replacing the "MOUNT BOX UNIT", otherwise picture quality can not be meet
with specification.
9
3.2.2. Lens Unit (Interchangeable Lens: H-FS014042)
3.2.2.1. About Lens Main Block Unit (Ref. 208)
1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.208), because it
requires special facilities and equipment.
2. The "LENS MAIN BLOCK UNIT"(Ref.208) performance must be confirmed.
3. In case of the "LENS MAIN BLOCK UNIT"(Ref.208) defect, contact to the service department of sales company.
Fig. S3
10
3.2.3. Lens Unit (Interchangeable Lens: H-FS045200)
3.2.3.1. About Lens Main Block Unit (Ref. 308)
1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.308), because it
requires special facilities and equipment.
2. The "LENS MAIN BLOCK UNIT"(Ref.308) performance must be confirmed.
3. In case of the "LENS MAIN BLOCK UNIT"(Ref.308) defect, contact to the service department of sales company.
Fig. S4
11
3.3. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
12
3.4. How to Define the Model Suffix (NTSC or PAL model)
There are eight kinds of DMC-G3 (Camera body unit), regardless of the colours.
• a) DMC-G3 (Japan domestic model)
• b) DMC-G3PP/PC
• c) DMC-G3EB/EC/EG/GH/GN
• d) DMC-G3EE
• e) DMC-G3GK
• f) DMC-G3GT
• g) DMC-G3GD
• h) DMC-G3GC
What is the difference is that the “INITIAL SETTINGS” data which is stored in VENUS FHD mounted on MAIN P.C.B..
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
Refer to the adjustment instruction in the adjustment software for details.
13
3.4.2. INITIAL SETTINGS:
After replacing the MAIN P.C.B., make sure to perform the initial settings after achieving the adjustment by ordering the following
procedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, make sure to read the following CAUTION.
2. PROCEDURES:
• Precautions: Read the above “CAUTION” carefully.
• Preparation:
Attach the fully charged Battery, and insert the SD memory card.
Confirm that it is not intelligent auto mode [iA] or intelligent auto plus mode [iA+].
NOTE:
If the unit is intelligent auto mode [iA] or intelligent auto plus mode [iA+], it does not display the initial settings menu.
• Step 1. The temporary cancellation of “INITIAL SETTINGS”:
While pressing [ Q.MENU/Fn2 ], [ DISP/Fn1 ] and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power on.
• Step 2. The cancellation of “INITIAL SETTINGS”:
Press the [ PLAYBACK ] button, then playback the picture.
Press [ Q.MENU/Fn2 ] and “[ UP ] of Cursor buttons” simultaneously, then turn the Power off.
• Step 3. Turn the Power on:
SEt the mode dial to [ P ] (Program AE Mode), then turn the Power on.
• Step 4. Display the INITIAL SETTING:
While pressing “[ RIGHT ] of Cursor buttons” and [ MENU/SET ] simultaneously, turn the Power off.
The “INTIAL SETTINGS” menu is displayed.
There are two kinds of “INITIAL SETTINGS” menu form as follows:
[CASE 1. After replacing MAIN P.C.B.]
[Except "EG, EB, EC and OLY" models : (VEP56135A is used as a Main P.C.B.)]
When MAIN P.C.B. has just been replaced, all of the model suffix are displayed as follows. (two pages in total)
14
[Only for "EG, EB EC and OLY" models : (VEP56135B is used as a Main P.C.B.)]
When MAIN P.C.B. has just been replaced, only 4 model suffix are displayed as follows.
15
• Step 7. CONFIRMATION:
Confirm the display of “PLEASE SET THE CLOCK” in concerned language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
1) As for your reference, major default setting condition is as shown in the following table.
• Default setting (After “INITIAL SETTINGS”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-G3 (Japan domestic model) NTSC Japanese Year/Month/Date
b) DMC-G3PP NTSC English Month/Date/Year
c) DMC-G3PC NTSC English Month/Date/Year
d) DMC-G3EB PAL English Date/Month/Year
e) DMC-G3EC PAL English Date/Month/Year
f) DMC-G3EE PAL Russian Date/Month/Year
g) DMC-G3EG PAL English Date/Month/Year
h) DMC-G3GC PAL English Date/Month/Year
i) DMC-G3GD NTSC Korean Year/Month/Date
j) DMC-G3GH PAL English Date/Month/Year
k) DMC-G3GK PAL Chinese (simplified) Year/Month/Date
l) DMC-G3GN PAL English Date/Month/Year
m) DMC-G3GT NTSC Chinese (Traditional) Year/Month/Date
16
4 Specifications
17
5 Location of Controls and Components
Camera body
1 Sensor 1 2 3
2 Flash
3 Self-timer indicator /
AF Assist Lamp
4 Lens fitting mark
5 Mount
6 Lens lock pin
7 Lens release button
4 5 6 7
8 [LVF/LCD] button
9 Diopter adjustment dial 8 9 10 11 12 13 14 15
10 Viewfinder
11 Playback button
12 Motion picture button
13 Camera ON/OFF switch
14 Rear dial
15 [DISP./Fn1] button
16 Eye Cup
17 Touch panel/LCD monitor
18 [Q.MENU/Fn2] button /
Delete/Return button
16 17 18 19 20
19 [MENU/SET] button
20 Cursor buttons
/ISO
/WB (White Balance)
/AF Mode button
/[DRIVE MODE] button
This button in picture record mode will allow the user to select between the following
options.
Single /Burst /Auto bracket /Self-timer
18
21 Shoulder strap eyelet
Be sure to attach the shoulder strap when
using the camera to ensure that you will not
drop it.
21
22 [REMOTE] socket 22
23 [HDMI] socket
24 [AV OUT/DIGITAL] socket 23
24
34 35 36 37
Lens
H-FS014042 H-FS045200
(LUMIX G VARIO 14– 42 mm/F3.5 – 5.6 (LUMIX G VARIO 45– 200 mm/F4.0 – 5.6/
ASPH./MEGA O.I.S.) MEGA O.I.S.)
42
41
38 39 40 41 42 43 44 38 39 40 45 43 44
38 Tele
39 Lens surface
40 Focus ring
41 Wide
42 Zoom ring
43 Contact point
44 Lens fitting mark
45 [O.I.S.] switch
19
Selecting the Recording Mode
To select a Recording Mode with the mode dial
Press [}].
[}] button will light up when it is switched to Intelligent Auto Mode.
The Recording Mode selected by the mode dial is disabled while the [}]
button is lit.
Basic
Program AE Mode
The subjects are recorded using your own settings.
Advanced
Aperture-Priority AE Mode
The shutter speed is automatically determined by the aperture value you set.
Shutter-Priority AE Mode
The aperture value is automatically determined by the shutter speed you set.
Custom Mode
Use this mode to take pictures with previously registered settings.
Scene Mode
This allows you to take pictures that match the scene being recorded.
20
Touch Panel
This touch panel is a type that detects pressure.
Drag
Touch the screen
A movement without releasing the touch
To touch and release the touch panel.
panel.
Use this to perform tasks such as selecting This is used to move the AF area, operate
icons or images displayed on the touch the slide bar, etc.
panel. This can also be used to move to the next
When selecting features using the touch image during playback, etc.
panel, be sure to touch the center of the
desired icon.
Note
If you use a commercially available liquid crystal protection
sheet, please follow the instructions that accompany the sheet.
(Some liquid crystal protection sheets may impair visibility or
operability.)
If a commercially available protection sheet is used, a little extra
pressure may be required if you notice that the touch panel is
not responsive.
Avoid having the hand holding the camera accidently apply
pressure to the touch panel. Doing so may affect the touch panel
operation.
Do not press on the LCD monitor with hard pointed tips, such as
ball point pens.
Do not operate with your fingernails.
Wipe the LCD monitor with dry soft cloth when it gets dirty with finger prints and others.
Do not scratch or press the LCD monitor too hard.
For information about the icons displayed on the touch panel.
21
6 Service Mode
6.1. Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly.
(i.e., when the unit is powered on by the battery, the battery is pulled out)
The error code is memorized to FLASH-ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
• Preparation
Attach the fully charged Battery, and insert the SD memory card.
Confirm that it is not intelligent auto mode [iA] or intelligent auto plus mode [iA+].
NOTE:
If the unit is intelligent auto mode [iA] or intelligent auto plus mode [iA+], it does not display the initial settings menu.
• Step 1. The temporary cancellation of “INITIAL SETTINGS”:
While pressing [ Q.MENU/Fn2 ], [ DISP/Fn1 ] and "[ RIGHT ] of Cursor buttons" simultaneously, turn the Power on.
• Step 2. Execute the error code display mode:
Press [ Q.MENU/Fn2 ], [ MENU/SET ] and "[ LEFT ] of Cursor buttons" simultaneously with the step 1 condition.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display → Error code display → Camera information display → Normal display → .....
22
• Error Code List:
The error code consists of 8 bit data and it shows the following information.
23
7 Troubleshooting Guide
7.1. Checking Method of Body and Interchangeable Lens
24
25
26
27
28
8 Service Fixture & Tools
8.1. Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.
29
8.2. Clean Box
• The repair quality is considered, and it is recommended working in the environment of satisfied clean level less than class 10,000
(Federal Standard 209D).
(When remove the 1st lens frame, it is indispensable.)
[NOTE]
• Work in the environment of satisfied clean level less than class 10,000 (Federal Standard 209D) when remove the 1st lens frame
for cleaning.
*Refer to "11.2. General description (Lens cleaning: Interchangeable Lens/H-FS014042)", "11.3. General description (Lens
cleaning: Interchangeable Lens/H-FS045200)" section of this service manual for details.
30
8.3. Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection Form
1 RFKZ0583 FP9007(MAIN) - HOT SHOE FPC 19PIN 0.3 FFC
2 RFKZ0477 FP9003(MAIN) - LVF UNIT 45PIN 0.3 FFC
3 VFK1976 FP9005(MAIN) - FPC←→FP8001(TOP) 19PIN 0.5 FFC
4 RFKZ0393 FP9010(MAIN) - FPC←→FP4202(MIC) 15PIN 0.3 FFC
5 RFKZ0583 FP9006(MAIN) - MOUNT BOX UNIT(SHUTTER) 19PIN 0.3 FFC
6 RFKZ0477 FP9004(MAIN) - LCD UNIT 45PIN 0.3 FFC
7 RFKZ0477 FP3912(MAIN) - MOUNT BOX UNIT 45PIN 0.3 FFC
8 RFKZ0477 FP3913(MAIN) - MOUNT BOX UNIT 45PIN 0.3 FFC
9 RFKZ0583 FP9009(MAIN) - FPC←→FP8501(FLASH) 19PIN 0.3 FFC
10 RFKZ0564 FP9001(MAIN) - MOUNT BOX UNIT(LENS I/F) 23PIN 0.3 FFC
11 VFK1480 FP9008(MAIN) - REAR OPERATION UNIT 6PIN 0.5 FFC
31
9 Disassembly and Assembly Instructions
9.1. Camera Body Part
9.1.1. Disassembly Flow Chart
This is a disassembling chart.
When assembling, perform this chart conversely.
32
9.1.3. Disassembly Procedure No. Item Fig Removal
12 Rear Earth Plate (Fig. D17) 4 Screws (P)
1 Screw (Q)
No. Item Fig Removal 2 Screws (R)
1 Rear Case Unit (Fig. D1) 4 Screws (A) (Fig. D18) Grip Piece Rear
8 Screws (B) 2 Locking tabs
(Fig. D2) Side Ornament R Arm Cover Top
Side Ornament L Arm Cover Bottom
Jack Door Rear Earth Plate
Eye Rubber 13 Rear Operation P.C.B. (Fig. D19) 1 Screw (S)
2 Screws (C) LCD Lock Holder
(Fig. D3) FP9004(Flex) Rear Operation P.C.B.
FP9008(Flex) 14 Hinge SW FPC Unit (Fig. D20) 2 Screws (T)
Rear Case Unit LCD Unit 1 Screw (U)
2 Main P.C.B. (Fig. D4) 1 Screw (D) Flex
3 Screws (E) Hinge Plate
FP9003(Flex) 2 Screws (V)
2 Tapes (A) (Fig. D21) 6 Ribs
1 Tape (B) Hinge SW FPC Unit
FP3911(Flex) LCD Unit
FP3912(Flex) 15 LCD IF P.C.B. (Fig. D22) 2 Screws (W)
FP3913(Flex) 2 Screws (X)
FP9001(Flex) 6 Locking tabs
FP9002(Flex) LCD Case Bottom
FP9005(Flex) LCD Hinge Unit
FP9006(Flex) FP7202(Flex)
FP9007(Flex) FP7203(Flex)
FP9009(Flex) FP7204(Flex)
FP9010(Flex) FP7205(Flex)
(Fig. D5) Main P.C.B. LCD PCB Sheet
3 Front Case Unit (Fig. D6) 2 Screws (F) LCD IF P.C.B.
(Fig. D7) 2 Screws (G) 16 LCD Unit (Fig. D23) LCD BL Bezel Sheet
Front Case Unit LCD Case Top
4 Mount Box Unit (Fig. D8) 4 Screws (H) 4 Locking tabs
Mount Box Unit Backlight Unit
5 Top Case Unit (Fig. D9) 2 Screws (I) LCD Unit
5 Locking tabs
Capacitor PCB Cover
P8502(Connector)
P8503(Connector)
Top Case Unit
6 Flash P.C.B. (Fig. D10) 1 Screw (J)
1 Screw (K)
Tape
Flash P.C.B.
(Fig. D11) Caution for Discharging
7 Battery Door Unit (Fig. D12) Battery Door Shaft
Battery Door Spring
Battery Door Unit
8 Battery Case (Fig. D13) 2 Locking tabs
Heat Radiation Plate
3 Locking tabs
Battery Out Spring
Battery Lock Knob
Battery Lock Spring
Battery Case
9 LVF Unit (Fig. D14) 2 Screws (L)
LVF Unit
10 Top P.C.B. (Fig. D15) 2 Screws (M)
FP8002(Flex)
Multi-Button Switch
1 Screw (N)
Top P.C.B.
11 Mic P.C.B. (Fig. D16) FP4201(Flex)
FP4202(Flex)
1 Screw (O)
Mic P.C.B.
33
9.1.3.1. Removal of the Rear Case Unit
(Fig. D1)
(Fig. D2)
34
9.1.3.2. Removal of the Main P.C.B.
(Fig. D3)
(Fig. D4)
35
(Fig. D5)
(Fig. D7)
(Fig. D6)
36
9.1.3.4. Removal of the Mount Box Unit 9.1.3.5. Removal of the Top Case Unit
(Fig. D9)
(Fig. D8)
(Fig. D10)
37
9.1.3.8. Removal of the Battery Case
(Fig. D11)
(Fig. D12)
(Fig. D13)
38
9.1.3.9. Removal of the LVF Unit 9.1.3.11. Removal of the Mic P.C.B.
(Fig. D16)
(Fig. D14)
9.1.3.12. Removal of the Rear Earth Plate
9.1.3.10. Removal of the Top P.C.B.
(Fig. D17)
(Fig. D15)
39
9.1.3.14. Removal of the Hinge SW FPC
Unit and LCD Unit
(Fig. D18)
(Fig. D19)
(Fig. D20)
40
9.1.3.15. Removal of the LCD IF P.C.B.
(Fig. D21)
(Fig. D22)
41
9.1.3.16. Removal of the LCD Unit
(Fig. D23)
NOTE: (When Installing)
Make sure to confirm the following points when installing:
• The Screw is tightened enough.
• Installing conditions are fine. (No distortion, no abnormal-
space.)
• No dust and/or dirt on Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
42
9.2. Disassembly and Assemble Procedure for the Lens (H-FS014042)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. K1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the “11 Maintenance” for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
(Fig. K1)
43
9.3. Disassembly and Assemble Procedure for the Lens (H-FS045200)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to “8.2. Clean Box” section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. W1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the “11 Maintenance” for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
(Fig. W1)
44
10 Measurements and Adjustments
10.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
After updates it to the latest firmware, the adjustment is executed.
*1
• Inspect it, not only corresponding part is replaced, but also camera body is shocked and/or dropped.
• The Panasonic camera body in accordance with the Micro Four Thirds system (DMC-G1 unit, etc. marketed commodity: oper-
ates normal) and a standard zoom lens H-FS014045 (marketed commodity: operates normal) is required as a reference
machine.
• Refer to the adjustment instruction in the adjustment software for details.
45
*3 NOTE: (After exchange the mount box unit)
• Execute the resolution inspection by the comparison with the standard model (DMC-G1K etc.: operates normal).
• Refer to the adjustment instruction in the adjustment software for details.
*4
• Confirm self recording/playback motion picture of AVCHD mode by the LCD.
• Confirm it on the TV with HDMI socket when repair HDMI relation.
46
11 Maintenance
11.1. Notice in external cleaning
11.1.1. ABOUT THE BODY
NOTE:
Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the SD Memory card and lens unit.
47
11.1.2. ABOUT THE LENS
11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
48
11.2.1. Disassembly procedure 11.2.1.3. Removal of a dust /dirt
Important: 1. Blow off the dust on the surface of the lens with a blower
It must be performed inside of satisfied clean level. brush.
(Satisfied clean level: Less than class 10,000 (Federal 2. Use lens cleaning KIT(BK) (VFK1900BK), if necessary.
Standard 209D))
49
11.2.2. Assembly procedure 11.2.2.2. Installation of the Decoration Ring
Important: 1. Use the Name Ring fixture (RFKZ0507)
When tightening the screw, use a torque driver (RFKZ0456) 2. Use new Decoration ring. (Do not use the one which is
by ordering the screwing order with specified torque removed.)
described in each step.
50
11.3. General description (Lens cleaning: Interchangeable Lens/H-FS045200)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
51
11.3.1. Disassembly procedure 11.3.1.2. Removal of the 1st Lens Frame
Important: Unit
It must be performed inside of satisfied clean level.
1. Remove the 3 screws (A).
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
52
11.3.2. Assembly procedure 2. Tighten the 3 screws (A) with specified torque in numeri-
Important: cal order.
When tightening the screw, use a torque driver (RFKZ0456) (Torque Driver: RFKZ0456)
by ordering the screwing order with specified torque (Torque: 14.7 ± 1.0 N-cm)
described in each step.
53
11.3.2.2. Installation of the Decoration Ring
1. Use the Name Ring fixture (RFKZ0507)
2. Use new Decoration ring. (Do not use the one which is
removed.)
54
DSC1106032CE
S1. About Indication of The Schematic Diagram
Service Manual S1.1. Important Safety Notice
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
Parts List schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
Digital Camera/Lens Kit/ 3.The voltage being indicated on the schematic diagram is measured in
Double Zoom Lens Kit/Body "Standard-Playback" mode when there is no specify mode is mentioned.
Model No. 4.Although the voltage and waveform available on here is measured with standard frame,
DMC-G3KPP DMC-G3KGH DMC-G3EE DMC-G3WEC it may be differ from actual measurement due to modification of circuit and so on.
DMC-G3KPC DMC-G3KGK DMC-G3EG DMC-G3WEE
DMC-G3KEB DMC-G3KGN DMC-G3GC DMC-G3WEG 5.The voltage being indicated here may be include observational-error (deviation) due to
DMC-G3KEC DMC-G3KGT DMC-G3GD DMC-G3WGC internal-resistance and/or reactance of equipment. Therefore, handle the value
DMC-G3KEE DMC-G3PP DMC-G3GH DMC-G3WGD indicated on here as reference.
DMC-G3KEG DMC-G3PC DMC-G3GN DMC-G3WGH
DMC-G3KGC DMC-G3EB DMC-G3GT DMC-G3WGK 6.Use the parts number indicated on the Replacement Parts List .
DMC-G3KGD DMC-G3EC DMC-G3WPP DMC-G3WGN 7.Indication on Schematic diagrams:
Vol. 1 DMC-G3WEB DMC-G3WGT
Colour Circuit name being connected.
[DMC-G3K] [DMC-G3] [DMC-G3W]
(K)........Black Type (K)........Black Type (K)........Black Type
(R)...........Red Type (except GD/GT) (R)...........Red Type (except PP/EE/GD/GT)
FEP This signal is connected
(W)..........White Type (except PC/EG) (W)..........White Type (except PP/EB/EE/EG) OFTR
to the FEP schematic diagram.
(T)...........Brown Type (only PP/EG/GC) (T)...........Brown Type (only EG/GC)
(KA).........Black Type (only EB)
DMC-G3K series: Interchangeable Lens (H-FS014042) is bundled.
DMC-G3W series: Interchangeable Lens (H-FS014042/H-FS045200) are bundled. Name of Signal
DMC-G3 series: Camera Body Only.
Table of contents
S1. About Indication of The Schematic Diagram............................. S-1 S5.4. MIC P.C.B............................................................................. S-12
S1.1. Important Safety Notice......................................................... S-1
S6. Replacement Parts List........................................................... S-13
S2. Voltage Chart............................................................................ S-2
S2.1. Flash P.C.B............................................................................ S-2 S7. Exploded View........................................................................ S-22
S7.1. Frame and Casing Section.................................................. S-22
S3. Block Diagram........................................................................... S-3 S7.2. Camera Lens Section (1)..................................................... S-23
S3.1. Overall Block Diagram........................................................... S-3 S7.3. Camera Lens Section (2)..................................................... S-24
S7.4. Packing Parts and Accessories Section (1)......................... S-25
S4. Schematic Diagram................................................................... S-4 S7.5. Packing Parts and Accessories Section (2)......................... S-26
S4.1. Interconnection Diagram........................................................ S-4 S7.6. Packing Parts and Accessories Section (3)......................... S-27
S4.2. Top Operation Schematic Diagram........................................ S-5
S4.3. Flash Schematic Diagram...................................................... S-6
S4.4. Rear Operation Schematic Diagram...................................... S-7
S4.5. MIC Schematic Diagram........................................................ S-8
S-1
S2. Voltage Chart
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
S-2
S3. Block Diagram
S3.1. Overall Block Diagram
SD
IC3101 CARD
LENS UNIT MOS SENSOR ANALOG
16M FRONTEND
REMOTE
TERMINAL
IC9901
MOTOR DRIVE
AV OUT / DIGITAL
TERMINAL
IC9001
IC9003
IC9801 IC6101
Q9801, T9801 BUS SWITCH
HDMI
TERMINAL
IC6001
VENUS FHD
EXT. FLASH Q8001,8002
HOT SHOE QR6001-6003
CAMERA PROCESS
(OPTION) UNIT QR8001-8002
J-PEG COMP/EX PANDS
MEDIA I/F
USB I/F IC7201
MAIN MICROPROCESSOR TOUCH PANEL TOUCH PANEL
OIS CONTROL DRIVER
LENS DRIVE
LCD DRIVE COLOR LCD
DDR MOBILE RAM1 /1G-bit PANEL
FLASH Q8501,8502 DDR MOBILE RAM1 /1G-bit
NOR FLASH MEMORY/128M-bit 3.0" PANEL
QR6003,8501
HDMI DRIVER 460k dots
QR8502
X9101 IC9101
(32.768kHz) SYSTEM IC
IC1001
POWER BATTERY
(POWER SUPPLY)
HOT SHOE
S-3
HINGE FPC
38 GND 39 GND
36 BL- 37 BL+
1 XP
34 S TPANEL SCK 35 GND
2 YN
32 S TPANEL SO 33 S TPANEL CS
3 XN
31 S TPANEL SI
FP7205
30 TPANEL REQ 4 YP
28 LCD CS 29 GND
26 LCD SDOUT 27 LCD SCK
24 LCDOUT1 25 LCDOUT0
22 LCDOUT3 23 LCDOUT2
21 LCDOUT4
HINGE SW FPC
20 LCDOUT5
18 LCDOUT7 19 LCDOUT6
FP7202
16 LCDOUT9 17 LCDOUT8
14 LCDOUT11 15 LCDOUT10
12 LCDOUT13 13 LCDOUT12
1 FP
10 LCDOUT15 11 LCDOUT14 2 7
9 LCD CLK BL 204
8 LCDHD 3 BL PLU
6 D3V 7 LCDVD 4 MI
NU S
4 D3V 5 D3V NC S
2 GND 3 D1R8V NC
1 GND
9
7
5
3
1
11
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
S4. Schematic Diagram
S4.1. Interconnection Diagram
VS
C3P
C4P
C1N
C2N
DR0
DR2
DR4
DR6
VGL
DG0
DG2
DG4
DG6
CXP
SDA
VCIM
VSS1
VDDL
SCEN
VCIX2
HSYNC
VCOML
FP9006
8
6
4
2
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
1
FP7203
MOT(1) 2 MOT(1) 1 LCD ROTATE2
3 MOT(1) 2 GND
4 MOT(1) 3 LCD OPEN H
5 MOT(2) 4 GND
6 MOT(2) 5 GND
(FOIL SIDE)
7 MOT(2) 6 D1R8V
7 D3V
HOT SHOE
8 MOT(2) 8 D3V
9 2CMG
VCI
9 D3V
LCD IF P.C.B.
C1P
C2P
SCL
DR1
DR3
DR5
DR7
C3N
C4N
DG1
DG3
DG5
DG7
CXN
VGH
VGM
10 COM(MOT4R8V)
VSS2
DCLK
10 LCD VD
VSYNC
VCOMH
VDDIO1
11 COM(MOT4R8V) 12 1CMG 11 LCD HD
13 LPSW 12 LCD CLK
14 GND(LPSW) 13 LCDOUT15
15 BRUSH(1) 14 LCDOUT14
16 BRUSH(2) 15 LCDOUT13
16 LCDOUT12
17 BRUSH GND 18 BRUSH GND 17 LCDOUT11
19 BRUSH(3) 18 LCDOUT10
19 LCDOUT9
20 LCDOUT8
21 LCDOUT7
22 LCDOUT6
23 LCDOUT5
FP9004
24 LCDOUT4
25 LCDOUT3
26 LCDOUT2
27 LCDOUT1
28 LCDOUT0
29 LCD SDOUT
30 LCD SCK
31 LCD CS
SPEAKER
32 GND
33 TPANEL REQ
SHUTTER FPC
FP3912 34 S TPANEL SI
35 S TPANEL SO
1 GND 36 S TPANEL CS
HOT SHOE FPC
(SHUTTER)
16 DP D R 18 GND
17 CCL D R 17 GND
LCD UNIT
18 LGCEL D R 16 GND
19 MPXLOW D R 15 LED AF VCC
20 SLIMIT2 D R 14 LED AF OUT
21 SLIMIT1 D R
TOUCH PANEL
22 VDDCEL D R 12 G SP POS 13 NC
23 PWB D R 11 G SP NEG FP8001
24 PWB D R 10 NC
25 GND 9 STRTTL
26 CLDCNC D R 8 STRXD 23 TOP KEY IN
27 AVDD D 7 STTXD 22 CMD DIAL1
28 AVDD D 6 NC 21 CMD DIAL0
29 GND 5 NC 20 SHUTTER HALF
30 AOUTB D(R) 4 NC 19 SHUTTER FULL
31 GND 3 STX 18 LED IA VCC
32 AOUTA D(GB) 2 STX 17 LED IA OUT
33 GND 1 STX 16 UNREG GND
34 LGAMP D
TOP P.C.B.
UNIT
42 HCK D 69 TRAN R 7 UNREG
FLASH
43 GND 68 ETRAN R 6 UNREG
44 SIGRS D 67 LGCELEXT R 5
45 GND 66 DP U R 4 UNREG UNREG
65 CCL U R 3
64 LGCEL U R 2 UNREG UNREG
63 GND 1
62 MPXLOW U R UNREG
61 GND
(COMPONENT SIDE)
60 SFIUPCNT R
FP3913 59 ICNTCOL R
58 VDDCEL U R
1 GND 57 PWB U R
2 RS2 D 56 PWB U R
MAICO FPC
3 RS1 D 55 GND
4 5SKIP D 54 CLDCNC U R
53 AVDD U
1
2
3
4
LENS UNIT
MOUNT BOX UNIT
5 5SKIPS D 52 AVDD U
6 HST D 51 GND
7 NCSH D
S-4
50 AOUTB U(GB)
2
1
8 VDRRS D
2
1
9 NCCL D 49 GND
10 DVDD D 48 AOUTA U(B)
11 SWB D 47 GND
12 SWA D 46 LGAMP U
13 3MIX D 45 GND
14 RSD D L 44 RSD U R
FP8002
15 GND 43 CGCH1 U
16 GND 42 CGCH2 U
REG GND
41 VMIX2
PON ON L
17 GND
CMD DIAL0
CMD DIAL1
P8503
P8502
18 CLDCNC D L 40 VMIX1
39 OUTAMPCL U
LUMP+
LUMP-
TRG IN
19 GND 38 HCK U
20 PWB D L 37 GND
21 PWB D L
UNREG GND
22 VDDCEL D L 36 SIGRS U
23 SLIMIT1 D L 35 GND
24 SLIMIT2 D L 34 RS2 U
25 LOADCELL D 33 RS1 U
26 MPXLOW D L 32 5SKIP U
27 GND 31 5SKIPS U
28 LGCEL D L 30 HST U P8001
29 CCL D L 29 NCSH U
30 DP D L 28 VDRRS U
31 SFRST 27 NCCL U 4 BAT +
32 SRRST L 26 DVDD U
33 RDCEL L 25 SWB U 3 BAT THERMO
34 V1 L 24 SWA U
35 V2 L 23 2MIX 2 BAT DET
36 22 RSD U L
(SSWF)
44 DVDD L 14 SFIUPCNT L
(FOIL SIDE) 45 GND 12 MPXLOW U L
13
11
LOADCELL U
GND
10 LGCEL U L
FLASH P.C.B.
9 CCL U L
8 DP U L
7 LGCELEXT L
6 FDUP
FP8501 FP9009 5 GND
4 ETRAN L
10 PW D4R8V 1 UNREG 3 TRAN L
SSWF FPC
2 UNREG 2 ERSCEL L
9 STB CHG LV 3 UNREG 1 VSRC L
4 UNREG
LENS FPC
2 UNREG 17
MAIN STB FPC
17 CMD DIAL0
11
45
41
39
37
35
33
31
29
25
23
21
19
17
15
13
16 SHUTTER HALF
15 SHUTTER FULL
14 LED IA VCC
13 LED IA OUT
NC
VDD
GND
GND
GND
GND
GND
GND
GND
SCLK
VALID
DATA8
DATA6
DATA4
DATA2
DATA0
12 UNREG GND
RESET
VSYNC
DATA14
DATA12
DATA10
11 UNREG GND
43 VCC(3V-SW)
27 VIO VIDEO(D1R8V)
10 UNREG GND
9 UNREG GND
8
6
4
2
44
40
38
34
32
30
28
26
24
22
20
18
16
14
12
10
FP9003
8 UNREG GND
LVF UNIT
7 BAT DET
POWER FPC
6 BAT THERMO
9
7
5
3
1
11
23
21
19
17
15
13
5 UNREG
SEN
VDD
VDD
GND
GND
GND
GND
GND
GND
4 UNREG
SDAT
DATA9
DATA7
DATA5
DATA3
DATA1
CLOCK
HSYNC
DATA11
DATA15
DATA13
3 UNREG
42 VCC(3V-SW)
2 UNREG
36 VIO SERIAL(D3V)
1 UNREG
GND
GND
GND
GND
LSCK
LSL2B
LSLDP
LSRST
LEN4R2V
LEN4R2V
LEN4R2V
LEN4R2V
FP9010
8
6
4
2
22
20
18
16
14
12
10
15 MIC 4R5V
FP9001
14 MIC 4R5V
12 MIC R IN 13 MIC GND
10 MIC GND 11 MIC L IN
8 INT DET SW 9 MIC TR BIAS
6 D GND 7 D GND TOP OP FPC
GND
GND
GND
GND
LSB2A
LSDIO
LSB2L
LSDET
4 D GND 5 POWER ON L
LEN4R2V
LEN4R2V
LEN4R2V
5 NC
4 CROSS KEY IN
(FOIL SIDE)
MAIN P.C.B.
5 MIC LIN
ECM LIN
ECM RIN
MIC GND
MIC GND
4 MIC GND
FP4202
3 MIC TR BIAS
2 INT DET SW
MIC P.C.B.
1 D GND
(FOIL SIDE)
6 GND
5 REAR KEYIN2
4 REAR KEYIN1
3 CROSS KEY IN
FP9008
2 NC
1 GND
REAR OP P.C.B.
STEREO
(COMPONENT SIDE)
MIC FPC
MICROPHONE
UNREG 6
CC8002
UNREG 7
BAT_THERMO ON_BOARD_CONTACT
BAT_THERMO 8 IPS-4077T-01Y900
BAT_DET
BAT_DET 9 K4AC01D00001
ET8001
UNREG_GND 10
UNREG_GND 11
$[D4ED18R0A014]
$[D4ED18R0A014]
UNREG_GND 12
UNREG_GND 13
S8002
UNREG_GND 14
VA8005
VA8006
K0F212A00006
UNREG_GND 15 5
UNREG_GND 16 D8001
IA_LED(BLUE) S8001
D LED_IA_OUT 17
LED_IA_OUT
LED_IA_VCC
B3AEB0000141
K0F111A00591 2 1
LED_IA_VCC 18 S1
$[D4ED18R0A014]
SHUTTER_FULL 3 1
SHUTTER_FULL 19
SHUTTER_HALF
VA8002
SHUTTER_HALF 20
CMD_DIAL0
CMD_DIAL0 21 4 2 4 3
CMD_DIAL1
CMD_DIAL1 22 S2
TOP_KEY_IN IA 6
TOP_KEY_IN 23
G2
FP8002 K1MY04BA0370
C Molex/503480-0400
BackLock/BottomContact
G2
10k
4 CMD_DIAL1
3 REG_GND
R8004
2 PON_ON_L
$[D4ED18R0A014]
$[D4ED18R0A014]
$[D4ED18R0A014]
1 CMD_DIAL0
G1
VA8001
VA8003
VA8004
A
DMC-G3/G3K/G3W
Top Operation
Schematic Diagram
1 2 3 4 5 6 7 8 9 10
S-5
S4.3. Flash Schematic Diagram
1
250V 1M[36] 4 UNREG_GND
G2 910K[D][22]
LUMP+ 2 C8507 5 INT_STB_TRG
F1J1A106A023 6 STB_PWM_OUT
E LUMP- 1 R8507
10V
D8501 [FPSN4TP] [22] 7 UNREG_GND
G1 910K[D][22]
2
8 UNREG_GND
B0ECGP000006
C8510 CL8505 9 STB_CHG_LV
1 R8508 1
Q8502
F2A2F1710001 300K[D] C8504 10 PW_D4R8V
B1DFCG000020 R8513
2 F1K2J102A028 OR
315V
630V
Q8501
B1JBLP000022 [36] 22
1 2 3
4
RL8503 D
R8511
R8509 G 15K
RL8501 R8501
100K[36] 16K[D] S
[36]
F1K2J333A029
D
8
5
6 5 4
630V
C8501
R8503
100K
G2
UNREG_GND 2
TRG_IN 1 R8514
G1 4.7K[36]
CL8503
P8502
K1KA02ZA0001
(SM02B-SSR-H-ETB(LF)(SN)) R8504
22[18]
3 4
C R8510
1K
2 5 CL8504
QR8502
1 6 B1GBCFGJ0021
R8505
C8506
10V
100[18] QR8501
1u[18]
B1GKCFJN0008
A
DMC-G3/G3K/G3W
Flash
Schematic Diagram
1 2 3 4 5 6 7 8 9 10
S-6
S4.4. Rear Operation Schematic Diagram
DISP
R7550
$ TO MAIN-PCB
R7551
10K
1
SET FP7550
K1MN06BA0272
06FKZ-SM1-GAN-1-ETB(LF)(SN) / JST
ZIF-TYPE/ TOP contact
F PLAY
R7552
G2
2.4K
$
R7553
6 GND
PLAY REC 1
5 NC
S7551 S7550
REC
4 CROSS_KEY_IN
K0F111A00595 K0F111A00591
3 REAR_KEYIN1
R7554
3.9K
4 2 4 2 2 REAR_KEYIN2
1 GND
QMENU
3 1 3 1 G1
E RIGHT
DISP/Fn1
R7555
R7556
2.4K
S7552 $
1
K0F111A00595 REC DISP/Fn1
UP
4 2
3.9K
R7557
3 1
LEFT
UP
7.5K
R7559
DOWN PLAY
MENU/SET
D RIGHT
UP DOWN RIGHT LEFT MENU/SET
S7557 S7556 S7555 S7554 S7553
K0F111A00595 K0F111A00595 K0F111A00595 K0F111A00595 K0F111A00595 LEFT
4 2 4 2 4 2 4 2 4 2
DOWN
3 1 3 1 3 1 3 1 3 1
QMENU/Fn2/DEL
(View)
C QMENU/Fn2/DEL
S7558
K0F111A00595
4 2
3 1
GND
Confidential
Until
A
DMC-G3/G3K/G3W
Rear Operation
Schematic Diagram
1 2 3 4 5 6 7 8 9 10
S-7
S4.5. MIC Schematic Diagram
POP UP DET SW
(SPVN310100(ALPS))
2 1
Normaly-Open_SW
K0L1BA000159
F
S4201
$[D4ED18R00004]
3 4
VA4203
Connect emitter to collector shortest
ERA3YED392V
ERA3YED392V
FP4201 R4204
3.9k[18]
3.9k[18]
FPC CONTACT to TOP_OP_FPC
B1ABDF000017
100K[18]
R4201
R4202
F1G1A1040006
C4207 0.1u
G1 ERA3YKD104V
Q4201
MIC_GND 1 C4203 R4203 G1
6.3V
10V
ECM_LIN 2 1 D_GND
ECM_RIN 3 1u 1k 2 INT_DET_SW
$[F1G1H5610004]
MIC_GND 4 F1G0J1050007 3 MIC_TR_BIAS
$[D4ED18R00004]
$[D4ED18R00004]
$[F1G1H330A565]
$[F1G1H330A565]
R4205
G2 4 MIC_GND
VA4201
VA4202
[560p]
1k
C4201
C4202
C4204
5 MIC_LIN
6 MIC_RIN
SHIELD by MIC_GND MIC_GND
7
R4207 8 MIC_4R5V
B1ABDF000017
100K[18]
D G2
F1G1A1040006
C4208 0.1u
ERA3YKD104V SHIELD by MIC_GND
Q4202
C42056.3V R4206
Connect emitter to collector shortest
10V
1u 1k
$[F1G1H5610004]
F1G0J1050007
R4208
1k
[560p]
C4206
C
Confidential
Until
A
DMC-G3/G3K/G3W
MIC
Schematic Diagram
1 2 3 4 5 6 7 8 9 10
S-8
S5. Print Circuit Board
S5.1. Top P.C.B.
G
ET8001
1234
23 15 5 1
FP8002
FP8001
F
20 22 10 2
VA8003
VA8001
VA8004
R8004
LB8001
P8001
F8001
E
4 3 2 1
(Component Side)
D
1
D8001
S8001
VA8002
3
C
VA8006
3
VA8005
6
5
S8002
C8001
4
2
CC8002
B R8001
CC8001
(Foil Side)
A
DMC-G3/G3K/G3W
Top P.C.B.
1 2 3 4 5 6 7 8 9 10
S-9
S5.2. Flash P.C.B.
G P8502
2 1
P8503
2 1
C8502
R8514
D8501
CL8502
C8501
R8501
R8512
E 4 1 654
3 2 Q8502
123
T8501
R8513
R8511
Q8501
CL8501
CL8505
5 8 4 1
D D8503
D8502
R8503
C8504 C8507
R8505
R8504
C8506
R8506
R8507
1 2 3
10
C QR8501
CL8503
6 5 4
R8510
R8508
FP8501
QR8502
5
CL8504
e
R8509
F8501
1
B
RL8501 RL8503
C8510
DMC-G3/G3K/G3W
(Component Side) (Foil Side) Flash P.C.B.
1 2 3 4 5 6 7 8 9 10
S-10
S5.3. Rear Operation P.C.B.
4
S7551
S7550
1
2
F
4
S7552
2
D S7557
R7559
R7557
R7556
R7555
4 2
65 1
R7554
R7553
R7552
R7550 FP7550 3 1
R7551
4
S7554
S7553
S7555
C
2
S7556
4 2
3 1
4
B
S7558
2
A
(Component Side) (Foil Side)
DMC-G3/G3K/G3W
Rear Operation P.C.B.
1 2 3 4 5 6 7 8 9 10
S-11
S5.4. MIC P.C.B.
1 4
S4201
2 3
VA4203
E FP4202
C4208 R4208 8 5 1
e
R4207
C4206
Q4202
R4206
R4202
D
C4205
VA4202
C4202
1234
FP4201
C4203
VA4201
C4201
R4203
R4201
C4204
R4204 C4207
Q4201
e
C
R4205
DMC-G3/G3K/G3W
MIC P.C.B.
1 2 3 4 5 6 7 8 9 10
S-12
S6. Replacement Parts List
S-13
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
C8501 F1K2J333A029 C.CAPACITOR 630V 0.033U 1 R4201 ERA3YED392V M.RESISTOR 1/16W 3.9K 1
C8502 F1K2E2230002 C.CAPACITOR 250V 0.022U 1 R4202 ERA3YED392V M.RESISTOR 1/16W 3.9K 1
C8504 F1K2J102A028 C.CAPACITOR 630V 1000P 1 R4203 D0GA102JA023 CHIP RESISTOR 1
C8506 F1H1A105A025 C.CAPACITOR CH 10V 1U 1 R4204 ERA3YKD104V M.RESISTOR 1/16W 100K 1
C8507 F1J1A106A043 C.CAPACITOR CH 10V 10U 1 R4205 D0GA102JA023 CHIP RESISTOR 1
R4206 D0GA102JA023 CHIP RESISTOR 1
D8501 B0ECGP000006 DIODE 1 E.S.D. R4207 ERA3YKD104V M.RESISTOR 1/16W 100K 1
D8502 B0HCMP000006 DIODE 1 E.S.D. R4208 D0GA102JA023 CHIP RESISTOR 1
D8503 DA2JF8100L DIODE 1 E.S.D.
S4201 K0L1BA000159 SWITCH 1
F8501 ERBSE1R50U FUSE 32V 1.5A 1
S-14
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
40 VEP59096A LCD IF P.C.B. 1 (RTL) E.S.D.
1 VEP56135B MAIN P.C.B. 1 (RTL) E.S.D. EG,EC,EB, 41 VGQ0V38 LCD BL BEZEL SHEET 1
KEG,KEC,KEB,WEG,WEC,WEB 42 VGQ0Y08 LCD PCB SHEET 1
1 VEP56135A MAIN P.C.B. 1 (RTL) E.S.D. 43 VGQ0Y08 LCD PCB SHEET 1
PP,PC,EE,GC,GH,GT,GN,GD, 44 VKM9409 LCD CASE TOP 1 (-K,-KA)
KPP,KPC,KEE,KGC,KGH,KGT, 44 VKM9412 LCD CASE TOP 1 (-W)
KGK,KGN,KGD,WPP,WEE,WGC, 44 VKM9411 LCD CASE TOP 1 (-T)
WGH,WGT,WGK,WGN,WGD 44 VKM9410 LCD CASE TOP 1 (-R)
2 ML-421S/DN BATTERY 1 [ENERGY] (B9110) 45 VKM9413 LCD CASE BOTTOM 1 (-K)
3 VGK3763 SIDE ORNAMENT L 1 (-K,-T,-R,-KA) 45 VKM9416 LCD CASE BOTTOM 1 (-W)
3 VGK3764 SIDE ORNAMENT L 1 (-W) 45 VKM9415 LCD CASE BOTTOM 1 (-T)
4 VGK3765 SIDE ORNAMENT R 1 (-K,-T,-R,-KA) 45 VKM9414 LCD CASE BOTTOM 1 (-R)
4 VGK3766 SIDE ORNAMENT R 1 (-W) 45 VKM9614 LCD CASE BOTTOM 1 (-KA)
5 VGQ0V34 EYE RUBBER 1 46 VYK5G82 LCD UNIT 1
6 VGQ0V35 EYE CUP BASE 1 50 VYK5B79 LCD HINGE UNIT 1 (-K,-KA)
7 VGQ0X52 LENS FPC BUSTERAID 1 50 VYK5B82 LCD HINGE UNIT 1 (-W)
8 VGQ0Y02 TAPE 1 50 VYK5B81 LCD HINGE UNIT 1 (-T)
9 VGQ0Y02 TAPE 1 50 VYK5B80 LCD HINGE UNIT 1 (-R)
10 VGQ0Y02 TAPE 1 56 VGQ0V89 CAPACITOR PCB COVER 1
11 VGQ0Y03 TAPE 1 57 VYK5B78 TOP CASE UNIT 1 (-K,-T,-R,-KA)
12 VKF4888 JACK DOOR 1 (-K,-T,-R,-KA) 57 VYK5C72 TOP CASE UNIT 1 (-W)
12 VKF4889 JACK DOOR 1 (-W) 59 VMC2111 SHOE SPRING 1
13 VMT2182 HEAT RADIATION PAD1 1 60 K0RC00800003 MULTI-BUTTON SWITCH 1
14 VMT2183 HEAT RADIATION PAD2 1 61 VEK0R79 MICROPHONE UNIT 1
15 VMT2184 HEAT RADIATION PAD3 1 62 VEK0R81 FLASH UNIT 1
16 VXQ2142T MOUNT BOX UNIT 1 [SPC] 63 VEP54024A MIC P.C.B. 1 (RTL) E.S.D.
17 VYK5B51 FRONT CASE UNIT 1 (-K,-KA) 64 VEP56137A TOP P.C.B. 1 (RTL) E.S.D.
17 VYK5B54 FRONT CASE UNIT 1 (-W) 65 VGQ0R32 MIC CUSHION (B) 1
17 VYK5B53 FRONT CASE UNIT 1 (-T) 66 VGQ0R33 MIC CUSHION (C) 1
17 VYK5B52 FRONT CASE UNIT 1 (-R) 67 VGQ0W43 MIC CUSHION (A) 1
17-1 VGK3760 GRIP PIECE FRONT 1 (-K,-KA) 68 VKM9421 FLASH CASE TOP 1 (-K,-T,-R,-KA)
17-1 VGK3788 GRIP PIECE FRONT 1 (-W) 68 VKM9422 FLASH CASE TOP 1 (-W)
17-1 VGK3787 GRIP PIECE FRONT 1 (-T) 69 VWJ2266 MAIN_POW_FPC 1
17-1 VGK3770 GRIP PIECE FRONT 1 (-R) 71 VGQ0R70 CAPACITOR TAPE 1
17-2 VGK3792 MOUNT RING 1 (-K,-T,-R,-KA) 72 VGQ0W48 SHEET 1
17-2 VGK3793 MOUNT RING 1 (-W) 73 VGQ0W48 SHEET 1
17-3 VGQ0V87 FRONT BLIND PIECE 1 74 VGU0H25 BATTERY LOCK KNOB 1
17-4 VGU0J48 LENS RELEASE BUTTON 1 (-K,-T,-R,-KA) 75 VKM9388 BATTERY FRAME 1
17-4 VGU0K13 LENS RELEASE BUTTON 1 (-W) 76 VMB4304 BATTERY LOCK SPRING 1
17-5 VMB4504 LENS RELEASE BUTTON SPRING 1 77 VMB4500 BATTERY DOOR SPRING 1
17-6 VMP9970 LENS RELEASE FIX PLATE 1 78 VMB4509 BATTERY OUT SPRING 1
17-7 VMP9995 MOUNT RING PLATE 1 79 VMP9955 BATTERY CASE 1
17-8 VGQ0H89 CUSHION 1 80 VMP9956 SIDE FRAME R 1
17-9 VGQ0H89 CUSHION 1 81 VMP9957 TRIPOD 1
18 VEK0R80 HINGE SW FPC UNIT 1 82 VMP9958 HEAT RADIATION PLATE 1
21 VKM9393 ARM COVER TOP 1 (-K,-KA) 83 VMS8177 BATTERY DOOR SHAFT 1
21 VKM9396 ARM COVER TOP 1 (-W) 84 F2A2F1710001 E.CAPACITOR 1 (C8510)
21 VKM9395 ARM COVER TOP 1 (-T) 85 VEE1K29 CAPACITOR GND HARNESS 1
21 VKM9394 ARM COVER TOP 1 (-R) 86 VEP56136A FLASH P.C.B. 1 (RTL) E.S.D.
22 VKM9397 ARM COVER BOTTOM 1 (-K,-KA) 87 VMB4508 CAPACITOR EARTH SPRING 1
22 VKM9400 ARM COVER BOTTOM 1 (-W) 88 VYK5B91 BATTERY DOOR UNIT 1 (-K,-KA)
22 VKM9399 ARM COVER BOTTOM 1 (-T) 88 VYK5B94 BATTERY DOOR UNIT 1 (-W)
22 VKM9398 ARM COVER BOTTOM 1 (-R) 88 VYK5B93 BATTERY DOOR UNIT 1 (-T)
23 VMP0A03 HINGE SW PLATE B 1 88 VYK5B92 BATTERY DOOR UNIT 1 (-R)
24 VMP9961 HINGE PLATE 1 89 VYQ6831 LVF UNIT 1
25 VMP9998 HINGE SW PLATE A 1 89-1 VKM9429 LVF COVER 1
26 VEP50086A REAR OPERATION P.C.B. 1 (RTL) 90 L5EDDYY00255 LVF MODULE 1
27 VGQ0V32 GRIP PIECE REAR 1 (-K,-T,-R,-KA) 91 VGQ0W20 LVF FPC FIX TAPE 1
27 VGQ0V33 GRIP PIECE REAR 1 (-W) 92 VWJ2267 MAIN FLASH FPC 1
28 VGQ0V36 LCD LOCK PIECE 1 93 VWJ2271 LVF FPC 1
29 VGQ0W26 LCD LOCK HOLDER 1 93-1 VGQ0P70 LVF FPC FIX TAPE 1
30 VGU0J50 LVF/LCD BUTTON 1 (-K,-T,-R,-KA) 94 VGQ0Y27 CUSHION 1
30 VGU0K16 LVF/LCD BUTTON 1 (-W)
31 VGU0J51 PLAYBACK/MOTION PICTURE BUTTON 1 (-K,-T,-R,-KA) B1 VHD2149 SCREW 1 (-K,-T,-R,-KA)
31 VGU0K15 PLAYBACK/MOTION PICTURE BUTTON 1 (-W) B1 VHD2019 SCREW 1 (-W)
32 VGU0J53 MOTION PICTURE PIECE 1 B2 VHD2149 SCREW 1 (-K,-T,-R,-KA)
33 VGU0K00 REAR OPERATION BUTTON 1 (-K,-T,-R,-KA) B2 VHD2019 SCREW 1 (-W)
33 VGU0K14 REAR OPERATION BUTTON 1 (-W) B3 VHD2149 SCREW 1 (-K,-T,-R,-KA)
34 VMB4373 LCD LOCK SPRING 1 B3 VHD2019 SCREW 1 (-W)
35 VMP0A41 REC EARTH PLATE 1 B4 VHD2149 SCREW 1 (-K,-T,-R,-KA)
36 VMP9960 REAR EARTH PLATE 1 B4 VHD2019 SCREW 1 (-W)
37 VMP9968 REAR OPERATION EARTH PLATE 1 B5 VHD2149 SCREW 1 (-K,-T,-R,-KA)
38 VWJ2268 REAR OPEARTION FFC 1 B5 VHD2019 SCREW 1 (-W)
39 VYK5B67 REAR CASE UNIT 1 (-K,-KA) B6 VHD2149 SCREW 1 (-K,-T,-R,-KA)
39 VYK5B70 REAR CASE UNIT 1 (-W) B6 VHD2019 SCREW 1 (-W)
39 VYK5B69 REAR CASE UNIT 1 (-T) B7 VHD2286 SCREW 1
39 VYK5B68 REAR CASE UNIT 1 (-R) B8 VHD2331-A SCREW 1
S-15
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
B9 VHD2331-A SCREW 1
B10 VHD2331-A SCREW 1
B11 VHD2331-A SCREW 1
B12 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B12 VHD2338 SCREW 1 (-W)
B13 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B13 VHD2338 SCREW 1 (-W)
B14 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B14 VHD2338 SCREW 1 (-W)
B15 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B15 VHD2338 SCREW 1 (-W)
B16 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B16 VHD2338 SCREW 1 (-W)
B17 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B17 VHD2338 SCREW 1 (-W)
B18 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B18 VHD2338 SCREW 1 (-W)
B19 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B19 VHD2338 SCREW 1 (-W)
B20 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B20 VHD2338 SCREW 1 (-W)
B21 VHD2337 SCREW 1 (-K,-T,-R,-KA)
B21 VHD2338 SCREW 1 (-W)
B22 VHD1909 SCREW 1
B23 VHD1909 SCREW 1
B24 XQN16+BJ4FN SCREW 1
B25 XQN16+BJ4FN SCREW 1
B26 XQN16+BJ4FN SCREW 1
B27 XQN16+BJ4FN SCREW 1
B30 VHD2332 SCREW 1
B31 VHD2332 SCREW 1
B32 VHD2332 SCREW 1
B33 VHD2332 SCREW 1
B34 VHD2091 SCREW 1
B35 VHD2091 SCREW 1
B36 VHD2190 SCREW 1
B37 VHD2190 SCREW 1
B38 VHD1998 SCREW 1
B39 XQN16+BJ4FN SCREW 1
B40 XQN16+BJ4FN SCREW 1
B41 XQN16+BJ4FN SCREW 1
B42 XQN16+BJ4FN SCREW 1
B43 XQN16+BJ4FN SCREW 1
B44 VHD2179 SCREW 1 (-K,-T,-R,-KA)
B44 VHD2200 SCREW 1 (-W)
B45 VHD2179 SCREW 1 (-K,-T,-R,-KA)
B45 VHD2200 SCREW 1 (-W)
B46 VHD2333 SCREW 1 (-K,-T,-R,-KA)
B46 VHD2102 SCREW 1 (-W)
B47 VHD2333 SCREW 1 (-K,-T,-R,-KA)
B47 VHD2102 SCREW 1 (-W)
B48 VHD2335 SCREW 1
B49 VHD2335 SCREW 1
B50 XQN14+BJ4FJK SCREW 1
B51 XQN14+BJ4FJK SCREW 1
B52 XQN14+BJ4FJK SCREW 1
B53 XQN14+BJ4FJK SCREW 1
B54 XQN14+BJ4FJK SCREW 1
B55 XQN14+BJ4FJK SCREW 1
B56 XQN14+BJ4FJK SCREW 1
B57 XQN14+BJ4FJK SCREW 1
B58 VHD1996 SCREW 1
B59 VHD1996 SCREW 1
B60 VHD2019 SCREW 1
B61 VHD2286 SCREW 1
B62 XQN16+B3FN SCREW 1
B63 XQN16+B3FN SCREW 1
B64 XQN16+B3FN SCREW 1
S-16
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
S-17
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
S-18
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
411 VQT3N54 BASIC O/I 1 KGN
400 VKF4385 BODY CAP 1 (G3K) (ENGLISH)
401 VPF1316A CAMERA BAG 1 (G3K) 411 VQT3N55 BASIC O/I 1 KGD
402 DE-A94AA/SX BATTERY CHARGER 1 KEG,KEC,KEB,KEE,KGN (KOREAN)
402 DE-A93BA/SX BATTERY CHARGER 1 KPP,KPC 411 VQT3N53 BASIC O/I 1 KGK
402 DE-A94BB/SX BATTERY CHARGER 1 KGC,KGH,KGK,KGD (CHINESE(SIMPLIFIED))
402 DE-A94CA/SX BATTERY CHARGER 1 KGT 413 VPK5005 PACKING CASE 1 KPP,KPC
403 ----- BATTERY 1 KEG,KEC,KEB,KEE,KGC,KGH, 413 VPK5006 PACKING CASE 1 KEG,KEC,KEB,KEE,KGC,KGH,
KGT,KGN,KGD,KGK,KPP,KPC KGT,KGN,KGD
404 K1HY08YY0015 USB CABLE W/PLUG 1 (G3K) 413 VPK5007 PACKING CASE 1 KGK
405 K1HY08YY0016 AV CABLE W/PLUG 1 (G3K) 414 VPN7251 PAD A 1 (G3K)
406 VFC4634 SHOULDER STRAP 1 KPP,KPC,KEG,KEC,KEB,KEE, 415 VPN7253 PAD D 1 KPP,KPC,KEG,KEC,KEB,KEE,
KGC,KGH,KGT,KGK,KGN,KGD KGC,KGH,KGT,KGK,KGN,KGD
407 VFF0806 CD-ROM (INSTRUCTION BOOK) 1 KEG,KEC,KEB 416 VPN7252 PAD B 1 KPP,KPC,KEG,KEC,KEB,KEE,
407 VFF0805 CD-ROM (INSTRUCTION BOOK) 1 KPP,KPC KGC,KGH,KGT,KGK,KGN,KGD
407 VFF0807 CD-ROM (INSTRUCTION BOOK) 1 KEE,KGC,KGH,KGN 417 VQL2C67-A OPERATING LABEL 1 KPC
407 VFF0808 CD-ROM (INSTRUCTION BOOK) 1 KGT,KGD 417 VQL2C68-1A OPERATING LABEL 1 KGT
407 VFF0809 CD-ROM (INSTRUCTION BOOK) 1 KGK 418 VQL2J61 GD LABEL 1 KGD
408 VGQ0C14 TOUCH PEN 1 (G3K) 419 VQL1Z76 NTSC LABEL 1 KGT,KGD
409 VPF1100 BAG, POLYETHYLENE 1 (G3K) 421 VQL2H32 COLOR LABEL 1 KPP-W
410 VQC8410 O/I SOFTWARE 1 KEG 421 VQL2M24 COLOR LABEL 1 KPP-T
(GERMAN/FRENCH/ITALIAN/ 421 VQL1Z66 COLOR LABEL 1 KPP-R,KPC-R
DUTCH) 421 VQL2M25 COLOR LABEL 1 KEG-T,KGC-T
410 VQC8408 O/I SOFTWARE 1 KPP 421 VQL1Z69 COLOR LABEL 1 KEG-R,KEC-R,KEB-R,KEE-R,
(ENGLISH/SPANISH/ KGC-R,KGH-R,KGN-R
PORTUGUESE) 421 VQL2B13 COLOR LABEL 1 KEC-W,KEB-W,KEE-W,KGC-W,
410 VQC8409 O/I SOFTWARE 1 KPC KGH-W,KGT-W,KGN-W,KGD-W
(ENGLISH/CANADIAN FRENCH) 421 VQL2H31 COLOR LABEL 1 KGK-W
417 VQC8411 O/I SOFTWARE 1 KEC 421 VQL2F42 COLOR LABEL 1 KGK-R
(SPANISH/PORTUGUESE/ 422 VQL2H32 COLOR LABEL 1 KPP-W
SWEDISH/DANISH/FINNISH) 422 VQL2M24 COLOR LABEL 1 KPP-T
410 VQC8412 O/I SOFTWARE 1 KEB,KGN 422 VQL1Z66 COLOR LABEL 1 KPP-R,KPC-R
(ENGLISH) 422 VQL2M25 COLOR LABEL 1 KEG-T,KGC-T
410 VQC8413 O/I SOFTWARE 1 KEE 422 VQL1Z69 COLOR LABEL 1 KEG-R,KEC-R,KEB-R,KEE-R,
(RUSSIAN/UKRAINIAN) KGC-R,KGH-R,KGN-R
410 VQC8414 O/I SOFTWARE 1 KGC,KGH 422 VQL2B13 COLOR LABEL 1 KEC-W,KEB-W,KEE-W,KGC-W,
(ENGLISH/ KGH-W,KGT-W,KGN-W,KGD-W
CHINESE(TRADITIONAL)/ 422 VQL2H31 COLOR LABEL 1 KGK-W
ARABIC) 422 VQL2F42 COLOR LABEL 1 KGK-R
410 VQC8415 O/I SOFTWARE 1 KGT 423 VQL2H32 COLOR LABEL 1 KPP-W
(CHINESE(TRADITIONAL)) 423 VQL2M24 COLOR LABEL 1 KPP-T
410 VQC8417 O/I SOFTWARE 1 KGD 423 VQL1Z66 COLOR LABEL 1 KPP-R,KPC-R
(KOREAN) 423 VQL2M25 COLOR LABEL 1 KEG-T,KGC-T
410 VQC8416 O/I SOFTWARE 1 KGK 423 VQL1Z69 COLOR LABEL 1 KEG-R,KEC-R,KEB-R,KEE-R,
(CHINESE(SIMPLIFIED)) KGC-R,KGH-R,KGN-R
411 VQT3N43 BASIC O/I 1 KEG 423 VQL2B13 COLOR LABEL 1 KEC-W,KEB-W,KEE-W,KGC-W,
(GERMAN/FRENCH) KGH-W,KGT-W,KGN-W,KGD-W
411 VQT3N44 BASIC O/I 1 KEG 423 VQL2H31 COLOR LABEL 1 KGK-W
(ITALIAN/DUTCH) 423 VQL2F42 COLOR LABEL 1 KGK-R
411 VQT3N40 BASIC O/I 1 KPP 424 VFC4315 LENS REAR CAP 1 (G3K) [SPC]
(ENGLISH/SPANISH) 425 VYF3201 LENS CAP 1 (G3K) [SPC]
411 VQT3N41 BASIC O/I 1 KPP 426 VPF1438 LENS BAG 1 (G3K) [SPC]
(PORTUGUESE) 427 VYC1009 LENS HOOD 1 (G3K) [SPC]
411 VQT3N42 BASIC O/I 1 KPC 450 K2CT3YY00034 AC CORD W/PLUG 1 KEB,KGC,KGH
(ENGLISH/CANADIAN FRENCH) 451 K2CQ2YY00082 AC CORD W/PLUG 1 KEG,KEC,KEE,KGC
411 VQT3N45 BASIC O/I 1 KEC 451 K2CR2YY00026 AC CORD W/PLUG 1 KGD
(SPANISH/PORTUGUESE) 453 K2CA2YY00129 AC CORD W/PLUG 1 KGT
411 VQT3N46 BASIC O/I 1 KEC 453 K2CA2YY00130 AC CORD W/PLUG 1 KGK
(SWEDISH/DANISH) 454 K2CJ2YY00052 AC CORD W/PLUG 1 KGN
411 VQT3N47 BASIC O/I 1 KEC 460 VFF0800-S CD-ROM(APPLI-OVERSEAS) 1 KPP,KPC,KEG,KEC,KEB,KEE,
(FINNISH) KGC,KGH,KGT,KGN,KGD
411 VQT3N48 BASIC O/I 1 KEB [SPC]See "Notes"
(ENGLISH) 460 VFF0801-S CD-ROM (APPLI-CHINA) 1 KGK [SPC] See "Notes"
411 VQT3N49 BASIC O/I 1 KEE
(RUSSIAN/UKRAINIAN)
411 VQT3N50 BASIC O/I 1 KGC,KGH
(ENGLISH/
CHINESE(TRADITIONAL))
411 VQT3N51 BASIC O/I 1 KGC
(ARABIC)
411 VQT3N52 BASIC O/I 1 KGT
(CHINESE(TRADITIONAL))
S-19
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
513 VPK5009 PACKING CASE 1 WPP-K
500 VKF4385 BODY CAP 1 (G3W) 513 VPK5010 PACKING CASE 1 WEG,WEC,WEB-K/R,WEE-K,
501 VPF1316A CAMERA BAG 1 (G3W) WGC,WGH,WGT,WGN,WGD
502 DE-A94AA/SX BATTERY CHARGER 1 WEG,WEC,WEB,WEE,WGN 513 VPK5081 PACKING CASE 1 WEB-KA
502 DE-A93BA/SX BATTERY CHARGER 1 WPP 513 VPK5011 PACKING CASE 1 WGK
502 DE-A94BB/SX BATTERY CHARGER 1 WGC,WGH,WGK,WGD 514 VPN7251 PAD A 1 (G3W)
502 DE-A94CA/SX BATTERY CHARGER 1 WGT 515 VPN7254 PAD C 1 WPP,WEG,WEC,WEB,WEE,WGC,
503 ----- BATTERY 1 WEG,WEC,WEB,WEE,WGN,WGC, WGH,WGT,WGK,WGN,WGD
WGH,WGK,WGD,WGT,WPP 516 VPN7252 PAD B 1 WPP,WEG,WEC,WEB,WEE,WGC,
504 K1HY08YY0015 USB CABLE W/PLUG 1 (G3W) WGH,WGT,WGK,WGN,WGD
505 K1HY08YY0016 AV CABLE W/PLUG 1 (G3W) 517 VQL2C68-1A OPERATING LABEL 1 WGT
506 VFC4634 SHOULDER STRAP 1 WPP,WEG,WEC,WEB-K/R,WEE-K, 518 VQL2J61 GD LABEL 1 WGD
WGC,WGH,WGT,WGN,WGD,WGK 519 VQL1Z76 NTSC LABEL 1 WGT,WGD
506 VFC4717 SHOULDER STRAP 1 WEB-KA 521 VQL2M25 COLOR LABEL 1 WEG-T,WGC-T
507 VFF0806 CD-ROM (INSTRUCTION BOOK) 1 WEG,WEC,WEB 521 VQL1Z69 COLOR LABEL 1 WEG-R,WEC-R,WEB-R,WGC-R,
507 VFF0805 CD-ROM (INSTRUCTION BOOK) 1 WPP WGH-R,WGN-R
507 VFF0807 CD-ROM (INSTRUCTION BOOK) 1 WEE,WGC,WGH,WGN 521 VQL2B13 COLOR LABEL 1 WEC-W,WGC-W,WGH-W,WGT-W,
507 VFF0808 CD-ROM (INSTRUCTION BOOK) 1 WGT,WGD WGN-W,WGD-W
507 VFF0809 CD-ROM (INSTRUCTION BOOK) 1 WGK 521 VQL2H31 COLOR LABEL 1 WGK-W
508 VGQ0C14 TOUCH PEN 1 (G3W) 521 VQL2F42 COLOR LABEL 1 WGK-R
509 VPF1100 BAG, POLYETHYLENE 1 (G3W) 522 VQL2M25 COLOR LABEL 1 WEG-T,WGC-T
510 VQC8410 O/I SOFTWARE 1 WEG 522 VQL1Z69 COLOR LABEL 1 WEG-R,WEC-R,WEB-R,WGC-R,
(GERMAN/FRENCH/ITALIAN/ WGH-R,WGN-R
DUTCH) 522 VQL2B13 COLOR LABEL 1 WEC-W,WGC-W,WGH-W,WGT-W,
510 VQC8408 O/I SOFTWARE 1 WPP WGN-W,WGD-W
(ENGLISH/SPANISH/ 522 VQL2H31 COLOR LABEL 1 WGK-W
PORTUGUESE) 522 VQL2F42 COLOR LABEL 1 WGK-R
510 VQC8411 O/I SOFTWARE 1 WEC 523 VQL2M25 COLOR LABEL 1 WEG-T,WGC-T
(SPANISH/PORTUGUESE/ 523 VQL1Z69 COLOR LABEL 1 WEG-R,WEC-R,WEB-R,WGC-R,
SWEDISH/DANISH/FINNISH) WGH-R,WGN-R
510 VQC8412 O/I SOFTWARE 1 WEB,WGN 523 VQL2B13 COLOR LABEL 1 WEC-W,WGC-W,WGH-W,WGT-W,
(ENGLISH) WGN-W,WGD-W
510 VQC8413 O/I SOFTWARE 1 WEE 523 VQL2H31 COLOR LABEL 1 WGK-W
(RUSSIAN/UKRAINIAN) 523 VQL2F42 COLOR LABEL 1 WGK-R
510 VQC8414 O/I SOFTWARE 1 WGC,WGH 524 VFC4315 LENS REAR CAP 1 (G3W) [SPC]
(ENGLISH/ 525 VYF3201 LENS CAP 1 (G3W) [SPC]
CHINESE(TRADITIONAL)/ 526 VPF1438 LENS BAG 1 (G3W) [SPC]
ARABIC) 527 VYC1009 LENS HOOD 1 (G3W) [SPC]
510 VQC8415 O/I SOFTWARE 1 WGT 528 VFC4315 LENS REAR CAP 1 (G3W) [SPC]
(CHINESE(TRADITIONAL)) 529 VYF3201 LENS CAP 1 (G3W) [SPC]
510 VQC8417 O/I SOFTWARE 1 WGD 530 VPF1316 LENS BAG 1 (G3W) [SPC]
(KOREAN) 531 VYC0986 LENS HOOD 1 (G3W) [SPC]
510 VQC8416 O/I SOFTWARE 1 WGK 550 K2CT3YY00034 AC CORD W/PLUG 1 WEB,WGC,WGH
(CHINESE(SIMPLIFIED)) 551 K2CQ2YY00082 AC CORD W/PLUG 1 WEG,WEC,WEE,WGC
511 VQT3N43 BASIC O/I 1 WEG 551 K2CR2YY00026 AC CORD W/PLUG 1 WGD
(GERMAN/FRENCH) 553 K2CA2YY00129 AC CORD W/PLUG 1 WGT
511 VQT3N44 BASIC O/I 1 WEG 553 K2CA2YY00130 AC CORD W/PLUG 1 WGK
(ITALIAN/DUTCH) 554 K2CJ2YY00052 AC CORD W/PLUG 1 WGN
511 VQT3N40 BASIC O/I 1 WPP 560 VFF0800-S CD-ROM(APPLI-OVERSEAS) 1 WPP,WEG,WEC,WEB,WEE,WGC,
(ENGLISH/SPANISH) WGH,WGT,WGN,WGD
511 VQT3N41 BASIC O/I 1 WPP [SPC] See "Notes"
(PORTUGUESE) 560 VFF0801-S CD-ROM (APPLI-CHINA) 1 WGK [SPC] See "Notes"
511 VQT3N45 BASIC O/I 1 WEC
(SPANISH/PORTUGUESE)
511 VQT3N46 BASIC O/I 1 WEC
(SWEDISH/DANISH)
511 VQT3N47 BASIC O/I 1 WEC
(FINNISH)
511 VQT3N48 BASIC O/I 1 WEB
(ENGLISH)
511 VQT3N49 BASIC O/I 1 WEE
(RUSSIAN/UKRAINIAN)
511 VQT3N50 BASIC O/I 1 WGC,WGH
(ENGLISH/
CHINESE(TRADITIONAL))
511 VQT3N51 BASIC O/I 1 WGC
(ARABIC)
511 VQT3N52 BASIC O/I 1 WGT
(CHINESE(TRADITIONAL))
511 VQT3N54 BASIC O/I 1 WGN
(ENGLISH)
511 VQT3N55 BASIC O/I 1 WGD
(KOREAN)
511 VQT3N53 BASIC O/I 1 WGK
(CHINESE(SIMPLIFIED))
S-20
DMC-G3EG-K vol.1
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
613 VPK5003 PACKING CASE 1 EG-K,EC-K,EB-K,EE-K,GC-K,
600 VKF4385 BODY CAP 1 (G3) GH-K,GT-K,GN-K,GD-K
601 VPF1316A CAMERA BAG 1 (G3) 613 VPK5002 PACKING CASE 1 PP-K,PC-K
602 DE-A94AA/SX BATTERY CHARGER 1 EG,EC,EB,EE,GN 614 VPN7251 PAD A 1 (G3)
602 DE-A93BA/SX BATTERY CHARGER 1 PP,PC 615 VPN7253 PAD D 1 EG,PP,PC,EC,EB,EE,GC,GH,
602 DE-A94BB/SX BATTERY CHARGER 1 GC,GH,GD GT,GN,GD
602 DE-A94CA/SX BATTERY CHARGER 1 GT 616 VPN7261 PAD B 1 EG,PP,PC,EC,EB,EE,GC,GH,
603 ----- BATTERY 1 EG,EC,EB,EE,GC,GH,GT,GN,GD, GT,GN,GD
PP,PC 617 VQL2C67-A OPERATING LABEL 1 PC
604 K1HY08YY0015 USB CABLE W/PLUG 1 (G3) 617 VQL2C68-1A OPERATING LABEL 1 GT
605 K1HY08YY0016 AV CABLE W/PLUG 1 (G3) 618 VQL2J61 GD LABEL 1 GD
606 VFC4634 SHOULDER STRAP 1 EG,PP,PC,EC,EB,EE,GC,GH, 619 VQL1Z76 NTSC LABEL 1 GT,GD
GT,GN,GD 650 K2CT3YY00034 AC CORD W/PLUG 1 EB,GC,GH
607 VFF0805 CD-ROM (INSTRUCTION BOOK) 1 PP,PC 651 K2CQ2YY00082 AC CORD W/PLUG 1 EG,EC,EE,GC
607 VFF0807 CD-ROM (INSTRUCTION BOOK) 1 EE,GC,GH,GN 651 K2CR2YY00026 AC CORD W/PLUG 1 GD
607 VFF0808 CD-ROM (INSTRUCTION BOOK) 1 GT,GD 653 K2CA2YY00129 AC CORD W/PLUG 1 GT
607 VFF0806 CD-ROM (INSTRUCTION BOOK) 1 EG,EC,EB 654 K2CJ2YY00052 AC CORD W/PLUG 1 GN
608 VGQ0C14 TOUCH PEN 1 (G3) 660 VFF0800-S CD-ROM (APPLI-OVERSEAS) 1 EG,PP,PC,EC,EB,EE,GC,GH,
609 VPF1100 BAG, POLYETHYLENE 1 (G3) GT,GN,GD
610 VQC8410 O/I SOFTWARE 1 EG [SPC] See "Notes"
(GERMAN/FRENCH/ITALIAN/
DUTCH)
610 VQC8408 O/I SOFTWARE 1 PP
(ENGLISH/SPANISH/
PORTUGUESE)
610 VQC8411 O/I SOFTWARE 1 EC
(SPANISH/PORTUGUESE/
SWEDISH/DANISH/FINNISH)
610 VQC8412 O/I SOFTWARE 1 EB,GN
(ENGLISH)
610 VQC8413 O/I SOFTWARE 1 EE
(RUSSIAN/UKRAINIAN)
610 VQC8414 O/I SOFTWARE 1 GC,GH
(ENGLISH/
CHINESE(TRADITIONAL)/
ARABIC)
610 VQC8415 O/I SOFTWARE 1 GT
(CHINESE(TRADITIONAL))
610 VQC8417 O/I SOFTWARE 1 GD
(KOREAN)
610 VQC8409 O/I SOFTWARE 1 PC
(ENGLISH/CANADIAN FRENCH)
611 VQT3N42 BASIC O/I 1 PC
(ENGLISH/CANADIAN FRENCH)
611 VQT3N43 BASIC O/I 1 EG
(GERMAN/FRENCH)
611 VQT3N44 BASIC O/I 1 EG
(ITALIAN/DUTCH)
611 VQT3N40 BASIC O/I 1 PP
(ENGLISH/SPANISH)
611 VQT3N41 BASIC O/I 1 PP
(PORTUGUESE)
611 VQT3N45 BASIC O/I 1 EC
(SPANISH/PORTUGUESE)
611 VQT3N46 BASIC O/I 1 EC
(SWEDISH/DANISH)
611 VQT3N47 BASIC O/I 1 EC
(FINNISH)
611 VQT3N48 BASIC O/I 1 EB
(ENGLISH)
611 VQT3N49 BASIC O/I 1 EE
(RUSSIAN/UKRAINIAN)
611 VQT3N50 BASIC O/I 1 GC,GH
(ENGLISH/
CHINESE(TRADITIONAL))
611 VQT3N51 BASIC O/I 1 GC
(ARABIC)
611 VQT3N52 BASIC O/I 1 GT
(CHINESE(TRADITIONAL))
611 VQT3N54 BASIC O/I 1 GN
(ENGLISH)
611 VQT3N55 BASIC O/I 1 GD
(KOREAN)
S-21
S7. Exploded View
S7.1. Frame and Casing Section
59
68
62
66
61
65
67
B21
B20
57
B55
90 B54
89
64
93-1 69
89-1 10 8 14
B57 60 B63 B64 13
B53
93 B56 63
B51 7
B12
91 B13 3 B52 15 B50 9 11
B14 12 2
B15 B61
75 82 B62
1
B48 56
B58
76 86 71
78 74 87
83
84 B49
B8 79 77 92 4
B42 B9 80
B43
B10 88 72 73 B17
17-3 81 B16
B11
B30 85 B18
17
17-8 B31 B32 16 B19
B60 B59
17-1 B33 5 B7
27 6
17-7
17-2 39 B40
17-9 B5 B41
37
B6 B1
17-6 33 B2
50
26 B36
17-4 21
34 28 35
17-5 32 30
29 31 42
B37 B44
22
B24 25 44
B45 41
B25 38 B3 43 40 46
18 B4
B26 B22 23
B38 B46
B23 45
B39
B27 36 24 B47
94
B34
B35
S-22
S7.2. Camera Lens Section (1)
213
207 B204
B205
B206
B207
208
204 B220
B221
B201
B222 B202
B203
B208
B209
202
B210
B211
206
209
210
B213
212
203
211
S-23
S7.3. Camera Lens Section (2)
305
313
B313
309
304
308 B317
310
B301 B303
B305 B302
B304
302
303
B306
B307
B318
B309
306
B311
B308
B310
B312
307
S-24
S7.4. Packing Parts and Accessories Section (1)
411 407
417
460
410
409
406
425
(DMC-G3KGN)
454 426
424 414
421
416
418
419
413
Directions for putting Color Labels,
NTSC LABEL and GD LABEL.
* Except black color model, stick each color label
(Ref. No.421,422,423) inside the “color indication frame”
making sure that the bottom part of the color label is 423
even inside the color indication frame. 422
* Stick NTSC LABEL (Ref. No.419) to printed “PAL” of the
packing case for [GD] and [GT] models.
* Stick GD LABEL (Ref. No.418) for [GD] model on the
original printed place.
S-25
S7.5. Packing Parts and Accessories Section (2)
511 507
517
560
510
503
509
531
530
529
506
528
Except PP,PC
(DMC-G3WEB/GC/GH) 515
550 P ,PC
tP 500
c ep
508 505 Ex
504
(DMC-G3WEC/EE/EG/GC/GD)
On
551 ly
PP
,P
C
525
(DMC-G3WGN)
554 526
524 514
521
516
518
519
513
Directions for putting Color Labels,
NTSC LABEL and GD LABEL.
* Except black color model, stick each color label
(Ref. No.521,522,523) inside the “color indication frame”
making sure that the bottom part of the color label is
even inside the color indication frame. 523
522
* Stick NTSC LABEL (Ref. No.519) to printed “PAL” of the
packing case for [GD] and [GT] models.
* Stick GD LABEL (Ref. No.518) for [GD] model on the
original printed place.
S-26
S7.6. Packing Parts and Accessories Section (3)
611
607
617
660
610
609
600
606
604
(DMC-G3EC/EE/EG/GC/GD)
651
On
ly 614
PP
,P
C
(DMC-G3GT)
653 616
(DMC-G3GN)
618
654
619
613
Directions for putting NTSC LABEL and GD LABEL.
* Stick NTSC LABEL (Ref. No.619) to printed “PAL” of the
packing case for [GD] and [GT] models.
* Stick GD LABEL (Ref. No.618) for [GD] model on the
original printed place.
S-27